Instructions / Assembly

ManualsBrandsDelta ManualsPortable Table Saws15 Amp 10 in. Table Saw with 30 in. Rip Capacity, Cast Iron Table and Extension Wings

1. Connect the two tube legs by inserting the end

of the left leg (A) into the end of the right leg (B)

as shown in Figure 1. Secure with a M8 x 70mm

carriage bolt, lock washer and nylock nut (153,

154, 155) and tighten.

2. Insert the four open ends of the tube legs into the

leg collars (C) as shown. Secure each leg with a M6

x 72mm bolt and nut (144, 145).

NOTE: One of the screw holes for the support panels is

designed to function as a grounding contact. This hole is

smaller than the other three holes.

FIGURE 1

Step 1: Stand

Use Hardware Bag “A”

36-5000 Quick

Assembly Guide

Step 2: Fixed Wheels and Stationary Feet

Use Hardware Bag “B”

1. Attach the two xed wheels (A) to the left leg,

opposite the pivot caster, using the M8 x 53 axle

pin and M8 Nylock nut (151, 155) as seen in Figure

2. Screw the adjustable feet (C) into the threaded

insets in the right leg next to the pivot caster.

3. Lay a scrap piece of 2x4 in back of the saw, as

shown in Figure 3, to prevent damage to the dust

chute when righting the saw.

4. Stand the saw right side up.

The machine is heavy, two

people are required to stand the

machine up.

5. Modify the two Adjustable Feet (C) by screwing

them in and out of the leg. The feet may be

adjusted to level the saw and locked in place by

tightening the M12 nut on the top. See Figure 2.

Read and Understand

Instruction Manual

Before Operation

FIGURE 2

FIGURE 3

Summary of content (4 pages)

PAGE 1
36-5000 Quick Assembly Guide Step 1: Stand Use Hardware Bag “A” B Read and Understand Instruction Manual Before Operation A 1. Connect the two tube legs by inserting the end of the left leg (A) into the end of the right leg (B) as shown in Figure 1. Secure with a M8 x 70mm carriage bolt, lock washer and nylock nut (153, 154, 155) and tighten. 2. Insert the four open ends of the tube legs into the C FIGURE 1 leg collars (C) as shown. Secure each leg with a M6 x 72mm bolt and nut (144, 145).
PAGE 2
Step 3: Front and Rear Rails - Use Hardware Bag “D” 1. Attach the front rail (1) to the table front using two (5/16-18 x 1 1/8”) flat head screws and two (5/16-18) hex flange nuts See Figure 4a. One conical star grounding-washer should be installed directly in front of one of the screw heads. See Figure 4b. Front Rail 1 4a 2. Attach the rear rail (2) to the table back using FIGURE 4 4b FRONT GAUGE BACK FIGURE 5 6a Rear Rail 2 FIGURE 6 two (5/16-18 x 7/8”) flat head screws with spring washers.
PAGE 3
Step 4: Extension Wings - Use Hardware Bag “C” For Models with Three Extension Wings 1. Attach the left side extension wing (3) to the front LEFT EXTENSION WING RIGHT EXTENSION WING 3 and rear rails using four (5/16-18 x 1 1/8”) flat head screws, four (5/16”) lock washers, and four (5/16-18) hex flange nuts. See Figure 9a. 2. Attach the left side extension wing (3) to side of RULER 3 the saw table using three (5/16-18 x 7/8”) hex head screws with spring washers. See Figure 9b. 3.
PAGE 4
Step 5: Wood Extension Table 52”rip capacity models only - Use Hardware Bag “E” 1. Lay the wood table (A) upside down on floor or bench. 2. Position legs (B) in corner as shown in Figure 7. The vertical wall of the angle plate on the leg should be against the end wood wall (C) of the table. 3. Carefully drill through the holes in the vertical angle plate holes and through the wood rail of the table with a ¼” drill.