DENON AVR control protocol Ver.04 Application model : AVR-2113CI/AVR-1913 Application terminal: Ethernet RS-232C (AVR-2113CI only) Rev 8.5.0 Connector specification .
RJ-45(10BASE-T/100BASE-TX) .
NETWORK SETUP of AVR-2113CI/AVR-1913 >Procedure of Network Setup mode. (1)Press SETUP MENU button, then Menu appears on FL-display(and GUI) (2)Select “Setup Menu > Network > Settings ” . (3)Set parameters described below. "ON"---Use this setting when DHCP server is on the local network. "OFF"---Use this setting when DHCP server is not on the local network. When sets "OFF”, please set IP address. When sets "ON”, you can confirm the IP address that is set by server.
Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT.
The example of a command * is the meaning of 0x0D.
Others A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50".
COMMAND and PARAMETER list PARAMETER function example ON POWER ON/STANDBY change PWON STANDBY PWSTANDBY ? Return PW Status PW? MV UP MASTER VOLUME UP/DOWN , direct change to **(**dB) MVUP DOWN MVDOWN **:00 to 98 by ASCII , 80=80(0dB), 00=-0(--dB)(MIN) ** MV80 ? Return MV Status MV? CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP FL DOWN ---FRONT Lch CVFL DOWN FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50 FR UP CVFR UP FR DOWN ---FRONT Rch CVFR DOWN
PARAMETER function example SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP SB DOWN CVSB DOWN SB ** **:38 to 62 by ASCII , 50=0dB CVSB 50 FHL UP CVFHL UP FHL DOWN ---FRONT HEIGHT Lch CVFHL DOWN FHL ** **:38 to 62 by ASCII , 50=0dB CVFHL 50 FHR UP CVFHR UP FHR DOWN ---FRONT HEIGHT Rch CVFHR DOWN FHR ** **:38 to 62 by ASCII , 50=0dB CVFHR 50 ? Return CV Status CV? MU ON VOLUME MUTE ON/OFF change MUON OFF MUOFF ? Return MU Status MU? SI CD Select INPUT source SICD
COMMAND SI ZM PARAMETER NET PANDORA SIRIUSXM SPOTIFY LASTFM FLICKR FAVORITES IRADIO SERVER USB/IPOD USB IPD IRP FVP ? ON OFF ? FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY function ---NETWORK (North America model Only) (North America model Only) (North America & Europe model Only) (Europe model Only) example SINET SIPANDORA SISIRIUSXM SISPOTIFY SILASTFM SIFLICKR SIFAVORITES SIIRADIO SISERVER Select iPod/USB SIUSB/IPOD Select INP
COMMAND SD DC SV SLP PARAMETER AUTO HDMI DIGITAL ANALOG ? AUTO PCM DTS ? DVD BD TV SAT/CBL MPLAY GAME AUX1 CD SOURCE ? OFF *** ? function set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) set force HDMI INPUT mode set force DIGITAL INPUT (Optical,Coaxial)mode set force ANALOG INPUT mode Return SD Status set DIGITAL INPUT AUTO mode set DIGITAL INPUT force PCM mode set DIGITAL INPUT force DTS mode Return DC Status VIDEO SELECT mode set , and select source ---Blu-ray ---TV AUDIO ---CBL/SAT ---MediaPlayer ---
COMMAND MS PARAMETER MOVIE MUSIC GAME DIRECT PURE DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND MCH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE MATRIX VIDEO GAME VIRTUAL ? QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK4 MEMORY QUICK5 MEMORY QUICK ? function Select SURROUND mode ---MULTI CH STEREO mode Return MS Status QUICK SELECT 1-5 MODE SELECT QUICK SELECT 1-5 MODE MEMORY Return MSQUICK Status - 11 - example MSMOVIE MSMUSIC MSGAME MSDIRECT MSPURE
COMMAND VS PARAMETER ASPNRM ASPFUL ASP ? SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SC ? SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO SCH ? AUDIO AMP AUDIO TV AUDIO ? VPMAUTO VPMGAME VPMMOVI VPM ? function Set Aspect Ratio to 4:3 mode Set Aspect Ratio to 16:9 mode Return VSASP Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolution to 720p Set Resolution to 1080p Set Resolution to 10P24 Set Resolution to 4K (AVR-2113 model only) Set Resolution to AUTO Return VSSC Status Set Resolu
MODE: ? LOM ON LOM OFF LOM ? FH:ON FH:OFF FH: ? PHG LOW PHG MID PHG HI PHG ? function PARAMETER setting TONE CONTROL ON/OFF Return PSTONE CONTROL Status SURROUND BACK SP MODE set Return PSSB: Status CINEMA EQ. ON/OFF Return PSCINEMA EQ.Status CINEMA / MUSIC / GAME / PL mode change (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.
