BHT-1200 Series Operator’s Guide 조작 가이드 操作手冊 2D Code Handy Terminal BHT-1261QWBG-CE Thank you for using the DENSO WAVE 2D Code Handy Terminal. Please read this manual thoroughly prior to operation to ensure full use of the product’s functionality, and store safely in a convenient location for quick reference even after reading. This manual contains only the basic details required for operation. Please refer to the User’s Manual for further details on general operation.
Some of the pixels on the LCD touch screen may not illuminate or stay permanently illuminated. Furthermore, there may also be inconsistencies in color and brightness. None of these aspects represent an LCD defect. A thin Newton’s ring (rainbow-like patterns) may appear on the touch panel. This does not necessarily indicate a problem with the touch panel. About This Manual Due to changes and improvements, the content of this manual may be subject to change without prior notice.
Usage Precautions Usage environment restrictions Do not use the BHT where it may be exposed to fire, high temperatures, or direct sunlight. (Failure to observe this may result in damage, overheating, explosion, or fire.) * When the BHT is stored in a high-temperature, high-humidity environment of 50 to 60C, leave to sit in a location at room temperature and normal humidity for at least 1 day prior to use. Failure to observe this may cause a reading failure or damage the BHT.
SAFETY PRECAUTIONS Be sure to observe all these safety precautions. WARNING CAUTION Meaning of Symbols Alerts you to those conditions which could cause serious bodily injury or death if the instructions are not followed correctly. Alerts you to those conditions which could cause minor bodily injury or substantial property damage if the instructions are not followed correctly.
To System Designers: When introducing BHT in those systems that could affect human lives (e.g., medicines management system), develop applications carefully through redundancy and safety design which avoids the feasibility of affecting human lives even if a data error occurs. Handling the BHT Incorrect handling of the BHT could cause electric shock, impaired vision, skin problems, injury, burns and generation of heat and smoke from the BHT. Be sure to observe the following to use the device correctly.
The 2D Code Handy Terminal uses a laser light for indicating the scanning range. The intensity of the laser light is too low to inflict bodily injury. However, do not stare into beam. You must observe the following precautions when handling the BHT equipped with laser light. 1) Never stare into the reading window. 2) Never point the reading window at someone’s eye. The 2D Code Handy Terminal complies with IEC 60825-1 Ed. 2: 2007.
Wireless Equipment ●Precautions relating to the frequency used by this device In addition to industrial, scientific, and medical equipment such as microwave ovens, static wireless stations (permit required) used for mobile identification in places such as plant manufacturing lines and specified low-power wireless stations (no permit required) operate on the same frequency band as this device. 1.
Components and Functions BHT-1261QWBG-CE GPS built-in antenna* Indicator LED When succeeding in the reading of the barcode, illuminates in blue.Illuminates in red during charging, and turns green on completion of charging. Receiver LCD (with Touch panel) Display characters and graphic patterns. Data may be entered by tapping the screen directly with the stylus.
Key pad The BHT key functions can be set at user programs. The diagram below shows an example of settings for each key function.
No. Key ① + ② ③ Name Function and Description Tab key Used to enter a tab character. M1, M2, M3 magic keys ・The SF and ENT key functions can be assigned to these magic keys by making settings at the SYSTEM MENU. ・Character strings can be assigned at user programs. * Refer to the User’s Manual for details on how to operate the SYSTEM MENU. + ④ ⑤ ⑥ Trigger keys Press to scan codes. (This key performs the same function as the Scan key.) ⑦ Backspace key Moves back one character.
Input Method Using the Stylus The BHT liquid crystal display (LCD) is a touch screen. Buttons, menus and so displayed on the screen can be selected using the stylus provided. Touch Screen Operation Select the LCD touch screen buttons and menus and so on using the stylus provided. Action Description Tap This involves tapping the touch screen once. This function is the equivalent of a “click” with a mouse on a computer. Double-tap This involves tapping the touch screen twice in quick succession.
Proper Care of the BHT Make sure to turn OFF the BHT before cleaning. ● Terminal dirt on the BHT and battery Periodically wipe any dirt from the terminals of the BHT and battery with a cotton swab or similar soft object. The terminal should be treated with the utmost care so as not to be scratched or bent during a cleaning. Never use organic solvents such as benzene or alcohol, as this may cause the coated surface to come off. ● Housing dirt Wipe any dirt from the housing with a dry, soft cloth.
Step 1 Charging The battery is not charged when purchased and must therefore be charged prior to use. The following Cradle can be used with the BHT. Cradle: CU-1211, CU-1233 The charge time is approximately 3 hours (standard rechargeable battery) or 4.5 hours (large-capacity rechargeable battery). • An almost completely discharged battery should take this time to become fully charged. ■Charging with the BHT Place the BHT on the Cradle.* The LED illuminates in red and charging begins.
Step 2 Attaching stylus Attach the stylus to the hand belt to prevent it from being lost. Attach the hand strap to prevent from dropping the BHT accidentally. Attachment Attach the stylus as shown below. Holding the BHT Insert your hand into the hand belt and hold the BHT as shown below.
