DFWM-GIB03 User Manual DFWM-GIB03 An IEEE 802.
DFWM-GIB03 INTRODUCTION This document describes a simple method for characterizing DFWM-GIB03 WLAN module based RF parameters, such as transmitted spectra and receiver sensitivity. It will be described step by step below that how to control and setup. Step 1 : Extract to CDM20814_WHQL_Certified.zip, it is a USB to UART driver, then setup it. Step 2 : Setup teraterm_utf8-4.58.exe program, this program can help to send command to module.
DFWM-GIB03 Step 5 : After entering UTF-8, send command at. If connection is successful, it will reply ok. Step 6 : Now any legal command can be keyed in and if UTF-8 reply ok, the command is implemented successful like below figure.
DFWM-GIB03 at+rfwavetxstart=1,11,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,12,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,13,3,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,14,3,1,0,1,0,GainSpanDemo At+rfstop Continuous Tx Channel 11, 11Mbps Continuous Tx Channel 12, 11Mbps Continuous Tx Channel 13, 11Mbps Continuous Tx Channel 14, 11Mbps Stop action Transmitted Tx at 5.
DFWM-GIB03 at+rfwavetxstart=1,14,1,1,0,1,0,GainSpanDemo At+rfstop Continuous Tx Channel 14, 2Mbps Stop action Transmitted Tx at 1Mbps for every channel at+extpa=0 at+rfwavetxstart=1,1,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,2,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,3,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,4,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,5,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,6,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,7,0,1,0,1,0,GainSpanDemo at+rfwavetxstart=1,8,0,1,0,1,0,GainSpan
DFWM-GIB03 at+rfwavetxstart=1,13,3,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,14,3,1,0,1,2,GainSpanDemo At+rfstop Continuous Tx Channel 13, 11Mbps Continuous Tx Channel 14, 11Mbps Stop action Transmitted Tx at 5.
DFWM-GIB03 Transmitted Tx at 1Mbps for every channel at+extpa=1 at+rfwavetxstart=1,1,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,2,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,3,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,4,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,5,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,6,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,7,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,8,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,9,0,1,0,1,2,GainSpanDemo at+rfwavetxstart=1,10,0,1,0,1,2,GainSpanDemo at+rfwa
DFWM-GIB03 Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the Dell Wireless Device is below the Industry Canada (IC) radio frequency exposure limits.
DFWM-GIB03 Canada, avis d'Industry Canada (IC) Cet appareil et RSS-210. numérique de classe B est conforme aux normes canadiennes ICES-003 Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement.
DFWM-GIB03 Federal Communications Commission (FCC) Statement You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. Section 15.
DFWM-GIB03 connected. -Consult the dealer or an experienced radio/TV technician for help. Part 15.19(a)(3) unlicensed project (WLAN Device) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation of the device.