BHT-1200 Series Operator’s Guide 조작 가이드 操作手冊 Barcode Handy Terminal BHT-1261BWB-CE 2D Code Handy Terminal BHT-1261QWB-CE Thank you for using the DENSO WAVE Barcode Handy Terminal/2D Code Handy Terminal. Please read this manual thoroughly prior to operation to ensure full use of the product’s functionality, and store safely in a convenient location for quick reference even after reading. This manual contains only the basic details required for operation.
Some of the pixels on the LCD touch screen may not illuminate or stay permanently illuminated. Furthermore, there may also be inconsistencies in color and brightness. None of these aspects represent an LCD defect. A thin Newton’s ring (rainbow-like patterns) may appear on the touch panel. This does not necessarily indicate a problem with the touch panel. About This Manual Due to changes and improvements, the content of this manual may be subject to change without prior notice.
Usage Precautions Usage environment restrictions Do not use the BHT where it may be exposed to fire, high temperatures, or direct sunlight. (Failure to observe this may result in damage, overheating, explosion, or fire.) * When the BHT is stored in a high-temperature, high-humidity environment of 50 to 60C, leave to sit in a location at room temperature and normal humidity for at least 1 day prior to use. Failure to observe this may cause a reading failure or damage the BHT.
SAFETY PRECAUTIONS Be sure to observe all these safety precautions. Meaning of Symbols WARNING Alerts you to those conditions which could cause serious bodily injury or death if the instructions are not followed correctly. CAUTION Alerts you to those conditions which could cause minor bodily injury or substantial property damage if the instructions are not followed correctly.
Handling the BHT Incorrect handling of the BHT could cause electric shock, impaired vision, skin problems, injury, burns and generation of heat and smoke from the BHT. Be sure to observe the following to use the device correctly. Never put the BHT into a microwave oven or high-pressure container. Doing so could cause the BHT to break, generate heat, rupture or burn.
Wireless Equipment ●Precautions relating to the frequency used by this device In addition to industrial, scientific, and medical equipment such as microwave ovens, static wireless stations (permit required) used for mobile identification in places such as plant manufacturing lines and specified low-power wireless stations (no permit required) operate on the same frequency band as this device. 1.
Components and Functions BHT-1261BWB-CE IEEE802.11b/g/n 2.4GHz built-in antenna* Bluetooth® built-in antenna* Indicator LED When succeeding in the reading of the barcode, illuminates in blue. Illuminates in red during charging, and turns green on completion of charging. Receiver IEEE802.11a 5GHz built-in antenna* LCD (with Touch panel) Display characters and graphic patterns. Data may be entered by tapping the screen directly with the stylus.
Components and Functions BHT-1261QWB-CE IEEE802.11b/g/n 2.4GHz built-in antenna* Bluetooth® built-in antenna* Indicator LED When succeeding in the reading of the barcode, illuminates in blue. Illuminates in red during charging, and turns green on completion of charging. Receiver IEEE802.11a 5GHz built-in antenna* LCD (with Touch panel) Display characters and graphic patterns. Data may be entered by tapping the screen directly with the stylus.
Key pad The BHT key functions can be set at user programs. The diagram below shows an example of settings for each key function. 1 2 3 4 5 6 8 7 9 10 11 17 18 1 2 3 4 5 6 7 8 9 .
No. Key ① + ② ⑤ Name Function and Description Tab key Used to enter a tab character. M1, M2, M3 magic keys ・The SF and ENT key functions can be assigned to these magic keys by making settings at the SYSTEM MENU. ・Character strings can be assigned at user programs. * Refer to the User’s Manual for details on how to operate the SYSTEM MENU. + ⑥ ③ ④ Trigger keys Press to scan codes. (This key performs the same function as the Scan key.) ⑦ Backspace key Moves back one character.
Input Method Using the Stylus The BHT liquid crystal display (LCD) is a touch screen. Buttons, menus and so displayed on the screen can be selected using the stylus provided. Touch Screen Operation Select the LCD touch screen buttons and menus and so on using the stylus provided. Action Description Tap This involves tapping the touch screen once. This function is the equivalent of a “click” with a mouse on a computer. Double-tap This involves tapping the touch screen twice in quick succession.
Proper Care of the BHT Make sure to turn OFF the BHT before cleaning. ● Terminal dirt on the BHT and battery Periodically wipe any dirt from the terminals of the BHT and battery with a cotton swab or similar soft object. The terminal should be treated with the utmost care so as not to be scratched or bent during a cleaning. Never use organic solvents such as benzene or alcohol, as this may cause the coated surface to come off. ● Housing dirt Wipe any dirt from the housing with a dry, soft cloth.
Step 1 Charging The battery is not charged when purchased and must therefore be charged prior to use. The following Cradle can be used with the BHT. Cradle: CU-1211, CU-1233 The charge time is approximately 3 hours (standard rechargeable battery) or 4.5 hours (large-capacity rechargeable battery). • An almost completely discharged battery should take this time to become fully charged. ■Charging with the BHT Place the BHT on the Cradle.* The LED illuminates in red and charging begins.
Step 2 Attaching stylus Attach the stylus to the hand belt to prevent it from being lost. Attach the hand strap to prevent from dropping the BHT accidentally. Attachment Attach the stylus as shown below. Holding the BHT Insert your hand into the hand belt and hold the BHT as shown below.
Step 3 Turning ON the Power It is necessary to perform touch screen calibration and set the date and time when turning ON the BHT power for the first time. Press the power key to turn ON the BHT power. The calibration screen should then display. If the calibration screen does not display, first perform a “full reset.” Refer to “Resetting and Full Resetting” for details of the full reset method. Press the power key to turn ON the BHT power.
