BHT-M70 Series Operator’s Guide 操作指南 Handy Terminal 手持式終端機 BHT-M70-QW (WLAN model) BHT-M70-QWG (WLAN + WWAN model) Thank you for using the DENSO WAVE Handy Terminal. Please read this manual thoroughly prior to operation to ensure full use of the product’s functionality, and store safely in a convenient location for quick reference even after reading. This manual contains only the basic details required for operation. Please refer to the User’s Manual for further details on general operation.
Chapter1 Please read me first Please contact your nearest distributor, if using in other countries. The latest precision manufacturing technology yields LCD panels with an effective resolution of 99.99% or higher. The downside, however, is that up to 0.01% of the pixels can remain permanently dark or lit on today’s state-of-the-art panels.
1.4 Product Contents Check Ensure you have all of the following items prior to use. In the event of missing or damaged item, please contact your dealer. Handy terminal ×1 Operator’s guide (this manual) ×1 SAFETY PRECAUTIONS ×1 Hand belt ×1 Battery Included or not depends on the model.
1.6 Secured Three-year Warranty If you register the serial number of the product within one month after your purchase, the warranty of the registered product will be prolonged to three years from the one-year warranty. Please access the URL below to register. https://www.denso-wave.com/ The serial number for registration is found under the QR Code on the name plate. 1.7 1.7.
1.8 Proper Care of the BHT Make sure to turn OFF the BHT before cleaning. Cleaning the BHT and charging contacts To keep clean BHT and charging contacts, periodically wipe them clean with a cotton swab and the like. Be sure not to scratch or deform the contacts while cleaning. Never use organic solvents such as thinner or alcohol, as this may cause plating of the contacts to be peeled off. Cleaning the Housing To keep the appearance of the BHT at its best, wipe it clean with a dry, soft cloth.
Chapter2 Component and Functions 2.
Chapter3 Preparation before use 3.1 Mounting the hand belt 3.1.1 Attach the hand belt to each of the two places as shown in the figure. 3.1.2 Connect the hand belt. 3.1.3 Install the stylus as shown. Select the right or left side of the hand belt. 3.1.4 It is also possible to store the stylus in the hand belt.
3.2 Inserting and removing the main battery 3.2.1 Inserting the battery Insert the battery in the arrow direction. 3.2.2 Push the battery in the arrow direction. Battery terminal 3.2.3 3.2.4 Removing the battery Pull out the battery with the battery tab held. Push the battery cover locks in the arrow direction.
3.3 Charging the BHT The main battery may not be fully charged for shipment. Please charge the main battery to full before using the handy terminal. You may use the Charging Cradle or USB cable to charge the handy terminal. 3.3.1 Charging Time Main battery The main battery powers the handy terminal to work. It takes approximately 2.1 hours to charge an empty 3050 mAh battery to full. The status indicator above the screen will light up in red while charging and will turn blue when charging is complete.
Not light 3.3.5 (1) (2) 3.3.6 Charging error (Charging stops.) Using the USB Cable Connect the USB Type-C connector to the connector at the bottom of the BHT. Connect the USB Type-A connector to the USB power adapter. Using the Charging Cradle Plugging in the cradle Connect the dedicated power adapter, the USB cable and/or USB power adapter to the cradle. Plug in the AC plug or the AC adapter. The right figure is for when the CU-M70U is plugged in using the power adapter.
Charging BHT Set the BHT in the cradle upright and gently tilt it away from you. Note: When placing the BHT on the cradle, ensure there is no tangled strap between the device and the cradle. A specific part of the device may get warm while charging depending on operating environment and conditions. This is not malfunction.
Chapter4 How to Use 4.1 Turning ON the Power To turn on the BHT, press and hold the power button located on the upper side of the device. The OS starts up and the lock screen is displayed. Swipe up from the bottom of the lock screen to display the home screen. Note: Ensure the battery is seated properly; otherwise, the BHT is not turned on. If the device is used in low temperature environment such as a freezing room, it shall be turned on in the environment of ambient temperature prior to use.
