DIRECT-TO-STUD WALL SET PIEZAS PARA LA INSTALACIÓN DIRECTA AL MONTANTE MUR DE DOUCHE À FIXER AUX MONTANTS Model / Modelo / Modéle Write purchased model number here. Retain these instructions for future use. Escriba aquí el número del modelo comprado. Conserve estas instrucciones para usarlas en el futuro. Inscrivez le numéro de modèle ici. Conservez ces instructions pour consultation.
REQUIREMENTS FOR SUCCESSFUL INSTALLATION REQUISITOS PARA UNA INSTALACIÓN EXITOSA EXIGENCES À RESPECTER POUR RÉUSSIR L’INSTALLATION KNOWLEDGE BASE: Framing Plumbing • • • • Confirm that your model will fit in intended location and plumbing fixtures are located where required before beginning installation. Walls and sub-floor must be solid, plumb, and square. Do not install in areas where temperature may drop below 32ºF (0ºC).
TOOLS AND MATERIALS REQUIRED • 2” x 6” and 2’ x 4” lumber for additional wall studs • Lumber for bracing • Rags or padding to protect product during bracing NOTE: It is recommended to install insulation. HERRAMIENTAS Y MATERIALES NECESARIOS • Madera de 5,1 cm X 15,2 cm (2 “x 6”) y 5,1 cm X 10,2 cm (2 “x 4”)para montantes de pared adicionales • Madera para sostener • Trapos o acolchado para proteger el producto mientras lo apoya tablas NOTA: Se recomienda instalar el aislamiento.
ROUGHING-IN Rough plumbing must be installed before panel installation. For masonry construction, floor and walls must be framed to accommodate plumbing and installation. Studs should be located as shown below. CONEXIÓN DE CAÑERÍAS Deben instalarse las cañerías antes de instalar el panel. Para los trabajos de mampostería, el piso y las paredes deben acanalarse para dar lugar a las cañerías y la instalación. Los entramados deben estar ubicados como se muestra a continuación.
B67513-3636-WH 11 1/2" (29.2 cm) 12 1/4" (31.1 cm) 12 1/4" (31.1 cm) Horizontal 2" x 4" 12" (30. cm) 1 1/2" (3.8 cm) 12" (30. cm) 2 x 4 x 70-3/4” (5 x x 179.7 cm) (94.6 cm) ( 36" (91.4 cm) 40084 B67311-4834-WH 14 5/8” (37.2 cm) 9 3/8” (23.8 cm) 9 1/4" (23.5 cm) 14 5/8" (37.2 cm) " cm) 9 3/8" (23.8 cm) Horizontal 2" x 4" 12" (30.5 cm) 2 x 6 x 70-3/4” (5 x 15.2 x 179.7 cm) 35" (88.9 cm) 2 3/16" (43.3 cm) B67513-4834-WH 48" (121.9 cm) 9 3/8" (23.8 cm) 14 5/8” (37.2 cm) 14 5/8" (37.
B67513-6030-WH 15 3/8" (39 cm) 14 5/8” (37.2 cm) 14 5/8" (37 cm) Horizontal 2" x 4" 15 3/8” (39 cm) 1 1/2" (3.8 cm) (2 " cm) 12" (30. 2 x 4 x 70-3/4” x 179.7 cm) (5 x ” cm) ( 1 11/16" (4.3 cm) 60" (152.4 cm) 40104 B67311-6032-WH 15 3/8" (39.1 cm) 14 5/8" (37.1 cm) 14 5/8" (37.1 cm) 15 3/8" (39.1 cm) 9" (22.9 cm) 20 3/8" (51.8 cm) Horizontal 2" x 4" 28 3/4" (73 cm) 2 x 6 x 70” (5 x 15.24 x 177.8 cm) 33 1/4" (84.50 cm) 60" (152.4 cm) B67513-6032-WH 15 3/8" (39 cm) 14 5/8” (37.
1 Enclosure / Door Installation Only Solo para la instalación de la puerta/cabina Installation de l’enceinte, y compris les éléments pour la porte 40064, 40084, 40104, B67311-6032-WH, B67311-4834-WH 2 3/16” (5.56 cm) B67513-6032-WH, B67513-6030-WH, B67513-4834-WH, B67513-3636-WH 1 11/16” (4.3 cm) 70 3/4” (179.7 cm) 1 NOTE: It is recommended to install insulation on exterior walls. It is recommended that two people install this product. Use drop cloth to protect base from damage during installation.
2 B. A. 1 2 A. 1 Dry Fit Panel (opposite of drain) B. • Drill 3/16” holes at all stud locations on top flanges (1). • Drill 3/16” holes along side flanges (2) at locations equal distance apart. Do not drill holes directly into studs. Drill chuck can damage panel. Use an extended bit holder to reduce risk of drill chuck hitting panels. • Secure panel temporarily with a couple of screws. A. • Check panels for gaps and alignment.
3 A. B. X Back side of panel. Parte p osterior d el panel Face arrière du panneau. Y X Y A. Prepare for Plumbing Fixtures B. • Measure and mark location for plumbing fixtures on the front of the side panel. Drill pilot holes. • Using proper size hole saw, cut out plumbing fixture holes from back side of panel. A. • Remove backing from self-adhesive pad. • Center pad over mixing valve hole and press firmly onto back side of panel. • Using a utility knife, trim pad to reveal mixing valve hole.
4 B. A. 1 1 2 A A A S A. Preparing for Back Panel B. Secure Back Panel • Press back panel in place. • Secure top flanges (1) to studs with 1-1/4” panhead or roundhead screws. A Apply adhesive to studs up to the pencil line (1). S Apply sealant along back of base. NOTICE Do not use drywall screws to secure flanges to wall studs. Product damage will occur and will void the warranty. Do not overtighten screws, this can cause panel to crack.
5 B. A. A 3 1 S 2 S A. Preparing for Side Panels B. Secure Side Panels • Slide the side panel into gap between wall and back panel, pressing firmly into corner and against studs. • Push in and down until panel tops are even and curved area on side panel fits against back panel. • Secure top (1) and side flanges (2) to studs with 1-1/4” panhead or roundhead screws. Do not overtighten screws, this can cause panel to crack. • Repeat steps to secure other side panel.
6 7 1 S 2 Brace Wall Panels Apply Sealant • Protect surface of wall (1) where it will contact braces. • Install temporary braces (2) to hold side panels tight against studs while adhesive dries. S• Apply sealant to all seams. • Install plumbing fixtures and fittings per manufacturer’s instructions. • Check for leaks at all connections before use. IMPORTANT: Follow manufacturer’s instructions for adhesive dry time before removing brace.
CARE AND CLEANING We recommend that you clean your acrylic bathing product with mild detergents. Use a terry cloth towel, soft cloth, or sponge. Avoid using abrasive scrubbing pads, steel wool, or sponges. After cleaning, rinse thoroughly with water. NOTICE When using drain cleaner or clog remover, rinse thoroughly with water. Certain chemicals and cleaners may deteriorate the acrylic surface, causing cracks and, potentially, property damage.
Limited Warranty on Bathing Products This bathing product is warranted to the original consumer purchaser or commercial user, as applicable, to be free from defects in material and workmanship for the applicable period specified below: Delta®Tubs, Shower Bases, and Walls: Ten (10) years from the date of purchase by the original consumer purchaser or, for commercial users, one (1) year from the date of purchase.
