Denon AVR control protocol Ver.03 Application model : AVR-X3000 Application terminal: Ethernet RS-232C Rev 10.2.0 Version 01 02 03 Date 12.Mar.’13 25.April.’13 21.May.
Connector specification .
RJ-45(10BASE-T/100BASE-TX) .
NETWORK SETUP of AVR-X3000 >Procedure of Network Setup mode. (1)Press SETUP MENU button, then Menu appears on FL-display(and GUI) (2)Select “Setup Menu > Network > Settings ” . (3)Set parameters described below. "On"---Use this setting when DHCP server is on the local network. "Off"---Use this setting when DHCP server is not on the local network. When sets "Off”, please set IP address. When sets "On”, you can confirm the IP address that is set by server.
Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT.
The example of a command * is the meaning of 0x0D.
Others A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50".
COMMAND and PARAMETER list PARAMETER function example ON POWER ON/STANDBY change PWON STANDBY PWSTANDBY ? Return PW Status PW? MV UP MASTER VOLUME UP/DOWN , direct change to **(**dB) MVUP DOWN MVDOWN **:00 to 98 by ASCII , 80=80(0dB), 00=-0(--dB)(MIN) ** MV80 ? Return MV Status MV? CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP FL DOWN ---FRONT Lch CVFL DOWN FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50 FR UP CVFR UP FR DOWN ---FRONT Rch CVFR DOWN
PARAMETER function example SB UP CVSB UP SB DOWN ---SURROUND BACKch (SBch 1SP) CVSB DOWN SB ** **:38 to 62 by ASCII , 50=0dB CVSB 50 FHL UP CVFHL UP FHL DOWN ---FRONT HEIGHT Lch CVFHL DOWN FHL ** **:38 to 62 by ASCII , 50=0dB CVFHL 50 FHR UP CVFHR UP FHR DOWN ---FRONT HEIGHT Rch CVFHR DOWN FHR ** **:38 to 62 by ASCII , 50=0dB CVFHR 50 FWL UP CVFWL UP FWL DOWN ---FRONT WIDE Lch CVFWL DOWN FWL ** **:38 to 62 by ASCII , 50=0dB CVFWL 50 FWR UP CVFWR UP FWR DOW
COMMAND MU SI PARAMETER ON OFF ? CD TUNER DVD BD TV SAT/CBL MPLAY GAME AUX1 NET PANDORA SIRIUSXM SPOTIFY FLICKR FAVORITES IRADIO SERVER USB/IPOD USB IPD IRP FVP ? function VOLUME MUTE ON/OFF change example MUON MUOFF Return MU Status MU? SICD ---TUNER SITUNER SIDVD ---Blu-ray SIBD ---TV AUDIO SITV ---CBL/SAT SISAT/CBL SIMPLAY ---MEDIA PLAYER SIGAME ---AUX SIAUX1 ---NETWORK SINET (North America model Only) SIPANDORA (North America model Only) SISIRI
COMMAND ZM PARAMETER ON OFF ? FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY function MAIN ZONE ON/OFF change Return ZM Status FAVORITE STATION 1-3 MODE SELECT FAVORITE STATION 1-3 MODE MEMORY example ZMON ZMOFF ZM? ZMFAVORITE1 ZMFAVORITE2 ZMFAVORITE3 ZMFAVORITE1 MEMORY ZMFAVORITE2 MEMORY ZMFAVORITE3 MEMORY - 11 -
COMMAND SD DC SV SLP PARAMETER AUTO HDMI DIGITAL ANALOG ? AUTO PCM DTS ? ON OFF DVD BD TV SAT/CBL MPLAY GAME AUX1 CD ? OFF *** ? function set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) set force HDMI INPUT mode set force DIGITAL INPUT (Optical,Coaxial)mode set force ANALOG INPUT mode Return SD Status set DIGITAL INPUT AUTO mode set DIGITAL INPUT force PCM mode set DIGITAL INPUT force DTS mode Return DC Status VIDEO SELECT mode set to ON VIDEO SELECT mode cancel VIDEO SELECT mode set to ON, and select s
COMMAND MS PARAMETER MOVIE MUSIC GAME PURE DIRECT DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND MCH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE MATRIX VIDEO GAME VIRTUAL ? QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK4 MEMORY QUICK5 MEMORY QUICK ? function Select SURROUND mode ---MULTI CH STEREO mode Return MS Status QUICK SELECT 1-5 MODE SELECT QUICK SELECT 1-5 MODE MEMORY Return MSQUICK Status - 13 - example MSMOVIE MSMUSIC MSGAME MSPURE DIRECT MS
COMMAND VS PARAMETER ASPNRM ASPFUL ASP ? SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SC ? SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO SCH ? AUDIO AMP AUDIO TV AUDIO ? VPMAUTO VPMGAME VPMMOVI VPM ? function Set Aspect Ratio to 4:3 mode Set Aspect Ratio to 16:9 mode Return VSASP Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolution to 720p Set Resolution to 1080p Set Resolution to 10P24 Set Resolution to 4K Set Resolution to AUTO Return VSSC Status Set Resolution to 480p/576p (HDM
MODE: ? LOM ON LOM OFF LOM ? PHG LOW PHG MID PHG HI PHG ? function PARAMETER setting TONE CONTROL ON/OFF Return PSTONE CONTROL Status CINEMA EQ. ON/OFF example PSTONE CTRL OFF PSTONE CTRL OFF PSTONE CTRL ? PSCINEMA EQ.ON PSCINEMA EQ.OFF Return PSCINEMA EQ.Status PSCINEMA EQ. ? CINEMA / MUSIC / GAME mode change PSMODE:MUSIC (This parameter can change DOLBY PL2,PL2x, DTS NEO:X mode.
