User's Manual

ManualsBrandsDENSO TEN ManualsElectronicsCD Receiver with Bluetooth

• Do not leave your mobile phone in the car. The temperature inside may

be high and damage the phone.

• When you dispose of your car, take care to delete all personal data that

are registered in your ISUZU D-MAX AUDIO system. You should delete

the following Hands-free data from the system;

• Bluetooth phone data

In the following conditions, the system may not function.

• The mobile phone is turned off.

• The current position is outside the communication area.

• The mobile phone is not connected.

• The mobile phone has a low battery.

HANDS-FREE SYSTEM

• The Bluetooth

word mark and logos are owned by the Bluetooth

Hands-free system allows you to make or receive a call without taking

SIG, Inc. and use of such marks by ISUZU MOTORS LIMITED is

your hands off the steering wheel by connecting your mobile phone.

under license. Other trade marks and trade names are those of their

This system supports Bluetooth. Bluetooth is a wireless radio data

respective owners.

transferring system by which you can make calls without your mobile

• Compatible Bluetooth Specifications: Bluetooth Specification Ver. 1.2

phone being connected with a cable or placed on cable.

or later

If your mobile phone does not support Bluetooth, this system

• Compatible Profiles: HFP Ver. 1.5 or later

can not function.

OPP Ver. 1.1 or later

ATTENTION

NOTE

CAUTION

While driving, do not use a mobile phone or connect the bluetooth phone.

HANDS-FREE OPERATION

③ DISPLAY WINDOW

⑦ FUNCTION

BUTTONS

① VOLUME

ADJUST

KNOB

② PHONE

BUTTON

⑤ AUDIO

BUTTON

④ TUNE•

FILE

KNOB

⑥ MENU

BUTTON

FUJITSU TEN CONFIDENTIAL

Summary of content (6 pages)

PAGE 1
HANDS-FREE OPERATION ATTENTION ③ DISPLAY WINDOW • Do not leave your mobile phone in the car. The temperature inside may be high and damage the phone. • When you dispose of your car, take care to delete all personal data that are registered in your ISUZU D-MAX AUDIO system.
PAGE 2
ABOUT THE DISPLAY • The telephone set will be registered in the main unit automatically. When registration is completed, the message "Completed!" appear for a few seconds Reception Level Indication The strength of the reception is indicated in the DISPLAY WINDOW ③ and " " is shown in the DISPLAY WINDOW ③ in that order. (5) Press the PHONE button ② to go back to the previous mode.
PAGE 3
ATTENTION You cannot change the pass key while driving. Park your vehicle in a secure location and change the pass key. (1) Press the PHONE BUTTON ② to display the phone menu. (2) Press DIAL in the FUNCTION BUTTON ⑦ to input the number you wish to call. (3) Turn the TUNE•FILE KNOB ④ to display the numeral of your choice in the DISPLAY WINDOW ③, then press the AUDIO BUTTON ⑤. • Repeat the same operation until you have entered the entire number.
PAGE 4
ANSWERING A PHONE CALL When your telephone set receives a call, the name or telephone number appears in the DISPLAY WINDOW ③ • If the incoming telephone number is not registered, the telephone number is displayed in the DISPLAY WINDOW ③. If the incoming telephone name and number are registered, the name is displayed in the DISPLAY WiNDOW ③. If only the incoming telephone number is registered, the telephone number is displayed in the DISPLAY WINDOW ③.
PAGE 5
(3) Press BOOK in the FUNCTION BUTTON ⑦ to display all registered phone number. (4) Turn the TUNE•FILE KNOB ④ to search for the phone book entry you wish to delete. (5) Press DEL in the FUNCTION BUTTON ⑦ to delete the registered phone number. SETTING THE VOLUME SETTING THE SPEECH VOLUME (1) Turn the VOLUME ADJUST KNOB ① clockwise or anticlockwise to achieve the speech volume you consider best. •The volume set in the adjustment is recorded.
PAGE 6
FCC ID: BABFT0018A This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.