HB97 Product Specification 802.11n/g 2.4GHz (2x2) WLAN PCI Express MiniCard Adapter Note: This document contains proprietary technical information in which is the property of the Delta Networks Inc. and shall not be disclosed to others in whole or in part, reproduced, copied, or used as the basis for design, manufacturing, or sale of apparatus without written permission of Delta Networks Inc.
Table Of Contents 1. REVISION HISTORY...................................................................................................................................................... 1 1.1. 2. 3. DOCUMENT REVISION HISTORY ................................................................................................................................... 1 GENERAL DESCRIPTION ..............................................................................................................................
1. Revision History Revision 1.00 Date 2011/1/4 Remark Product proposal 1.1. Document Revision History Revision 1.00 1.01 Date 2011/1/4 2011/9/27 Remark Preliminary product proposal Change Tx measured output power in peak value 1 Delta Networks Inc.
2. General Description HB97 is compliant with miniPCI Express v1.1 standard Adapter. The Atheros 802.11g/n technique delivers up to 54Mbps (802.11g) and IEEE802.11n data rate support the channel bandwidth support 20MHz for 150Mbps and 40MHz channel bandwidth for 300Mbps ( 2Tx2R) and support legacy WLAN standard IEEE802.11b, IEEE802.11g data rate, it use 2 sets of 2.4Ghz Tx / Rx antenna’s combinations and applied Transmit Beamforming and Receive combining to focus energy and CDD, MRC to improve 802.
2.2. Mechanical Design The Dimension : L x W (mm): 30mm x27mm 3 Delta Networks Inc.
2.3. IC Solution The IC solution for HB97: P/N AR9287 Functionality A powerful MAC/BBP for interface Description IEEE11g/n AR9287 is single chip solution for 2.4GHz 802.11n-ready ; it PCI-e card integrates a multiple protocol MAC, Baseband Processor and ADC/DAC converters with 2x2 MIMO radio transceiver including LNA, PA, and RF Switch and PCIe v1.
2.4. VID, DID, SVID and SPID assignment The SVID and SPID may provide from customer. 1. Vendor ID (VID): use Chip’s vendor ID = 0x168C 2. Device ID (DID): use Chip’s device ID = 0x4013 3. Sub-Vendor ID (SVID): use manufacture’s ID = 0x?? 4. Sub-Product ID (SPID): use manufacture’s product ID = 0x?? 5 Delta Networks Inc.
3. Technical Specifications HB97 Specification Specification Wireless LAN PC Card WLAN Standard IEEE802.11b, IEEE 802.11g; IEEE802.11e, IEEE802.11h; IEEE802.11i; IEEE802.11n standard Data Rate IEEE802.11b/g: 1/2/5.5/6/9/11/12/18/24/36/48 and 54Mbps And 802.11n data rate up to 300Mbps ( 40MHz); 130Mbps ( 20MHz) Wireless Medium Complementary code keying (CCK) and Orthogonal Frequency Division Multiplexing (OFDM); MIMO-OFDM Frequency Band 2.4GHzband:ISM band 2.412 –2.472, 2.
HB97 specification (continued) Specification Receive Sensitivity Wireless LAN PC Card 11b@CH6 -86dBm@11Mbps 11g@CH6: -74dBm@54Mbps; CH13: -74dBm@54Mbps 11n-20MHz BW: 2437MHz for MCS7: -70dBm 2437MHz for MCS15: -68dBm 11n-40MHz BW: 2422MHz for MCS7: -68dBm 2422MHz for MCS15: -65dBm Max output power 11b 19.9dBm@1Mbps 11g 24dBm@6Mbps 11n-20MHz BW : MCS0: 23.8dBm 11n-40MHz BW : MCS0: 22.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: (For mobile device use) Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs.