PARAMETER function example MULTEQ:AUDYSSEY MultEQ XT mode direct change PSMULTEQ:AUDYSSEY MULTEQ:BYP.LR PSMULTEQ:BYP.
PARAMETER function BAS UP BASS UP/DOWN , direct change to **dB PSBAS BAS DOWN **:00 to 99 by ASCII , 50=0dB PSBAS BAS ** ---AVR-X3000 can be operated from -6 to +6(44 to 56) PSBAS BAS ? Return PSBAS Status PSBAS TRE UP TREBLE UP/DOWN , direct change to **dB PSTRE TRE DOWN **:00 to 99 by ASCII , 50=0dB PSTRE TRE ** ---AVR-X3000 can be operated from -6 to +6(44 to 56) PSTRE TRE ? Return PSTRE Status PSTRE DRC AUTO Dynamic Compression direct change PSDRC DRC LOW PSDRC DRC MID PSDRC DRC HI PSDRC DRC OFF PSDRC D
PARAMETER function example PAN ON PANORAMA ON/OFF PSPAN ON PAN OFF PSPAN OFF PAN ? Return PSPAN Status PSPAN ? DIM UP DIMENSION UP/DOWN , direct change to **dB PSDIM UP DIM DOWN **:00 to 99 by ASCII , 00=0, PSDIM DOWN DIM ** ---AVR-X3000 can be operated from 0 to 6 PSDIM ** DIM ? Return PSDIM Status PSDIM ? CEN UP CENTER WIDTH UP/DOWN , direct change to **dB PSCEN UP CEN DOWN **:00 to 99 by ASCII , 00=0 PSCEN DOWN CEN ** ---AVR-X3000 can be operated from 0 to 7 PSCEN 07
COMMAND PS PARAMETER RSTR OFF RSTR LOW RSTR MED RSTR HI RSTR ? FRONT SPA FRONT SPB FRONT SPA+B FRONT? function AUDIO RESTORER direct change Return PSRSTR Status FRONT SPEAKER direct change Return PSFRONT Status - 19 - example PSRSTR OFF PSRSTR LOW PSRSTR MED PSRSTR HI PSRSTR ? PSFRONT SPA PSFRONT SPB PSFRONT A+B PSFRONT?
