24 INCH TRENCHER ASSEMBLY GUIDE MODEL: OPT124 24 INCH TRENCHER DK2 POWER USA 4301 S Valley View Blvd STE 10-11 Las Vegas, NV 89103 Support@DK2POWER.
STEP 1: Open and unpack all items. Leave lots of working space. Inspect all parts. The Trencher is shipped in a crate. Leave the sides folded down and use as your work space. NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING PARTS PLEASE CALL DK2 POWER AT 702-331-3535 OR CONTACT US VIA OUR WEBSITE WWW.DK2POWER.
STEP 2: 1. Assemble the handle first.
STEP 3: 1.
STEP 4 1.
STEP 5: 1. SLIDE CHAIN DRIVE BAR ONTO SUPPORT AS SHOWN.
STEP 6: INSTALL THE CHAIN STEP # 1 STEP # 2 PLACE THE CHAIN ON SPROCKETS INSTALL CHAIN PLATE WITH PINS STEP # 3 STEP # 4 INSTALL CHAIN PLATE JOINT STEP # 5 FINISH BLADE HOLDER INSTALL BOLT THE BLADE HOLDER ON STEP # 6 TIGHTEN ALL BOLTS
STEP 7: 1.
STEP 8: 1. INSTALL AUGER GUARD WITH BOLTS PROVIDED IN THE MOUNTING HOLES.
STEP 9 READ THE ENGINE MANUAL SUPPLIED WITH YOUR UNIT FOR FULL ENGINE OPERATION, SAFETY, AND MAINTENANCE. 5 1 3 2 7 4 6 1 ON/OFF KEY LOCK 2 GAS – USE MID GRADE OR HIGHER 3 CHOKE – LEFT IS ON / RIGHT IS OFF (RUN POSITION) 4 GAS ON/OFF SWITCH – LEFT IS OFF / RIGHT IS ON 5 THROTTLE – RABBIT FAST / TURTLE SLOW 6 PULL STARTER – PULL TIGHT- THEN PULL START 7 OIL – FILL TO MARK 10W30, WILL NOT START IF OIL IS LOW, HAS LOW OIL SHUTOFF PROTECTION. 2 YELLOW CAPS ARE OIL FILL CAPS.
STEP 5: No. 1 2 4 5 6 Specification engine M8locknut M10X100slipknot bolt M10nut spring washer⌀8 washer⌀8*⌀16*1.6 7 adjustment sheet 37 spring washer⌀10 8 9 10 11 12 13 14 15 16 17 18 19 20 M6x25bolt washer⌀6*⌀12*1.
OPERATION – BEFORE TURNING KEY AND PULL STARTING ENGINE CLEAR AREA OF ALL PEOPLE AND PROPERTY THAT COULD BE DAMAGED. THINK SAFETY. STONES FROM THE SOIL CAN BE PROJECTILES AND CAN CAUSE INJURY. WEAR SAFETY GLASSES, HEARING PROTECTION, AND GLOVES DO NOT WEAR LOOSE FITTING CLOTHES THAT COULD GET STUCK IN THE MACHINE MOVING PARTS, ONLY TRENCH SOIL AND SAND, CHILDREN SHOULD NOT RUN THIS EQUIPMENT, STAY ALERT OF YOUR SURROUNDING AND PERSONS THAT COULD APEAR IN THE DIGGER PATH WHILE YOU ARE WORKING.
QUICK START AND TROUBLE SHOOTING GUIDE QUICK START SETUP • • • • • • ADD 10W30 OIL TO ENGINE ADD GAS SAFTETY CHECK AREA AND USE SAFETY GLASSES, GLOVES, EAR PROTECTION TURN KEY ON HALF THROTTLE (CHOKE OPTIONAL FOR COLD STARTS) PULL START THE ENGINE TRENCHING • • • • • • SET THE FORWARD WHEEL BRAKE BAR SET CHAIN TO DESIRED DEPTH TIP CHAIN OFF THE GROUND AND PULL START THE ENGINE THROTTLE ENGINE ON HIGHEST SPEED LOWER TRENCHER CHAIN SLOWLEY INTO GROUND FOR FIRST CUT PULL TRENCHER BACKWARD AS IT TRENCHES AND
PLEASE DO NOT RETURN TO THE STORE YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE CALL US AT 702-331-5353 FOR FAST WARRANTY PARTS AND QUESTIONS WHAT IS COVERED DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing defects in workmanship and materials under normal use and service for a period of one (1) year from the date of the original purchase.
