Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceSingle-Handle Pull-Down Kitchen Faucet with Soap Dispenser in Stainless Featuring MagnaTite Docking

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Models/Modelos/Modèles

989-DST, 999-DST,

4153-DST, 16961-DST,

16968-DST & 19950-DST

Series/Series/Seria

8/18/10 Rev. D

ASME A112.18.1 / CSA B125.1

MEETS OR EXCEEDS — ASME A112.18.1 / CSA B125.1

ALCANZA O EXCEDE LAS SIGIENTES NORMAS —

ASME A112.18.1 / CSA B125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE DEBE UTILIZAR

CON MAQUINAS LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF SUR CE ROBINET!

LE ROBINET EST CONFORME OU SUPÈRIEUR AUX EXIGENCES DES

NORMES SUIVANTES: ASME A112.18.1 / CSA B125.1

HIGH-RISE PULL-DOWN KITCHEN AND

BAR / PREP FAUCETS

LLAVES DE AGUA ELEVADAS, DESLIZABLES

HACIA ABAJO, PARA COCINAS Y BARES / PREP

ROBINET À COL DE CYGNE ET BEC-DOUCHETTE

POUR ÉVIER DE BAR OU D’ÎLOT DE CUISINE

1/8"

62817

Summary of content (16 pages)

PAGE 1
62817 UP C ® ASME A112.18.1 / CSA B125.1 HIGH-RISE PULL-DOWN KITCHEN AND BAR / PREP FAUCETS LLAVES DE AGUA ELEVADAS, DESLIZABLES HACIA ABAJO, PARA COCINAS Y BARES / PREP ROBINET À COL DE CYGNE ET BEC-DOUCHETTE POUR ÉVIER DE BAR OU D’ÎLOT DE CUISINE Models/Modelos/Modèles 989-DST, 999-DST, 4153-DST, 16961-DST, 16968-DST & 19950-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Backflow Protection System Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly.
PAGE 3
4 5 6 3 7 1 2 1 Maintenance If faucet exhibits very low flow A. Remove and clean aerator (1) (Note: some models require wrench (2) to remove aerator.), or B. (989 Series Only) Unscrew hose from spray head and clean debris from screen (the screen is located just inside the spray (3)). IMPORTANT: Reinstall screen to the spray head. (Failure to reinstall the screen could damage internal parts.) If faucet leaks from under handle: Remove handle (4) and cap (5).
PAGE 4
RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du bec & rondelle de frottement Models / Modelos / Modèles 989-DST & 999-DST ▲ Specify Finish Especifíque el Acabado Précisez le fini RP32529▲ Aerator Aireador Aérateur RP53101▲ (model 999) Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) RP47270▲ Lever Handle Manijas de Palanca Manette RP47667 Aerator Aireador Aérateur RP51502▲ Cap Casquete Embase RP51503 Bo
PAGE 5
RP62776▲ Set Screw & Button Tornillo de Presión y Botón Vis de calage et bouton Models / Modelos / Modèles 4153-DST RP62774▲ Sout Assembly Ensamble del Tubo de Salida Bec RP62775▲ Lever Handle Manijas de Palanca Manette RP62773▲ Sprayer Assembly Ensamble de rociador Pulvérisateur ▲ Specify Finish Especifíque el Acabado Précisez le fini RP51502▲ Cap Casquete Embase RP62777 Friction Spacers Arandela de Fricción Rondelle de frottement RP51503 Bonnet Bonete Chapeau RP50587 Valve Assembly Ensamble de la v
PAGE 6
RP49300▲ Set Screw & Button Tornillo de Presión y Botón Vis de calage et bouton Models / Modelos / Modèles 16961-DST RP53438▲ Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) ▲ Specify Finish Especifíque el Acabado Précisez le fini RP54731▲ Lever Handle Manijas de Palanca Manette RP51502▲ Cap Casquete Embase RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du bec & rondelle de frottement RP51503 Bonnet Bonet
PAGE 7
