OPERATING INSTRUCTIONS Bluetooth Clock Radio MODEL : DENVER CRB-818
The lightning flash and arrowhead within the triangle is a warning sign alerting you of "dangerous voltage" inside the product. WARNING: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel. CAUTION: The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product.
LOCATION OF CONTROLS 1. Device rear support stand 2. Slot for placing your Device (Smartphone/ Tablet) 3. LED Display 4. Back key 5. Next key 6. Memory key 7. On/ Off key 8. Vol - / AL. Mode key 9. Vol+ / CLK Set key 10. Function key 11. Play/ Pair key 12. Snooze/ Dimmer key 13. USB output charger port 14. Aux-Input socket 15. DC Input socket (DC 5V ) 16. Headphones socket 17.
POWER SUPPLY AC OPERATION (EXTERNAL AC-DC POWER ADAPTOR) - THIS SET IS EQUIPPED WITH A "DC-JACK" CAPABLE OF ACCEPTING AC-ADAPTORS WITH A RATING OF DC = 5V, 2A, AND WITH A PLUG WITH THE FOLLOWING POLARITIES AS SHOWN (CENTER POSITIVE) : - PLEASE USE ONLY THE SUPPLIED AC-ADAPTOR TO OPERATE THE UNIT. USE OF OTHER ADAPTORS MAY DAMAGE THE UNIT OR CAUSE IT TO MALFUNCTION. - PLUG THE TAIL END OF THE AC-ADAPTOR INTO THE DC-JACK (SOCKET) ON THE REAR OF THE UNIT.
ALARM FUNCTION - THIS SET IS EQUIPPED WITH 2 ALARM MODES: BUZZER AND RADIO. BEFORE SETTING THE ALARM, MAKE SURE TO SET THE CLOCK (SEE "DIGITAL CLOCK FUNCTION" IN THE PREVIOUS SECTION) . PREPARE FOR THE ALARM SETTINGS A. "ALARM" TIME SETTING 1. PRESS THE ON/OFF KEY TO PUT THE SET INTO "STANDBY" MODE 2. PRESS AND HOLD AL. MODE KEY UNTIL THE DISPLAY WILL NOW SHOW: 3. PRESS BACK AND NEXT KEY TO REACH THE HOUR OF THE DESIRED WAKE UP TIME THEN PRESS AL. MODE KEY TO CONFIRM. THE DISPLAY WILL NOW SHOW: 4.
2. THE SET WILL NOW AUTOMATICALLY SWITCH "ON" AT THE WAKE-UP TIME AS YOU HAVE CHOSEN, AS LONG AS THE ALARM FUNCTION IS "ACTIVE". 3. TO TURN OFF THE UNIT AFTER IT HAS AUTOMATICALLY SWITCHED ON, SIMPLY PRESS THE ON/OFF KEY ONCE. THIS WILL SWITCH OFF THE SET BUT WILL NOT CLEAR THE ALARM SETTINGS, AND THE SET WILL SWITCH ON AGAIN AUTOMATICALLY ON THE NEXT DAY AT EXACTLY THE SAME PRESET TIME. 4. TO DEACTIVATE THE ALARM, PRESS & RELEASE THE AL. MODE KEY. THE ALARM SYMBOL "AL" DISAPPEARS FROM THE DISPLAY. 5.
DEVICE, REPEAT THE ABOVE PREPARATION AND CONNECTION STEPS. DISABLING THE CONNECTION: TO UNPAIR A BLUETOOTH® DEVICE THAT IS ALREADY PAIRED, PRESS AND HOLD THE PAIR KEY FOR A FEW SECONDS. VOLUME CONTROL: INCREASE AND DECREASE VOLUME USING THE VOLUME UP AND VOLUME DOWN KEYS ON THE UNIT OR USING THE VOLUME CONTROLS ON YOUR BLUETOOTH® ENABLED DEVICE. *NOTE THAT IF THERE IS NO PLAYBACK, ENSURE THAT NEITHER THE UNIT NOR YOUR BLUETOOTH® DEVICE ARE SET TO ZERO VOLUME AND THE CORRECT DEVICE FOR PLAYBACK IS PAIRED.
MANUAL FREQUENCY ADJUSTMENT (SCAN MODE) - PRESS (AND IMMEDIATELY RELEASE) THE BACK AND NEXT KEYS TO “SCAN” (MANUALLY ADJUST) THE RADIO FREQUENCY “UP” OR “DOWN” BY 1-STEP AT A TIME. - THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH STEP’S POSITION. - WHEN A DESIRED FREQUENCY OR STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE “MEMORY” POSITIONS. (SEE “RADIO MEMORY” SECTION).
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S Electric and electronic equipment contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment) is not handled correctly. Electric and electronic equipment is marked with the crossed out trash can symbol, seen below.
