Installation Guide

ManualsBrandsDelta ManualsBathtub DrainsRP391PB

COMPLETE BATH WASTES

DESAGÜES COMPLETOS

PARA BAÑOS

RENVOIS POUR BAIGNOIRE

COMPLETS

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

Models/Modelos/Modèles

RP291, RP391 & RP691

Series/Series/Seria

Para instalación fácil de su desagüe

Delta de bañera necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

bath waste you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Pour faciliter l’installation de votre

renvoi d’eau et trop-plein de baignoire

Delta, vous aurez besoin de ce qui suit:

• LIRE TOUTES les instructions avant de déb-

uter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

SILICONE

Icons

9/22/15 Rev. E

SILICONE

Icons

17853

www.deltafaucet.com

Summary of content (8 pages)

PAGE 1
COMPLETE BATH WASTES DESAGÜES COMPLETOS PARA BAÑOS RENVOIS POUR BAIGNOIRE COMPLETS 17853 Models/Modelos/Modèles RP291, RP391 & RP691 Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici. For easy installation of your Delta bath waste you will need: You may need/Usted puede necesitar/ Articles dont vous pouvez avoir besoin: TEF LON SI LIC ON E • To READ ALL the instructions completely before beginning.
PAGE 2
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
RP291, RP691 TRIP LEVER–BRASS PALANQUITA DE DESENGANCHE–BRONCE LEVIER–LAITON RP7420 Beveled Gasket Empaque Biselado Joint oblique Retainer Wire Alambre de Retención Fil de retenue Clevis Barra con Horquilla Feuillard Cotter Pin Chaveta de Dos Patas Goupille fendue RP31555s Overflow Plate & Screws Chapa de Desborde y Tornillos Plaque de trop-plein et Vis Retainer Screws Tornillos de Retención Vis de retenue RP6404s Overflow Plate Screws Tornillos de Chapa de Desborde Vis de plaque de trop-plein Detent S
PAGE 4
RP391 TRIP WASTE–POLYPROPYLENE PALANQUITA DE DESENGANCHE–POLIPROPILENO LEVIER–POLYPROPYLÈNE RP7420 Beveled Gasket Empaque Biselado Joint oblique RP31555s Overflow Plate & Screws Chapa de Desborde y Tornillos Plaque de trop-plein et Vis RP6404▲ Overflow Plate Screws Tornillos de Chapa de Desborde Vis de plaque de trop-plein Clevis Barra con Horquilla Feuillard Tub Tacks Tachuelas Cornières de fixation Cotter Pin Chava de Dos Patas Goupille fendue RP6403s Overflow Plate Assembly Ensamble para Placa de De
PAGE 5
CO NE SI LI CO NE C. 2 SI LI 1 B. A. 1 1 2 3 1 A. Remove old bath waste. Clean drain (1) and overflow hole (2) of any accumulated buildup. B. Apply silicone to underside of waste plug (1) and insert into drain hole. C. From underneath tub, slip black gasket (1) onto waste plug (2). Screw the waste plug into drain ell (3). Wipe off excess silicone. A. Retire el desagüe viejo de la bañera. Limpie cualquier acumulación de residuos del desagüe (1) y del orificio del rebosadero (2). B.
PAGE 6
2 A. Retaining Wire Tub Tacks B. C. 7 2 1 3 5 6 1 2 2 4 1 3 A. Assemble beveled gasket (1) to overflow ell (2), and adjust to fit angle of tub. Slide coupling nuts & gaskets (3) onto ells. B. Attach tee (1) to drain and overflow ell. Do not tighten coupling nuts (2). C. Assemble plunger assembly (1) as shown. To install plunger linkage to the approximate length, place plunger on bottom of tub.
PAGE 7
D. E. 5 F. 4 3 1 2 3 1 2 D. Insert plunger assembly (1) into overflow ell (2). Attach clevis (3) to overflow plate with cotter pin (4). Attach overflow plate (5) to ell with screws. E. Install dome strainer (1) to waste plug (2) with screw (3). Turn water supplies on. Run water into tub and drain. Test plunger assembly to ensure proper shut-off and drainage. Adjust length of plunger assembly if necessary. F. Check for leaks at arrows. Tighten coupling nuts if necessary.
PAGE 8
Notes / Notas / Notes 8 17853 Rev.