User's Manual

ManualsBrandsDelta Systems ManualsElectronics915 MHz REMOTE CONTROL RECEIVER

EnclosurE rating: ElEctrical rating: Fcc PEnding

NEMA 3, 3R, 12, 13 115/230 VAC, 24 FLA, 60 Hz ic PEnding

Etl PEnding

Wiring diagraM:

Overload protection is not provided. Do not use oversized circuit protection. Use 3/4" conduit only. Grounding between conduit is not

automatic – it must be provided upon installation. The control box comes from the factory wired for 115 VAC only. Remove white jumper for

230 VAC operation. Excessively long electrical runs should be wired at 230 VAC. Green or bare wires must only be used for ground. It is

unsafe to use a ground as a neutral. Use of the wrong wire size could damage the motors and/or control box. Read the Installation

Instructions carefully prior to installation. Read the operating instructions carefully before attempting to use.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED

MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

• The control box should only be installed by a licensed electrician.

• caution/aVErtissEMEnt/cuidado: Hazardous voltage will cause severe injury or death. Disconnect from

power supply before servicing!

• caution/aVErtissEMEnt/cuidado: Risk of electric shock! More than one disconnect switch may be

required to de-energize the equipment before servicing!

• dangEr/dangEr/PEligro: Hazardous voltage! Ensure that main power is shut off (disconnected) prior to

connecting any wires to the terminal blocks!

• Non-metallic enclosure does not provide grounding between conduit connections. Use grounding bushings

and jumper wires.

• The opening of the branch-circuit protective device may be an indication that a fault current has been interrupted.

To reduce the risk of ﬁre or electric shock, current-carrying parts and other components of the controller

should be examined and replaced if damaged.

• Use 30-amp overload protection (refer to all applicable re, electrical and/or building codes for type of device).

• Do not use oversized circuit protection.

• Use copper conductors only.

installation instructions:

1. To raise the lift, press and hold the UP button on the front panel or on the handheld remote. Release the

UP button when the lift is at the desired position.

2. To lower the lift, press and hold the DOWN button on the front panel or on the handheld remote. Release

the DOWN button when the lift is at the desired position.

3. There is an approximate 3 second delay when switching directions from UP to DOWN or from DOWN to U P.

1. Press and hold the LEVEL switch on the front panel. This will turn Motor #1 off. See wiring diagram.

2. While holding the LEVEL switch down, use the manual UP or DOWN switches to level the boat lift.

3. When the boat lift is level, release the UP or DOWN switch, and then release the LEVEL switch.

1. Press and release the AUTO STOP button on the front panel of the control box to turn this

feature on and off.

2. When the AUTO STOP feature is on, press and release the UP or DOWN button on the front panel, or on

the remote, to start the boat lift moving.

3. The boat lift will continue to raise or lower until it activates one of the limit switches. In addition, the

boat lift will stop when the AUTO STOP button on the front panel or the STOP button on the handheld

remote is pressed.

1. Press and release the AUXILIARY button on the front panel or the AUX button on the handheld remote

to turn the auxiliary device on for approximately 10 minutes. To turn the auxiliary device off, press and

release the AUXILIARY button on the front panel or the AUX button on the handheld remote.

2. Press and hold the AUXILIARY button on the front panel or the AUX button on the handheld remote for

three seconds to turn the auxiliary device on indeﬁnitely. To turn the auxiliary device off, press and

release the AUXILIARY button on the front panel or the AUX button on the handheld remote.

1. Press and hold the STOP button on the handheld remote. Press and hold the LEARN/CLEAR button on

the front panel for three seconds, then release the LEARN/CLEAR button.

2. Continue to press the STOP button on the handheld remote for one more second, then release the

STOP button. The handheld remote should now operate the boat lift.

3. Test the handheld remote to ensure proper function.

4. If another handheld remote is accidentally learned to the control box, press and hold the

LEARN/CLEAR button on the front cover for ten seconds. To operate the lift, any handheld remotes will

have to be reprogrammed to the control box by following Steps 1-4.

5. Spare and replacement handheld remotes can be purchased from your distributor.

1. Remove all four screws from the back of the handheld remote

2. Remove the back plastic cover

3. Remove the battery from the holder

4. Insert one 3-volt, CR2032 battery into the holder. caution/aVErtissEMEnt/cuidado: ENSURE

PROPER POLARITY OR THE HANDHELD REMOTE WILL NOT FUNCTION.