PARAMETER function OFF Picture Mode=OFF STD Picture Mode=STANDARD MOV Picture Mode=MOVIE VVD Picture Mode=VIVID STM Picture Mode=STREAM CTM Picture Mode=CUSTOM ? Return PV Status CN UP CONTRAST UP/DOWN , direct change to **dB CN DOWN **:44 to 56 by ASCII , 50=0 CN ** --- AVR-X3000 can be operated from -6 to +6(44 to 56) CN ? Return PVCN Status BR UP BRIGHTNESS UP/DOWN , direct change to **dB BR DOWN **:00 to 12 by ASCII , 00=0 BR ** --- AVR-X3000 can be operated from 0 to 12 BR ? Return PVBR Status ST UP Sa
example Z2CD | | USB/IPOD Z2USB/IPOD USB Z2USB IPD Z2IPD IRP Z2IRP FVP Z2FVP SOURCE Z2SOURCE UP Z2UP DOWN Z2DOWN **:00 to 98 by ASCII , 80=80(0dB), 00=-0(--dB)(MIN) ** Z280 ON ZONE2 ON/OFF change Z2ON OFF Z2OFF ? Return Z2 Status Z2? Z2MU ON ZONE2 OUTPUT MUTE ON/OFF change Z2MUON OFF Z2MUOFF ? Return Z2MU Status Z2MU? Z2CS ST ZONE2 Channel setting Z2CSST MONO Z2CSMONO ? Return Z2CS Status Z2CS? Z2CV FL UP ZONE2 CHANNEL VOLUME UP/DOW
PARAMETER function BAS UP ZONE2 BASS UP/DOWN , direct change to **dB BAS DOWN **:00 to 99 by ASCII , 00=0dB BAS ** ---AVR-X3000 can be operated from -10 to +10(40 to 60) BAS ? Return Z2PSBAS Status TRE UP ZONE2 TREBLE UP/DOWN , direct change to **dB TRE DOWN **:00 to 99 by ASCII , 00=0dB TRE ** ---AVR- X3000 can be operated from -10 to +10(40 to 60) TRE ? Return Z2PSTRE Status Z2SLP OFF ZONE2 SLEEP TIMER setting *** ***:001 to 120 by ASCII , 010=10min ? Return Z2SLP Status Z2 FAVORITE1 ZONE2 FAVORITE STATIO
ANALOG TUNER Control function TUNER Frequency UP/DOWN --- ****.** MHz at FM band (<050000 is FM.) Return TF Status TUNER PRESET CH UP/DOWN , direct change to No.** ** 01-56 01=CH01,56=CH56 TM example TFANUP TFANDOWN TFAN008750 (87.50MHz at FM) TFAN? TPANUP TPANDOWN TPAN01 (PRESET No.”01”) TPAN? TPANMEM TPANMEM** Return TP Status TUNER PRESET MEMORY TUNER PRESET MEMORY, Preset stored at No.
Network Audio/USB /iPod DIRECT Extended Control PARAMETER 90 91 92 93 94 9A 9B 9C 9D 9E 9F 9G 9H 9I 9J 9K 9M function “Cursor Up” Control “Cursor Down” Control “Cursor Left” Control “Cursor Right” Control “Enter (Play/Pause)” Control “Play” Control(iRadio/mServer/USB) “Play/Pause” Control(iPod Direct) “Pause” Control “Play/Pause” Control(iPod Direct) “Stop” Control “Skip Plus” Control “Skip Minus” Control “Manual Search Plus” Control(USB/iPod) “Manual Search Plus” Control(USB/iPod) “Repeat One” (USB/iPod D
(Return NSA0-NSA8,Refer to Page 39 NSE Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel 01-56 status UTF-8 example NSA (Return NSE0-NSE8,Refer to Page 40 NSD0 (*:0-9,A-Z) NSB00 NSC00 B** (PRESET No.) C** (PRESET No.
Cursor/Enter/Setup Menu COMMAND MN PARAMETER CUP CDN CLT CRT ENT RTN OPT INF MEN ON MEN OFF MEN? PRV ON PRV OFF PRV? ZST ON ZST OFF function “Cursor Up” Control “Cursor Down” Control “Cursor Left” Control “Cursor Right” Control “Enter” Control “RETURN” Control “OPTION” Control “INFO” Control “Setup Menu ON” Control “Setup Menu OFF” Control Return MNMEN(Menu) status “InstaPrevue ON” Control “InstaPrevue OFF” Control Return MNPRV(InstaPrevue) status "All Zone Stereo ON" direct Control "All Zone Stereo OFF"
Remote Lock/Panel Lock COMMAND SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON (Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL.
EVENT(or RESPONSE) and PARAMETER list EVENT PW MV CV PARAMETER ON STANDBY ** FL ** FR ** C ** SW ** SL ** SR ** SBL ** SBR ** SB ** FHL ** FHR ** FWL ** FWR ** MU ON OFF SI CD TUNER DVD BD TV SAT/CBL MPLAY GAME AUX1 The PARAMETER of MV, CV EVENT function POWER ON/STANDBY change MASTER VOLUME change , **:00 to 98 by ASCII 98 = 18dB(MAX) 80 = 00dB 01 = -79dB 005 = -79.
