Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceSingle-Handle Pull-Down Kitchen Faucet with Soap Dispenser in Stainless Featuring MagnaTite Docking

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need

Usted puede necesitar

Articles dont vous pouvez avoir besoin:

Models/Modelos/Modèles

989-DST, 999-DST,

4153-DST, 16961-DST,

16968-DST & 19950-DST

Series/Series/Seria

SILICONE

Icons

11/18/15 Rev. G

WARNING: this faucet is not to be used with portable dishwashers!

ADVERTENCIA: ¡sesta llave no se debe utilizar con maquinas lavaplatos portatiles!

AVERTISSEMENT: on ne doit pas brancher un lave-vaissele portatif sur ce robinet!

HIGH-RISE PULL-DOWN KITCHEN AND

BAR / PREP FAUCETS

LLAVES DE AGUA CUELLO DE GANSO,

DESLIZABLES, PARA COCINAS Y BARES / PREP

ROBINET À COL DE CYGNE ET BEC-DOUCHETTE

POUR ÉVIER DE BAR OU D’ÎLOT DE CUISINE

1/8"

63235

www.deltafaucet.com

Para instalación fácil de su llave Delta usted necesitará:

• LEER TODAS las instrucciones completamente antes de empezar.

• LEER TODOS los avisos, cuidados, e información de mantenimiento.

For easy installation of your Delta faucet you will need:

• To READ ALL the instructions completely before beginning.

• To READ ALL warnings, care, and maintenance information.

Pour installer votre robinet Delta facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes les instructions

de nettoyage et d’entretien.

Backflow Protection System

Your Delta Faucet pull-out spout incorporates a backflow protection

system that has been tested to be in compliance with ASME A112.18.3

and ASME A112.18.1 / CSA B125.1. It incorporates two certified check

valves in series, which operate independently and are integral,

non-serviceable parts of the wand assembly.

Sistema de protección contra el contraflujo

Su llave de agua tipo deslizable Delta tiene un sistema de protección con-

tra el contraflujo, incorporado, que ha sido probado para cumplir con los

requisitos de ASME A112.18.3 y ASME A112.18.1 / CSA B125.1. Este

incorpora en la pieza de mano dos válvulas de retención o checadoras

certificadas en una serie, las cuales operan independientemente y son

piezas integrantes que no requieren servicio.

Dispositif anti-siphonnage

Le bec rétractable de votre robinet Delta comporte un dispositif

anti-siphonnage qui a été éprouvé et qui est conforme aux normes

ASME A112.18.3 et ASME A112.18.1 / CSA B125.1. Ce dispositif se

compose de deux clapets indépendants homologués, montés en série

dans le tube rigide, qui sont non réparables.

Summary of content (16 pages)

