nations! You have just purchased a TCO'95 approved and belied product! Your ¢ has provided you with a product developed lor professional use. Your purchase contributed to reducing the burgeon on the environment and to the further development of environmentally-adapted electronic products Why do we have environmentally-labeled computers? In many countries, environmental labeling ¢ become an established method for encouraging battalion of goads and services to the environment.
FEDERAL COMMUNICATIONS COMMISSION NOISE This equipment has been tested and found to comply 3 rth the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
0m. U Econ] 14 DDC The monitor includes the DOC and SDC28 feature. COC (Display Data Channel} is a commune cation channel over which the monster automatically informs the host system about is capabilities (e.g. ~2ch supported resolution wile its corresponding timing). ted hiccough previously unused pins of the 18-pin VGA The system will perform "Plug and Play” feature if both, Bonita protocol. connector d host, implement the OCC 1.
0ai8. 08cm) 1.8 Quick Operation Chant adapter with Diamond Scan S0e color 7 2 the chant below To summarize the steps in connecting your computes an: monster and salting tha necessary controls and switches See 2.1 AC Power Connection 2.2 Signal Cable Connection See 3. USER CONTROLS 3 4, FUNCTION CONTROLS if a problem appears, sere si : . ~«fp— Scud, TROUBLESHOOTING If the problem persists. MITSUBISHI: 00344-6362 98.233, 13.
USER CONTROLS 34 Control Names See Figure & and 7 for the location of the fallowing user controls and indicators. d by number and is described individually or page 14. Each contra! is identity {How tc usa u Press the button the central pat i 1. POWER SWITCH & 2. POWER-CON INDICATOR 4. OSD OFF BUTTON €, FUNCTION ADJUST BUTTONS @3. INPUT CONNECTOR SELECT BUTTON 7. DEGASSED BUTTON 5, FUNCTION SELECT BUTTONS Figure 3.2 Function i POWER SWITCH: A push-on push-off switch tor AC power. 2.
SIGNAL INPUT CONNECTOR (D BE-15P) AC POWER CONNECTOR 8, SERIAL INTERFACE CONNECTOR SIGNAL INPUT CONNECTOR (BNC) (DIN-8) Figs 7 8 SERIAL INTERFACE CONNECTOR: The mentor has a DIN-8 connector for serial " interface communication. Bo 982.
0s) 4.1 Operation Press any select bitten and control indicators will be superimposed on the display screen called 1st layer. Refer to Figure 6 tor the location of the monitor function controls. Press the select buttons to choose one of the following controls. The indication of a function symbol changes to blue. When selected the function symbol of above OSD, press the adjust button the OSD screen changes to flowing raffled 2nd layer. Then you can adjust each friction by © buttons.
Symbol of 1st OSD lays 2nd O80 layer Press the Plus Adjust Button: © H-81ZE H-SIZE LEVEL: 00 100% To narrow the width of the image on the screen. To expand the width of the image on the screen. PHASE 80% LEVEL: 00 100% = To move the image 10 the left. Ne To move ihe image ta the sight. @ v-size @ -SIZE 90% LEVEL: 00 100% To narrow the height of the image on the screen. To expand the height of ihe image on the screen. @ v-POSITION [V-POSITION LEVEL: 00 100% Ee To move the image down.
Symbol of 1st OSD layer 2nd O80 layer Press the Minus Adjust Button: = Press the Plus Adjust Button: @ ROTATION Q (ROTATION LEVEL: 00 100% To notate 1o the let To rotate to the right, Press plus and minus buttons together, to restore to factory preset level. ® GEOMETRY RESET Te cancel the geometry reset operation, To reset the geometry data to factory adjusted condition.
ay4.2 POWER SAVE When the monitor has no syn signal or incorrect connection and the signal frequency is out of range, the following CAUTION comes on the screen. Check input signal, signal cabin connection and signal frequency. 1. POWER SAVE iS OFF When POWER SAVE is OFF and there is no sync signal, the following screen is displayed. ATTENTION NO 8 SIGNAL PLEASE CHECK INPUT SIGNAL OR CONNECT ION. 2.
73 SC-8102 Sinai Cable ' PIN ASSOC Approx. 1.8m = 5) DB-18P Ice © 5 coaxial ld UE GRINCH NC SYNC GROUND GROUND SOA . HORIZONTAL SYNC SIGNAL LEVEL NE. .
APPENDIX 71 Monitor Signal Input Connector (DB S-15F) PIN ASSIGNMENT Signal RED VIDEO GREEN DIVED C with GREEN VICED E VICED GROUND I DB 9-15P MOUNTED ON THE REAR PANEL DISPLAY DATA CHANNEL SERIAL DATA . SERIAL CLOCK NO-CONNECTION 7.2 (Female) MOUNTED ON THE REAR PANEL 28 | ares Ares ® hs COC GROUND RED FOUND of COMPOSITE SYNC VERTICAL GEOSYNCLINE} SCL Serial interface Input Connector (DIN-8) For Serial interface Function PIN ASSIGNMENT Pin No. _.
