Installation Guide

ManualsBrandsDelta ManualsCommercial Bathroom Faucets520LF-HDF

SILICONE

Icons

SINGLE HANDLE LAVATORY

CENTERSET FAUCETS

LLAVES MONOCONTROL DE MONTURA

DE CENTRO PARA LAVAMANOS

ROBINETS À ENTRAXE COURT À

UNE POIGNÉE

Models/Modelos/Modèles

501LF-HDF, 511LF-HDF, 515LF-HDF,

516LF-HDF, 520LF-HDF & 523LF-HDF

Series/Series/Seria

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODAS las instrucciones completamente

antes de empezar.

•LEER TODOS los avisos, cuidados, e

información de mantenimiento.

•Comprarlasconexionescorrectasparael

suministro de agua.

For easy installation of your Delta

faucet you will need:

•ToREAD ALL the instructions completely

before beginning.

•To READ ALL warnings, care, and maintenance

information.

•Topurchasethecorrectwater supply hook-up.

SILICONE

Icons

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

SILICONE

Icons

SILICONE

Icons

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTES les instructions avant

de débuter;

•LIRE TOUS les avertissements ainsi que toutes

•Acheterlebonnécessairederaccordement.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

3/7/13 Rev. B

ASMEA112.18.1/CSAB125.1

ASMEA112.18.2/CSAB125.2

1/8"

73420

www.deltafaucet.com

Summary of content (8 pages)

PAGE 1
SINGLE HANDLE LAVATORY CENTERSET FAUCETS 73420 LLAVES MONOCONTROL DE MONTURA DE CENTRO PARA LAVAMANOS ROBINETS À ENTRAXE COURT À UNE POIGNÉE ASME A112.18.1 / CSA B125.1 ASME A112.18.2 / CSA B125.2 Models/Modelos/Modèles 501LF-HDF, 511LF-HDF, 515LF-HDF, 516LF-HDF, 520LF-HDF & 523LF-HDF Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Cleaning and Care Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
PAGE 3
RP152 Set Screw Tornillo de Ajuste Vis de Calage RP47666 Set Screw Tornillo de Ajuste Vis de Calage RP52834 Handle & Set Screw Manija y Tornillo de Ajuste Manette et Vis de Calage RP51502 Cap Casquillo Embase RP60730 Wrench Llave Clé RP12516 Strap & Screw Barra Chata y Tornillo Feuillard et Vis RP23060 Flange Reborde Collerette RP6142 Gasket Empaque Joint RP6132 Nut Tuerca Écrou RP6140 Nut & Washer Tuerca y Arandela/ Roldana Écrou et Rondelle RP51503 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensa
PAGE 4
5 3 1 2 Maintenance If faucet exhibits very low flow: A. Remove and clean Aerator (1) with supplied wrench (2), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (5) is tightened securely with a wrench.* If faucet leaks from under handle: Remove handle and unthread trim cap (4). Using a wrench, ensure bonnet nut (5) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3).
PAGE 5
1 A. 2 1 2 1/2" (12.70mm) IPS B. 3 1 1 2 1 2 2 Supply Line Connections A. Position faucet (1) and gasket (2) on sink. Option: If sink is uneven, Note: Be careful when bending the copper tubing. Kinked tubes will void the warranty. Choose hook-ups for 1/2” I.P.S. connections: (1) Ball nose riser (3/8” O.D. copper tubing), or (2) 1/2” I.P.S. faucet connector. Use the enclosed coupling nuts (3) with the ball nose risers (1). Important: Use two wrenches when tightening. Do not overtighten.
PAGE 6
B. E. D. C. 1 SIL NE I CO 3 A. 1 2 3 2 3 2 1 1 1 F. G. 4 2 2 H. 5 4 3 2 1 5 1 2 3 2 1 6 Step 3b Metal Pop-Up Installation A. Remove stopper (1) and flange (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. G. Remove pivot nut (1). Install horizontal rod E. Pivot (1) must face faucet. Pull assembly (2) down firmly and hold in place. DO NOT TWIST. H.
PAGE 7
3 B. A. 4 1 3 1 2 3 2 2 1 D. IC SIL E ON C. 1 4 1 4 2 Grid Strainer Installation A. Remove grid flange (1). Screw nut and washer (2) down as far as possible. Push gasket (3) down to nut and washer. B. Remove tailpiece (1) and apply plumber tape (2) to threads. Replace tailpiece. Apply silicone sealant to underside of grid flange (1). Insert grid strainer assembly (2) up through C. bottom of lavatory. Screw grid flange back on and secure. D.
PAGE 8
5 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.