COMMAND PS PARAMETER MULTEQ:AUDYSSEY MULTEQ:BYP.
PARAMETER function BAS UP BASS UP/DOWN , direct change to **dB PSBAS BAS DOWN **:00 to 99 by ASCII , 50=0dB PSBAS BAS ** ---AVR-2113/AVR-1913 can be operated from -6 to +6(44 to 56) PSBAS BAS ? Return PSBAS Status PSBAS TRE UP TREBLE UP/DOWN , direct change to **dB PSTRE TRE DOWN **:00 to 99 by ASCII , 50=0dB PSTRE TRE ** ---AVR-2113/AVR-1913 can be operated from -6 to +6(44 to 56) PSTRE TRE ? Return PSTRE Status PSTRE DRC AUTO Dynamic Compression direct change PSDRC DRC LOW PSDRC DRC MID PSDRC DRC HI PSDRC
PARAMETER function example PAN ON PANORAMA ON/OFF PSPAN ON PAN OFF PSPAN OFF PAN ? Return PSPAN Status PSPAN ? DIM UP DIMENSION UP/DOWN , direct change to **dB PSDIM UP DIM DOWN **:00 to 99 by ASCII , 00=0, PSDIM DOWN DIM ** ---AVR-2113/AVR-1913 can be operated from 0 to 6 PSDIM ** DIM ? Return PSDIM Status PSDIM ? CEN UP CENTER WIDTH UP/DOWN , direct change to **dB PSCEN UP CEN DOWN **:00 to 99 by ASCII , 00=0 PSCEN DOWN CEN ** ---AVR-2113/AVR-1913 can be operated from 0
COMMAND PS PARAMETER RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3 RSTR ? FRONT SPA FRONT SPB FRONT SPA+B FRONT? function AUDIO RESTORER direct change Return PSRSTR Status FRONT SPEAKER direct change Return PSFRONT Status - 17 - example PSRSTR OFF PSRSTR MODE1 PSRSTR MODE2 PSRSTR MODE3 PSRSTR ? PSFRONT SPA PSFRONT SPB PSFRONT A+B PSFRONT?
example Z2CD | | USB/IPOD Z2USB/IPOD USB Z2USB IPD Z2IPD IRP Z2IRP FVP Z2FVP SOURCE Z2SOURCE UP Z2UP DOWN Z2DOWN **:00 to 98 by ASCII , 80=80(0dB), 00=-0(--dB)(MIN) ** Z280 ON ZONE2 ON/OFF change Z2ON OFF Z2OFF ? Return Z2 Status Z2? Z2MU ON ZONE2 OUTPUT MUTE ON/OFF change Z2MUON OFF Z2MUOFF ? Return Z2MU Status Z2MU? Z2CV FL UP ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB Z2CVFL UP FL DOWN ---FRONT Lch Z2CVFL DOWN FL ** **:38 t
NOTE: Z2 COMMAND function ZONE2 FAVORITE STATION 1-3 MODE SELECT ZONE2 FAVORITE STATION 1-3 MODE MEMORY ZONE2 QUICK SELECT 1-5 MODE SELECT ZONE2 QUICK SELECT 1-5 MODE MEMORY Return Z2QUICK Status PARAMETER FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK4 MEMORY QUICK5 MEMORY QUICK ? COMMAND Z2 when “ZONE2” is selected with “Amp Assign” at AVR-1913.
ANALOG TUNER(FM) Control function TUNER Frequency UP/DOWN --- ****.** MHz at FM band (<050000 is FM.) Return TF Status TUNER PRESET CH UP/DOWN , direct change to No.** ** 01-56 01=CH01,56=CH56 Return TP Status TUNER PRESET MEMORY TUNER PRESET MEMORY, Preset stored at No.** ** 01-56 01=CH01,56=CH56 Return TM Status ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode example TFANUP TFANDOWN TFAN008750 (87.
Network Audio/USB /iPod DIRECT Extended Control COMMAND NS PARAMETER 90 91 92 93 94 9A 9B 9C 9D 9E 9H 9I 9J 9K example NS90 NS91 NS92 NS93 NS94 NS9A NS9B NS9C NS9D NS9E NS9H NS9I NS9J NS9K NS9M 9M function “Cursor Up” Control “Cursor Down” Control “Cursor Left” Control “Cursor Right” Control “Enter (Play/Pause)” Control “Play” Control(iRadio/mServer/USB) “Play/Pause” Control(iPod Direct) “Pause” Control “Play/Pause” Control(iPod Direct) “Sto
example NSB00 function Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel 01-56 status UTF-8 NSC00 - 22 - PARAMETER B** (PRESET No.) C** (PRESET No.
