(Model 50-852, three phase) (Model 50-853, single phase) PART NO. 902108 - 06-27-02 Copyright © 2002 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). INSTRUCTION MANUAL 3 H.P.
GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result.
ADDITIONAL SAFETY RULES FOR DUST COLLECTORS WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. 1. DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions. 14. DO NOT use the dust collector as a toy. DO NOT use near or around children. 2. OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine. 15.
UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. 4 Fig.
ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. ASSEMBLING CASTER ASSEMBLIES TO BASE A C B Align the holes in caster assembly (A) Fig. 5, with four holes in support stand (B) located on the underside of base (C). Place a lockwasher (E) Fig. 5 onto a hex head screw (D), insert the hex head screw through the caster (A), and thread into hole in base (B).
4. Apply a bead of silicone sealant around flange of chute (F) Fig. 9. Align holes in ten-hole gasket (G) Fig. 9, with mounting holes in blower flange (F) and press gasket onto flange as shown. F G Fig. 9 5. Align mounting holes in dust chute (H) Fig. 10, with gasket (G), assembled in STEP 4. Place a lockwasher onto a hex head screw, insert screw through the chute and gasket, thread the screw into the motor assembly, and tighten securely. Repeat this process for the 9 remaining holes. Fig.
Fig. 13 H 7. Apply a bead of silicone sealant around flange of chute (H) Fig. 14. Align holes in eight-hole gasket (K) Fig. 14, with mounting holes in chute (H) and press gasket (K) onto flange as shown. K Fig. 14 8. Align mounting holes in left hand drum (N) Fig. 15, with gasket (K), assembled in STEP 7. Place a lockwasher onto a hex head screw, and insert screw through chute (H), thread screw into drum (N), and tighten securely as shown in Fig. 16. Repeat this process for the seven remaining holes.
11. Align two mounting holes in the top of drum support arm (T) Fig. 18, with two pre-drilled holes in drum (N) and fasten drum support arm (T) to drum (N). Place a lockwasher then a flat washer onto the hex head screw, insert the hex head screw through the hole in upper drum support and drum and thread a hex nut onto the hex head screw. NOTE: Do not completely tighten mounting hardware at this time. N T Fig. 18 12. Fasten the bottom of drum support (T) Fig. 19, at one corner of base (B).
ASSEMBLING FILTER AND DUST COLLECTION BAGS TO DRUM A B 1. Hook the loop on the top of filter bag (A) Fig. 22, onto filter bag support rod (B) as shown. 2. Assemble extension rod (C) Fig. 23, into the end of filter bag support rod (B). Raise support rods (B) and (C), with filter bag (A) attached and place end of extension support rod into holes of bracket (D). NOTE: Flared end of filter bag extension rod will prevent the rod from sliding through bracket. Fig. 22 B A C D Fig. 23 3. Insert band (F) Fig.
4. Pull up on each retaining clip (A) Fig. 26, and insert the dust collection bag (B) underneath each retaining clip to hold the dust collection bag in place. 5. Place the locking clamp (C) Fig. 26 around dust collection bag and dust collector drum and lock in place. A NOTE: Make certain locking clamp is positioned in the channel of the dust collector drum before locking clamp. C 6.
ASSEMBLING DUST INTAKE PORT TO BLOWER AND MOTOR ASSEMBLY B M A K E C E R TA I N T H E D U S T C O L L E C T O R I S DISCONNECTED FROM THE POWER SOURCE. 1. Align the four holes in the dust intake port (A) Fig. 29, with the mounting holes in the lip of flange (B) of blower assembly and fasten with four sheet metal screws (C). A C Fig. 29 2. Fig. 30, illustrates the dust intake ports assembled to the blower assembly. Fig. 30 3. Four dust intake port caps (D) Fig. 31, are supplied with the dust collector.
MODEL 50-852 THREE PHASE INSTALLATION B A Your dust collector is supplied with a motor and controller; however, it is not supplied with a power cord and plug. 1. To connect the dust collector to a power system, remove controller cover (A) Fig. 32. Fig. 32 2. Bring three phase power line through the access hole (B) Fig. 32, in the top of controller box and connect the three power lines to terminals (C) Fig. 33, and the green ground wire to ground screw (D). 3.
OPERATING CONTROLS ON/OFF SWITCH (Model 50-852) A The “on/off” switch is located on the side of the motor stand. To turn the dust collector “ON”, push button (A) Fig. 36. To turn the dust collector “OFF”, push button (B). B Fig. 36 ON/OFF SWITCH (Model 50-853) A The “on/off” switch is located on the side of the motor stand. To turn the dust collector “ON”, push button (A) Fig. 37. To turn the dust collector “OFF”, push button (B). B Fig.
NOTES 14
ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable · Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of your nearest supplier. WARNING: Since accessories, other than those offered by Delta, have not been tested with this product, use of such accessories could be hazardous. For safest operation, only Delta recommended accessories should be used with this product.
PORTER-CABLE • DELTA SERVICE CENTERS (CENTROS DE SERVICIO DE PORTER-CABLE • DELTA) Parts and Repair Service for Porter-Cable • Delta Machinery are Available at These Locations (Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable • Delta) ARIZONA Tempe 85282 (Phoenix) 2400 West Southern Avenue Suite 105 Phone: (602) 437-1200 Fax: (602) 437-2200 CALIFORNIA Ontario 91761 (Los Angeles) 3949A East Guasti Road Phone: (909) 390-5555 Fax: (909) 390-5554 San Leandro