(Model 23-665) PART NO. 900463 (011) Copyright © 2001 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, please call ESPAÑOL: PÁGINA 11 1-800-223-7278 (In Canada call 1-800-463-3582).
SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result.
ADDITIONAL SAFETY RULES FOR GRINDERS 1. DO NOT OPERATE your tool until it is completely assembled and installed according to the instructions. 15. STAND to one side of the wheel when turning on the power. 2. IF YOU ARE NOT thoroughly familiar with the operation of grinders, obtain advice from your supervisor, instructor or other qualified person. 16. AVOID awkward hand positions where a sudden slip could cause a hand to move into the grinding wheel. 17.
UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the carton. Remove the protective coating from all unpainted parts. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline, or lacquer thinner for this purpose). WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE TOOL TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU HAVE READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL.
HARDWARE ILLUSTRATION Hardware Illustrated in actual size 11/16" Flat Washer (2) 3/8" Lock Washer (2) 1/4 - 20 x 3/4" Carriage Head Screw (2) #10 - 24 x 1/2" Round Head Screw(4) 5/16" Lock Washer (2) 3/4" Flat Washer (4) #10 - 24 Hex Nut (4) 1/4 - 20 x 1/4" Hex Head Screw (2) 1/4 - 20 Hex Nut (2) 15/32" Flat Washer (4) 5/16 - 18 x 1/2" Hex Head Screw (2) 5/16 - 18 x 5/8" Hex Head Screw (2) Fig.
ASSEMBLY ASSEMBLING TOOL RESTS C 1. Assemble the v-grooved tool rest (A) Fig. 3, to the inside of the right wheel guard using two 5/16-18x5/8" hex head screws (B), and 3/4" flat washers (C). 2. Assemble the remaining flat surfaced tool rest (D) Fig. 3A, to the inside of the left wheel guard in the same manner using two 5/16-18x1/2" hex head screws (E), and 3/4" flat washers (C). A 3. Each tool rest is adjustable so that the edge (F) Fig.
2. Insert the short end of mounting rod (F) Fig. 7, into hole of frame (B) and fasten in place with 1/4-20x3/4" carriage head screw (G), 5/16” lock washer (H), and 1/420 hex nut (I). G H F B I Fig. 6 3. Assemble long end of eye shield mounting rod (F) Fig. 7, to the side of each wheel guard using bracket (J), 3/8" lockwasher and locking knob (L). The eye shield (A) is fully adjustable so it can be put in any position by moving the shield (A) or loosening locking knob (L) and repositioning rod (F).
1. All grounded, cord-connected tools: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. 2.
FLEXIBLE LAMP The flexible lamp operates independently of the grinder. To turn the lamp on and off, rotate switch (A) Fig. 12. WARNING: To reduce the risk of fire, use 50 watt or less, 120 volt, reflector track type light bulb (not supplied). A standard household light bulb should not be used. The reflector track type light bulb should not extend below the lamp shade. A Fig. 12 STARTING AND STOPPING GRINDER A The switch (A) Fig. 13, is located on the front of the grinder.
PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of PorterCable•Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278, (In Canada call 1-800-463-3582).