Installation and Care Guide

ManualsBrandsDelta ManualsBlack Kitchen FaucetsSignature Pull Out Touch Hot and Cold Water Dispenser with Diamond Seal Technology

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODASlasinstruccionescompletamente

antesdeempezar.

•LEER TODOSlosavisos,cuidados,e

informacióndemantenimiento.

For easy installation of your Delta

faucet you will need:

•ToREAD ALLtheinstructionscompletely

beforebeginning.

•ToREAD ALLwarnings,care,andmaintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTESlesinstructionsavantdedébuter;

•LIRE TOUSlesavertissementsainsiquetoutes

lesinstructionsdenettoyageetd’entretien.

Models/Modelos/Modèles

470-DST&470-WE-DST

Series/Series/Seria

SILICONE

Icons

7/31/14   Rev.B

ASMEA112.18.1/CSAB125.1

MEETSOREXCEEDS—ASMEA112.18.1/CSAB125.1

ALCANZAOEXCEDELASSIGIENTESNORMAS—

ASMEA112.18.1/CSAB125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS!/ADVERTENCIA: ¡SESTALLAVENOSEDEBEUTILIZAR

CONMAQUINASLAVAPLATOSPORTATILES!/AVERTISSEMENT: ONNE

DOITPASBRANCHERUNLAVE-VAISSELEPORTATIFSURCEROBINET!

LEROBINETESTCONFORMEOUSUPÈRIEURAUXEXIGENCESDES

NORMESSUIVANTES:ASMEA112.18.1/CSAB125.1

SINGLE HANDLE PULLOUT SIGNATURE

KITCHEN FAUCETS

LLAVES EXTRAÍBLES DE AGUA PARA

COCINAS SIGNATURE

ROBINETS À UNE MANETTE À

BEC-DOUCHETTE RÉTRACTABLE

SIGNATURE POUR ÉVIERS DE CUISINE

1/8"

SILICONE

Icons

76075

Summary of content (12 pages)

PAGE 1
SINGLE HANDLE PULLOUT SIGNATURE® KITCHEN FAUCETS LLAVES EXTRAÍBLES DE AGUA PARA COCINAS SIGNATURE® ROBINETS À UNE MANETTE À BEC-DOUCHETTE RÉTRACTABLE SIGNATURE POUR ÉVIERS DE CUISINE 76075 ASME A112.18.1 / CSA B125.1 Models/Modelos/Modèles 470-DST & 470-WE-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 B. A. C. A. 1 2 1 B. 3 1 2 3 1 3 1 1 2 2 2 2 Faucet Installation Faucet Installation DECK MOUNT STYLE A. Place baseplate shanks (1) through mounting holes in deck. Option: If sink is uneven, use silicone sealant under the baseplate. B. Place escutcheon (1) over baseplate. Insert faucet (2) down into escutcheon assembly. CENTER MOUNT STYLE C. Secure faucet to sink with mounting nut and washer (1). Tighten securely by hand. Using a Phillips screwdriver, tighten locking screws (2).
PAGE 3
2 A. B. 2 OR 2 1 O 2 OU 3 1 4 3 2 1 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 4
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 5
3 4 1 A. 1 2 3 1 2 Flush Supply Lines Because your sprayer has been factory assembled to the hose, we do not recommend removing to flush the lines. Instead, if possible, we recommend placing a bucket below the outlet fitting and one of two options. 1. With the valve in mix open position (1), slowly open and close the supply stops (2). 2. With the supply stops open (2), slowly open and close the handle in the mix position (1). This will prevent debris from being lodged in the hose and sprayer.
PAGE 6
B. 1.5 gpm B. 1.8 gpm Side View Vista Lateral Vue de Côté Side View Vista Lateral Vue de Côté 2 2 4 1 2 3 2 2 1 1 2 1 3 4 2 4 1 3 2 4 1 1 1 Incorrect Installations. Instalacións incorrecta. Installations incorrecte. B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hoses as shown. Pull down moderately to ensure connection has been made. For 1.5 gpm “WE” models, use hose adapter (4) in place of clip (3). B.
PAGE 7
5 6 5 4 1 2 1 6 3 For Models with Soap Dispenser Remove nut (1). Insert body assembly (2) through selected hole in sink. Secure body assembly to sink with nut (1). From under the sink screw the bottle (3) onto the body assembly shank. Insert pump (4) down into the body assembly, then attach head assembly (5) to pump. NOTE: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz. into bottle. DO NOT remove bottle each time as this weakens the neck.
PAGE 8
7 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 9
1/8" 1 2 3 Maintenance If faucet leaks from under handle: Remove handle and unthread trim cap (1). Using a wrench, ensure bonnet nut (2) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (2) is tightened securely with a wrench.* If faucet leaks from spout outlet–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (2) is tightened securely with a wrench.
PAGE 10
470-DST & 470-WE-DST Models / Modelos / Modèles RP28898▲ Lever Handle, Button & Set Screw Manijas de Palanca, Botón y Tornillo de Presión Manette, Bouton et Vis de calage RP152 Set Screw Tornillo de Presión Vis de calage RP28906 Button / Botón / Bouton RP51502▲ Cap Casquillo Embase RP51503 Bonnet & V-Ring Bonete y Aro-V Chapeau et Joint à lèvres RP50587 Valve Assembly Ensamble de la válvula Soupape RP32542s 1.
PAGE 11
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 12
Notes / Notas / Notes 12 64940 Rev.