(Model AP300) PART NO. 905588 - 05-13-02 Copyright © 2002 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, please call ESPAÑOL: PÁGINA 17 1-800-223-7278 (In Canada call 1-800-463-3582).
GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result.
ADDITIONAL SAFETY RULES FOR DUST COLLECTORS WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. 1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions. 14. DO NOT use the dust collector as a toy. DO NOT use near or around children. 2. OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine. 15.
POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3prong grounding type plugs and matching receptacle which will accept the machine’s plug.
nearest Authorized Service Center. The Service Center will be able to convert your dust collector for 240 volts by (a) re-wiring the motor for 240 volts; (b) installing a 240 volt attachment plug to the power supply cord; and (c) replacing the single pole on/off switch shipped with your dust collector with a double pole switch. The dust collector with a 240 volt plug should only be connected to an outlet having the same configuration as the plug illustrated in Fig. C.
DUST COLLECTOR PARTS 1 3 4 2 5 6 12 11 8 13 10 17 7 14 15 16 18 9 Fig. 2 1. 2. 3. 4. 5. 6. 7. 8. 9. Dust collector Hose Dust bag Exhaust flange Exhaust flange gasket Intake funnel Intake support angle brace Upper support bracket Lower tube support 10. 11. 12. 13. 14. 15. 16. 17. 18.
ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. WHEEL CASTERS 1. Remove the 3/8-16 hex nut and 3/8" lockwasher from each of the four wheel casters. A 2. Place the dust collector on its side. 3. Insert bolt on wheel caster through the four holes (A) Fig. 3 in the base of the dust collector. 4. Place a 3/8" lockwasher (A) Fig. 4 onto each bolt. Fig. 3 5.
DUST PORT TUBE AND CONNECTOR TO DUST COLLECTOR BODY A B 1. Place tube clamp (A) Fig. 7 on the lower support tube holder (B). Fig. 7 2. Insert the lower tube support (A) into the tube support holder (B) as shown in Fig. 8. A B Fig. 8 3. Place a tube clamp (A) onto the lower tube support as shown in Fig. 9. A Fig.
4. Align the two holes in the intake support angle brace (A) Fig. 10 with the two holes in the intake funnel (B). A B Fig. 10 5. Fasten the intake support angle brace to the intake funnel by inserting the two 5/16-18x5/8" button head carriage bolts (C) thru the intake funnel (B) and the intake support angle brace (A) as shown in Fig. 11. A B C Fig. 11 6. Place a 5/16" lockwasher (A) Fig. 12,onto the bolt (B), and thread a 5/16-18" hex nut (C) onto the bolt (B) and tighten securely. A B C Fig. 12 7.
8. Place intake funnel assembly (A), onto lower support tube (B) Fig. 14, and secure with tube clamp (C). A C B Fig. 14 VACUUM HOSE TO DUST COLLECTOR D 1. Place the intake cap holder (D) on the dust collector as shown in Fig. 15. NOTE: DO NOT COVER THE INTAKE PORT WITH THE INTAKE CAP WHEN ATTACHING THE HOSE TO THE INTAKE PORT. C 2. Place hose clamp (A) Fig. 15, onto one end of vacuum hose (B) and slide hose around intake port (C) as shown in Fig. 16. Tighten hose clamp (A). A B Fig. 15 C A Fig.
A B C 3. Place the remaining hose clamp (A) Fig. 17, around the other end of hose (B), slide hose (B) onto intake funnel (C), and tighten hose clamp (A). NOTE: If desired, intake funnel (C) can be rotated to the vertical position, as shown in Fig. 18. Fig. 17 C Fig. 18 A DUST BAG TO DUST COLLECTOR B Loosely thread end of dust bag strap (A) through clamp (B) as shown in Fig. 19. Place open end of dust bag (C) Fig. 19, over outlet flange (D) Fig.
OPERATING CONTROLS & ADJUSTMENTS WARNING: FOR OPERATOR SAFETY, MAKE CERTAIN THE DUST INTAKE PORT IS COVERED WITH THE HOSE BEFORE OPERATING THE MACHINE. THE ROTATING FAN INSIDE THE BLOWER HOUSING IS ACCESSIBLE THROUGH THE DUST INTAKE PORT AND IS HAZARDOUS. MAKE SURE INTAKE CAP COVERS THE INTAKE PORT WHEN HOSE IS REMOVED. ALWAYS WEAR PROPER APPAREL. DO NOT WEAR JEWELRY, AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF THE DUST INTAKE PORT. ALWAYS FOLLOW THE SAFETY RULES OF THIS MANUAL.
OPERATIONS This versatile dust collector is light, compact and can easily be transported for use in and out of the workshop. This dust collector can be used with many different types of woodworking machinery as shown in Figs. 26, 27, and 28. . Fig. 26 illustrates the dust collector used with a router. Note that the intake port is adjusted so that dust created by the router will be collected. Fig. 26 Fig. 27 illustrates the dust collector used with a table saw.
TRANSPORTATION AND STORAGE A 1. The dust collector features a convenient carrying handle with rubber grip (A) Fig. 29, which allows the unit to be carried easily from one job area to another. IMPORTANT: THE DUST COLLECTOR WEIGHS APPROXIMATELY 46 LBS. CARE SHOULD BE TAKEN WHEN LIFTING AND TRANSPORTING THE MACHINE. 2. In addition to the carrying handle, the machine features a storage mounting bracket (B) Fig. 30, with a hole for mounting the dust collector to a wall or wooden support when not in use. Fig.
NOTES 15
ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of your nearest supplier. WARNING: Since accessories other than those offered by Delta have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with this product.