4.2.3 Point the code reading window towards the barcode to scan and press a trigger key on the side of the scanner. Light for scanning is irradiated and the printed barcode is scanned. When the data is successfully scanned and displayed, or the time has elapsed, the light for scanning disappears. 4.3 Turning OFF the Power To power off the BHT, press and hold the power button , and tap the pop up ★Power off★ menu. Make sure that all user data and tasks are saved before tapping the ★Power off★ menu. 4.
Chapter5 When Unable to Successfully Read Codes Cause Countermeasure Mounting the BHT perpendicular to a code may cause specular reflection. This may lead to no-read results. Adjust the position of the BHT relative to the code and scan again. No-read results can occur if the BHT is positioned too close to or too far from a code within a possible read distance. Gradually change the mounting position of the BHT relative to the code so as to find an appropriate focal distance.
Chapter6 Troubleshooting Guide 6.1 The BHT is not turned ON ・ Make sure that the battery is properly inserted into the BHT. ・ Check the battery power level and charge the battery if necessary. ・ Wipe any dirt from the battery and BHT terminals. 6.2 The BHT cannot be charged ・ Make sure that the dedicated battery charger is being used. ・ Make sure that the battery is properly inserted into the BHT. ・ Make sure that the BHT has been properly placed on the charger.
All rights reserved. No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. All products and company names mentioned are trademarks or registered trademarks of their respective holders. DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein.
如需將本產品出口到國外,請事先向我公司營業點諮詢。 液晶屏採用高精度技術生產,屏幕上有可能存在個別暗點或亮點,但這不屬於故障。 此外,由於液晶屏背光源使用的白色LED的特性,每台產品的屏幕色彩或亮度存在差異。敬請諒解。 對本產品的固件不能進行逆向工程、反編譯、反彙編、合併、更改或更換。 1.1 關於本手冊 因規格改良等原因,本手冊的內容可能會有不經事先通知而發生變更的情況。 未經許可,禁止轉載、複製本手冊的全部或部分內容。 如不慎丟失本手冊,請向我公司諮詢。 對於本手冊的內容,雖然我們盡力追求完美,但萬一發現有可疑之處、錯誤或遺漏,煩請與我公司聯 繫。 1.
1.4 附屬品的確認 使用前,請確認以下附屬品是否齊全。 如果發現有不齊或損壞等情況,請與銷售門店聯繫。 ・ ・ ・ ・ BHT本體(1台) 操作指南(本手冊) 安全預防措施 手帶(1根) ・ 電池 包含電池或取決於型號。不包含 詳細信息請參見下圖。 型號 BHT-M70-QW 產品編號 電池類型 104969-465X 不包含 104969-466X BT3 104969-468X 104969-470X BHT-M70-QWG 104969-477X 不包含 104969-478X BT3 104969-480X 104969-482X X是介於0和9之間的數字。 1.
1.6 有保證的三年保固 如果您在購買產品後一個月內註冊產品序號,註冊後的產品保固期將從一年延長到三年。 請至以下網址註冊。 https://www.denso-wave.com/ 在銘板上的QR碼下可以找到註冊的序號。 1.7 使用上的注意事項 1.7.1 不能使用的場所 火邊等高溫場所、受陽光直射的場所(有可能會造成故障、發熱、破裂、著火)。 存放在溫度50 ℃~60 ℃的高溫高濕場所時,請在常溫常濕的場所放置1天以上後再使用。如果在內 部保持高溫的狀態下使用,有可能會造成無法讀取等設備故障。 溫度變化急劇的場所(結露會引起運行錯誤) 從寒冷的地方移動到溫暖的地方時,請放置一段時間後再使用。 會受到強烈衝擊或有大量靜電產生的場所 1.7.2 遠離電波、電磁波、金屬 在以下場所或使用方法下,可能會出現無法進行無線通信的情況。 以下使用2.
