5.5 Horsepower Pressure Washer with 5760 Cleaning Units (Model DT2400CS) PART NO D27918 Rev.
SAFETY GUIDELINE/DEFINITIONS CONSUMER ....... 2 SAFTEY INFORMATION...2 OPERATING INSTRUCTIONS MAINTENANCE ......... 11-17 ................................ 17-18 IMPORTANT SAFETY INSTRUCTIONS ................................... 3-6 STORAGE ......................................... CONSUMER GENERAL AND SERVICE INFORMATION ......................................... 6 WARRANTY ............................................ CARTON TROUBLE SHOOTING 19-20 GUIDE ........ 21-22 SPANISH ................
F_I_ Read Operation Manual. Do not operate equipment until you have read OperaUon Manual for Safety, Assembly, Operation, and Maintenance InstxucUons. READ AND SAVE THESE INSTRUCTIONS HAZARD RISK OF EXPLOSION OR FIRE WHAT CAN HAPPEN • Spilled gasoline and it's vapors can become ignited from cigarette sparks, electrical arcing, exhaust gases, and hot engine components such as the muffler. HOW TO PREVENT IT • Shut off engine and allow it to cool before adding fuel to the tank.
HAZARD RISK OF INJURY OR PROPERTY DAMAGE WHEN TRANSPORTING OR STORING WHAT CAN HAPPEN HOW TO PREVENT IT = Fuel or oil can leak or spill and could resultin fire or breathing hazard, serious injuryor death can result.
HAZARD RISK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT • Unsafe operation of your pressure washer could lead to serious injury or death to you or others. • • IT Do not use chlorine bleach or any other corrosive compound. Become familiar with the operation and cony trois of the pressure washer. Keep operating area clear of all persons, pets, and obstacles. Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times.
HAZARD _RISK @ OF INJURY FROM SPRAY WHAT CAN HAPPEN HOW TO PREVENT IT • AJwayswearANSI approved7.87safety glasses.Wearprotective clothingto protect againstaccidentalspraying. • Never pointwand at,or spray people or animals. • Always securetriggerlock when wand is not in serviceto prevent accidentaloperation. • Never permanentlysecuretriggerin pull back (open)position. • High velocity fluidspray can cause objects to break, propelling particlesat high speed.
Accessories Panel [++] Manual Engine Frame, Wheel Assembly, andDual TankCleaning System f Bagged Accessories Panel Handle Knobs English/ Spanish/ French Operation Manual _ddle Nozzle Cleaning Kit Bolts O Chemical injector rinsing hose High Pressure Hose Bagged Pa_s Multi-Adjustable Spray Wand Spray Gun Engine Oil 7-ENG D27918
1. Remove cleaning solution away from frame assembly. 2. Place handle assembly onto frame and connect Knobs are assembled to the outside of frame. 3. Connect D27918 tanks from wand to gun. Tighten securely. 8-ENG frame assembly. Slide tanks handle to frame.
4. Attach , high pressure To Assemble hose to gun. Tighten Accessories securely. Panel a. Remove top screws on handle assembly, b. Loosen bottom screws on handle assembly. Remove Loosen c, Place grooves in accessories panel assembly into place. panel assembly onto screws and slide Screws d, Place screws (removed earlier) into the top holes and secure panel assembly to handles. Do not overtighten.
6. Reinstall cleaning solution tanks. Tilt cleaning solution tanks toward engine, slide onto handles, and snap into place. 7. Attach cleaning solution hose to barb fitting on control valve located at the rear of unit. 8. Add engine oil (supplied) to engine. Refer to Engine Owners Manual supplied by engine manufacturer for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing.
READ THIS OPERATION YOUR UNIT. Compare the location of various reference. MANUAL AND SAFETY RULES BEFORE OPERATING the illustrations with your unit to familiarize yourself with controls and adjustments. Save this manual for future Spray Gun High .Pressure Engine Dual Tank MultiAdjustable Cleaning System High Pressure Pump BASIC ELEMENTS OF A PRESSURE WASHER High Pressure Pump (located inside the shroud): water supply. Engine: Drives the high pressure pump. High Pressure and wand.
