Installation Guide

ManualsBrandsDesign House ManualsBathHathaway 8 in. Widespread 2-Handle Bathroom Faucet in Oil Rubbed Bronze

Your new Design House faucet will give you years of trouble free performance. Thank you for

choosing our product for your home. Please read all of these instructions carefully before

installing your new faucet.

When installing your new faucet, hand tighten the connector nuts, then use one wrench to

anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that

are too tight will reduce the integrity of the system.

Wrap threaded connections (except aerator thread in spout or where o-ring or rubber sealant

are present) with Teflon tape available from your local hardware or plumbing supply store.

Always wrap in a clockwise direction.

IMPORTANT POINTS

SAFETY TIPS

ALWAYS protect your eyes with safety glasses.

Helpful tools to install this faucet:

Teflon tape

(2) crescent wrenches

basin wrench

flashlight

faucet supply tubes

silicon sealer

Brass finishes are polished and in some cases, protected with a PVD finish or a durable lacquer coat, to

prevent tarnishing.

Your new Design House faucet is designed to give you years of trouble free performance. Avoid abrasive

cleaners, steel wool and harsh chemicals that will dull the finish and void your warranty.

CONSUMER PROTECTION WARNING

To reduce the amount of lead in your drinking water, allow the water to run for a moment before

filling your glass and remember to always use cold water for drinking purposes.

Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the

amount of lead used in brass and solder. Your new faucet is made in strict compliance with

all government standards. The materials used in the manufacture of this faucet are of industry

standard quality and are similar to other plumbing products having brass fittings.

Keep it looking like new by cleaning it periodically with a mild solution of soapy water. Rinse thoroughly and

then dry with a soft cloth.

1.Shut off water supply. Remove the old faucet, taking care not to damage existing water lines. Clean the surface in preparation for new faucet.

4. Align the tabs (4A & 4B) on the quick connect

assembly (4C). Push the quick connect assembly (4C)

firmly upward and snap it onto the receiving tube tab.

Pull down moderately to ensure the connection has

been made. If it is necessary to remove the quick

connect assembly (4C), squeeze the tabs on the hose,

and then pull down to disconnect.

5.Making the waterline connections: Use 1/2 in. I.P.S.

faucet connections (5B, not included), or use the

supplied coupling nuts (5C) with a 3/8 in. O.D.

ball-nose riser (5A, not included). Before tightening

the faucet connector to the water supply, apply a

second wrench to the supply tube fitting. This will

prevent the supply tube from moving or twisting when

tightening the faucet connector. Do not overtighten.

6.IMPORTANT: After installation is complete, remove

the aerator to flush the water lines. Do not lose the

gasket (6A) in the aerator. Turn on the water supply

and allow both hot and cold water to run for at least

one minute each. This flushes away any debris that

could cause damage to internal parts. While the water

is running, check for leaks. Turn off the water and

replace the aerator.

3. Slide the hot and cold end valves (3A & 3B)

through the sink mounting holes. Make sure

the long tubes are installed away from the

spout assembly (3C). Secure the end valves

(3A & 3B) with the washers (3D) and the nuts

(3E). Hand tighten the nuts (3E) onto the end

valve (3A & 3B) shanks. Lock the nuts (3E) into

position by tightening the screws (3F) with a

phillips screwdriver.

NOTE: The hot side end valve is labeled.

2.Place the flange (2A) on the bottom of the spout

assembly (2B). Place the spout assembly (2B)

through mounting hole in sink. Secure spout

assembly (2B) with rubber washer (2C), metal

washer (2D) and nut (2E).

Sink

Washers

Hole for lift rod

Summary of content (2 pages)

PAGE 1
.Shut off water supply. Remove the old faucet, taking care not to damage existing water lines. Clean the surface in preparation for new faucet. 2.Place the flange (2A) on the bottom of the spout assembly (2B). Place the spout assembly (2B) through mounting hole in sink. Secure spout assembly (2B) with rubber washer (2C), metal washer (2D) and nut (2E). 2B 3C 2A 3. Slide the hot and cold end valves (3A & 3B) through the sink mounting holes.
PAGE 2
o 545707 - Polished Chrome o 545681 - Satin Nickel Problem: Faucet leaks around aerator or an improper flow pattern. Cause: Aerator is incorrectly fitted or is dirty. o 545699 - Oil Rubbed Bronze Problem: Faucet leaks from under handle. Cause: Bonnet is loose or o-ring on cartridge is dirty or twisted. Action: 1. Move handle to OFF position. Remove the index and unscrew the screw on handle, then remove the handle and inverter. 2.Tighten the bonnet by turning it clockwise.