Installation Guide

ManualsBrandsDelta ManualsKitchenKessler Chrome 1-Handle Deck Mount Pull-Out Kitchen Faucet (Deck Plate Included)

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Models/Modelos/Modèles

468-SD-DST, 16926-SD-DST,

16927-SD-DST, 16929-SD-DST &

16932-SD-DST

Series/Series/Seria

8/27/15 Rev. B

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS! / ADVERTENCIA: ¡SESTA LLAVE NO SE DEBE UTILIZAR

CON MAQUINAS LAVAPLATOS PORTATILES! / AVERTISSEMENT: ON NE

DOIT PAS BRANCHER UN LAVE-VAISSELE PORTATIF SUR CE ROBINET!

SINGLE HANDLE PULLOUT KESSLER

™

DEBONAIR

LEWISTON

AND CICERO

KITCHEN FAUCETS

LLAVES EXTRAÍBLES DE AGUA PARA COCINAS

KESSLER

™

DEBONAIR

, LEWISTON

Y CICERO

ROBINETS À UNE MANETTE À BEC-DOUCHETTE

RÉTRACTABLE KESSLER

™

DEBONAIR

, LEWISTON

ET CICERO

POUR ÉVIERS DE CUISINE

1/8"

73040

Summary of content (12 pages)

PAGE 1
73040 SINGLE HANDLE PULLOUT KESSLER™, DEBONAIR®, LEWISTON® AND CICERO® KITCHEN FAUCETS LLAVES EXTRAÍBLES DE AGUA PARA COCINAS KESSLER™, DEBONAIR®, LEWISTON® Y CICERO® ROBINETS À UNE MANETTE À BEC-DOUCHETTE RÉTRACTABLE KESSLER™, DEBONAIR®, LEWISTON® ET CICERO® POUR ÉVIERS DE CUISINE Models/Modelos/Modèles 468-SD-DST, 16926-SD-DST, 16927-SD-DST, 16929-SD-DST & 16932-SD-DST Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Backflow Protection System Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly. LIFETIME FAUCET AND FINISH LIMITED WARRANTY INCURRED IN INSTALLATION, REPAIR, OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGES ARE EXCLUDED.
PAGE 3
1 B. A. C. A. 1 2 1 B. 3 1 2 3 3 1 1 1 2 2 2 2 Faucet Installation Faucet Installation DECK MOUNT STYLE A. Place baseplate shanks (1) through mounting holes in deck. Option: If sink is uneven, use silicone sealant under the baseplate. CENTER MOUNT STYLE C. Secure faucet to sink with mounting nut and washer (1). Tighten securely by hand. Using a Phillips screwdriver, tighten locking screws (2). Install locknuts (3) and hand-tighten. A. Install round escutcheon (1) onto faucet (2).
PAGE 4
2 B. A. Side View Vista Lateral Vue de Côté 3 2 1 3 2 2 1 3 4 2 1 1 3 3 1 Incorrect Installations. Hose Installation A. Pass hose (1) through faucet (2). Thread wand assembly (3) onto hose (1) to prevent it from becoming lodged in faucet when installing weight (4). Slide hose weight (4) over other end of hose. B. Push hose end (1) onto faucet outlet (2). Attach clip (3) over hose and outlet as shown. Pull down moderately to ensure connection has been made. Instalacións incorrecta.
PAGE 5
3 B. A. 2 OR 2 1 O 2 OU 3 1 3 4 1 2 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 6
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 7
4 5 2 A. B. 3 4 6 2 3 4 1 5 1 Soap Dispenser Installation Remove nut (1). Separate head (2) from body (3). Insert body (3) and gasket (4) through selected hole in sink. Make sure gasket (4) is properly seated in the base. Secure body to sink with nut (1). From under the sink screw the bottle (5) onto the body assembly shank. Insert pump (6) into head (2), then drop into body (3). NOTE: To fill, lift the head and pump assembly out of the bottle and pour not more than 8 oz. into bottle.
PAGE 8
6 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 9
For All Models Para todos los modelos Pour tous les modèles 1/8" 1 2 3 RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM Adaptadors 3/8”-24 UNEF a 1/2”-20 UN & 3/8”-24 UNEF a 1/2”-14 NPSM Adapteurs 3/8 po-24 UNEF à 1/2 po-20 UN et 3/8 po-24 UNEF à 1/2 po-14 NPSM Maintenance If faucet leaks from under handle: Remove handle and unthread trim cap (1). Using a wrench, ensure bonnet nut (2) is tight. If leak persists–SHUT OFF WATER SUPPLIES. Replace valve cartridge (3).
PAGE 10
73040 Rev.
PAGE 11
73040 Rev.
PAGE 12
73040 Rev.