Installation Guide

ManualsBrandsDelta ManualsKitchenPalo Pull-Out Spray Assembly in Chrome

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Models/Modelos/Modèles

467-DST, 470-DST, 470-WE-DST,

472-DST, 473-DST & 473-SD-DST

Series/Series/Seria

SILICONE

Icons

9/28/15 Rev. D

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE

DEBE UTILIZAR CON MAQUINAS LAVAPLATOS PORTATILES! /

AVERTISSEMENT: ON NE DOIT PAS BRANCHER UN LAVE-VAISSELE

PORTATIF SUR CE ROBINET!

SINGLE HANDLE PULLOUT PALO

, SIGNATURE

AND SAXONY

KITCHEN FAUCETS

LLAVES EXTRAÍBLES DE AGUA PARA COCINAS

PALO

, SIGNATURE

Y SAXONY

ROBINETS À UNE MANETTE À BEC-DOUCHETTE

RÉTRACTABLE SIGNATURE

ET SAXONY

POUR

ÉVIERS DE CUISINE

1/8"

SILICONE

Icons

64940

Summary of content (12 pages)

PAGE 1
64940 Models/Modelos/Modèles 467-DST, 470-DST, 470-WE-DST, 472-DST, 473-DST & 473-SD-DST Series/Series/Seria SINGLE HANDLE PULLOUT PALO®, SIGNATURE® AND SAXONY® KITCHEN FAUCETS LLAVES EXTRAÍBLES DE AGUA PARA COCINAS PALO®, SIGNATURE® Y SAXONY® ROBINETS À UNE MANETTE À BEC-DOUCHETTE RÉTRACTABLE SIGNATURE® ET SAXONY® POUR ÉVIERS DE CUISINE Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
1 B. A. C. A. 1 2 1 B. 3 1 2 3 1 1 1 3 2 2 2 2 Faucet Installation Faucet Installation DECK MOUNT STYLE A. Place baseplate shanks (1) through mounting holes in deck. Option: If sink is uneven, use silicone sealant under the baseplate. B. Place escutcheon (1) over baseplate. Insert CENTER MOUNT STYLE C. Secure faucet to sink with mounting nut and washer (1). Tighten securely by hand. Using a Phillips screwdriver, tighten locking screws (2). Install locknuts (3) and hand-tighten. A.
PAGE 4
2 A. B. 1.5 gpm B. 2.2 gpm 3 Side View Vista Lateral Vue de Côté Side View Vista Lateral Vue de Côté 1 2 2 4 4 1 2 2 3 2 3 1 1 2 1 3 2 2 4 1 1 4 2 1 4 1 1 Hose Installation A. Pass hose (1) through faucet (2). Thread wand assembly (3) onto hose (1) to prevent hose from becoming lodged in faucet when installing weight (4). Slide hose weight (4) over other end of hose. B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hoses as shown.
PAGE 5
3 A. B. 2 OR 2 1 O 2 OU 3 1 4 3 2 1 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 6
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 7
4 5 5 A. B. 3 4 4 2 2 1 6 3 1 For Models with Soap Dispenser For models with soap dispenser. Remove nut (1). Insert body assembly (2) through selected hole in sink. Secure body assembly to sink with nut (1). From under the sink screw the bottle (3) onto the body assembly shank. Insert pump (4) down into the body assembly, then attach head assembly (5) to pump. NOTE: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz. into bottle.
PAGE 8
6 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 9
1/8" 1 2 3 Cleaning and Care Maintenance If faucet leaks from under handle: Remove handle and unthread trim cap (1). Using a wrench, ensure bonnet nut (2) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (2) is tightened securely with a wrench.* If faucet leaks from spout outlet–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (2) is tightened securely with a wrench.
PAGE 10
467-DST Models / Modelos / Modèles RP47154▲ Lever Handle & Set Screw Manijas de Palanca y Tornillo de Presión Manette et Vis de calage RP44792 Set Screw Tornillo de Presión Vis de calage RP44651s Dispenser Assembly Ensamble del Dispensador Distributeur RP51502▲ Cap Casquillo Embase RP51503 Bonnet & V-Ring Bonete y Aro-V Chapeau et Joint à lèvres RP50587 Valve Assembly Ensamble de la válvula Soupape RP44643s 1.
PAGE 11
RP28898▲ Lever Handle, Button & Set Screw Manijas de Palanca, Botón y Tornillo de Presión Manette, Bouton et Vis de calage 470-DST, 470-WE-DST & 472-DST Models / Modelos / Modèles RP152 Set Screw Tornillo de Presión Vis de calage RP28906 Button / Botón / Bouton RP51502▲ Cap Casquillo Embase RP51503 Bonnet & V-Ring Bonete y Aro-V Chapeau et Joint à lèvres RP32542s 1.
PAGE 12
473-DST & 473-SD-DST Models / Modelos / Modèles RP38645▲ Lever Handle, Button & Set Screw Manijas de Palanca, Botón y Tornillo de Presión Manette, Bouton et Vis de calage RP152 Set Screw Tornillo de Presión Vis de calage RP28906 Button / Botón / Bouton RP51502▲ Cap Casquillo Embase RP51503 Bonnet & V-Ring Bonete y Aro-V Chapeau et Joint à lèvres RP38643s 2.