BASIC ELEMENTS OF ENGINE Refer to the engine manual for location and operation of engine controls. Choke Throttle Control: Control Opens and closes carburetor Lever: Controls engine speed. Fuel Valve Lever: Opens/closes Starter connection Grip: Pulling starter grip operates PRESSURE choke valve WASHER between fuel tank and carburetor. recoil starter to crank engine. TERMINOLOGY PSh Pounds per Square Inch. The unit of measure for air pressure, hydraulic pressure, etc. GPM: Gallons Per Minute.
HOW TO USE SPRAY WAND: Your pressure washer is equipped with a multi-adjustable spray wand with both high and low pressure settings. The high pressure setting is for cleaning and rinsing, the low pressure setting is for applying cleaning solutions to surfaces. When using the high pressure setting, DO NOT allow the jetlike spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious Risk of injection discharge For high pressure operation, wand as shown.
HOW TO USE THE DUAL TANK CLEANING SYSTEM NOTE: Use only soaps and cleaning solutions designed Do not use bleach. To apply cleaning for pressure washer use. solutions: 1. Make sure cleaning connected. 2. Turn control solution tanks are assembled valve knob arrow and all hoses are to the down (off) position as shown. Control Valve Knob . Fill cleaning solution tanks with desired cleaning solution. Each tank holds approximately 1.25 gallon.
READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT When using the hiah pressure setting. DO NOT allow the high pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury can occur. Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection mjudes.
4. Connect water source to pump inlet. NOTE: Water source must provide gallons per minute at 20 p.s.i. high pressure a minimum of 5 5. Connect 6. If applying a cleaning solution, see How To Use the Dual Cleaning Solution System in Operation section of this manual. 7. Turn water 8. Start engine. See Engine Owners Manual for correct procedure. NOTE: If the engine does not start after two pulls, pull the trigger to relieve the pressure. 9.
d. Before reconnecting cleaning solution hose to chemical injector barb fitting make sure that any remaining cleaning solution has been completely drained from the cleaning solution hose. To rinse chemical a. down b. using cleaning solution system tank 1 Turn control valve knob arrow to the (off) position. Fill one of the cleaning solution system tanks with clean water. c. Turn control valve knob toward tank with clean water. d.
1. Shut off the pressure 2. Disconnect spark plug wire to insure the unit will not start while performing maintenance. washer and turn off the water supply. 3. Pull trigger 4. 5. Disconnect the wand from the gun. Remove the nozzle from the end of the wand with the 2ram allen wrench on gun handle to relieve any water pressure. provided as shown. . . 8. Clean the nozzle using the nozzle cleaner provided or a straightened paper clip.
ENGINE Consult the Engine Owners Manual for the manufacturer's storage. recommendations for PUMP 1. Drain all water from high pressure pressure washer handle. hose, coil it, and store it in cradle of the 2. Drain all water from spray gun and spray wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun/hose holder. 3.
DUAL TANK CLEANING SYSTEM 1. Turn control valve knob to the down 2. Remove shroud. 3. Place end of cleaning cleaning solution. 4. Turn control 5. Repeat 6. Turn control 7. Fill tanks 8. Turn valve toward tank and drain water from tank. NOTE: This will rinse cleaning solution tanks, 9. Feed cleaning solution hose between shroud and wheel bracket it is routed over the axle as shown. Reconnect cleaning solution chemical injector for future use.
CAUSE PROBLEM Engine will not start (see Engine Manual for further engine troubleshooting) CORRECTION No fuel. Add Fuel, Pressure builds up after two pulls on the recoil starter or after initial use. Squeeze gun trigger to relieve Choke lever in the ,No Choke,' position, Move choke to the ',Choke', position. Spark plug wire not attached. Attach spark plug wire.
CAUSE PROBLEM Will not draw cleaning solution CORRECTION Wand not in low pressure. Filter ctogged on chemical injector rinsing hose. Screen on end of chemical rinsing hose not in water injecto See How to Use Wand paragraph in the Operation Section. Clean filter, Make sure end of chemical injector rinsing hose is fully submerged into clean water. Cleaning solution too thick, Dilute cleaning solution, Cleaning solution should be the same consistency as water.
-ENG D27918
DELTA MACHINERY warrants to the original pumhaser that all products covered under this warranty are free from defects in material and workmanship. Products covered under this warranty include air compressers, air tools, service parts, pressure washers, and generators, which have the following warranty periods: 3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM. 2 YEARS - Limited warranty on oil-lubricated air compressor pumps.
