Installation Instructions

ManualsBrandsDelta ManualsBathLinden Single Hole Single-Handle Vessel Sink Bathroom Faucet in Stainless

2/6/12 Rev. B

SILICONE

Models/Modelos/Modèles

594-DST & 794-DST

Series/Series/Seria

Linden™

Para instalación fácil de su llave Delta

usted necesitará:

sLEER TODAS las instrucciones completamente

antes de empezar.

sLEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

s4OREAD ALL the instructions completely

before beginning.

s4OREAD ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

SILICONE

Pour installer votre robinet Delta

facilement, vous devez:

sLIRE TOUTES les instructions avant de débuter;

sLIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

SILIC

SINGLE HANDLE LAVATORY

CENTERSET AND VESSEL FAUCETS

LLAVES MONOCONTROL DE MONTURA DE

CENTRO Y DE RECIPIENTE PARA LAVAMANOS

ROBINETS À UNE MANETTE POUR BASSIN

DE COMPTOIR ET

ENTRAXE COURT

1/8"

70649

www.deltafaucet.com

Summary of content (12 pages)

PAGE 1
70649 SINGLE HANDLE LAVATORY CENTERSET AND VESSEL FAUCETS LLAVES MONOCONTROL DE MONTURA DE CENTRO Y DE RECIPIENTE PARA LAVAMANOS ROBINETS À UNE MANETTE POUR BASSIN DE COMPTOIR ET ENTRAXE COURT Models/Modelos/Modèles 594-DST & 794-DST Series/Series/Seria Linden™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
LIFETIME FAUCET AND FINISH LIMITED WARRANTY All parts and finishes of the Delta® faucet are warranted to the original consumer purchaser to be free from defects in material & workmanship for as long as the original consumer purchaser owns their home. Delta Faucet Company recommends using a professional plumber for all installation & repair.
PAGE 3
1 For Three Hole Mount Para Las Instalaciones De Tres Agujeros 1 Montage Sur Trois Trous For Single Hole Mount Para Las Instalaciones De Un Agujero Montage sur un trou A. A. 2 1 1 2 B. B. 4 5 3 4 5 6 For three hole mount: For single hole mount: A. Slide single hole gasket (1) up over tubes and mounting stud. Position faucet (2) and gasket on sink. Option: If sink is uneven, use silicone under the gasket. A. Slide gasket (1) and escutcheon (2) up over tubes and mounting stud.
PAGE 4
2 A. B. OR 2 1 O 2 3 OU 4 3 2 1 1 2 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 5
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet ﬁtting (4).
PAGE 6
B. E. D. C. 1 SIL NE I CO 3 A. 1 2 3 2 3 2 1 1 1 F. G. 4 2 5 2 H. 3 4 2 1 5 1 2 3 2 1 6 Metal Pop-Up A. Remove stopper (1) and flange (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. D. Apply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2). E. Pivot (1) must face faucet. Pull assembly (2) down firmly and hold in place.
PAGE 7
4 3 1 2 2 4 4 Remove aerator (1) using supplied wrench (2) and turn faucet handle (3) to the full on mixed position. Turn on hot and cold water supplies (4) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. Reinstall aerator with wrench. Note: For future use, aerator wrench (2) can be clipped to the supply line after flushing faucet. Check all connections at arrows for leaks. Retighten if necessary, but do not overtighten.
PAGE 8
5 4 3 1 2 Cleaning and Care Maintenance If faucet exhibits very low flow: A. Remove and clean aerator (1) with supplied wrench (2), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (4) is tightened securely with a wrench.* If faucet leaks from under handle: Remove handle and unthread trim cap (5). Using a wrench, ensure bonnet nut (4) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3).
PAGE 9
Model / Modelo / Modèle 594-DST RP70623▲ Handle, Red/Blue Button & Set Screw Manija, Botón Rojo/Azul y Tornillo de Ajuste Manette, Bouton Rouge/ Bleu et Vis de Calage ▲Specify Finish Especifíque el Acabado Précisez le Fini RP54975 O-Ring Anillo O Joint torique RP37036 Set Screw Tornillo de Ajuste Vis de calage RP54972▲ Cap Casquillo Embase RP54976 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensamble de la válvula Soupape RP70624▲ Lift Rod & Finial Barra de Alzar y Pomo Tige de Manoeuvre et Grain de l
PAGE 10
Model / Modelo / Modèle 794-DST RP37036 Set Screw Tornillo de Ajuste Vis de calage RP70623▲ Handle, Button & Set Screw Manija, Botón l y Tornillo de Ajuste Manette, Bouton et Vis de Calage RP54972▲ Cap Casquillo Embase RP54975 O-Ring Anillo O Joint torique ▲Specify Finish Especifíque el Acabado Précisez le Fini RP54976 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensamble de la válvula Soupape RP54977 Aerator & Wrench Aereador y Llave Aérateur et Clé RP52217 Wrench Llave Clé RP47273 Gasket (1 Hole
PAGE 11
Notes / Notas / Notes 11 70649 Rev.
PAGE 12
70649 Rev.