EVENT SI ZM PARAMETER NET PANDORA SIRIUSXM SPOTIFY FLICKR FAVORITES IRADIO SERVER USB/IPOD USB DIRECT IPOD DIRECT USB IPD IRP FVP ON OFF FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY function ---NETWORK (North America model Only) (North America model Only) (North America & Europe model Only) ---iPod/USB MAIN ZONE ON/OFF change FAVORITE STATION 1-3 MODE SELECT FAVORITE STATION 1-3 MODE MEMORY - 29 - example SINET SIPANDORA SISIRIUSXM SISPOTIFY SIFLIC
EVENT SD DC SV SLP PARAMETER AUTO HDMI DIGITAL ANALOG ARC NO AUTO PCM DTS ON OFF DVD BD TV SAT/CBL MPLAY GAME AUX1 CD OFF *** function INPUT mode change ARC playing No Input DIGITAL INPUT mode change VIDEO SELECT mode set VIDEO SELECT mode cancel VIDEO SELECT mode set to ON, and select source ---Blu-ray ---TV AUDIO ---CBL/SAT ---MEDIA PLAYER ---AUX MAIN ZONE SLEEP TIMER setting change - 30 - example SDAUTO SDHDMI SDDIGITAL SDANALOG SDARC SDNO DCAUTO DCPCM DCDTS S
EVENT MS PARAMETER DIRECT PURE DIRECT STEREO MULTI CH IN M CH IN+PL2X C M CH IN+PL2X M M CH IN+PL2Z H M CH IN +DOLBY EX MULTI CH IN 7.
EVENT MS PARAMETER DTS NEO:X C DTS NEO:X M DTS NEO:X G DTS SURROUND DTS ES DSCRT6.1 DTS ES MTRX6.1 DTS+PL2X C DTS+PL2X M DTS+PL2Z H DTS+NEO:X C DTS+NEO:X M DTS+NEO:X G DTS96/24 DTS96 ES MTRX MCH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE MATRIX VIDEO GAME VIRTUAL DOLBY D+ DOLBY D+ +EX DOLBY D+ +PL2X C DOLBY D+ +PL2X M DOLBY D+ +PL2Z H DOLBY D+ +NEO:X C DOLBY D+ +NEO:X M DOLBY D+ +NEO:X C function - 32 - example MSDTS NEO:X C MSDTS NEO:X M MSDTS NEO:X G MSDTS SURROUND MSDTS ES DSCRT6.
EVENT PARAMETER DOLBY TRUEHD DOLBY HD DOLBY HD+EX DOLBY HD+PL2X C DOLBY HD+PL2X M DOLBY HD+PL2Z H DOLBY HD+NEO:X C DOLBY HD+NEO:X M DOLBY HD+NEO:X G DTS HD DTS HD MSTR DTS HD+PL2X C DTS HD+PL2X M DTS HD+PL2Z H DTS HD+NEO:X C DTS HD+NEO:X M DTS HD+NEO:X G DTS ES 8CH DSCRT DTS EXPRESS ALL ZONE STEREO function - 33 - example MSDOLBY HD MSDOLBY HD MSDOLBY HD+EX MSDOLBY HD+PL2X C MSDOLBY HD+PL2X M MSDOLBY HD+PL2Z H MSDOLBY HD+NEO:X C MSDOLBY HD+NEO:X M MSDOLBY HD+NEO:X G M
EVENT MS PARAMETER QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 function QUICK SELECT mode change ---QUICK 1(or 2, 3, 4, 5) Change QUICK SELECT OFF - 34 - example MSQUICK1 MSQUICK2 MSQUICK3 MSQUICK4 MSQUICK5 MSQUICK0
EVENT VS PARAMETER ASPNRM ASPFUL SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO AUDIO AMP AUDIO TV VPMAUTO VPMGAME VPMMOVI function ASPECT setting change NRM=4:3 , FUL=16:9 Resolution(analog) setting change Resolution(HDMI) setting change HDMI AUDIO Output setting change Video Mode setting change - 35 - example VSASPNRM VSASPFUL VSSC48P VSSC10I VSSC72P VSSC10P VSSC10P24 VSSC4K VSSCAUTO VSSCH48P VSSCH10I VSSCH72
EVENT PS PARAMETER TONE CTRL OFF TONE CTRL ON CINEMA EQ.ON CINEMA EQ.OFF MODE:CINEMA MODE:MUSIC MODE:GAME MODE:HEIGHT LOM ON LOM OFF PHG LOW PHG MID PHG HI MULTEQ:AUDYSSEY MULTEQ:BYP.LR MULTEQ:FLAT MULTEQ:MANUAL MULTEQ:OFF DYNEQ ON DYNEQ OFF REFLEV 0 REFLEV 5 REFLEV 10 REFLEV 15 DYNVOL HEV DYNVOL MED DYNVOL LIT DYNVOL OFF DSX ONH DSX ONW DSX OFF STW ** STH ** function TONE CONTROL ON/OFF change CINEMA EQ.
