Support Matrix

ManualsBrandsDell ManualsAX NodesXC730 Hyper-converged Appliance

Dell EMC Support Matrix

Dell EMC XC730 Series Hyper-Converged

Appliance Support Matrix

December 2020

Summary of content (21 pages)

PAGE 1
Dell EMC XC730 Series Hyper-Converged Appliance Support Matrix December 2020 Dell EMC Support Matrix
PAGE 2
Revisions Revisions Date Description December 2020 Updated the Supported management software section. September 2020 Updated the following sections: • • • Supported NICs and NDCs Supported management software Supported hypervisor OSs February 2020 Updated the Supported Hypervisor OS section. June 2019 Updated the following sections: • • Supported Management Software Supported Hypervisor OS August 2018 Updated Firmware and BIOS and removed DPMC information.
PAGE 3
Table of contents Table of contents Revisions............................................................................................................................................................................. 2 Table of contents ................................................................................................................................................................ 3 Introduction ................................................................................................
PAGE 4
Introduction Introduction This document provides information about the supported software, firmware, and hardware versions and technical specifications for the Dell EMC XC730-16G Series Hyper-Converged Appliance. This Support Matrix contains the latest compatibility and interoperability information. If you observe inconsistencies between this information and other documentation or references, this document supersedes all other documentation.
PAGE 5
Supported hardware, firmware, and software 1 Supported hardware, firmware, and software This chapter provides information about supported software, firmware, and hardware versions for the Dell EMC XC730 Series Hyper-Converged Appliance. NOTE: Future updates to this document may remove firmware versions because Nutanix LCM is the prescribed method to update the appliance. 1.
PAGE 6
Supported hardware, firmware, and software Component v3 Version v4 Version 1.3.6 or later 2.7.1 or later 2.02.02.02 or later 2.52.52.52 or later BIOS iDRAC support 1.2 Validated BIOS and iDRAC versions Each row in the table below represents the validated BIOS and iDRAC version pair. Validated BIOS and iDRAC versions 6 BIOS iDRAC 1.3.6 2.02.02.02 1.3.6 2.20.20.20 1.5.4 2.20.20.20 2.0.2 2.30.30.30 2.0.2 2.40.40.03 2.1.6 2.40.40.03 2.2.4 2.40.40.40 2.3.4 2.40.40.40 2.4.3 2.43.43.
PAGE 7
Supported hardware, firmware, and software 1.3 Supported physical disk drives This section provides information about disks drives supported by your hardware. Supported physical disk drives 7 Form Factor Capacity Type Vendor 2.5" 1 TB NL-SAS HDD Dell EMC Supported 2.5" 2 TB NL-SAS HDD Dell EMC Supported 2.5" 1.2 TB SAS HDD Dell EMC Supported 2.5" 1 TB SED SAS HDD Dell EMC Supported 2.5" 1.2 TB SED SAS HDD Dell EMC Supported 2.5" 2.0 TB SED SAS HDD Dell EMC Supported 2.
PAGE 8
Supported hardware, firmware, and software 1.4 Supported HBAs This section provides information about Host Bus Adapters (HBA) supported by your hardware. Supported HBAs Name Form factor/Slot H730 Mini or integrated slot Minimum firmware Latest version version 25.3.0-0016 Windows driver for H730 HBA330 25.5.5.0005 6.604.06.00 Mini or integrated slot 9.17.20.07 15.17.09.06 NOTE: This version is supported on AOS 4.1.3. x. Window Server 2012R2, 2016 drivers for HBA330 1.5 v2.51.21.
PAGE 9
Supported hardware, firmware, and software 1.6 1.7 Supported NICs and NDCs Supported NICs Vendor Description Chipset Intel CRD,NTWK,10G BASET,DP,INTEL,LP x540 CRD,NTWK,12G,RNDC,INTEL,10GSFP x540/i350 CRD,NTWK,12G,RNDC,INTEL,2+2,V3 x540/i350 CRD,NTWK,10G,SFP+,DP,INT,LP,V2 x520 Supported hardware management solutions This section provides information about hardware management solutions that are supported by your appliance.
PAGE 10
Supported hardware, firmware, and software 1.8 Supported management software This section provides information about components supported by your appliance. Supported management software 1.9 Name AOS version (Skylake) AOS version (Cascade lake) AHV 5.1 or later 5.10.3.2 or later Windows Server 2016 5.5.0.4 or later 5.10.3.2 or later Windows Server 2019 5.17 or later 5.17 or later ESXi 6.0U3 (EOL date 3/12/2020) 5.1 or later 5.10.3.2 or later ESXi 6.5d 5.1 or later 5.10.3.
PAGE 11
