Dell™ Vostro™ 200 Owner’s Manual – Slim Tower Model DCSLF w w w. d e l l . c o m | s u p p o r t . d e l l .
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. If you purchased a Dell™ n Series computer, any references in this document to Microsoft® Windows® operating systems are not applicable.
Contents 1 Finding Information 2 Setting Up and Using Your Computer . . . . . . . . . . . . . . . . . 11 . . . 15 Front View of the Computer . . . . . . . . . . . . . . . 15 Back View of the Computer . . . . . . . . . . . . . . . 17 . . . . . . . . . . . . . . 18 Back Panel Connectors Installing Your Computer in an Enclosure . . . . . . . 20 . . . . . . . . . . . . . . . . . . . 22 . . . . . . . . . . . . . . . . . . . . 23 Setting Up a Printer Printer Cable . . . . . . . . . . . .
Power Management Options in Windows XP Standby Mode . . . . . 33 . . . . . . . . . . . . . . . . . . . 33 . . . . . . . . . . . . . . . . . . 34 Hibernate Mode Power Options Properties . . . . . . . . . . . . . Power Management Options in Windows Vista Standby Mode . . . . 36 . . . . . . . . . . . . . . . . . . . 37 . . . . . . . . . . . . . . . . . . 38 Hibernate Mode Power Plan Properties . . . . . . . . . . . . . . . Enabling SpeedStep™ Technology About RAID Configurations 40 . . .
Drive Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 . . . . . . . . . . . . . . . . 60 Optical drive problems Hard drive problems E-Mail, Modem, and Internet Problems Error Messages 58 . . . . . . . . 60 . . . . . . . . . . . . . . . . . . . . . 63 Keyboard Problems . . . . . . . . . . . . . . . . . . . Lockups and Software Problems . . . . . . . . . . . . 64 65 The computer does not start up . . . . . . . . . .
Video and Monitor Problems If the screen is blank . . . . . . . . . . . . . . 77 . . . . . . . . . . . . . . . . 77 . . . . . . . . . . 78 . . . . . . . . . . . . . . . 79 . . . . . . . . . . . . . . . . . . . . . . 79 . . . . . . . . . . . . . . . . . . . . . . . 80 If the screen is difficult to read . 4 Troubleshooting Tools Power Lights . Beep Codes System Messages Dell Diagnostics . . . . . . . . . . . . . . . . . . . . 82 . . . . . . . . . . . . . . . . . . . . .
5 Removing and Installing Parts Before You Begin . . . . . . . . 99 . . . . . . . . . . . . . . . . . . . . 99 Recommended Tools . . . . . . . . . . . . . . . . Turning Off Your Computer . . . . . . . . . . . . . 99 100 . . . . . . 100 Removing the Computer Cover . . . . . . . . . . . . . 101 Removing the Support Bracket . . . . . . . . . . . . . 102 Inside View of Your Computer . . . . . . . . . . . . . 104 . . . . . . . . . . . . . . . 105 Before Working Inside Your Computer .
Floppy Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 . . . . . . . . . . . . . . . . . . . . 139 . . . . . . . . . . . . . . . . . . . . . . . . . . 143 Media Card Reader . Optical Drive Battery Replacing the Battery Power Supply . . . . . . . . . . . . . . . 143 . . . . . . . . . . . . . . . . . . . . . . 145 . . . . . . . . . . . . 145 . . . . . . . . . . . . . . . . . . . . . . . . . 147 Replacing the Power Supply I/O Panel . . . . . . . . . . . . . .
6 Appendix . . . . . . . . . . . . . . . . . . . . . . . . 165 Specifications . . . . . . . . . . . . . . . . . . . . . . 165 System Setup . . . . . . . . . . . . . . . . . . . . . . 170 . . . . . . . . . . . . . . . . . . . . . . 170 Overview Entering System Setup . . . . . . . . . . . . . . . 170 System Setup Options . . . . . . . . . . . . . . . 172 . . . . . . . . . . . . . . . . . . 174 Boot Sequence . Clearing Forgotten Passwords . . . . . . . . . . . . . 176 . . . . . . . . .
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Index 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Finding Information NOTE: Some features or media may be optional and may not ship with your computer. Some features or media may not be available in certain countries. NOTE: Additional information may ship with your computer. What Are You Looking For? Find it Here • • • • • • Dell™ Product Information Guide Warranty information Terms and Conditions (U.S.
What Are You Looking For? Find it Here • Service Tag and Express Service Code • Microsoft Windows License Label Service Tag and Microsoft® Windows® License These labels are located on your computer. • Use the Service Tag to identify your computer when you use support.dell.com or contact support. • Enter the Express Service Code to direct your call when contacting support.