Step 3 Turning ON the Power It is necessary to perform touch screen calibration and set the date and time when turning ON the BHT power for the first time. Press the power key to turn ON the BHT power. The calibration screen should then display. If the calibration screen does not display, first perform a “full reset.” Refer to “Resetting and Full Resetting” for details of the full reset method. Press the power key to turn ON the BHT power.
Turning the Power OFF Use one of the following three methods to turn OFF the BHT power. (1) Normal power OFF Press the power key. The BHT power turns OFF after the message right displays. Point Do not remove the battery while the message on the right is displayed. Failure to observe this may result in data stored in the BHT being lost. (2) Turning the power OFF after registry back-up Hold down the SF key and press the power key. The message right displays and registry back-up is commenced.
Scanning codes Follow the procedure below to scan codes. 1 Turn the BHT power ON. Power key 2 Select code scanning test of BhtShell from desktop menu. Press the trigger key. The BHT emits an illumination LED. Illumination light 3 Hold the BHT close to the code to align the illumination LED. Blue LED When the BHT has read the code successfully, the indicator LED will illuminate in blue. Codes can be read also by pressing the Scan key.
When Unable to Successfully Read Codes Cause Countermeasure Change the BHT scanning angle and try again. Specular reflection When the light is focused on the printed surface of the code from directly above, the BHT may not read the code due to specular reflection. Distance from code Scanning may be unsuccessful if it is too close to or too far from the BHT reading window, even when the code is within the read area. Move the BHT slowly toward or away from the code and try again.
How to Replace the Battery 1 Press the power key to turn OFF the BHT power. The screen on the right displays. Point Do not remove the battery until the power turns OFF and the screen display clears. 2 3 4 Loosen the hand belt. Press and slide the battery cover lock to remove the Battery cover. Remove the battery.
5 Load the battery in the direction shown by the arrow. Terminal Battery pull tape (2cell battery only) 6 Close the battery cover and return the battery cover lock to the original position. Point The end of the battery pull tape must not come out of the edge under the battery cover. 7 Return the hand belt to its original position.
Using the BHT after Long Non-Use Data stored in the BHT may be lost or damaged and the calendar clock may stop if the BHT is left unused for a long period of time. ・Keep a backup copy of important or critical information. ・Reset the calendar clock if it is stopped. ・The battery is also used as a backup power source. You should not remove the battery from the BHT for at least 2 days until memory backup power is fully charged. Please refer to the User’s Manual for more information on trouble shooting.
Turning ON/OFF the Backlight To turn the backlight ON or OFF, hold down the Shift key and press the M3 Key. Backlight OFF or dim (backlight function enabled) If no key is pressed for 3 seconds.* 1 2 4 5 6 7 8 9 . 0 Hold down the Shift key and press the M3 Key. Press any key or tap the touch screen. 3 Backlight ON Shift key M3 key Hold down the Shift key and press the M3 Key. Hold down the Shift key and press the M3 Key.
Resetting and Full Resetting Reset Reset the BHT in the following cases. The BHT makes no response to entry from the touch screen or keys. Programs in the BHT malfunction for some unknown reason. Reset Method With the BHT power ON, press the reset key combination (BKSP + Right Trigger + Power). Then release all keys. Point Data stored as a file will not be lost even after resetting. However, any data currently being edited will be lost.
Memory Contents after Reset/Full Reset Reset Full Reset Data retained Data retained Data in the “Storage Card” folder (microSD Card) Data retained Data retained Data in other folders Data retained Data erased Contents of the Registry Data retained Data erased Data being edited Data erased Data erased Data in the “FLASH” folder (on-board FLASH memory) (Note) If the Registry has been backed up the backed up Registry will be used.
Declaration of Conformity English: Hereby, DENSO WAVE INCORPORATED declares that the device BHT-1261QWBG-CE is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Български: С настоящето DENSO WAVE INCORPORATED декларира, че устройството BHT-1261QWBG-CE съответства на съществените изисквания и другите приложими разпоредби на Директива 1999/5/EО.
Slovensky: Spoločnosť DENSO WAVE INCORPORATED týmto vyhlasuje, že zariadenie BHT-1261QWBG-CE je v súlade so základnými požiadavkami a ostatnými príslušnými ustanoveniami Smernice 1999/5/ES. Slovenščina: Podjetje DENSO WAVE INCORPORATED izjavlja, da je naprava BHT-1261QWBG-CE skladna z bistvenimi zahtevami in drugimi relevantnimi določili direktive 1999/5/ES.
IC Regulation (for Canada) CAN ICES-3 (B)/NMB-3(B) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
NCC Regulation (for Taiwan) 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或 變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善 至無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Battery Recycling Request This product uses a lithium-ion battery that contains scarce, valuable recyclable resources. We kindly ask for your cooperation in recycling to promote reuse of these resources. EU The crossed-out wheeled bin is applicable for EU member status only.
F FCC Regulation (for United States America) General This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.
1, Yoshiike, Kusagi, Agui-cho, Chita-gun, Aichi 470-2297, Japan http://www.denso-wave.com/ This manual uses recycled paper. 본 인쇄물은 재생지를 활용합니다.