Cursor/Enter/Setup Menu COMMAND MN PARAMETER CUP CDN CLT CRT ENT RTN OPT INF MEN ON MEN OFF function “Cursor Up” Control “Cursor Down” Control “Cursor Left” Control “Cursor Right” Control “Enter” Control “RETURN” Control “OPTION” Control “INFO” Control “Setup Menu ON” Control “Setup Menu OFF” Control example MNCUP MNCDN MNCLT MNCRT MNENT MNRTN MNOPT MNINF MNMEN ON MNMEN OFF - 23 -
Remote Lock/Panel Lock COMMAND SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON (Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL.
EVENT(or RESPONSE) and PARAMETER list EVENT PW MV CV PARAMETER ON STANDBY ** FL ** FR ** C ** SW ** SL ** SR ** SBL ** SBR ** SB ** FHL ** FHR ** MU ON OFF SI CD TUNER DVD BD TV SAT/CBL MPLAY GAME AUX1 The PARAMETER of MV, CV EVENT function POWER ON/STANDBY change MASTER VOLUME change , **:00 to 98 by ASCII 98 = 18dB(MAX) 80 = 00dB 01 = -79dB 005 = -79.5dB 00 = ---(MIN) CHANNEL VOLUME change , **:00,38 to 62 by ASCII 62 = +12dB(MAX) 50 = 0dB 38 = -12dB(MIN) 00 = OFF (define ONLY SWch in DIRECT mode.
EVENT SI ZM PARAMETER NET PANDORA SIRIUSXM SPOTIFY LASTFM FLICKR FAVORITES IRADIO SERVER USB/IPOD USB DIRECT IPOD DIRECT USB IPD IRP FVP ON OFF FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY function ---NETWORK (North America model Only) (North America model Only) (North America & Europe model Only) (Europe model Only) ---iPod/USB MAIN ZONE ON/OFF change FAVORITE STATION 1-3 MODE SELECT FAVORITE STATION 1-3 MODE MEMORY - 26 - example SINET SIPANDORA SISIRIUS
EVENT SD DC SV SLP PARAMETER AUTO HDMI DIGITAL ANALOG ARC NO AUTO PCM DTS DVD BD TV SAT/CBL MPLAY GAME AUX1 SOURCE OFF *** function INPUT mode change ARC playing No Input DIGITAL INPUT mode change VIDEO SELECT mode source change ---Blu-ray ---TV AUDIO ---CBL/SAT ---MediaPlayer ---GAME ---AUX MAIN ZONE SLEEP TIMER setting change - 27 - example SDAUTO SDHDMI SDDIGITAL SDANALOG SDARC SDNO DCAUTO DCPCM DCDTS SVDVD SVBD SVTV SVSAT/CBL SVMPLAY SVGAM
EVENT MS PARAMETER DIRECT PURE DIRECT STEREO MULTI CH IN M CH IN+PL2X C M CH IN+PL2X M M CH IN+PL2Z H M CH IN +DOLBY EX MULTI CH IN 7.1 DOLBY PRO LOGIC DOLBY PL2 C DOLBY PL2 M DOLBY PL2 G DOLBY PL2X C DOLBY PL2X M DOLBY PL2X G DOLBY PL2Z H DOLBY DIGITAL DOLBY D EX DOLBY D +PL2X C DOLBY D +PL2X M DOLBY D +PL2Z H DTS NEO:6 C DTS NEO:6 M DTS SURROUND DTS ES DSCRT6.1 DTS ES MTRX6.