TROUBLESHOOTING Before calling your Authorized Product Support, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in SPECIFICATION 6 and APPENDIX 7 PROBLEM ITEMS TO CHECK LOCATION LED + Contrast and brightness controls. * Front (Adjust to the On-Green maximum brightness or push the reset button) LED * Power switch.
Symbol of 1st Press the Minus Adjust Button: | Press the Plus Adjust Button: < SOA pi OSD layer 2nd OSD layer Fo t+ iE USB PORT SELECT ? This "USB PORT SELECT" is prepared for optional USB STATUS pant "USE-unit KT-X406" installed only. PLEASE CHECK wa] MONITOR Attention OSD screen is displayed without USB unit CONNECTION OR USB IS SUSPENDED For installing USB-unit, please read the manual of USB kit, @ ADJUST LOCK 1.
@ Symbol of 1st OSD layer 2nd OSD layer Press he Minus Adjust Button: MY Press the Plus Adjust Bunion: Pa TF (© KEYSTONE O KEYSTONE LEVEL: 0G 100% The decrease the width at the top of the screen image and to increase the width at the bottom. The increase the width at the top of the screen image and to decrease the width al the bot torn. (@ PIN-BALANCE 0) PI N-BALANCE 80% I» p= LEVEL: 20 100% To move the top and bottom of the screen image to the right.
PP 2ee? Symbol of 1st OSD lays 2nd OSD layer Press the Minus Adjust Button: [FOF & @ CONTRAST > CONTRAST LEVEL: 00 100% To decrease the contrast. To increase the contrast. Press plus and minus buttons together, to restore to factory preset level. ©) BRIGHTNESS XE BRIGHTNESS 90% LEVEL: 00 100% To decrease the brightness. To increase the brightness Press plus and minus buttons together, to restore to factory preset level.
0SD(On Screen Display) FUNCTIONS {1} CONTRAST: Adjusts to the desired contrast level (2) BRIGHTNESS: Adjusts to the black level of the sateen (3) COLOR-TEMPERATURE: Adjusts the color temperature of the screen image. (4) INFORMATION: Individuate © "mri Frequency and “ou Idea signal pint {signal Co (5) H-SIZE (Horizontal Size): Controls the horizontal size of the image on the screen (6) H-PHASE (Horizontal Position): Contrails the horizontal petition of the image on the screen.
BNC CONNECTION {1} IN CAVE OF A COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC CN GREEN): Connect lhe R, G and B dives signals to the BNC receptacles oa the tack of the monster. 2) IN CASE CF EXTERNAL COMPOSITE SYNC Signal: Connect the B, G and B video signals and the Composite sync signal to 8MC receptacles an rear panel. respectively. CASE OF SEPARATE HORIZONTAL ANC VERTICAL SYNC SIGNALS: Connect the RB.
9068.06 703) CONNECTING THE MONITOR On the back of the monitor are four plug-in connections: one for the AC power cord, DB S-15P connector, BNC connector for video and a DIN-8 connector for the optional USB-unit 2.1 AC Fowler Connect . One end of the AC power cord is connected into the AC power connector on the back of the monitor. The loner end is plugged into a properly grounded three-prong AC outlet.
1.7 Unpacking Alter you unpack the box and packing materials in cards. u wud nave zl of the items indicated in Figure 1. Save the box hip Of isa the monitor plate and mal in warranty 1. Diamond Scan 30e Color Monitor 2. AC Prows Cord 3. Sinai Cable SC-B102 User's Guide 6. Warranty-Set 1.8 Swivel Base @ The monitor comes with a swivel base.
Diamond Scan 90e User's Guide _ CONTENTS . INTRODUCTION 1.1 Features... 1 3 internal Preset Memory C 1.3 Power Management 7 Function 1.4006 1.5 Location n Cons rations 1.8 Cleaning Your Monitor Unpacking... 1.8 Swivel Base Screen Position Adjustment 1.9 Quick Operation Chart CONNECTING THE MONITOR 2.3 AC Power Connection .. 2 Sinai Cable Connection .. Scanning to Any 1BM VGA Com pal bie System en ra 3. USER CONTROLS . 3.1 Corral Names. 3.2 Function 4 GSD(On Screen Display} FUNCTIONS 4,1 Operation... 4.
mn a sn tinting SME 2 [ the middle of trees page, you will find a brief summary of the environmental: 1 crier document may be in and af requirements met by this product. The complete environment ordered from: TCC Development Unit S-114 94 Stockholm Sweden Fan +46 8 78292 07 « E-mail {Internet}.