Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceGrant Single-Handle Pull-Out Sprayer Kitchen Faucet in Stainless

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODASlasinstruccionescompletamente

antesdeempezar.

•LEER TODOSlosavisos,cuidados,e

informacióndemantenimiento.

For easy installation of your Delta

faucet you will need:

•ToREAD ALLtheinstructionscompletely

beforebeginning.

•ToREAD ALLwarnings,care,andmaintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTESlesinstructionsavantdedébuter;

•LIRE TOUSlesavertissementsainsiquetoutes

lesinstructionsdenettoyageetd’entretien.

Models/Modelos/Modèles

16953-DST

Series/Series/Seria

SILICONE

Icons

6/09/15   Rev.C

MEETSOREXCEEDS—ASMEA112.18.1/CSAB125.1

ALCANZAOEXCEDELASSIGIENTESNORMAS—

ASMEA112.18.1/CSAB125.1

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE

DEBE UTILIZAR CON MAQUINAS LAVAPLATOS PORTATILES! /

AVERTISSEMENT: ONNEDOITPASBRANCHERUNLAVE-VAISSELE

PORTATIFSURCEROBINET!

LEROBINETESTCONFORMEOUSUPÈRIEURAUXEXIGENCESDES

NORMESSUIVANTES:ASMEA112.18.1/CSAB125.1

1/8"

SINGLE HANDLE PULLOUT KITCHEN FAUCET

LLAVES EXTRAÍBLES DE AGUA PARA COCINAS

ROBINETS À UNE MANETTE À BEC-DOUCHETTE

RÉTRACTABLE POUR ÉVIERS DE CUISINE

SILICONE

Icons

70727

www.deltafaucet.com

Summary of content (12 pages)

PAGE 1
70727 SINGLE HANDLE PULLOUT KITCHEN FAUCET LLAVES EXTRAÍBLES DE AGUA PARA COCINAS ROBINETS À UNE MANETTE À BEC-DOUCHETTE RÉTRACTABLE POUR ÉVIERS DE CUISINE Models/Modelos/Modèles 16953-DST Series/Series/Seria ON You may need/Usted puede necesitar/ Articles dont vous pouvez avoir besoin: TEF LON SI LIC WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE D I S H WA S H E R S ! / A DV E RT E N C I A : ¡ S E S TA L L AV E N O S E DEBE UTILIZAR CON MAQUINAS LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE D
PAGE 2
Limited Warranty on Delta® Faucets Parts and Finish All parts (other than electronic parts and batteries) and finishes of this Delta® faucet are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed or, for commercial users, for 5 years from the date of purchase.
PAGE 3
1 B. A. C. A. 1 2 1 B. 3 1 2 3 1 1 3 1 2 2 2 2 Faucet Installation Faucet Installation DECK MOUNT STYLE A. Place baseplate shanks (1) through mounting holes in deck. Option: If sink is uneven, use silicone sealant under the baseplate. CENTER MOUNT STYLE C. Secure faucet to sink with mounting nut and washer (1). Tighten securely by hand. Using a Phillips screwdriver, tighten locking screws (2). Install locknuts (3) and hand-tighten. A. Install round escutcheon (1) onto faucet (2).
PAGE 4
2 B. A. Side View Vista Lateral Vue de Côté 3 2 1 3 2 2 1 4 3 2 1 1 3 3 1 Hose Installation Incorrect Installations. Instalacións incorrecta. A. Pass hose (1) through faucet (2). Thread wand assembly (3) onto hose (1) to prevent it from becoming lodged in faucet when installing weight (4). Slide hose weight (4) over other end of hose. Installations incorrecte. B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hose and outlet as shown.
PAGE 5
3 B. A. 2 OR 2 1 O 2 OU 3 1 3 4 1 2 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 6
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 7
4 B. A. 3 4 2 1 A. Turn on hot and cold water supplies (1). Pull the hose assembly (2) out of the spout and remove the spray wand (3). Be sure to hold the end of the hose down into the sink and turn faucet handle (4) to the mixed position. Flush water lines for one minute. IMPORTANT: This flushes away any debris that could cause damage to internal parts. B. Reinstall the spray wand. Check all connections at arrows for leaks.
PAGE 8
5 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 9
Backflow Protection System Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly.
PAGE 10
RP70739▲ Lever Handle Assembly Manijas de Palanca Manette RP47666 Set Screw Tornillo de Presión Vis de calage RP70738s Wand Assembly Ensamble de la Cabeza del Rociador Bec-douchette RP47271 Button / Botón / Bouton RP51502▲ Cap Casquillo Embase RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM RP51503 Adaptadors Bonnet & V-Ring 3/8”-24 UNEF a 1/2”-20 UN & Bonete y Aro-V Chapeau et Joint à lèvres 3/8”-24 UNEF a 1/2”-14 NPSM Adapteurs 3/8 po-24 UNEF à 1/2 po-20 UN et 3/8 po-24 UNEF
PAGE 11
Notes / Notas / Notes 11 70727 Rev.
PAGE 12
Notes / Notas / Notes 12 70727 Rev.