What Are You Looking For? Find it Here • Solutions — Troubleshooting hints and tips, articles from technicians, and online courses, frequently asked questions • Community — Online discussion with other Dell customers • Upgrades — Upgrade information for components, such as memory, the hard drive, and the operating system • Customer Care — Contact information, service call and order status, warranty, and repair information • Service and support — Service call status and support history, service contract, o
What Are You Looking For? Find it Here • How to use Windows Vista™ • How to work with programs and files • How to personalize my desktop Windows Help and Support Center 1 To access Windows Help and Support: • In Windows XP, click Start and click Help and Support. • In Windows Vista™, click the Windows Vista Start button and click Help and Support. 2 Type a word or phrase that describes your problem, and then click the arrow icon. 3 Click the topic that describes your problem.
Setting Up and Using Your Computer Front View of the Computer 1 2 3 4 5 6 7 8 9 10 11 Setting Up and Using Your Computer 15
1 location of Service Tag Use the Service Tag to identify your computer when you access the Dell Support website or call technical support. 2 eject button for optical drive Press here to open or close the optical drive. 3 FlexBay open/close Press here to open or close the floppy/media card reader panel 4 optical drive Can contain an optional optical drive. 5 FlexBay drive Can contain an optional floppy drive or optional Media Card Reader.
Back View of the Computer 5 1 2 3 4 1 back panel connectors Plug USB, audio, and other devices into the appropriate connector. See "Back Panel Connectors" on page 18 for more information. 2 card slots Access connectors for any installed PCI and PCI Express cards. 3 power supply LED Indicates power availability for power supply.
4 power connector Insert the power cable. 5 padlock rings Padlock rings are for attaching a commercially available theft-deterrent device. The padlock rings allows you to secure the computer cover to the chassis with a padlock to prevent unauthorized access to the inside of the computer. To use the padlock rings, insert a commercially available padlock through the rings, and then lock the padlock.
2 network adapter connector To attach your computer to a network or broadband device, connect one end of a network cable to either a network port or your network or broadband device. Connect the other end of the network cable to the network adapter connector on the back panel of your computer. A click indicates that the network cable has been securely attached. NOTE: Do not plug a telephone cable into the network connector. On computers with a network connector card, use the connector on the card.
7 microphone connector Use the pink connector to attach a personal computer microphone for voice or musical input into a sound or telephony program. On computers with a sound card, the microphone connector is on the card. 8 side L/R surround connector Use the gray connector to provide enhanced surround audio for computers with 7.1 speakers. On computers with a sound card, the microphone connector is on the card.
• If your computer is installed in a corner on a desk or under a desk, leave at least 5.1 cm (2 in) clearance from the back of the computer to the wall to permit the airflow required for proper ventilation.
• Do not install your computer in an enclosure that does not allow airflow. Restricting the airflow impacts your computer’s performance, possibly causing it to overheat. Setting Up a Printer NOTICE: Complete the operating system setup before you connect a printer to the computer. See the documentation that came with the printer for setup information, including how to: • Obtain and install updated drivers. • Connect the printer to the computer. • Load paper and install the toner or ink cartridge.
Printer Cable Your printer connects to your computer with either a USB cable or a parallel cable. Your printer may not come with a printer cable, so if you purchase a cable separately, ensure that it is compatible with your printer and computer. If you purchased a printer cable at the same time you purchased your computer, the cable may arrive in the computer’s shipping box. Connecting a USB Printer NOTE: You can connect USB devices while the computer is turned on.
3 Turn on the printer and then turn on the computer. 4 Depending on your computer’s operating system, a printer wizard may be available to help you install the printer driver: In Windows® XP, click Start→ Printers and Faxes→ Add a printer to start the Add Printer Wizard. In Windows Vista™, click Start the Add Printer Wizard. → Network→ Add a printer to start 5 Install the printer driver if necessary. See "Reinstalling Drivers and Utilities" on page 88 and the documentation that came with your printer.
To format CDs for storing data, to create music CDs, or to copy CDs, see the CD software that came with your computer. NOTE: Ensure that you follow all copyright laws when you create CDs.
Adjusting the Volume NOTE: When the speakers are muted, you do not hear the CD or DVD playing. 1 Open the Volume Control window. 2 Click and drag the bar in the Volume Control column and slide it up or down to increase or decrease the volume. For more information on volume control options, click Help in the Volume Control window.
