Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceKate Single-Handle Pull-Down Sprayer Kitchen Faucet in Stainless Featuring MagnaTite Docking

SINGLE LEVER LELAND

, VICTORIAN

, KATE

AND

LAKEVIEW™ PULL DOWN KITCHEN FAUCETS

PALANCA DESLIZABLE LELAND

, VICTORIAN

KATE

Y LAKEVIEW™ PARA LLAVES DE COCINA

ROBINETS MONOCOMMANDE LELAND

, VICTORIAN

KATE

ET LAKEVIEW

À BEC-DOUCHETTE

RÉTRACTABLE POUR ÉVIER DE CUISINE

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Models/Modelos/Modèles

955-DST, 955-SD-DST, 978-DST,

978-SD-DST, 978-WE-DST,

9955-DST, 9978-DST, 16955-SD-DST,

16970-SD-DST & 59963-SD-DST

Series/Series/Seria

SILICONE

Icons

11/18/15 Rev. C

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE

DEBE UTILIZAR CON MAQUINAS LAVAPLATOS PORTATILES! /

AVERTISSEMENT: ON NE DOIT PAS BRANCHER UN LAVE-VAISSELE

PORTATIF SUR CE ROBINET!

SILICONE

Icons

1/8"

73046

www.deltafaucet.com

Summary of content (16 pages)

PAGE 1
73046 SINGLE LEVER LELAND®, VICTORIAN®, KATE® AND LAKEVIEW™ PULL DOWN KITCHEN FAUCETS PALANCA DESLIZABLE LELAND®, VICTORIAN®, KATE® Y LAKEVIEW™ PARA LLAVES DE COCINA ROBINETS MONOCOMMANDE LELAND®, VICTORIAN®, KATE® ET LAKEVIEWMC À BEC-DOUCHETTE RÉTRACTABLE POUR ÉVIER DE CUISINE Models/Modelos/Modèles 955-DST, 955-SD-DST, 978-DST, 978-SD-DST, 978-WE-DST, 9955-DST, 9978-DST, 16955-SD-DST, 16970-SD-DST & 59963-SD-DST Series/Series/Seria Write purchased model number here.
PAGE 2
Limited Warranty on Delta® Faucets Replacement parts may be obtained by calling the applicable number below or by writing to: In the United States and Mexico: In Canada: Delta Faucet Company Masco Canada Limited, Plumbing Group Product Service Technical Service Centre 55 E. 111th Street 350 South Edgeware Road Indianapolis, IN 46280 St. Thomas, Ontario, Canada N5P 4L1 1-800-345-DELTA (3358) 1-800-345-DELTA (3358) customerservice@deltafaucet.com customerservice@mascocanada.
PAGE 3
1 2 3 * Front Frente Avant 3 2 1 4 2 1 4 1 5 6 Spout Installation Valve Assembly Installation NOTE: These faucets are designed to fit a maximum countertop thickness of 2 1/4". If you are installing the faucet on a Stainless Steel or a thin sink use RP37490 Stabilization Plate SUPPLIED WITH FAUCET. Note: Handle comes already installed on model 59963. Slide the gasket (1) up over tubes of valve assembly and place in groove in base (2).
PAGE 4
3 A-1 1 A-2 B. 7 3 4 1 2 1 A-3 Insert hose through spout tip only. A-4 7 1 7 4 4 3 8 1 1 5 7 8 1 6 5 1 Incorrect Installations. Instalacións incorrecta. Hose Installation A. Screw the threaded fitting of hose (1) into spray head (2) to prevent the hose from being pulled into the Installations incorrecte. spout until you are ready to flush the lines. Insert hose guide (3) into end of hose (1) as shown. Feed hose assembly (1) through spout (4) and hub (5).
PAGE 5
4 A. B. 2 2 OR 1 2 O 3 OU 1 4 3 1 2 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 6
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 7
5 6 5 3 6 5 1/8" 1 2 3 4 2 1 4 Soap Dispenser Installation Note: Soap dispenser not included with all models. Remove nut and gasket (1). Insert body (2) and gasket (3) through selected hole in sink. Make sure gasket (3) is properly seated in the base. Secure body to sink with nut and gasket (1). From under the sink screw the bottle (4) onto the body assembly shank. Insert pump and head (5) into body (2). Note: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz.
PAGE 8
7 3 4 2 2 3 1 Turn on hot and cold water supplies (1). Pull the hose assembly (2) out of the spout and remove the spray head (3). Be sure to hold the end of the hose down into the sink and turn faucet handle (4) to the mixed position. Flush water lines for one minute. IMPORTANT: This flushes away any debris that could cause damage to internal parts. Reinstall the spray head. Check all connections at arrows for leaks. Re-tighten if necessary, but do not overtighten.
PAGE 9
1/8" 4 5 1 3 2 Maintenance If faucet exhibits very low flow: A. Remove and clean Aerator (1) with supplied wrench (2), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). If faucet leaks from under handle: Remove handle and unthread trim cap (4). Using a wrench, ensure bonnet nut (5) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3). When reinstalling parts, make sure bonnet nut (5) is tightened securely with a wrench.
PAGE 10
MODELS / MODELOS / MODÈLES 978-DST, 978-SD-DST & 9978-DST RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP60734▲ 1.
PAGE 11
MODELS / MODELOS / MODÈLES 955-DST, 955-SD-DST, 9955-DST & 16955-SD-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP51464▲ RP47666 Set Screw Tornillo de Ajuste Vis de calage RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP50786▲ Button Cover Botón de la cubierta Bouton de couverture RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du be
PAGE 12
MODEL / MODELO / MODÈLE 16970-SD-DST RP54537▲ Spout Assembly with Magnet Ensamble del Tubo de Salida con Imán Bec avec Aimant RP51512▲ Handle w/Button & Set Screw Manija con botón y tornillo de presión Poignée avec bouton et vis de calage RP23093 Set Screw Tornillo de Ajuste Vis de calage RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP51511▲ Sprayer Assembly Ensamble de rociador Pulvérisateur RP51513▲ Red/Blue But
PAGE 13
MODEL / MODELO / MODÈLE 59963-SD-DST RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP73050▲ Handle w/Button & Set Screw Manija con botón y tornillo de presión Poignée avec bouton et vis de calage RP47666 Set Screw Tornillo de Ajuste Vis de calage RP54234▲ Red/Blue Button Botón rojo/azul Bouton rouge/bleu RP73049▲ Sprayer Assembly Ensamble de rociador Pulvérisateur RP73051▲ Sleeve Assembly Manja Manchon RP62875 Fr
PAGE 14
Notes / Notas / Notes 14 73046 Rev.
PAGE 15
Notes / Notas / Notes 15 73046 Rev.
PAGE 16
Notes / Notas / Notes 16 73046 Rev.