Dell Networking W-7010 Controller Installation Guide
Copyright © 2015 Aruba Networks, Inc. Aruba Networks trademarks include , Aruba Networks®, Aruba Wireless Networks®, the registered Aruba the Mobile Edge Company logo, and Aruba Mobility Management System®. Dell™, the DELL™ logo, and PowerConnect™ are trademarks of Dell Inc. All rights reserved. Specifications in this manual are subject to change without notice. Originated in the USA. All other trademarks are the property of their respective owners.
Contents Preface.......................................................................................................................................................................5 Guide Overview................................................................................................................................... 5 Related Documentation..................................................................................................................... 5 Contacting Dell......................
Physical...................................................................................................................................... 25 Power Supply Specifications ................................................................................................. 25 Operating Specifications ........................................................................................................ 25 Storage Specifications .................................................................................
Preface This document describes the hardware features of the Dell Networking W-7010 Controller. It provides a detailed overview of the physical and performance characteristics of the controller, and explains how to install the controller and its accessories. Guide Overview Chapter 1, “W-7010 Controller” on page 7 provides a detailed hardware overview of the W-7010 controller and each of its components.
This page is intentionally left blank.
Chapter 1 W-7010 Controller The Dell Networking W-7010 Controller is a wireless LAN controller that connects, controls, and intelligently integrates wireless Access Points (APs) and Air Monitors (AMs) into a wired LAN system. There are two models of the W-7010 controller that do not differ physically or functionally from each other.
Table 4 Package Contents (Continued) Item Quantity Dell Safety, Environmental, and Regulatory Information (printed) 1 Dell Warranty and Support Information (printed) 1 NOTE: Optional accessories are available for use with the W-7010 controller, and are sold separately. Contact your Dell sales representative for details and assistance. W-7010 Components This section introduces the different components and its location in the W-7010 controller.
Table 5 W-7010 Controller Components (Continued) Callout Component Description 6 Enter Button Allows execution of actions on the LCD Screen 7 USB Interface 2 x USB 2.
Table 6 10/100/1000BASE-T Ethernet Port LEDs (Continued) LED Function LCD Mode Indicator Status STATUS Port status Administrative Green (Solid) Port enabled Off Port Administratively disabled Green (Solid) Full-duplex Off Half-duplex Green (Solid) PoE enabled Green (Blinking) Power enabled, but power denied due to unavailability Off PoE not enabled Green (Solid) 1000 Mbps Off 10/100 Mbps Duplex PoE Speed Uplink Ports The W-7010 controller includes two 1000BASE-X uplink ports (16
Each uplink port has two LEDs that allow basic monitoring of link/port status and activity.
LCD Mode Menu The LCD mode menu includes four modes as shown in the following table. Table 9 LCD Panel Mode LCD Mode Function Displayed Status/Command Description Boot Displays the controller boot up status. “Booting ArubaOS... Boot status of the controller. LED Displays the mode of the STATUS LED. The LED mode menu allows to choose what information is communicated by the STATUS LEDs on each port. See Table 6 on page 9 for descriptions of the LED behavior of each mode.
To disable only the Maintenance menu or one of its sub-menus, enter the Enable mode and use the following CLI commands: (host) #configure terminal (host) (config) #lcd (host) (lcd-menu) #disable menu maintenance ? factory-default halt-system media-eject reload-system upgrade-image upload-config (host) (lcd-menu) #disable menu maintenance upgrade-image ? partition0 partition1 USB Interface The W-7010 controller is equipped with a USB 2.0 interface. See Figure 4 on page 10.
Console Port Use the serial Console port to allow direct local management. See Figure 4 on page 10. This port is an RJ-45 female connector that accepts an RS-232 serial cable with a male connector.
In dynamic mode, the per port power budgeted from the total power supplied from the PSUs is equal the amount of power consumed by the port. Grounding Point To meet safety and electromagnetic interference (EMI) requirements and to ensure proper operation, the controller must be adequately grounded before power is connected. Connect a grounding cable to earth ground and then attach it to the chassis grounding point using two screws.
