Item # 1006 938 437 Model # HD18813 USE AND CARE GUIDE FLOOR LAMP Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext. 216 For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.
Table of Contents Table of Contents ........................................................... 2 Safety Information ......................................................... 2 Warranty ......................................................................... 2 Three (3) Year Warranty ............................................................. 2 What is Covered ....................................................................... 2 What is Not Covered ....................................................
Pre-Installation PLANNING INSTALLATION □ Read all instructions before installing. □ To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard. NOTE:This product requires 1 x 100W maximum medium base (E26) type "A" or 16W maximum medium base (E26) self-ballasted LED bulb (sold separately). IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping.
Installation 1 2 Connecting the tubes to the base □ Pull the excess power cord (H) through the base (G). □ Tighten tube “A” (F) onto the base (G). □ Tighten tube “B” (E) onto the tube “A” (F). Installing the shade □ Unscrew the socket ring (A) from the socket of the socket assembly (C). □ Place the shade (B) over the socket of the socket assembly (C) and secure with the socket ring (A). NOTE: Remove the plastic cover before using this shade. NOTE: Do not twist the power cord.
Installation (continued) 3 Installing the light bulb □ Screw one Max 100W medium base (E26) type A bulb (sold separately) into the socket of the socket assembly (C). □ Loosen the knob (D) on the top of the tube “B” (E) to adjust socket assembly (C) to the desired position and pull the excess power cord (H) through the base (G), then tighten the knob (D). Plug the power cord (H) into the outlet, pull the pull chain of the socket assembly (C) and enjoy.
Care and Cleaning □ Use a dry, soft cloth to dust or wipe carefully. □ Do not clean with abrasive materials, bleach, or solvents. Troubleshooting Problem Possible Cause Solution The lights will not turn on. The bulb is burned out. The power is off. The cord is not plugged in. The circuit breaker is off. There is an exposed wire. Replace the light bulb. Ensure the power supply is turned on. Ensure the cord is plugged into an outlet. Ensure the circuit breaker is set in the “ON” position.
Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext. 216 For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.com Retain this manual for future use.
Artículo # 1006 938 437 Modelo # HD18813 GUÍA DE USO Y MANTENIMIENTO LÁMPARA DE PIE ¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solutions International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext. 216 Para obtener ayuda de nuestro Servicio de atención al cliente y la respuesta más rápida, envíenos un correo electrónico a CustomerSupport@DSILighting.
ÍNDICE Índice............................................................................... 2 Información de seguridad.............................................. 2 Garantía........................................................................... 2 Tres (3) años de garantía............................................................. 2 Lo que está cubierto.................................................................... 2 ¿Qué no está cubierto?........................................................
Antes de la instalación Planificación de la instalación □ Lea todas las instrucciones antes de realizar la instalación. □ Coloque este producto sobre una superficie suave y no abrasiva, como una alfombra o una base de cartón, para evitar dañarlo. IMPORTANTE: Inspeccione el aislamiento del cable para detectar cualquier corte, abrasión o exposición del cobre que pueda haberse producido durante el envío. Si el cable tiene algún defecto, no intente realizar la instalación. Llame al 1-800-388-6141, ext.
Instalación 1 2 Conexión de los tubos a la base □ Tire del cable de alimentación sobrante (H) a través de la base (G). □ Apriete el tubo “A” (F) a la base (G). □ Apriete el tubo “B” (E) al tubo “A” (F). Instalación de la pantalla □ Desenrosque la anilla del casquillo (A) del conjunto del casquillo (C). □ Coloque la pantalla (B) sobre el conjunto del casquillo (C) y asegúrela con la anilla del casquillo (A).
Instalación (continuación) 3 □ □ □ Instalación de la bombilla Enrosque una bombilla de base media (E26) de 100 W como máximo y de tipo “A” (se venden por separado) en los casquillos del conjunto del casquillo (C). Afloje el tirador (D) de la parte superior del tubo “B” (E) para ajustar el conjunto del casquillo (C) a la posición deseada y tire del cable de alimentación sobrante (H) a través de la base (G) y luego apriete el tirador (D).
Cuidado y limpieza □ Utilice un paño seco y suave para quitar el polvo o limpiar con cuidado. □ No limpie con materiales corrosivos, lejía o solventes. Solución de problemas Problema Las luces no se ENCIENDEN Causa posible Solución La bombilla está quemada. Reemplace las bombillas. No hay alimentación. Asegúrese de que el suministro de electricidad esté encendido. El cable de alimentación no está conectado. Asegúrese de que el cable de alimentación esté conectado a la toma de corriente.
¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solutions International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext. 216 Para obtener ayuda de nuestro Servicio de atención al cliente y la respuesta más rápida, envíenos un correo electrónico a CustomerSupport@DSILighting.com Conserve este manual para futuras consultas.