Technical specifications 2 Technical specifications 2.1 Physical specifications This chapter provides technical specifications for Dell EMC XC730 Hyper-Converged Appliance. This section provides expansion physical specifications for storage, including height, width, depth, maximum configuration weight and empty weight. Physical specifications 2.2 Physical Specification Height 8.73 cm (3.44 inch) Width 48.2 cm (18.98 inch) Depth 75.58 cm (29.75 inch) Weight (Maximum) 31.4 kg (69.23 lb.) (2.
PAGE 12
Technical specifications Expansion Bus Specification (Slot 3) One low profile, low profile x8 link Riser 2 (Slot 4) One full-height, full-length x16 link NOTE: To use slots 1 through 4, both the processors must be installed. (Slot 5) One full-height, full-length x8 link Riser 3 2.4 (Slot 6) One full-height, full-length x16 link Power specifications This section provides power specifications for your hardware, including wattage, heat dissipation, and voltage.
PAGE 13
Technical specifications Memory Specification Maximum RAM Up to 1.5 TB with a dual processor Minimum RAM 64 GB with a dual processor 2.6 Hard drive specification This section provides hard drive specifications for your hardware. Hard drive specification 2.7 Type Specification Ten hard-drive systems Up to sixteen 2.5 inches, internal, hot-swappable drives in hard-drive slots 0−15.
PAGE 14
Technical specifications 2.8 Video specifications This section provides video specifications for storage, including type, and memory. Video specifications 2.9 Type Specification Video type Matrox G200eR2 Video memory 16 MB Environmental specifications This section provides environmental specifications for storage, including temperature, relative humidity, maximum vibrations, particulate contamination, gaseous contamination, and expanded operating temperature.
PAGE 15
Technical specifications Type Specification Operating Six consecutively run shock pulses in the positive and negative x, y, and z axes of 40 G for up to 2.3 ms. Maximum altitude Operating 3,048 m (10,000 ft) Storage 12,000 m (39,370 ft) Operating altitude de-rating Up to 35°C (95°F) Maximum temperature is reduced by 1°C/300 m (1°F/547 ft) above 950 m (3,117 ft). 35°C to 40°C (95°F to 104°F) Maximum temperature is reduced by 1°C/175 m (1°F/319 ft) above 950 m (3,117 ft).
PAGE 16
Technical specifications Type Specification NOTE: Applies to data center and non-data center environments. Gaseous contamination Note: Maximum corrosive contaminant levels measured at ≤50% relative humidity. Copper coupon corrosion rate <300 Å/month per Class G1 as defined by ANSI/ISA71.04-1985. Silver coupon corrosion rate <200 Å/month as defined by AHSRAE TC9.9.
PAGE 17
Documentation Matrix 3 Documentation Matrix The documentation matrix provides information about the documents that you use to configure and deploy the Dell EMC Hyper-Converged Appliance solution. WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included with this document or as a separate document.
PAGE 18
Documentation Matrix 3.2 To learn about... Refer to... How to deploy and set up this solution Solutions Guide Setting up and using Dell EMC iDRAC8 Dell EMC iDRAC8 Quick Start Guide Using OpenManage Essentials to monitor, perform updates, view hardware, and view inventory on your system Dell EMC OpenManage Essentials User's Guide Nutanix documentation Nutanix documentation is found using the Nutanix portal found at https://portal.nutanix.com/#/page/docs.
PAGE 19
Documentation Matrix 19 To learn about... Acropolis base document name Software instructions for hardware components that are not functioning. AHV Administration Guide Software instructions for hardware components that are not functioning. Hardware Replacement Documentation Comprehensive instructions and references for the Nutanix UI, including overview information. Prism Web Console Guide Monitoring multiple Nutanix cluster through web console.
PAGE 20
Contacting Dell EMC 4 Contacting Dell EMC Dell EMC provides several online and telephone-based support and service options. If you do not have an active internet connection, you can find contact information about your purchase invoice, packing slip, bill, or Dell EMC product catalog. Availability varies by country and product, and some services may not be available in your area. To contact Dell EMC for sales, technical assistance, or customer-service issues: 1. Go to Dell.com/support. 2.
PAGE 21
Quick Resource Locator 5 21 Quick Resource Locator Use the Quick Resource Locator (QRL) to get immediate access to Dell EMC XC730 solution information. This information provides access to reference documentation, a link to the Dell EMC support page, and links to hardware-specific QRL pages, which include how-to videos. You can access this information by visiting www.dell.com/QRL or by using your smartphone or tablet and scanning the QR code below.