This page is intentionally left blank.
Chapter 2 Installation CAUTION: Installation of the device should be performed by a trained installation professional. This chapter describes how to install a W-7010 controller using the different mounting options available. The W7010 controller ships with an accessory kit that includes the equipment needed to install the controller in standard, 19-inch telco rack or on a wall.
Do not ship or store this product near strong electromagnetic, electrostatic, magnetic, or radioactive fields. Do not disassemble the chassis. Selecting a Location The W-7010 controller, like other network and computing devices, requires the following “electronic-friendly” environment: Reliable power Verify that the electrical outlet is compatible with the W-7010 controller power supply.
Installation Steps To install a W-7010 controller in a two-post 19-inch Telco rack: 1. Place the mounting brackets over the mounting holes on the controller (see Figure 7). 2. Secure the brackets to the controller using the eight screws for the mounting bracket (four per bracket) and a suitable screwdriver. Figure 7 Attaching the Mounting Brackets for Rack Mounting 3. In the desired rack system, if the rack requires cage nut or clip nut, insert it on the front rails (two per rail, aligned horizontally).
Table or Shelf Installation Required Tools and Equipment Rubber Feet Installation Steps 1. Attach the rubber feet to the bottom of the controller (see Figure 9). Figure 9 Attaching Rubber Feet 2. Place the controller on the desired flat table or shelf. Wall Mounting The mounting brackets can also be used for wall mounting the W-7010 controller.
Figure 10 Attaching the Mounting Brackets for Wall Mounting 2. After choosing a mounting location, mark the locations on the wall for the mounting holes. 3. Create the holes and insert wall anchors if the installation requires them. 4. Align the mounting bracket holes with the holes created in the wall (see Figure 11). 5. Use appropriate screws to secure the W-7010 controller.
Connecting and Disconnecting the AC Power Cord Once the controller is installed, it is ready to be powered on. The W-7010 controller is not equipped with an On/ Off switch. The device will power on when the AC power cord is connected to the power supply and an AC power outlet. Connecting the AC Power Cord To connect the AC power cord to the W-7010 controller: 1. Lift the power cord retaining clip so that it is not blocking the AC power connector. 2.
Removing an SFP To remove an SFP module: 1. Open and release the latch on the SFP module. 2. Pull and remove the module from the port. Connecting an LC Fiber Optic Cable To connect an LC fiber optic cable into an SFP-SX or SFP-LX module: 1. Clean the fiber optic cable connector before inserting it into the SFP module. 2. Insert the fiber optic cable into the SFP module. Ensure that the latch on the cable faces the top of the SFP module (see Figure 13). 3.
This page is intentionally left blank.
Chapter 3 Specifications, Safety, and Compliance W-7010 Specifications Physical Device Dimensions (without mounting brackets) (HxWxD): 1.74” x 12.75” x 13.0” (4.42 cm x 31.75 cm x 33.0 cm) Device Weight: 7.4 lbs (3.4 kg) Power Supply Specifications 225W AC Power Supply AC Input Voltage: 100 VAC to 240 VAC AC Input Current: 3.5 A max.
For continued compliance with the above laser safety standards, only approved Class 1 modules from our approved vendors should be installed in the product. CAUTION: Although this controller has been tested up to 1kV per CE immunity requirements, this product requires surge protection to be provided as part of the building installation to protect against unidirectional surges resulting from electrical switching and lightning strikes.
Taiwan (BSMI) Europe WARNING: This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. This product complies with EN55022 Class A and EN55024 standards. South Korea Class A: Battery Statements CAUTION: Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie due même type ou d’un équivalent recommandé par le constructeur.
European Union RoHS Dell products also comply with the EU Restriction of Hazardous Substances Directive 2011/ 65/EU (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine.