BHT-1200 Series Operator’s Guide 2D Code Handy Terminal BHT-1281QULWB-CE Thank you for using the DENSO WAVE 2D Code Handy Terminal. Please read this manual thoroughly prior to operation to ensure full use of the product’s functionality, and store safely in a convenient location for quick reference even after reading. This manual contains only the basic details required for operation. Please refer to the User’s Manual for further details on general operation.
Some of the pixels on the LCD touch screen may not illuminate or stay permanently illuminated. Furthermore, there may also be inconsistencies in color and brightness. None of these aspects represent an LCD defect. A thin Newton’s ring (rainbow-like patterns) may appear on the touch panel. This does not necessarily indicate a problem with the touch panel. About This Manual Due to changes and improvements, the content of this manual may be subject to change without prior notice.
Usage Precautions Usage environment restrictions Do not use the BHT where it may be exposed to fire, high temperatures, or direct sunlight. (Failure to observe this may result in damage, overheating, explosion, or fire.) * When the BHT is stored in a high-temperature, high-humidity environment of 50 to 60C, leave to sit in a location at room temperature and normal humidity for at least 1 day prior to use. Failure to observe this may cause a reading failure or damage the BHT.
SAFETY PRECAUTIONS Be sure to observe all these safety precautions. WARNING CAUTION Meaning of Symbols Alerts you to those conditions which could cause serious bodily injury or death if the instructions are not followed correctly. Alerts you to those conditions which could cause minor bodily injury or substantial property damage if the instructions are not followed correctly.
To System Designers: When introducing BHT in those systems that could affect human lives (e.g., medicines management system), develop applications carefully through redundancy and safety design which avoids the feasibility of affecting human lives even if a data error occurs. Handling the BHT Incorrect handling of the BHT could cause electric shock, impaired vision, skin problems, injury, burns and generation of heat and smoke from the BHT. Be sure to observe the following to use the device correctly.
The 2D Code Handy Terminal uses a laser light for indicating the scanning range. The intensity of the laser light is too low to inflict bodily injury. However, do not stare into beam. You must observe the following precautions when handling the BHT equipped with laser light. 1) Never stare into the reading window. 2) Never point the reading window at someone’s eye. The 2D Code Handy Terminal complies with IEC 60825-1 Ed. 2: 2007.
Wireless Equipment ●Precautions relating to the frequency used by this device In addition to industrial, scientific, and medical equipment such as microwave ovens, static wireless stations (permit required) used for mobile identification in places such as plant manufacturing lines and specified low-power wireless stations (no permit required) operate on the same frequency band as this device. 1.
Components and Functions BHT-1281QULWB-CE Indicator LED When succeeding in the reading of the barcode, illuminates in blue.Illuminates in red during charging, and turns green on completion of charging. LCD (with Touch panel) Display characters and graphic patterns. Data may be entered by tapping the screen directly with the stylus. Trigger Key Trigger Key Interface port BHT charge terminals and Interface terminals Battery cover RFID antenna Reading window Battery cover Trigger Key Speaker IEEE802.
Key pad The BHT key functions can be set at user programs. The diagram below shows an example of settings for each key function.
No. Key ① + ② ③ Name Function and Description Tab key Used to enter a tab character. M1, M2, M3 magic keys ・The SF and ENT key functions can be assigned to these magic keys by making settings at the SYSTEM MENU. ・Character strings can be assigned at user programs. * Refer to the User’s Manual for details on how to operate the SYSTEM MENU. + ④ ⑤ ⑥ Trigger keys Press to scan codes and RF tags. (This key performs the same function as the Scan key.) ⑦ Backspace key Moves back one character.
Input Method Using the Stylus The BHT liquid crystal display (LCD) is a touch screen. Buttons, menus and so displayed on the screen can be selected using the stylus provided. Touch Screen Operation Select the LCD touch screen buttons and menus and so on using the stylus provided. Action Description Tap This involves tapping the touch screen once. This function is the equivalent of a “click” with a mouse on a computer. Double-tap This involves tapping the touch screen twice in quick succession.
Proper Care of the BHT Make sure to turn OFF the BHT before cleaning. ● Terminal dirt on the BHT and battery Periodically wipe any dirt from the terminals of the BHT and battery with a cotton swab or similar soft object. The terminal should be treated with the utmost care so as not to be scratched or bent during a cleaning. Never use organic solvents such as benzene or alcohol, as this may cause the coated surface to come off. ● Housing dirt Wipe any dirt from the housing with a dry, soft cloth.
Step 1 Charging The battery is not charged when purchased and must therefore be charged prior to use. The following Cradle can be used with the BHT. Cradle: CU-1211, CU-1233 It takes about 9 hours to charge the batteries (when both the batteries in the BHT main body and in the grip are mounted). ・It takes about 4.5 hours when the battery is mounted only in the BHT main body. ・If a battery of which discharge amount is small is used, it takes less time to complete charging.
