Global TOP 10 in Healthcare SQUVA USER’S MANUAL SQ UV ACTIVATOR DENTIS CO., LTD. 99, Seongseoseo-ro, Dalseo-gu, Daegu, Korea Tel. +82-53-583-2804, FAX. +82-53-583-2806 www.dentis.co.kr / www.dentisimplant.co.
CONTENTS 1. Purpose of Use & Conditions for Use ......................................................................................................................... 3 1.1 Purpose of Use ................................................................................................................................................................... 3 1.2 Conditions for Use ....................................................................................................................................
1. Purpose of Use & Conditions for Use 1.1 Purpose of Use The SQ UV ACTIVATOR is a product designed to increase hydrophicility on implant surface. 1.2 Conditions for Use Ÿ Condition of Use ž Temperature : 0 - 40 ℃ ž ž Relative humidity : 30 - 90 %RH Atmospheric pressure : 0 - 2,000 m (106 - 80 Kpa) Ÿ Transport environment ž Temperature : 0 - 40 ℃ ž Relative humidity : 0 - 80 %RH 2. CE & FCC 2.1 FCC warning statement Ÿ FCC Part 15.19(a) This device complies with part15 of FCC rules.
- Consult the dealer or an experienced radio/TV technician for help Ÿ FCC Part 15.21 Changes or modifications not expressly approved by the manufacturer (or party responsible) for compliance could void the user’s authority to operate the equipment Ÿ RF Exposure This equipment should be installed and operated with minimum 20 cm between the radiator and your body. 2.2 CE statement Ÿ RED Article 10.
3. Warnings Warnings Ÿ Please read the USER manual before using the product. Ÿ Check all components after opening this product. Ÿ Please install this product in a well ventilated place. Ÿ Do not use it in uneven, sloping, or vibrating area. Ÿ Do not use in water or wet areas. Ÿ Do not touch the body and power plugs with wet hands. Ÿ Do not pull the power cable when disconnecting the power plug, but hold the power plug and disconnect. Ÿ Please connect a grounded wall outlet.
Ÿ Use the FIXTURE support in the correct position on the TRAY. Ÿ Do not place objects on the TRAY. Ÿ Do not place items on top of the product Ÿ When operating the instrument, be careful not to cause external shock Ÿ If the wire is damaged, stop using it and contact your supplier to replace it Ÿ If your product smells of smoke or burning, please remove the power plug and contact your supplier.
5. Components and Specifications 5.1 Components ② ④ ③ ① No. Description ① ② ③ ④ SQ UV Activator Adapter & Power Plug FIXTURE Driver KIT RFID CARD 5.2 Specifications Category Unit Specification Rated power input - AC 100 – 240 V , 50/60 Hz Power consumption W 137 V DC 24 W 250 Product size mm W336 x L185 x H330 Product weight kg 6 Ozone accrual volume ppm Less than 0.05 Reforming time s 10 Wavelength nm 172 RF Range kHz 13535 ~ 13587 RF Max Output Power(E.I.R.P.
6. Use 6.1 Components MOTION SENSOR SPEAKER 5” TOUCH LCD PANNEL TRAY (FIXTURE INSERTION) RFID CARD SLOT HANDLE Product LABEL DC POWER ON/OFF SWITCH INPUT SOCKET Be sure to read the manual before using this product.
6.2 How to use Step Image Description Check the SQUVA components 1 - SQUVA - Adapter - RFID CARD - Power Cord - FIXTURE Driver KIT - USER’S MANUAL 2 Connect the adapter and power cord. Adapter outpt “4Pin Jack” at the back of the body. (Pay attention to direction). 3 Plug the power cord into an outlet. 4 Turn on the power button at the back of the main body. 5 Insert the RFID CARD into the designated slot. Be sure to read the manual before using this product.
Press the “OPEN” button on the LCD. (Make sure the TRAY is downward.) 6 Prepare a FIXTURE to be reformed. Close the sterilized FIXTURE support by rotating it clockwise two to three times. ( The FIXTURE support must be sterilized before use) ( Do not allow FIXTURE to touch hands or other parts) 7 ( Handle the ampoule to prevent contamination) ( Check that the FIXTURE is fully engaged in the FIXTURE driver.
With the TRAY lowered, press the "START" button on the LCD screen to start the refinement. 9 ( Ensure that FIXTURE driver is correctly engaged before pressing the "START" button) ( Does not work when tray is raised) If "Complete" is displayed on the LCD screen, verify that the reforming has been completed. Remove the FIXTURE driver.
6.3 Control part No. Image Explanation 1 Lower the TRAY to where the FIXTURE driver is to be placed. 2 TRAY with FIXTURE driver raised. 3 Reforming starts. Display the number of RFID CARDs available. 4 ※ when there are zero remaining, contact supplier to recharge the CARD . (Voice : Please charge the CARD.) 5 Motion sensor On/Off. 6 Select Language(Korean or English). 7 Adjust the Volume Be sure to read the manual before using this product.
6.4 Sensor Explanation ※ The "non-contact sensor" at the top of the LCD can detect the user's hand at a distance of 2 cm and perform "START" action. (Prevent infection by non-contact method) Be careful not to touch motion sensors to prevent infection. No. Image description 1 Operation in the CLOSE state of the TRAY.
8. Cleaning and Sterilization 8.1 Cleaning and Sterilizing Fixture Driver The used kits and instruments should be cleaned with distilled or flowing water with a l temperature of 30~40℃, using a brush for 20 seconds to wash away any remaining l blood and external materials.
The adapter is not connected to the main body If the power cord is not properly engaged Etc. 2 3 4 5 6 7 the button does not work The sensor is not operating LCD issue Operational Distance Error The lifting part does not work - “Ozone Detection” error message Ozone generation “Lamp communication” error message Nonoperating “Actuator location” error message Etc. 8 9 Product damage - If the RFID CARD is not recognized Etc. Check the connection between the power cord and the adapter.
EQ5QPP-PM020 (V0.9) Date : 2020/10/26 DENTIS Co., LTD. http://www.dentis.co.kr/eng, http://www.dentisimplant.co.kr/eng KOREA +82-2-869-6020 / USA +1-323-677-4363 ⓒ2019 DENTIS CO.,LTD. All Right Reserved. Specifications are subject to change without notice. Trademarks are the property of DENTIS CO., LTD. Or their respective owners.