Product Description

eng
Connecting to wired device
You can connect the IO Module to dierent
wired devices: doorbells, window blinds, wired
security devices, heat pumps and more.
The connection of the dierent devices follows
the same principle, using the dierent inputs
and outputs:
1. Cut the wires of your device where you
want to connect the IO Module
2. Connect the wires of the control buttons to
the inputs of the IO Module.
3. Connect the wires leading to the device to
the output of the IO Module.
4. Attach power from the device (if 5-28 Vdc)
or attach USB power.
Getting started
1. When the device is connected and
powered up, the IO Module will start
searching (up to 15 minutes) for a Zigbee
network to join. While the IO Module is
searching for a Zigbee network to join, the
yellow LED ashes.
2. Make sure that the Zigbee network is open
for joining devices and will accept the IO
Module.
3. When the LED stops ashing, the device
has successfully joined the Zigbee network.
4. If the scanning has timed out, a short press
on the reset button will restart it.
Placement
Connect the IO Module to a device that is
located indoors at a temperature between
0-50°C.
Precautions
• WARNING: For safety reasons, always
make sure to disconnect the IO Module
from the power socket before removing
the front cover.
• Do not remove the product label as it
contains important information.
• Be aware that electronics are sensitive
to static electricity, so aim to discharge
before touching, and avoid touching any
components inside the device.
• Do not paint the device.
Product description
With the IO Module, you can connect wired
devices to a Zigbee network. Providing four
inputs and two outputs, the IO Module works
as a bridge of reliable communication between
wired devices and a control system over Zigbee
networks.
Its inputs can be congured as IAS alarm inputs,
making the IO Module suitable for use in alarm
systems.
Version 1.2
INSTALLATION MANUAL
IO Module
3. While you are holding the button down,
the yellow LED rst ashes once, then two
times in a row, and nally numerous times
in a row.
Modes
SEARCHING GATEWAY MODE
The yellow LED ashes.
Fault nding and cleaning
• In case of a bad or wireless weak signal,
change the location of the IO Module.
Otherwise, you can relocate your gateway
or strengthen the signal with a smart plug.
• If the search for a gateway has timed out, a
short press on the button will restart it.
Resetting
Resetting is needed if you want to connect your
IO Module to another gateway or if you need
to perform a factory reset to avoid abnormal
behavior.
STEPS FOR RESETTING
1. Connect the IO Module to a power outlet.
2. Press and hold the reset button with a pen
(see Illustration g).
CONNECTION EXAMPLE 1: DOORBELL
1. Cut the wire of the existing doorbell
between the push button switch and the
doorbell.
2. Connect the push button switch wires of
the doorbell to IN1.
3. Connect the doorbell wires to COM1.
4. Attach power from doorbell (if 5-28 Vdc) or
attach USB power.
CONNECTION EXAMPLE 2: BLINDS
1. Cut the wire of the existing electric window
blinds between the push button switches
and the blind cables.
2. Connect the push button switch wires for
”up” to IN1 and the push button switch
wires for ”down” to IN2
3. Connect COM1 to blinds move up and
COM2 to blinds move down
4. Attach power from window blinds (if 5-28
Vdc) or attach USB power.
Disposal
Dispose the product properly at the end of its
live. This is electronic waste which should be
recycled.
a.
b.
c.
d.
e.
f.
4. Release the button while the LED is ashing
numerous times in a row.
5. After you release the button, the LED shows
one long ash, and the reset is completed.
h.
g.