PAGE 1
HIGH-RISE PULL-DOWN KITCHEN AND BAR / PREP FAUCETS LLAVES DE AGUA CUELLO DE GANSO, DESLIZABLES, PARA COCINAS Y BARES / PREP ROBINET À COL DE CYGNE ET BEC-DOUCHETTE POUR ÉVIER DE BAR OU D’ÎLOT DE CUISINE 63235 Models/Modelos/Modèles 989-DST, 999-DST, 4153-DST, 16961-DST, 16968-DST & 19950-DST Series/Series/Seria ON You may need Usted puede necesitar TEF LON Articles dont vous pouvez avoir besoin: SI LIC WARNING: this faucet is not to be used with portable dishwashers! ADVERTENCIA: ¡sesta llave no se d
PAGE 2
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
4 5 6 3 7 1 2 1 Maintenance If faucet exhibits very low flow A. Remove and clean aerator (1) (Note: some models require wrench (2) to remove aerator.), or B. (989 Series Only) Unscrew hose from spray head and clean debris from screen (the screen is located just inside the spray (3)). IMPORTANT: Reinstall screen to the spray head. (Failure to reinstall the screen could damage internal parts.) If faucet leaks from under handle: Remove handle (4) and cap (5).
PAGE 4
Models / Modelos / Modèles 989-DST & 999-DST RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du bec & rondelle de frottement RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP47270▲ Lever Handle Manijas de Palanca Manette RP47667 Aerator Aireador Aérateur RP32529▲ Aerator Aireador Aérateur RP53101▲ (model 999) Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el ai
PAGE 5
Models / Modelos / Modèles 4153-DST RP62776▲ Set Screw & Button Tornillo de Presión y Botón Vis de calage et bouton RP62774▲ Spout Assembly Ensamble del Tubo de Salida Bec RP62775▲ Lever Handle Manijas de Palanca Manette RP62773▲ Sprayer Assembly Ensamble de rociador Pulvérisateur RP51503 Bonnet Bonete Chapeau ▲ Specify Finish Especifíque el Acabado Précisez le fini Thin Deck Aid Sostén para Bordes Delgados Plaque de renfort RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM A
PAGE 6
RP49300▲ Set Screw & Button Tornillo de Presión y Botón Vis de calage et bouton Models / Modelos / Modèles 16961-DST RP53438▲ Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) ▲ Specify Finish Especifíque el Acabado Précisez le fini RP54731▲ Lever Handle Manijas de Palanca Manette RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du bec & rondelle de frottement RP51503 Bonnet Bonete Chapeau RP50587 Valve Assem
PAGE 7
Models / Modelos / Modèles 16968-DST RP60923 Friction Spacers & Clip Aro para el Surtidor & Arandela de Fricción Anneau du bec & rondelle de frottement RP80977 Wand Retainer & Replacement Kit Soporte para el mango y piezas de repuesto Trousse de rechange et pièce de retenue de douchette RP52140▲ Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) RP52610▲ Trim Ring, Base and Gasket Aro de Accesorio, Base y Empaque Anneau de finition, Embase et Jo
PAGE 8
Model / Modelo / Modèle 19950-DST RP60934▲ Sprayer Assembly (includes aerator) Ensamble de rociador (incluye el aireador) Pulvérisateur (inclut aérateur) RP53879▲ Button Botón Bouton ▲ Specify Finish Especifíque el Acabado Précisez le fini RP54233 Set Screw Tornillo de Presión Vis de calage RP60937▲ Lever Handle Manijas de Palanca Manette RP51502▲ Cap Casquete Embase RP62875 Retainer Detenedor Arrêtoir RP51503 Bonnet Bonete Chapeau RP50815 Aerator & Wrench Aereador y Llave Aérateur et Clé RP37490 R
PAGE 9
1 989-DST & 999-DST 16961-DST & 16968-DST 5 RP37490 (Not Included In All Models) RP37490 (Not Included In All Models) 3 6 1 3 7 2 4 4 3 32 8 2 1 9 1 4 All Models Models 16961-DST & 16968-DST Note: To improve stability on thin gage metal sinks, RP37490 thin deck aid (see illustration above) is available free of charge by calling 1-800345-3358. Place gasket (1) into groove on bottom of base ring (2). Place base ring onto sink over mounting hole, then install trim ring (3) over base ring.
PAGE 10
Optional / Opcional / Facultative 19950-DST / 4153-DST 3 4 4 2 5 5 1 1 3 RP37490 (Not Included In All Models) 3 3 6 6 7 4 7 2 6 RP37490 (Not Included In All Models) 2 7 5 3 6 8 8 1 8 9 9 Optional Escutcheon Installation Model 19950-DST / 4153-DST Place gasket (1) into groove on bottom of base ring (2). Place base ring onto sink over mounting hole, then install trim ring (3) over base ring.
PAGE 11
2 A. C. D. 1 4 4 2 1 5 B. 3 5 4 Insert hose through spout tip only. Inserte la manguera solo a través de la punta del surtidor. 1 Introduisez le tuyau souple dans l’extrémité du bec seulement. 1 Hose Installation A. Screw the threaded fitting of hose (1) into spray head (2) to prevent the C. Feed hose assembly (1) through spout (4) and hub (5). B. Insert hose guide (3) into end of hose (1) as shown. D. Slide spout assembly onto hub. Use caution not to pinch fingers.
PAGE 12
3 A. B. 2 1 3 1 2 2 1 2 3 1 Hose Installation A. Slide hose weight (1) over end of hose (2). B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hose and outlet as shown. Pull down moderately to ensure connection has been made. Instalación De la Manguera A. Deslice la pesa de la manguera (1) sobre el extremo de la manguera (2). B. Deje pasar el extremo de la manguera (1) por la salida de la llave de agua / grifo (2). Fije el gancho (3) sobre la manguera y la salida como se muestra.
PAGE 13
4 A. B. OR 2 2 1 O 2 OU 3 1 3 4 2 1 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 14
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 15
5 2 6 B. A. 3 4 1 2 3 4 5 1 1 For Models with Soap Dispenser Remove the bottle (1). Separate head (2) from body assembly (3) by using a pulling and twisting motion. Make sure gasket (4) is properly seated in the base of the body assembly. Insert body assembly through selected hole in sink. Secure body assembly to sink with nut and gasket (5). From under the sink screw the bottle (1) onto the body assembly shank, then attach head assembly.
PAGE 16
7 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.