DFWM-GIN00 User Manual DFWM-GIN00 An IEEE 802.11b/g/n Low-Power Wireless System-On-Chip module User Manual Sheet 1 of 17 July.
DFWM-GIN00 This document describes a simple method for characterizing DFWM-GIN00 WLAN module based RF parameters, such as transmitted spectra and receiver sensitivity. It will be described step by step below that how to control and setup. Step 1 : Extract to CDM20814_WHQL_Certified.zip, it is a USB to UART driver, then setup it. Step 2 : Setup teraterm_utf8-4.58.exe program, this program can help to send command to module.
DFWM-GIN00 Step 6 : Now any legal command can be keyed in and if UTF-8 reply ok, the command is implemented successful like below figure. Figure 3 802.
DFWM-GIN00 at+wrfteststart at+wtx100test=1,0,9,0,0,0,0,1,1,0,0,1,1,1 at+wtx100test=6,0,9,0,0,0,0,1,1,0,0,1,1,1 at+wtx100test=11,0,9,0,0,0,0,1,1,0,0,1,1,1 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 2Mbps Continuous Tx Channel 6, 2Mbps Continuous Tx Channel 11, 2Mbps Transmitter off Transmitted Tx at 1Mbps at+wrfteststart at+wtx100test=1,0,18,0,0,0,0,1,1,0,0,1,0,1 at+wtx100test=6,0,18,0,0,0,0,1,1,0,0,1,0,1 at+wtx100test=11,0,18,0,0,0,0,1,1,0,0,1,0,1 At+reset Start up internal Power
DFWM-GIN00 at+wtx100test=1,0,26,0,0,0,0,1,0,0,0,1,1,0 at+wtx100test=6,0,26,0,0,0,0,1,0,0,0,1,1,0 at+wtx100test=11,0,26,0,0,0,0,1,0,0,0,1,1,0 At+reset Continuous Tx Channel 1, 24Mbps Continuous Tx Channel 6, 24Mbps Continuous Tx Channel 11, 24Mbps Transmitter off Transmitted Tx at 18Mbps Command at+wrfteststart at+wtx100test=1,0,27,0,0,0,0,1,0,0,0,1,6,0 at+wtx100test=6,0,27,0,0,0,0,1,0,0,0,1,6,0 at+wtx100test=11,0,27,0,0,0,0,1,0,0,0,1,6,0 At+reset Action Start up internal Power Amplifier Continuous Tx Cha
DFWM-GIN00 at+wtx100test=1,0,18,0,0,0,0,1,0,0,0,1,7,2 at+wtx100test=6,0,18,0,0,0,0,1,0,0,0,1,7,2 at+wtx100test=11,0,18,0,0,0,0,1,0,0,0,1,7,2 At+reset Continuous Tx Channel 1, 72Mbps Continuous Tx Channel 6, 72Mbps Continuous Tx Channel 11, 72Mbps Transmitter off Transmitted Tx at MCS6 at+wrfteststart at+wtx100test=1,0,20,0,0,0,0,1,0,0,0,1,6,2 at+wtx100test=6,0,20,0,0,0,0,1,0,0,0,1,6,2 at+wtx100test=11,0,20,0,0,0,0,1,0,0,0,1,6,2 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 65Mbps Co
DFWM-GIN00 Transmitted Tx at MCS1 at+wrfteststart at+wtx100test=1,0,27,0,0,0,0,1,0,0,0,1,1,2 at+wtx100test=6,0,27,0,0,0,0,1,0,0,0,1,1,2 at+wtx100test=11,0,27,0,0,0,0,1,0,0,0,1,1,2 At+reset Start up internal Power Amplifier Continuous Tx Channel 1, 14.4Mbps Continuous Tx Channel 6, 14.4Mbps Continuous Tx Channel 11, 14.
DFWM-GIN00 Device Pin-out Diagram (Module top view) DFWM-GIB0x Device Pin-out Diagram (Module top view) User Manual Sheet 8 of 17 July.
DFWM-GIN00 Module Pins Description User Manual Sheet 9 of 17 July.
DFWM-GIN00 User Manual Sheet 10 of 17 July.
DFWM-GIN00 User Manual Sheet 11 of 17 July.
DFWM-GIN00 Antenna Information Frequency range Peak gain PCB Antenna 2400 MHz – 2500 MHz -3.06 dBi EIRP(2450MHz)-XY cut EIRP(2450MHz)-XZ cut User Manual Sheet 12 of 17 July.
DFWM-GIN00 EIRP(2450MHz)-YZ cut Antenna Location User Manual Sheet 13 of 17 July.
DFWM-GIN00 Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the frequency exposure limits.
DFWM-GIN00 Canada, avis d'Industry Canada (IC) Cet appareil et RSS-210. numérique de classe B est conforme aux normes canadiennes ICES-003 Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
DFWM-GIN00 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. Section 15.
DFWM-GIN00 -Consult the dealer or an experienced radio/TV technician for help. Part 15.19(a)(3) unlicensed project (WLAN Device) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device.