5. Re-install the back plastic cover

6. Re-install the four screws. caution/aVErtissEMEnt/cuidado: DO NOT OVER TIGHTEN!

Over tightening will strip the holes in the mating plastic cover.

raisE and loWEr

thE liFt

lEVEl thE liFt

using thE

auto-stoP

FEaturE

WARNING

AVERTISSEMENT/ADVERTENCIA:

Prior to use, ensure proper

function and position of

limit switches.

rEPlacing a

battEry in

thE handhEld

rEMotE

using thE

auxiliary dEVicEs

(iF installEd)

The auxiliary out provides

5 amps max. at 115 VAC.

PrograMMing

thE handhEld

rEMotE

WARNING

AVERTISSEMENT/ADVERTENCIA:

Ensure that no one else

in the vicinity is operating a

wireless device. If someone

else in the vicinity is

operating a wireless device,

it could be learned to the

control box during

this operation.

CONTROL BOX FOR A TWO MOTOR BOAT LIFT

INSTALLATION INSTRUCTIONS

CONTROL BOX FOR A TWO MOTOR BOAT LIFT

OPERATING INSTRUCTIONS

Control boxes and handheld remotes are proudly manufactured in the USA.

N/C

GROUND

NEUTRAL

INPUT

POWER

WHITE JUMPER WIRE FOR 115V OPERATION

USE COPPER CONDUCTORS ONLY

DANGER/PELIGRO

HAZARDOUS VOLTAGE

ENSURE THAT MAIN POWER IS SHUT OFF

(DISCONNECTED) PRIOR TO CONNECTING

ANY WIRES TO THESE TERMINAL BLOCKS!

MOTOR

#1 OUT

AUX

OUT

UPPER

LIMIT

LOWER

LIMIT

RISK OF ELECTRIC SHOCK

MORE THAN ONE

DISCONNECT SWITCH MAY

BE REQUIRED TO DE-ENERGIZE

EQUIPMENT BEFORE

SERVICING

NONMETALLIC ENCLOSURE

DOES NOT PROVIDE

GROUNDING BETWEEN

CONDUIT CONNECTION USE

GROUNDING BUSHINGS AND

JUMPER WIRES

ELECTRICAL RATING:

115/230 VAC, 24 FLA, 60 Hz

WIRING CLAMPING

TORQUE REQUIREMENTS

NTRL BUS BAR - 14 IN-LB

GND BUS BAR - 14 IN-LB

8-POS TERM STRIP - 7.0 IN-LB

6-POS TERM STRIP - 4.4 IN-LB

SEE INSTALLATION

INSTRUCTIONS FOR PROPER

ELECTRICAL CONNECTIONS

MOTOR

#2 OUT

AUX GND

AUX NTRL

MTR#2 NTRL

MTR#1 NTRL

BLK

RED

N/C

ORG

RED

BLK

MTR#2 GND

MTR#1 GND

CAUTION

AVERTISSEMENT/CUIDADO

N/C

COM

TB1 TB2

Summary of content (2 pages)

PAGE 1
CONTROL BOX FOR A TWO MOTOR BOAT LIFT CONTROL BOX FOR A TWO MOTOR BOAT LIFT OPERATING INSTRUCTIONS INSTALLATION INSTRUCTIONS AVERTISSEMENT/ADVERTENCIA: Prior to use, ensure proper function and position of limit switches. using the auxiliary devices (if installed) 3. 1. 2. The auxiliary out provides 5 amps max. at 115 VAC. When the AUTO STOP feature is on, press and release the UP or DOWN button on the front panel, or on the remote, to start the boat lift moving.
PAGE 2
CONTROL BOX FOR A TWO MOTOR BOAT LIFT CONTROL BOX FOR A TWO MOTOR BOAT LIFT INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Mount the Box 115 VAC Input Power Hook-up NOTE: If using 230 VAC input power, skip Steps 4-11 and proceed to Steps 12-21. 1. Mount the control box vertically to a well-supported structure. The enclosure door hinge should be on the left side when facing the control box. 2.