Models / Modelos / Modèles 16968-DST RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du bec & rondelle de frottement RP52140▲ Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) RP52610▲ Trim Ring, Base and Gasket Aro de Accesorio, Base y Empaque Anneau de finition, Embase et Joint RP50788 Gasket Only Sólo el Empaque Joint seulement RP52609 Mounting Bracket & Nut Abrazadera y Tuerca Fixation et écrou RP47888 P
PAGE 8
Model / Modelo / Modèle 19950-DST RP60934▲ Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) RP53879▲ Button Botón Bouton ▲ Specify Finish Especifíque el Acabado Précisez le fini RP54233 Set Screw Tornillo de Presión Vis de calage RP60937▲ Lever Handle Manijas de Palanca Manette RP51502▲ Cap Casquete Embase RP62875 Retainer Detenedor Arrêtoir RP51503 Bonnet Bonete Chapeau RP50815 Aerator & Wrench Aereador y Llave Aérateur et Clé RP50587 V
PAGE 9
Alternative Method Método Alternativa Méthode Alternative 1 3 3 2 2 4 2 1 5 4 2 INSTALLATION INSTRUCTIONS Your faucet is designed for a hole diameter of 1 3/8" +/- 1/8" (35 mm +/- 3 mm) and a deck thickness of up to 2 1/2" (64 mm). Insert hose guide (1) into end of hose (2) as shown. Feed hose assembly (2) through spout (3) and hub (4). Slide spout assembly onto hub. Use caution not to pinch fingers. Attach sprayer (5) to end of hose to keep hose in place.
PAGE 10
989-DST & 999-DST 2 16961-DST & 16968-DST 5 RP37490 (Not Included In All Models) RP37490 (Not Included In All Models) 3 6 1 3 7 2 4 4 32 8 2 3 1 1 9 4 All Models Models 16961-DST & 16968-DST Note: To improve stability on thin gage metal sinks, RP37490 thin deck aid (see illustration above) is available free of charge by calling 1-800-345-3358. Place gasket (1) into groove on bottom of base ring (2). Place base ring onto sink over mounting hole, then install trim ring (3) over base ring.
PAGE 11
Optional / Opcional / Facultative 19950-DST / 4153-DST 3 4 2 5 4 5 1 3 1 3 RP37490 (Not Included In All Models) 3 6 6 3 2 7 4 RP37490 (Not Included In All Models) 7 2 3 6 7 5 6 8 8 1 8 9 9 Optional Escutcheon Installation Model 19950-DST / 4153-DST Place gasket (1) into groove on bottom of base ring (2). Place base ring onto sink over mounting hole, then install trim ring (3) over base ring.
PAGE 12
3 A. B. 2 1 1 3 2 1 2 Hose Installation A. Slide hose weight (1) over end of hose (2). B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hose and outlet as shown. Pull down moderately to ensure connection has been made. Instalación De la Manguera A. Deslice la pesa de la manguera (1) sobre el extremo de la manguera (2). B. Deje pasar el extremo de la manguera (1) por la salida de la llave de agua / grifo (2). Fije el gancho (3) sobre la manguera y la salida como se muestra.
PAGE 13
4 A. B. OR 2 1 2 O 2 OU 3 1 3 4 2 1 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 14
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Do not install sleeve upside down. Ensure cut is straight. No instale la manga boca abajo. Asegúrese que el corte esté recto. N’installez pas le manchon à l’envers. Assurez-vous que la coupe est droite. Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1).
PAGE 15
5 2 6 B. A. 3 4 1 2 3 4 5 1 1 For Models with Soap Dispenser Remove the bottle (1). Separate head (2) from body assembly (3) by using a pulling and twisting motion. Make sure gasket (4) is properly seated in the base of the body assembly. Insert body assembly through selected hole in sink. Secure body assembly to sink with nut and gasket (5). From under the sink screw the bottle (1) onto the body assembly shank, then attach head assembly.
PAGE 16
7 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.