Copying CDs and DVDs NOTE: Ensure that you observe all copyright laws when creating CDs or DVDs. This section applies only to computers that have a CD-RW, DVD+/-RW, or CD-RW/DVD (combo) drive. NOTE: The types of CD or DVD drives offered by Dell may vary by country. The following instructions explain how to make an exact copy of a CD or DVD using Roxio Creator Plus - Dell Edition.
• If you have two CD/DVD drives, select the drive into which you have inserted your source CD or DVD, and then click Disc Copy. The computer copies the data from the source CD or DVD to the blank CD or DVD. Once you have finished copying the source CD or DVD, the CD or DVD that you have created automatically ejects. Using Blank CDs and DVDs CD-RW drives can write to CD recording media only (including high-speed CD-RW media), while DVD-writable drives can write to both CD and DVD recording media.
Media Type Read Write Rewritable DVD-RW Yes Yes Yes DVD+R DL Yes Yes No DVD-R DL Maybe No No DVD-RAM Maybe No No Helpful Tips • After you start Roxio Creator Plus and open a Creator project, you can use Microsoft® Windows® Explorer to drag and drop files to a CD-R or CD-RW. • Use CD-Rs to burn music CDs that you want to play in regular stereos. CD-RWs may not play in many home or car stereos. • You cannot create audio DVDs with Roxio Creator Plus.
Using a Media Card Reader (Optional) Use the Media Card Reader to transfer data directly to your computer. The Media Card Reader supports the following memory types: • xD-Picture Card • SmartMedia (SMC) • CompactFlash Type I and II (CF I/II) • MicroDrive Card • SecureDigital Card (SD) • MultiMediaCard (MMC) • Memory Stick (MS/MS Pro) For information on installing a Media Card Reader, see "Installing a Media Card Reader" on page 138.
To use the Media Card Reader: 1 Check the media or card to determine the proper orientation for insertion. 2 Slide the media or card into the appropriate slot until it is completely seated in the connector. If you encounter resistance, do not force the media or card. Check the card orientation and try again. Connecting Two Monitors CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
1 2* 3* 4 *May not be present on your computer 1 optional DVI adapter 2 DVI (white) connector 3 TV-OUT connector 4 VGA (blue) connector Connecting One Monitor With a VGA Connector and One Monitor With a DVI Connector 1 Follow the procedures in "Before You Begin" on page 99. 2 Connect the VGA connector on the monitor to the VGA (blue) connector on the back of the computer. 3 Connect the DVI connector on the other monitor to the DVI (white) connector on the back of the computer.
3 Connect the other end of the S-video cable to the S-video input connector on your TV. 4 Connect the VGA or DVI monitor. Changing the Display Settings 1 After you connect the monitor(s) or TV, turn on the computer. The Microsoft® Windows® desktop displays on the primary monitor. 2 Enable clone mode or extended desktop mode in the display settings. • In clone mode, both monitors display the same image.
To set standby mode to automatically activate after a defined period of inactivity: 1 Click Start→ Control Panel→ Pick a category→ Performance and Maintenance. 2 Under or pick a Control Panel icon, click Power Options. To immediately activate standby mode without a period of inactivity, click Start→ Turn Off Computer→ Stand by. To exit from standby mode, press a key on the keyboard or move the mouse.
Power Options Properties Define your standby mode settings, hibernate mode settings, and other power settings in the Power Options Properties window. To access the Power Options Properties window: 1 Click Start→ Control Panel→ Pick a category→ Performance and Maintenance. 2 Under or pick a Control Panel icon, click Power Options. 3 Define your power settings on the Power Schemes tab, Advanced tab, and Hibernate tab. Power Schemes Tab Each standard power setting is called a scheme.
If you want to change the default settings for a scheme, click the drop-down menu in the Turn off monitor, Turn off hard disks, System stand by, or System hibernates field, and then select a time-out from the displayed list. Changing the time-out for a scheme field permanently changes the default settings for that scheme, unless you click Save As and enter a new name for the changed scheme. Advanced Tab The Advanced tab allows you to: • Place the power options icon access.
When the computer exits from a power conservation mode (Standby or Hibernate), the Windows desktop is restored to the state it was in before it entered the power conservation mode. Windows Vista has three main default power management modes: • Balanced • Power Saver • High Performance Dell has added a fourth, Dell-Recommended, mode that sets power management to the most typical settings for the majority of Dell customers. This is the active power plan.
To exit from standby mode, press a key on the keyboard or move the mouse. NOTICE: If your computer loses power while in standby mode, it may lose data. Windows Vista has a new feature called Hybrid Sleep mode - this saves the data into a file and also puts the system into standby. If you lose power, the system will have retained your data on the hard drive and resumes to the same state you left it. Go to Help and Support and search for hybrid sleep for further information.