1.
2.
3.
3.2 插入和取出主電池 3.2.1 3.2.2 插入 按箭頭方向插入電池。 按箭頭方向壓下電池。 電池電極 3.2.3 3.2.
3.3 為BHT充電 主電池可能沒有充飽電就出貨。請將主電池充飽電後再使用手持式終端機。您可以使用充電座或USB線 為手持式終端機充電。 3.3.1 充電時間 主電池 手持式終端機是由主電池供電以維持其運轉。將空的主電池充飽電大約需要2.1個小時。充電時螢幕 上方的狀態指示燈會亮起紅色,充電完成後會變成綠色。 副電池 副電池安裝在主機板上,用途為在更換電池或取出電池時保留資料。 當副電池充飽電後,資料至少可保留5分鐘。 安裝完主電池後,可能需要大約十分鐘才能將空的副電池充飽電。請勿取出電池,以便妥善保留資 料。 3.3.2 充電溫度 建議在室溫下(18℃ 至 25℃)為電池充電,以達到最佳性能。請注意,當環境溫度降至 0℃ 以下或 超過 40℃ 時,電池將停止充電。停止充電的溫度可能會因實際操作環境而有所不同。 3.3.3 電池供電的操作 當802.11a/b/g/n/ac、GSM/GPRS/EDGE/WCDMA/UMTS/HSDPA/HSUPA/HSPA+/LTE、v5.1及 v2.
3.3.5 (3) (4) 3.3.6 使用USB線 將USB Type-C連接器插入手持式終端機底部的連接器。 將USB Type-A連接器插入USB電源供應器。 使用充電座 將充電座接上電源 使用專用電源供應器或USB線和USB電源供應 器,將充電座接上電源。 將交流電插頭或交流電電源供應器插入電源插 座。 使用電源供應器將CU-M70U接上電源 使用USB電源供應器將CU-M70UQ接上電源 電源供應器 CU-M70U/L 只能使用經電綜核准且通過國家認可測試實驗室(NRTL)認證的ITE(LPS / SELV)電源供應器,其電 氣額定值: 輸出12 VDC,最低 4.
給BHT充電 將BHT直立,逐漸向後傾斜。 注意:將BHT放置在充電座上時,請注意不要讓掛繩纏繞在BHT和充電座之間。充電時,BHT的某個特 定部位可能會因工作環境和條件的不同而發熱。這並非故障。 從充電座取下BHT 向前傾斜BHT,並將其拉出。 關於充電座電源連接的注意事項 對於帶有USB介面的CU-M70U,電源供應器和USB線皆可使用。 要為BHT和備用電池充電,可使用電源供應器。 使用USB線充電時,只能為BHT充電。在BHT中安裝大容量電池或在BHT處於工作狀態時充電等情況 下,建議使用電源供應器,因為這些情況可能會導致長時間充電或充電錯誤。使用耗損的電池可能會導 致充電錯誤。在這種情況下,要更換新的電池。 26
4.1 開啟電源 電源開啟 要開啟BHT的電源,請按住位於機器上側的電源鍵 面,即可顯示主畫面。 。OS啟動並顯示鎖定畫面。從下往上滑動鎖定畫 注意。為了方便手持式掃描器供電,必須將電池固定在正確位置上。在冷藏室等低溫環境下使用BHT 時,請在正常環境溫度下開機,再將BHT帶到低溫環境中。在低溫下開啟BHT電源,可能無法成功啟動 BHT。由於電池的特性使然,在低溫環境下操作BHT,可能會導致BHT延遲運行或大幅縮短工作時間。 使用前請確認操作條件。 4.2 掃描條碼 按照以下步驟讀取條碼。 4.2.1 按下電源鍵,從睡眠狀態啟動BHT。 4.2.
