VENTILATION FAN MODEL Pro200/Pro300 TABLE OF CONTENTS Package Contents 2 General Safety Information 3 Preparation and Wiring Diagrams 4 Assembly Instructions 5 Grille Installation 6 Operation 6 Care and Maintenance 7 Troubleshooting 8 Dimensions 9 9 Warranty READ AND SAVE THESE INSTRUCTIONS Address: 46101 Fremont Boulevard, Fremont, CA 94538 US Toll Free Number: 1-888-979-9889 www.deltabreez.
PACKAGE CONTENTS No.
GENERAL SAFETY INFORMATION be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit Interrupter) – protected branch circuit. READ AND SAVE THESE INSTRUCTIONS GENERAL SAFETY INFORMATION 1. Make sure that the electric service supply voltage is AC 120V, 60Hz. 8. Do not use this unit with any other solid-state control device. Solid-state controls may cause harmonic distortion, which can cause a motor humming noise.
PERPARATION AND WIRING DIAGRAMS Proper insulation around the fan to minimize building heat loss and gain. The ducting from this fan to the outside of the building has a strong effect on the air Roof cap (with built-in damper) Short piece of flexible duct helps alignment and absorbs sound straightest duct routing possible for best performance, and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit mold growth.
ASSEMBLY INSTRUCTIONS BEFORE INSTALLATION Turn off power source. Review all safety precautions. 1 Machine screw (M4 x 6) ATTACH DUCT CONNECTOR 1.Attach the duct connector from outside, and secure it to fan body by using machine screw (M4x6) . Hardware Machine Screw (M4x6) 2 MOUNT HOUSING WITH SUSPENSION BRACKETS Tapping screw 2. Assemble suspension bracket and rubbers to fan body, secure them to fan body by using tapping screws ( Ø4 x 10) Suspension bracket Rubber 3 3.
GRILLE INSTALLATION 1 Insert the mounting springs into the slots and mount the grille to the fan body. Slots Slots Slots Spring OPERATION Spring Turn the power switch on , the LED indicator will be green.
TALLATION CARE AND MAINTENANCE TURN OFF POWER SOURCE. REVIEW ALL SAFETY PRECAUTION See safety information before proceeding. Routine maintenance should be done at least once a year. • Never use solvents, thinner or harsh chemicals when cleaning the fan. • Do not allow water to enter the motor. • Do not immerse metal parts in water. • Do not immerse resin parts in water over 140º F. 1 1. To remove grille, squeeze springs and pull down. 2 2. Clean the grille with a cloth. 3 3.
TROUBLESHOOTING PROBLEM The fan is not turning on The fan seems louder than it should POSSIBLE CAUSE CORRECTIVE ACTION 1. Power off 1. Make sure power supply is on. 2. Faulty switch 2. Test or replace switch. 3. Faulty wire connection 3. Check wire in switch box. 1. CFM too great 1. Be sure the CFM rating on the fan matches the size of your room. 2. Damper not working properly or damaged 2. Check damper to ensure it is opening and closing properly.
DIMENSIONS 6" 7 5/8 " 15 12 1/4 /4 1 12 " " 15 " " PRODUCT SPECIFICATIONS SPECIFICATIONS Voltage (V) Frequency (Hz) Power @ 0.1”SP (W) Air Flow @ 0.1”SP (CFM) Weight (lb.) Max.Current (amps) Pro200 120 60 17.5 200 12.6 0.52 Pro300 120 60 41.0 300 12.6 0.72 Model No.
WARRANTY DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA and Canada that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions 1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation by the consumer.