Installation Guide

ManualsBrandsDelta ManualsKitchen ApplianceClassic Single-Handle Kitchen Faucet in Chrome

SINGLE HANDLE KITCHEN FAUCET

LLAVE DE COCINA DE PALANCA

ROBINET DE CUISINE À UNE MANETTE

Models/Modelos/Modèles

100-DST, 101-DST, 175-DST,

300-DST, 400-DST, 100-DST-A,

300-DST-A, 400-DST-A,

100-BH-DST, 300-BH-DST,

400-BH-DST & 400-DST-L

Series/Series/Seria

Para instalación fácil de su llave

Delta usted necesitará:

•LEER TODAS las instrucciones

completamente antes de empezar.

•LEER TODOS los avisos, cuidados,

e información de mantenimiento.

For easy installation of your

Delta faucet you will need:

•ToREAD ALL the instructions completely

before beginning.

•ToREAD ALL warnings, care, and

maintenance information.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

SILICONE

Icons

SILICONE

Icons

SILICONE

Icons

Pour installer votre robinet

Delta facilement, vous devez:

•LIRE TOUTES les instructions avant

de débuter;

•LIRE TOUS les avertissements ainsi que

toutes les instructions de nettoyage et

d’entretien;

3/15/10 Rev. B

ASME A112.18.1 / CSA B125.1

62766

Summary of content (12 pages)

PAGE 1
SINGLE HANDLE KITCHEN FAUCET 62766 LLAVE DE COCINA DE PALANCA ROBINET DE CUISINE À UNE MANETTE ® UP C ® ASME A112.18.1 / CSA B125.1 Models/Modelos/Modèles 100-DST, 101-DST, 175-DST, 300-DST, 400-DST, 100-DST-A, 300-DST-A, 400-DST-A, 100-BH-DST, 300-BH-DST, 400-BH-DST & 400-DST-L Series/Series/Seria Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
Lifetime Faucet and Finish Limited Warranty the original consumer purchaser must be made available to Delta for all warranty claims. THIS IS THE EXCLUSIVE WARRANTY BY DELTA FAUCET COMPANY, WHICH DOES NOT MAKE ANY OTHER WARRANTY OF ANY KIND, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY.
PAGE 3
RP60095▲ Handle with Set Screw Manija con Tornillo de Ajuste Manette avec Vis de Calage RP54233▲ Set Screw Tornillo de Ajuste Vis de Calage RP54236▲ Escutcheon, Spacer & Gasket Chapetón, Separadore y Empaque Boîtier, Pièce D’espacement et Joint RP28970▲ Handle with Set Screw Manija con Tornillo de Ajuste Manette avec Vis de Calage RP28906 Red/Blue Button Botón rojo/azul Bouton rouge/bleu RP51502▲ Cap Casquillo Embase RP2393 Handle with Set Screw Manija con Tornillo de Ajuste Manette avec Vis de Calage
PAGE 4
1 300 Series 100 Series A. 300 Series B. 2 2 2 2 1 1 1 100 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Feed tubes (1) down through center hole in sink. Secure faucet to sink with mounting nuts (2) supplied with your faucet. OPTION: If sink is uneven, use silicone sealant under the gasket. Continue to step 3. 100 Serie 300 Series A. SHUT OFF WATER SUPPLIES. Remove old faucet. Feed tubes (1) down through center hole in sink. OPTION: If sink is uneven, use silicone sealant under the gasket.
PAGE 5
400 Series 400 Series A. B. 2 2 3 1 2 1 400 Series A. SHUT OFF WATER SUPPLIES. Remove old faucet. Feed tubes (1) down through center hole in sink. Secure faucet to sink with mounting nuts (2) supplied with your faucet. OPTION: If sink is uneven, use silicone sealant under the gasket. B. Mount the spray support (1) in far right hole in sink. Hand tighten nut (2). Insert spray hose (3) down through support assembly. Continue to step 2. B.
PAGE 6
101 Series 175 Series 175 Series A. 1 B. 1 3 2 2 1 2 3 3 4 4 2 101 Series SHUT OFF WATER SUPPLIES. Remove old faucet. Make sure base, spacer and gasket (1) are properly positioned under new faucet. Feed tubes and shank (2) down through mounting hole. Secure to sink with bracket (3), using nut and wrench (4) supplied with your faucet. OPTION: If sink is uneven, use silicone sealant under the gasket. Continue to step 3. 2 175 Series A. SHUT OFF WATER SUPPLIES. Remove old faucet.
PAGE 7
B. A. 2 3 3 1 1 3 2 2 2 1 For Sprayer Models Only A. Pull on clip (1) until disengaged. Pull down on diverter plug (2) to remove. Discard diverter plug. Caution: Do not remove tube clip (3). B. Keeping clip (1) disengaged, insert diverter hose end (2) into diverter housing (3) until seated. Push in clip (1) until it snaps. Pull down moderately to ensure connection has been made. Para el rociador modela solamente A. Hale el sujetador o gancho (1) hasta que se desencaje.
PAGE 8
3 A. B. 2 OR 2 1 O 2 OU 3 1 3 4 2 1 4 Water Line Connections A. Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 9
Incorrect Installation Instalación Incorrecta Installation Incorrecte Correct method Método Correcto Bonne méthode 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 10
4 A. B. 2 1 3 FLUSH YOUR SYSTEM: A. Remove aerator (1) and turn faucet handle (2) to the full on mixed position. Turn on hot and cold water supplies (3) and flush water lines for one minute. Important: This flushes away any debris that could cause damage to internal parts. Reinstall aerator. B. Check all connections at arrows for leaks. Re-tighten if necessary, but do not overtighten. B. Examíne si hay filtraciones en todas las conexiones indicadas con flechas.
PAGE 11
5 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”).
PAGE 12
3 4 2 1 5 Maintenance If faucet exhibits very low flow: A. Remove and clean Aerator (1), or B. SHUT OFF WATER SUPPLIES. Replace valve cartridge (2). When reinstalling parts, make sure bonnet nut (4) is tightened securely with a wrench.* If spray attachment does not function properly: Replace diverter and hose assembly (5). If faucet leaks from under handle: Remove handle and unthread trim cap (3). Using a wrench, ensure bonnet nut (4) is tight. Note: Do not attempt to disassemble cartridge (2).