Installation Instructions

ManualsBrandsDelta ManualsPlumbing Product140-WE-DST

SINGLE HANDLE KITCHEN FAUCET

LLAVE DE COCINA DE PALANCA

ROBINET DE CUISINE À UNE MANETTE

Models/Modelos/Modèles

140-DST, 141-DST, 340-DST,

440-DST & 441-DST

Series/Series/Seria

Para instalación fácil de su llave

Delta usted necesitará:

sLEER TODAS las instrucciones

completamente antes de empezar.

sLEER TODOS los avisos, cuidados,

e información de mantenimiento.

For easy installation of your

Delta faucet you will need:

s4OREAD ALL the instructions completely

before beginning.

s4OREAD ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

SILICONE

Pour installer votre robinet

Delta facilement, vous devez:

sLIRE TOUTES les instructions avant

de débuter;

sLIRE TOUS les avertissements ainsi que

toutes les instructions de nettoyage et

d’entretien;

52289 52289 52289 52289 52289 52289

11/1/08 Rev. B

ASME A112.18.1 / CSA B125.1

Summary of content (12 pages)

PAGE 1
UP C ® 52289 s 4O READ ALL the instructions completely before beginning. s 4O READ ALL warnings, care, and maintenance information. 52289 52289 52289 You may need/Usted puede necesitar/ Articles dont vous pouvez avoir besoin: For easy installation of your Delta faucet you will need: E 52289 Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
LIFETIME FAUCET AND FINISH LIMITED WARRANTY All parts and finishes of the Delta® faucet are warranted to the original consumer purchaser to be free from defects in material & workmanship for as long as the original consumer purchaser owns their home. Delta Faucet Company recommends using a professional plumber for all installation & repair.
PAGE 3
RP54233S Set Screw Tornillo de Ajuste Vis de Calage RP54232S Handle w/Button & Set Screw Manija con Botón y Tornillo de Ajuste Manette avec Bouton et Vis de Calage RP54234 Red/Blue Button Botón: Rojo/Azul Bouton-Rouge/Bleu RP51502S Cap Casquillo Embase RP47029 Mounting Bracket Soporte de Montaje Support de montage RP51503 Bonnet & V-Ring Bonete y Aro-V Chapeau et Joint à lèvres RP47030 Nut and Wrench Tuerca y Llave Ècrou et rondelle RP50587 Valve Assembly Ensamble de la válvula Soupape RP18508S 2.
PAGE 4
1 340 Series 140 Series A. 340 Series B. 2 2 2 2 1 1 1 140 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Feed tubes (1) down through center hole in sink. Secure faucet to sink with mounting nuts (2) supplied with your faucet. OPTION: If sink is uneven, use silicone sealant under the gasket. Continue to step 3. 140 Serie 340 Series A. SHUT OFF WATER SUPPLIES. Remove old faucet. Feed tubes (1) down through center hole in sink. OPTION: If sink is uneven, use silicone sealant under the gasket.
PAGE 5
440 Series 440 Series A. B. 2 2 3 1 2 1 440 Series A. SHUT OFF WATER SUPPLIES. Remove old faucet. Feed tubes (1) down through center hole in sink. Secure faucet to sink with mounting nuts (2) supplied with your faucet. OPTION: If sink is uneven, use silicone sealant under the gasket. B. Mount the spray support (1) in far right hole in sink. Hand tighten nut (2). Insert spray hose (3) down through support assembly. Continue to step 2. B.
PAGE 6
141 Series 441 Series 441 Series A. B. 1 1 3 1 2 2 2 3 3 4 4 2 141 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Make sure gasket and base (1) are properly positioned under new faucet. Feed tubes and shank (2) down through hole in sink. Secure faucet to sink with bracket (3), using nut and wrench (4) supplied with your faucet. OPTION: If sink is uneven, use silicone sealant under the gasket. Continue to step 3. 141 Serie CIERRE LOS SUMINISTROS DE AGUA. Quite la llave vieja.
PAGE 7
B. A. 2 3 3 1 1 3 2 2 2 1 For Sprayer Models Only A. Pull on clip (1) until disengaged. Pull down on diverter plug (2) to remove. Discard diverter plug. Caution: Do not remove tube clip (3). B. Keeping clip (1) disengaged, insert diverter hose end (2) into diverter housing (3) until seated. Push in clip (1) until it snaps. Pull down moderately to ensure connection has been made. Para el rociador modela solamente A. Hale el sujetador o gancho (1) hasta que se desencaje.
PAGE 8
3 A. B. 2 OR 2 1 O 2 OU 3 1 3 4 2 1 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 9
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet ﬁtting (4).
PAGE 10
4 A. B. 2 1 3 FLUSH YOUR SYSTEM: A. Remove aerator (1) and turn faucet handle (2) to the full on mixed position. Turn on hot and cold water supplies (3) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. Reinstall aerator. B. Check all connections at arrows for leaks. Re-tighten if necessary, but do not overtighten. B. Examíne si hay filtraciones en todas las conexiones indicadas con flechas.
PAGE 11
5 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”).
PAGE 12
4 3 2 1 5 Maintenance If faucet exhibits very low flow: A. Remove and clean Aerator (1), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (2). When reinstalling parts, make sure bonnet nut (3) is tightened securely with a wrench.* If spray attachment does not function properly: Replace diverter and hose assembly (5). If faucet leaks from under handle: Remove handle and unthread trim cap (4). Using a wrench, ensure bonnet nut (3) is tight.