4.2.3 將條碼讀取窗口指向要掃描的條碼,並按下掃描器側面的觸發鍵。 用掃描用的光線進行照射,對列印出來的條碼進行掃描。 成功掃描並顯示資料後,或是經過一段時間後,掃描的燈光會消 失。 藍色發光 4.3 Turn OFF the Power Power OFF 要關閉BHT電源,按住電源按鈕 ,點選彈出的 ★電源關閉★功能表。在點選 ★關閉電源★ 功能表 之前,請確認所有的用戶資料和工作都已儲存。 4.4 電池電量指示燈 可從液晶螢幕右上方顯示的電池圖示確認主電池的電量。由於指示燈顯示的只是主電池電量的粗略估 計,並非準確的剩餘電量,所以請儘早充電。 主電池電量指示燈只顯示電池電量的粗略估計,並非準確的剩餘電量。請閱讀安全注意事項,確保已正 確使用電池。 電池圖示 狀態 100% 100% 76% 略微減少 15% 降至15%以下 充電 4.
對策 原因 當光線從正上方聚焦在條碼的印刷表面時, BHT可能會因鏡面反射而無法讀取條碼。 改變BHT讀取角度,再試一次。 如果條碼離BHT讀取窗口太近或太遠,即使 條碼在讀取區域內,也可能無法讀取。 緩慢地將BHT移向或遠離條碼,然後 再試一次。 如果其表面極度彎曲,可能無法讀取條碼。 如果條碼表面有汙垢,可能無法讀取。 讀取位於條碼讀取窗口中心位置的條 碼。 抹除條碼上的污垢,再試一次。 如果條碼讀取窗口有汙垢,可能無法讀取條 碼。 用氣刷吹走所有灰塵,然後用棉籤或 類似的軟物輕輕擦拭讀取窗口。 陽光直射或周圍光線的亮度可能會對條碼讀 取產生不利影響。 讀取條碼時要避開陽光直射。在室內 讀取時,調整周圍光線的亮度。 鏡面反射 與條碼之距離 條碼表面曲率 條碼表面的汙垢 條碼讀取窗口的 汙垢 陽光直射、 環境光線 29
6.1 BHT電源沒有開啟 ・ 確認主電池已正確插入BHT中。 ・ 檢查電池電量,必要時為電池充電。 ・ 抹除主電池和BHT掃描器上的灰塵。 6.2 BHT無法充電。 ・ 確認已使用專用電源供應器。 ・ 確認主電池已正確插入BHT中。 ・ 確認BHT已被正確放置在充電座中。 當正確放入充電座時,BHT狀態指示燈將變成紅色。 ・ 抹除主電池和BHT掃描器上的灰塵。 ・ 如果主電池充電次數超過300次,或使用時間超過一年,請更換新的電池,以避免因電池劣化而造 成的任何問題。 6.
保留所有權利。未經出版商書面許可,不得以任何形式或手段複製本出版物的任何部分。所有提 及的產品和公司名稱均為其各自持有者所擁有的商標或註冊商標。 DENSO WAVE INCORPORATED不承擔因應用或使用本文所述的任何產品、電路或應用程式而 產生的或與之相關的任何產品責任。 如果DENSO WAVE INCORPORATED判斷是由於產品掉落或受到撞擊而導致的故障,即使在保 固期內,也會收取合理的維修費用。 智慧財產權注意事項 DENSO WAVE INCORPORATED(以下簡稱「DENSO WAVE」 )採取合理的預防措施,確保其 產品不侵犯他人的任何專利或其他任何智慧財產權,但DENSO WAVE對以下狀況的任何專利或其 他智慧財產權之侵權或違法行為概不負責: (i)將DENSO WAVE的產品與非DENSO WAVE提供 的其他元件、產品、資料處理系統或裝置或軟體連接或結合使用; (ii)使用DENSO WAVE產品的 方式不符合此產品的用途或設計;或是(iii)由DENSO WAVE以外的他者對 DENSO WAVE產品 所進行的任何改裝。 版權所有 © DE