EVENT PARAMETER DTS+NEO:6 DTS96/24 DTS96 ES MTRX MCH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE MATRIX VIDEO GAME VIRTUAL DOLBY D+ DOLBY D+ +EX DOLBY D+ +PL2X C DOLBY D+ +PL2X M DOLBY D+ +PL2Z H DOLBY TRUEHD DOLBY HD DOLBY HD+EX DOLBY HD+PL2X C DOLBY HD+PL2X M DOLBY HD+PL2Z H DTS HD DTS HD MSTR DTS HD+NEO:6 DTS HD+PL2X C DTS HD+PL2X M DTS HD+PL2Z H DTS ES 8CH DSCRT DTS EXPRESS MPEG2 AAC AAC+DOLBY EX AAC+PL2X C AAC+PL2X M AAC+PL2Z H function (JAPAN (JAPAN (JAPAN (JAPAN (JAPAN model model model model model O
EVENT MS PARAMETER QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 function QUICK SELECT mode change ---QUICK 1(or 2, 3, 4, 5) Change QUICK SELECT OFF - 30 - example MSQUICK1 MSQUICK2 MSQUICK3 MSQUICK4 MSQUICK5 MSQUICK0
EVENT VS PARAMETER ASPNRM ASPFUL SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO AUDIO AMP AUDIO TV VPMAUTO VPMGAME VPMMOVI function ASPECT setting change NRM=4:3 , FUL=16:9 Resolution(analog) setting change (AVR-2113 model only) Resolution(HDMI) setting change (AVR-2113 model only) HDMI AUDIO Output setting change Video Mode setting change - 31 - example VSASPNRM VSASPFUL VSSC48P VSSC10I VSSC72P VSSC10P VSSC10P24 VSSC4K VS
EVENT PS PARAMETER TONE CTRL OFF TONE CTRL ON SB:MTRX ON SB:PL2X CINEMA SB:PL2X MUSIC SB:ON SB:OFF SB:ESMTRX CINEMA EQ.ON CINEMA EQ.OFF MODE:CINEMA MODE:MUSIC MODE:GAME MODE:PRO LOGIC MODE:HEIGHT LOM ON LOM OFF FH:ON FH:OFF PHG LOW PHG MID PHG HI MULTEQ:AUDYSSEY MULTEQ:BYP.LR MULTEQ:FLAT MULTEQ:MANUAL MULTEQ:OFF DYNEQ ON DYNEQ OFF function TONE CONTROL ON/OFF change SURROUND BACK MODE change CINEMA EQ.
EVENT PS PARAMETER REFLEV 0 REFLEV 5 REFLEV 10 REFLEV 15 DYNVOL HEV DYNVOL MED DYNVOL LIT DYNVOL OFF BAS ** TRE ** DRC AUTO DRC LOW DRC MID DRC HI DRC OFF LFE ** EFF ** DEL *** function Reference Level Offset change DYNAMIC VOLUME change BASS change TREBLE change Dynamic Compression change When the input signal is Dolby TrueHD LFE change EFFECT LEVEL change DELAY change - 33 - example PSREFLEV 0 PSREFLEV 5 PSREFLEV 10 PSREFLEV 15 PSDYNVOL HEV PSDYNVOL MED PSDYNVOL LIT PSDY
EVENT PS PARAMETER PAN ON PAN OFF DIM ** CEN ** CEI ** SWR ON SWR OFF RSZ S RSZ MS RSZ M RSZ ML RSZ L DELAY *** RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3 FRONT SPA FRONT SPB FRONT SPA+B function PANORAMA ON/OFF change DIMMENSION change CENTER WIDTH change CENTER IMAGE change SW ON/OFF change ROOM SIZE change AUDIO DELAY change AUDIO RESTORER change FRONT SPEAKER direct change - 34 - example PSPAN ON PSPAN OFF PSDIM 06 PSCEN 07 PSCEI 10 PSSWR ON PSSWR OFF PSRSZ S PSRSZ M
EVENT Z2 PARAMETER CD | USB DIRECT IPOD DIRECT SOURCE QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY ** function ZONE2 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
ANALOG TUNER Control AN**(PRESET No.) function TUNER Frequency change --- ****.** kHz at AM band ****.** MHz at FM band TUNER PRESET change to No.** ** 01-56 01=CH01,56=CH56 Change Preset Channel select OFF TUNER PRESET MEMORY ** 01-56 01=CH01,56=CH56 ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode (1050.00kHz at AM) TPAN01 (PRESET No.
Network Audio/USB /iPod DIRECT Extended Control EVENT PARAMETER NSA 0 1 2 3 4 5 6 7 8 function Onscreen Display Information is Answered By the NSA Command.
EVENT PARAMETER NSE 0 1 2 3 4 5 6 7 8 function Onscreen Display Information(mServer/iRadio) is Answered By the NSE Command.
function example NSB00 NSC00 - 39 - Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel CH1-CH56 status UTF-8 ** 00-55 00=CH01,55=CH56 PARAMETER B** (PRESET No.) C** (PRESET No.
Remote Lock/Panel Lock EVENT SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL.
Extension COMMAND The RC code can be sent from Serial protocol commands Protocol specification Command structure: COMMAND + RC FORMAT + RC DATA + CR (0x0D) COMMAND : ASCII CODE of 2 characters Ex. RC : RC CODE RC FORMAT : ASCII CODE of 3 characters Ex. KSK : KASEIKYO FORMAT SHP : SHARP FORMAT RC DATA : ASCII CODE of 7 characters For details of the RC CODE , please refer to the IR remote control code list.
The example of a command * is the meaning of 0x0D.