To access the Power Plan Properties window: 1 Click Start and click Control Panel. 2 Under Pick a category, click System and Maintenance. 3 Under System and Maintenance, click Power Options. 4 This takes you to the main Select a Power Plan window. 5 In the Select A Power Plan window, you can change or modify power settings. To change the default settings for a plan: 1 Click Start and click Control Panel. 2 Under Pick a category, click System and Maintenance.
Enabling SpeedStep™ Technology SpeedStep technology controls your computer's processor performance automatically, dynamically adjusting the operating frequency and voltage, according to the task at hand. When an application does not require full performance, significant amounts of power can be saved. Performance is designed to still be responsive, with maximum processor performance being delivered when required, and automatic power savings when possible.
serial ATA RAID configured for RAID level 1 segment 1 segment 1 duplicated segment 2 segment 2 duplicated segment 3 segment 3 duplicated segment 4 segment 4 duplicated segment 5 segment 5 duplicated segment 6 segment 6 duplicated hard drive 1 hard drive 2 If a drive failure occurs, subsequent read and write operations are directed to the surviving drive. A replacement drive can then be rebuilt using the data from the surviving drive.
Utility. Both methods require that you set your computer to RAID-enabled mode before starting any of the RAID configuration procedures in this document. Setting Your Computer to RAID-Enabled Mode 1 Enter the system setup (see "Entering System Setup" on page 170). 2 Press the left- and right-arrow keys to highlight Drives tab. 3 Press the up- and down-arrow keys to highlight Drive Controller, then press . 4 Press the up- and down-arrow keys to highlight RAID On, and then press .
7 Select the desired capacity for the volume, and press . The default value is the maximum available size. 8 Press to create the volume. 9 Press to confirm that you want to create the RAID volume. 10 Confirm that the correct volume configuration is displayed on the main Intel Option ROM screen. 11 Use the up- and down-arrow keys to select Exit, and press . 12 Install the operating system.
• You already have a two-hard drive computer configured into an array, but you still have some space left on the array that you want to designate as a second RAID volume. Creating a RAID 1 Volume NOTE: When you perform this operation, all data on the RAID drives will be lost. 1 Set your computer to RAID-enabled mode (see "Setting Your Computer to RAID-Enabled Mode" on page 42).
Deleting a RAID Volume NOTE: While this procedure deletes the RAID 1 volume, it also splits the RAID 1 volume into two non-RAID hard drives with a partition, and leaves any existing data files intact. Deleting a RAID 0 volume, however, destroys all data on the volume. 1 In Windows XP, click Start→ All Programs→ Intel®Matrix Storage Manager→ Intel Matrix Storage Console to launch the Intel® Storage Utility.
6 From the drop-down box, select RAID 1 as the RAID level. NOTE: Select the hard drive that already has the data or operating system files that you want to maintain on the RAID volume as your source hard drive. 7 On the Select Source Hard Drive screen, double-click the hard drive from which you want to migrate, and click Next. 8 On the Select Member Hard Drive screen, double-click the hard drive to select the member drive that you want to act as the mirror in the array, and click Next.
Rebuilding a Degraded RAID 1 Volume If your computer does not have a spare hard drive, and the computer has reported a degraded RAID 1 volume, you can manually rebuild the computer’s redundancy mirror to a new hard drive by performing the following steps: 1 In Windows XP, click Start→ All Programs→ Intel®Matrix Storage Manager→ Intel Matrix Storage Console to launch the Intel® Storage Utility.
NOTE: You can transfer information from an old computer to a new computer by directly connecting a serial cable to the input/output (I/O) ports of the two computers. To transfer data over a serial connection, you must access the Network Connections utility from the Control Panel and perform additional configuration steps, such as setting up an advanced connection and designating the host computer and the guest computer.
5 On the Select a transfer method screen, click the transfer method you prefer. 6 On the What do you want to transfer? screen, select the items you want to transfer and click Next. After the information has been copied, the Completing the Collection Phase screen appears. 7 Click Finish. To transfer data to the new computer: 1 On the Now go to your old computer screen on the new computer, click Next.
6 When the disk creation completes and the Now go to your old computer message appears, do not click Next. 7 Go to the old computer. To copy data from the old computer: 1 On the old computer, insert the wizard disk. 2 Click Start→ Run. 3 In the Open field on the Run window, browse to the path for fastwiz (on the appropriate removable media) and click OK. 4 On the Files and Settings Transfer Wizard welcome screen, click Next. 5 On the Which computer is this? screen, click Old Computer→ Next.
