Monitor mount for 2016 E-series and E2417H Dell monitors Installation guide
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, Dell EMC and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 Supported clients and monitors...................................................................................................................... 4 2 Included in the tool kit................................................................................................................................... 5 3 Mounting the client.......................................................................................................................................
1 Supported clients and monitors The monitor mount for 2016 E-series and E2417H monitors is designed to work with the following clients and monitors: NOTE: The mount is designed to work with Dell monitors and clients listed in this section. The mount should not be used with other Dell or third party monitors or clients.
2 Included in the tool kit Parts provided in the tool kit include: 1 Four shoulder screws (M4x0.7-6) 2 Four screws 3 Four hexagonal nuts (M4x0.7) 4 One monitor mount for E-series/E2417H monitors 5 One monitor base extender NOTE: Dell Wyse 3010 client requires horizontal stand 452–BCMF with the E-series mount. Dell Wyse 3020 and 5030 clients require horizontal stand 452–BCMH with E-series mount. Dell Wyse 3030 and 3030LT clients require horizontal stand 452–BCMG with E-series mount.
3 Mounting the client Use the following instructions to attach the client to the E-series mount: 1 Preparing the client—Use a Phillips-head screwdriver to remove the filler screws from the side of the client and replace them with 2 Removing the cover plates and screws from the monitor. the shoulder screws. • Place the monitor panel face down on a soft cloth or cushion. • Remove cover plate if present.
3 Attaching the base extender—Slide the base extender onto the monitor stand and use the screws provided in the tool kit to secure the base extender to the monitor stand.
CAUTION: Do not overtighten the screws. 4 Attaching E-series mount to the monitor— Position the E mount on the back of the monitor and attach it by using the monitor screws at 4 locations. CAUTION: Do not overtighten the screws. 5 Attaching the client—Slightly tip the client to align and insert the four protruding shoulder screws into the cutout areas of the Eseries mount. Slide the client until it snaps into place. The security latch moves automatically when the shoulder screws are inserted.
6 Connecting cables—To complete your setup, make all the desired connections, and then plug the AC power cord into an AC wall outlet. NOTE: To remove the client, gently pull the security latch to the right to release shoulder screws and slide the client from mount.
4 Mounting Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients Use the following instructions for mounting the Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients to the E-series monitor mount. These thin clients require mounting of the thin client to their respective horizontal stands before installing the thin client to the E-series monitor mount. The following horizontal stands are required by the respective thin client models: Table 1.
2 Attaching the base extender–Slide the base extender onto the monitor stand and use the screws provided in the tool kit to secure the base extender to the monitor stand. 3 Attaching the E mount to the monitor–Remove the four screws from the back of the monitor. Position the E mount on the back of the monitor, and attach it using the same screws.
Mounting Wyse 3010, Wyse 3020, Wyse 3030, Wyse 3030LT, and Wyse 5030 clients
4 Attaching the client–Align the client, and insert the shoulder screws into the four cut-out areas of the mount. The security latch moves automatically when the shoulder screws are inserted. The security latch is highlighted with the number 1 in the following image. 1. Security latch. 5 Connecting cables–To complete your setup, make all the desired connections, and then plug the AC power cord into an AC wall outlet.