Delphi Audio System Installation & Operation Guide
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Warning: To prevent fire or shock hazard, do not expose the Delphi Audio System to rain, moisture, or water.
Table of Contents What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting up the Delphi Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using SKYFi/SKYFi2 with the Delphi Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Using roadyXT with the Delphi Audio System . . . . . . . . . . . . . . . . . . .
What’s in the Box Your Delphi Audio System Kit contains the following components: 12V DC adaptor Battery compartment and antenna cable storage 12V DC jack XM Antenna Setting up the Delphi Audio System Set up your Delphi Audio System by following these steps: 1. Connect the supplied 12V DC power adaptor to the jack on the rear of the Delphi Audio System, and the other end to a wall outlet. 2.
Using SKYFi/SKYFi2 with the Delphi Audio System 1. Insert the SKYFi/SKYFi2 Receiver (sold separately) into the cradle by first pressing in on the back of the black inset cradle in the Delphi Audio System. Then letting the cradle tilt forward, carefully slide the SKYFi/SKYFi2 Receiver down into the tray so that the alignment tabs on the sides of the tray line up with the slots on SKYFi/SKYFi2 and the connector is completely seated.
Using the Delphi Audio System with Batteries The Delphi Audio System can be used with batteries (not supplied) to allow you to listen to XM outdoors or in other locations without access to an AC power source. Alkaline or rechargeable NiCD batteries are recommended. Battery life will vary depending on how the system is operated and the type of batteries being used. It is recommended that the AC adaptor be the primary power source for the Delphi Audio System in order to preserve battery life. 1.
Installing the XM Antenna on the Rear of the Delphi Audio System When outdoors with a view of the southern sky, or in an area of repeater coverage, or when receiving a strong signal indoors, you can conveniently mount the antenna directly on the back of the Delphi Audio System. 1. Remove the battery compartment and antenna cable storage cover as described in “Setting up the Delphi Audio System,” wind the antenna around the two cable hooks, leaving several inches of cable free, and replace the cover. 2.
2. Attach four screws to the wall using the screw-locator pattern shown here. Photocopy the pattern to use as a template. Use screws with head sizes small enough to fit in the center of each of the four holes but large enough not to pop out of the elongated sections. Leave 1/8" of the screw shanks behind the heads sticking out of the wall. Photocopy this diagram of the screw-locator pattern on the bottom of your XM Antenna to use as a template for wall attachment. 3.
Note that the “Line Out Level” cannot be reset while the receiver is in the Delphi Audio System since the volume control should be used to control the audio output instead. If the line out setting is adjusted while in a car cradle or home stand and the receiver is later reconnected to the Delphi Audio System, it will automatically return to the prior setting the next time it is used in a vehicle adaptor or home adaptor.
2. On placement: • Do not place the Delphi Audio System on an inclined or unstable surface. • Do not place anything within 1/2" of the side of the cabinet. The audio/ventilation ports must be unobstructed for the Delphi Audio System to operate properly and prolong the life of its components. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the unit to prevent possible damage from the magnetic fields. 3.
Specifications ITEM UNIT SPECIFICATION NOMINAL LIMITED REMARK Rated output (10%) at 1 KHz 1 Continuous average power output W >4 >3.5 2 Total harmonic distortion % >0.6 >1.0 3 Sensitivity mV 180 140~235 4 Frequency response Hz 65~22K 70~20K 5 Signal to noise ratio dB >65 >60 6 Channel separation dB >45 >40 Input: Short Level 1 0 dB: 2.0 V/1 KHz 7 Input impedance Ohm – – Normal input Frequency 1 KHz – – Floating input >4.7K >4.
www.delphi.com and for all products for the remainder of the limited warranty period, you must contact Delphi by phone at 1.877.GO DELPHI (1.877.463.3574). If further clarification or additional information is required from Delphi, you may call Delphi at 1.877.GO DELPHI (1.877.463.3574). If warranty service is needed at any time during the warranty period, the purchaser will be required to furnish a sales receipt/proof of purchase indicating the date of purchase, amount paid, and place of purchase.