SHOWER BASE BASE PARA DUCHAS 109831 36" B11132-3636-WH Model / Modelo Write purchased model number here. Retain these instructions for future use. Escriba aquí el número del modelo comprado. Conserve estas instrucciones para usarlas en el futuro. 48" B11142-4834L-WH 48" B11142-4834R-WH 48" B11142-4834LC-WH 48" B11142-4834RC-WH 60" B11142-6032L-WH 60" B11142-6032R-WH 109831 www.deltafaucet.com 1 04/07/2021 109831 Rev.
! REQUIREMENTS FOR SUCCESSFUL INSTALLATION KNOWLEDGE BASE: Framing Plumbing These instructions include suggestions for rough construction and plumbing installation. Local building codes vary and could supersede those suggestions. If you are not confident in your ability to perform these tasks, contract out those tasks you need help with or use a professional installer. DO NOT use drywall screws to secure flanges to wall studs. Product damage will occur and will void the warranty.
TOOLS AND MATERIALS REQUIRED • 2 x 4 lumber for additional wall studs • Rags or padding to protect product during bracing HERRAMIENTAS Y MATERIALES NECESARIOS • Madera para montantes de pared si instala el juego para pared adicionales; consulte las instrucciones de instalación del juego para pared • Conjunto de drenaje y desbordamiento que encajan en una bañera con una profundidad de 41,9 cm (16-1/2”) Drill Safety Glasses Caulk Gun Sealant (2 tubes) Adhesive Taladro Antiparras de seguridad Pistola
ROUGHING-IN • • • • Rough plumbing must be installed before base installation. Minimum stud pocket sizes are shown below. Drain cutout 5” diameter max. Right side plumbing rough-in shown. For masonry construction, floor and walls must be framed to accommodate plumbing and installation. IMPORTANT: IF INSTALLING MATCHING ENCLOSURE, refer to Enclosure Installation Manual for specific lumber sizes and placement. Additional studs will be required and need to be installed at this point.
MODEL B11142-6032L-WH MODEL B11142-6032R-WH 60 3/4" (154cm) 15 1/8" (38 cm) 15 1/8" (38 cm) 32" (81 cm) 32" (81 cm) 8 7/16" (21 cm) 8 7/16" (21 cm) 60 3/4" (154cm) NOTES 5 109831 Rev.
Due to various thicknesses of tile and backer board available, ensure that you have enough room on the base for the enclosure, by shimming the base away from the studs as needed. Debido a los diversos espesores de las baldosas y placas de revestimiento disponibles, asegúrese de que hay suficiente espacio sobre la base para los accesorios através de calzar la base lejos de los montantes según sea necesario.
1 1 2 maximum máximo 5" (12.7 cm) 7/16" (1cm) Install Drain Pipe Dry fit base and verify that it is straight and square. Trace outline of drain and base. Ensure that the waste pipe is properly located to align with the drain assembly (not included). Subfloor maximum diameter opening: 5” Drain pipe to under 7/16" (1cm) subfloor: Instale la tubería del drenaje Seque la base ajustada y verifique que esté recta y en escuadra. Trace el contorno de las ubicaciones del drenaje y de la base.
! REQUIRED FOR PROPER INSTALLATION IF THE SUBFLOOR IS NOT FLAT AND LEVEL Entire bottom support must be in contact with a flat level surface as shown. If installation surface is not level, a mortar bed must be applied where the base will be positioned. REFER TO STEP 5 FOR INSTRUCTIONS. ! REQUIS POUR UNE BONNE INSTALLATION SI LE FAUX-PLANCHER N’EST PAS PLAT ET DE NIVEAU Le fond de la base au complet doit être en contact avec une surface plane de niveau comme le montre la figure.
1 3 4 1 2 3/16" (0,51cm) Attach drain (not included) following manufacturer’s instructions. NOTICE: Plumber’s putty will degrade base material. Do not use plumber’s putty to seal between drain and base or property damage may occur. Use silicone sealant or a gasket. Note: a drain is not included. Drill 3/16” holes at all stud locations on top flanges. NOTICE: Drill 3/16” clearance holes into flanges only. Do not drill 3/16” holes directly into studs. Drill chuck can damage base.
1 5 IF THE SUBFLOOR IS NOT FLAT AND LEVEL, a mortar bed must be applied where the base will be positioned. Apply a generous amount of mortar that has been mixed to a thick consistency. Use the mortar to fill in low areas. Place the base in the wet mortar, adjust until it is level, and let mortar cure for 24 hours. Proceed to step 6. 6 Shim #8 x 1-1/2" (3,81cm) IF THE SUBFLOOR IS FLAT AND LEVEL, apply adhesive on floor and spread using the notched side of the trowel, starting within pencil line.
CARE AND CLEANING 7 For regular cleaning use ONLY mild detergents or warm, soapy water. Use ONLY non-abrasive cloth or sponge. Always rinse surfaces after cleaning. Before cleaning this product with cleaning products, test a small, inconspicuous area. NOTICE: Manufacturer does not recommend the use of cleaning products that contain any of the following chemicals. Use of products containing these chemicals can cause the products to crack or discolor and will void the warranty.
LIMITED WARRANTY All parts and finishes of the Delta® Shower Base unit are warranted to the original consumer purchaser to be free from defects in material and workmanship for the time periods listed below. Delta recommends using a professional plumber for all installation and repair.