PARAMETER function BAS ** BASS change TRE ** TREBLE change DRC AUTO Dynamic Compression change DRC LOW When the input signal is Dolby TrueHD DRC MID DRC HI DRC OFF LFE ** LFE change EFF ** EFFECT LEVEL change DEL *** DELAY change PAN ON PANORAMA ON/OFF change PAN OFF DIM ** DIMMENSION change CEN ** CENTER WIDTH change CEG ** CENTER GAIN change SWR ON SW ON/OFF change SWR OFF RSZ S ROOM SIZE change RSZ MS RSZ M RSZ ML RSZ L DELAY *** AUDIO DELAY change RSTR OFF AUDIO RESTORER change RSTR LOW RSTR MED RSTR HI
EVENT PV PARAMETER OFF STD MOV VVD STM CTM CN ** BR ** ST ** HUE ** DNR OFF DNR LOW DNR MID DNR HI ENH ** function Picture Mode=OFF Picture Mode=STANDARD Picture Mode=MOVIE Picture Mode=VIVID Picture Mode=STREAM Picture Mode=CUSTOM CONTRAST change BRIGHTNESS Change Saturation change Hue Change DNR change ENHANCER change - 38 - example PVOFF PVSTD PVMOV PVVVD PVSTM PVCTM PVCN 50 PVBR 12 PVST 50 PVHUE 50 PVDNR OFF PVDNR LOW PVDNR MID PVDNR HI PVENH
EVENT Z2 PARAMETER CD | USB DIRECT IPOD DIRECT SOURCE QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY ** function ZONE2 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
EVENT Z2CS Z2CV Z2HPF Z2PS PARAMETER ST MONO FL ** FR ** ON OFF BAS ** TRE ** function ZONE2 Channel setting **:38 to 62 by ASCII , 50=0dB **:38 to 62 by ASCII , 50=0dB ZONE2 HPF ON/OFF change ZONE2 BASS change ZONE2 TEBLE change - 40 - example Z2CSST Z2CSMONO Z2CVFL 50 Z2CVFR 50 Z2HPFON Z2HPFOFF Z2PSBAS 50 Z2PSTRE 50
ANALOG TUNER Control AN**(PRESET No.) function TUNER Frequency change --- ****.** kHz at AM band ****.** MHz at FM band TUNER PRESET change to No.** ** 01-56 01=CH01,56=CH56 Change Preset Channel select OFF TUNER PRESET MEMORY ** 01-56 01=CH01,56=CH56 ---Band set to AM ---Band set to FM ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode (1050.00kHz at AM) TPAN01 (PRESET No.
Network Audio/USB /iPod DIRECT Extended Control EVENT PARAMETER NSA 0 1 2 3 4 5 6 7 8 function Onscreen Display Information is Answered By the NSA Command.
EVENT PARAMETER NSE 0 1 2 3 4 5 6 7 8 function Onscreen Display Information(mServer/iRadio) is Answered By the NSE Command.
Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel CH1-CH56 status UTF-8 ** 00-55 00=CH01,55=CH56 NSB00 NSC00 - 44 - B** (PRESET No.) C** (PRESET No.
Cursor/Enter/Setup Menu COMMAND MN PARAMETER MEN ON MEN OFF PRV ON PRV OFF ZST ON ZST OFF function “Setup Menu ON” Control “Setup Menu OFF” Control “InstaPrevue ON” Control “InstaPrevue OFF” Control “All Zone Stereo ON” Control “All Zone Stereo OFF” Control MNMEN MNMEN MNPRV MNPRV MNZST MNZST example ON OFF ON OFF ON OFF TRIGGER CONTROL EVENT TR PARAMETER 1 ON 1 OFF function example Trigger 1 ON Trigger 1 OFF TR1 ON TR1 OFF function REMOTE CONTROL LOCK ON/OFF exam
Extension COMMAND The RC code can be sent from Serial protocol commands Protocol specification Command structure: COMMAND + RC FORMAT + RC DATA + CR (0x0D) COMMAND : ASCII CODE of 2 characters Ex. RC : RC CODE RC FORMAT : ASCII CODE of 3 characters Ex. KSK : KASEIKYO FORMAT SHP : SHARP FORMAT RC DATA : ASCII CODE of 7 characters For details of the RC CODE , please refer to the IR remote control code list.
The example of a command * is the meaning of 0x0D.