Turning the Power OFF Use one of the following three methods to turn OFF the BHT power. (1) Normal power OFF Press the power key. The BHT power turns OFF after the message right displays. Point Do not remove the battery while the message on the right is displayed. Failure to observe this may result in data stored in the BHT being lost. (2) Turning the power OFF after registry back-up Hold down the SF key and press the power key. The message right displays and registry back-up is commenced.
Scanning codes Follow the procedure below to scan codes. 1 Turn the BHT power ON. Power key 2 Select code scanning test of BhtShell from desktop menu. BHT-1261QWB-CE BHT-1261BWB-CE Press the trigger key. The BHT emits an illumination LED. Illumination light Illumination light 照明光 照明光 3 Hold the BHT close to the code to align the BHT-1261BWB-CE illumination LED. When the BHT has read the code successfully, the indicator LED will illuminate in blue.
When Unable to Successfully Read Codes Cause When the light is focused on the printed surface of the code from directly above, the BHT may not read the code due to specular reflection. Countermeasure Change the BHT scanning angle and try again.
How to Replace the Battery 1 Press the power key to turn OFF the BHT power. The screen on the right displays. Point Do not remove the battery until the power turns OFF and the screen display clears. 2 3 4 Loosen the hand belt. Press and slide the battery cover lock to remove the Battery cover. Remove the battery.
5 Load the battery in the direction shown by the arrow. Terminal Battery pull tape (2cell battery only) 6 Close the battery cover and return the battery cover lock to the original position. Point The end of the battery pull tape must not come out of the edge under the battery cover. 7 Return the hand belt to its original position.
Using the BHT after Long Non-Use Data stored in the BHT may be lost or damaged and the calendar clock may stop if the BHT is left unused for a long period of time. ・Keep a backup copy of important or critical information. ・Reset the calendar clock if it is stopped. ・The battery is also used as a backup power source. You should not remove the battery from the BHT for at least 2 days until memory backup power is fully charged. Please refer to the User’s Manual for more information on trouble shooting.
Turning ON/OFF the Backlight To turn the backlight ON or OFF, hold down the Shift key and press the M3 Key. Backlight OFF or dim (backlight function enabled) If no key is pressed for 3 seconds.* 1 2 4 5 6 7 8 9 . 0 Hold down the Shift key and press the M3 Key. Press any key or tap the touch screen. 3 Backlight ON Shift key M3 key Hold down the Shift key and press the M3 Key. Hold down the Shift key and press the M3 Key.
Resetting and Full Resetting Reset Reset the BHT in the following cases. The BHT makes no response to entry from the touch screen or keys. Programs in the BHT malfunction for some unknown reason. Reset Method With the BHT power ON, press the reset key combination (BKSP + Right Trigger + Power). Then release all keys. Point Data stored as a file will not be lost even after resetting. However, any data currently being edited will be lost.
Memory Contents after Reset/Full Reset Reset Full Reset Data retained Data retained Data in the “Storage Card” folder (microSD Card) Data retained Data retained Data in other folders Data retained Data erased Contents of the Registry Data retained Data erased (Note) Data being edited Data erased Data erased Data in the “FLASH” folder (on-board FLASH memory) (Note) If the Registry has been backed up the backed up Registry will be used.
Declaration of Conformity(only Wireless LAN model / Bluetooth® model) English: Hereby, DENSO WAVE INCORPORATED, declares that this BHT-1261BWB that are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Česky: Firma DENSO WAVE INCORPORATED tímto prohlašuje, že její radio- a telekomunikační terminál BHT-1261BWB které vyplňují základní požadavky a další příslušná ustanovení směrnice 1999/5/ES.
Norsk: DENSO WAVE INCORPORATED erklæ rer med dette at denne BHT-1261BWB som er i samsvar med regelverk og ø vrige bestemmelser i direktiv 1999/5/EC. CE marking For Australia and New Zealand This BHT-1261BWB contains Wireless LAN Module (type:WLS5001B).
Applicable Countries(for European Union/only Wireless LAN model) Applicable countries This product can be used in the following countries: Finland, Estonia, Iceland, Ireland, United Kingdom, Italy*, Austria, Netherlands, Cyprus, Greece, Switzerland, Sweden, Spain, Slovakia, Slovenia, Czech Republic, Denmark, Germany, Norway, Hungary, France**, Bulgaria, Belgium, Poland, Portugal, Latvia, Lithuania, Romania, Turkey, Croatia, Macedonia For use in any other country, please consult with your dealer.
FCC Regulation (for United States America) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IC Regulation (for Canada) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IDA Regulation (for Singapore) IDA Compliance Marking Complies with IDA Standards DB104459 인증 표시 KCC Regulation(for Korea) B 급 기기 (가정용 방송통신기자재) 이 기기는 가정용(B 급) 전자파적합기기로서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. 해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다.
Battery Recycling Request This product uses a lithium-ion battery that contains scarce, valuable recyclable resources. We kindly ask for your cooperation in recycling to promote reuse of these resources. The crossed-out wheeled bin is applicable for EU member status only. Used batteries must not be disposed of as combustibles. Contact your nearest local sales office for information on disposal procedures.
1, Yoshiike, Kusagi, Agui-cho, Chita-gun, Aichi 470-2297, Japan http://www.denso-wave.com/ This manual uses recycled paper. 본 인쇄물은 재생지를 활용합니다.