Caution when Installing the BHT to the CU ・Place the BHT on the CU carefully. Insert the BHT along the guides at the both sides of the CU. ・If the BHT does not fit into the guides smoothly, take it off and confirm that there is no foreign object which blocks the insertion. Then, insert the BHT again. Be sure not to install the BHT forcedly. When the red LED of the BHT is blinking, the conceivable causes are as follows. Take an appropriate action. ・The battery of the BHT main body is not mounted.
Step 2 Turning ON the Power It is necessary to perform touch screen calibration and set the date and time when turning ON the BHT power for the first time. Press the power key to turn ON the BHT power. The calibration screen should then display. If the calibration screen does not display, first perform a “full reset.” Refer to “Resetting and Full Resetting” for details of the full reset method. Press the power key to turn ON the BHT power.
Turning the Power OFF Use one of the following three methods to turn OFF the BHT power. (1) Normal power OFF Press the power key. The BHT power turns OFF after the message right displays. Point Do not remove the battery while the message on the right is displayed. Failure to observe this may result in data stored in the BHT being lost. (2) Turning the power OFF after registry back-up Hold down the SF key and press the power key. The message right displays and registry back-up is commenced.
Reading/Writing RF Tags Read and write RF tags in accordance with the procedures given below. 1 Press the power key BHT power ON. to turn the Power Key 2 Select System Properties of BhtShell from the Desktop menu to activate RFID Menu. Select TAG READ and Start in RFID Menu in this order. The red LED is turned ON. Red is ON. RF tag Point The continuous read mode is set at the time of factory shipment. You can change the read mode in the Read Mode menu.
Distance from an RF tag If the BHT is used near other radio devices such as a personal radio station or an amateur radio station, it may not be able to read/write RF tags. If the distance from an RF tag is too close or too far, the BHT may not be able to read/write it. The writable distance may be shorter than the readable distance. Do not use the BHT used near other radio devices such as a personal radio station or an amateur radio station.
When Unable to Successfully Read Codes Cause Countermeasure Change the BHT scanning angle and try again. Specular reflection When the light is focused on the printed surface of the code from directly above, the BHT may not read the code due to specular reflection. Distance from code Scanning may be unsuccessful if it is too close to or too far from the BHT reading window, even when the code is within the read area. Move the BHT slowly toward or away from the code and try again.
Replacing the Batteries 1 Press the power key to turn OFF the BHT power. The screen on the right displays. Point Do not remove the battery until the power turns OFF and the screen display clears. 2 Shutdown In progress Do not remove The battery. Replacement of the battery in the main body Slide the battery cover lock as pushing it and remove the battery cover. 3 Remove the battery.
5 Close the battery cover and restore the battery cover lock to the original position. 6 Replacement of the battery in the grip Slide the battery cover lock as pushing it and remove the battery cover. 7 Remove the battery.
8 9 Check the protrusions of a new battery and mount the battery in the arrow direction. Close the battery cover, and restore the battery cover lock to the original position as pushing it.
Using the BHT after Long Non-Use Data stored in the BHT may be lost or damaged and the calendar clock may stop if the BHT is left unused for a long period of time. ・Keep a backup copy of important or critical information. ・Reset the calendar clock if it is stopped. ・The battery is also used as a backup power source. You should not remove the battery from the BHT for at least 2 days until memory backup power is fully charged. Please refer to the User’s Manual for more information on trouble shooting.
Turning ON/OFF the Backlight To turn the backlight ON or OFF, hold down the Shift key and press the M3 Key. Backlight OFF or dim (backlight function enabled) If no key is pressed for 3 seconds.* 1 2 4 5 6 7 8 9 . 0 Hold down the Shift key and press the M3 Key. Press any key or tap the touch screen. 3 Backlight ON Shift key M3 key Hold down the Shift key and press the M3 Key. Hold down the Shift key and press the M3 Key.
Resetting and Full Resetting Reset Reset the BHT in the following cases. The BHT makes no response to entry from the touch screen or keys. Programs in the BHT malfunction for some unknown reason. Reset Method With the BHT power ON, press the reset key combination (BKSP + Right Trigger + Power). Then release all keys. Point Data stored as a file will not be lost even after resetting. However, any data currently being edited will be lost.
Memory Contents after Reset/Full Reset Reset Full Reset Data retained Data retained Data in the “Storage Card” folder (microSD Card) Data retained Data retained Data in other folders Data retained Data erased Contents of the Registry Data retained Data erased Data being edited Data erased Data erased Data in the “FLASH” folder (on-board FLASH memory) (Note) If the Registry has been backed up the backed up Registry will be used.
FCC Regulation (for United States America) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
FCC/IC Radiation Exposure Statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used.
1, Yoshiike, Kusagi, Agui-cho, Chita-gun, Aichi 470-2297, Japan http://www.denso-wave.com/ This manual uses recycled paper. 본 인쇄물은 재생지를 활용합니다.