NOTE: Access to the Dell™ Knowledge Base document may not be available in certain countries. Transferring Information using Windows Vista The Windows Vista operating system provides the Easy Transfer wizard to move data from a source computer to a new computer.
2 1 3 4 1 network adapter connector 2 network device 3 network adapter connector on computer 4 network cable Network Setup Wizard The Microsoft Windows operating system provides a Network Setup Wizard to guide you through the process of sharing files, printers, or an Internet connection between computers in a home or small office. Windows XP 1 Click Start, point to All Programs→ Accessories→ Communications, and then click Network Setup Wizard. 2 On the welcome screen, click Next.
Windows Vista 1 Click Start network. , and then click Connect to→ Set up a connection or 2 Select an option under Choose a connection option. 3 Click Next, and then follow the instructions in the wizard. For more information, access Help and Support, and use the search term network. Connecting to the Internet NOTE: ISPs and ISP offerings vary by country. To connect to the Internet, you need a modem or network connection and an Internet service provider (ISP).
Setting Up Your Internet Connection To set up an Internet connection with a provided ISP desktop shortcut: 1 Save and close any open files, and exit any open programs. 2 Double-click the ISP icon on the Windows Vista desktop. 3 Follow the instructions on the screen to complete the setup. If you do not have an ISP icon on your desktop or if you want to set up an Internet connection with a different ISP, perform the steps in the following section.
NOTE: If you do not know which type of connection to select, contact your ISP. 7 Use the setup information provided by your ISP to complete the setup. Windows Vista NOTE: Have your ISP information ready. If you do not have an ISP, the Connect to the Internet wizard can help you get one. 1 Save and close any open files, and exit any open programs. 2 Click Start , and click Control Panel 3 Under Network and Internet, click Connect to the Internet. The Connect to the Internet window appears.
Setting Up and Using Your Computer
Solving Problems CAUTION: Some of the parts described in this chapter may be replaceable by a certified service technician only and are not customer replaceable. Troubleshooting Tips Follow these tips when you troubleshoot your computer: • If you added or removed a part before the problem started, review the installation procedures and ensure that the part is correctly installed. • If a peripheral device does not work, ensure that the device is properly connected.
Drive Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. ENSURE THAT MICROSOFT® WINDOWS® RECOGNIZES THE DRIVE — Windows XP • Click Start and click My Computer. Windows Vista™ • Click Start and click Computer. If the drive is not listed, perform a full scan with your antivirus software to check for and remove viruses.
Optical drive problems NOTE: High-speed optical drive vibration is normal and may cause noise, which does not indicate a defect in the drive or the CD or DVD. NOTE: Because of different regions worldwide and different disc formats, not all DVD titles work in all DVD drives. ADJUST THE WINDOWS VOLUME CONTROL — • Click the speaker icon in the lower-right corner of your screen. • Ensure that the volume is turned up by clicking the slidebar and dragging it up.
Hard drive problems RUN CHECK DISK — Windows XP 1 Click Start and click My Computer. 2 Right-click Local Disk C:. 3 Click Properties→ Tools→ Check Now. 4 Click Scan for and attempt recovery of bad sectors and click Start. Windows Vista 1 Click Start and click Computer. 2 Right-click Local Disk C:. 3 Click Properties→ Tools→ Check Now. The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to continue the desired action.
CHECK THE TELEPHONE LINE CONNECTION CHECK THE TELEPHONE JACK CONNECT THE MODEM DIRECTLY TO THE TELEPHONE WALL JACK USE A DIFFERENT TELEPHONE LINE — • Verify that the telephone line is connected to the jack on the modem. (The jack has either a green label or a connector-shaped icon next to it.) • Ensure that you feel a click when you insert the telephone line connector into the modem. • Disconnect the telephone line from the modem and connect it to a telephone. Listen for a dial tone.
VE R I F Y T H A T T H E M O D E M I S C O M M U N I C A T I N G W I T H W I N D O W S — Windows XP 1 Click Start→ Control Panel→ Printers and Other Hardware→ Phone and Modem Options→ Modems. 2 Click the COM port for your modem→ Properties→ Diagnostics→ Query Modem to verify that the modem is communicating with Windows. If all commands receive responses, the modem is operating properly. Windows Vista 1 Click Start → Control Panel→ Hardware and Sound→ Phone and Modem Options→ Modems.
Error Messages If the message is not listed, see the documentation for the operating system or the program that was running when the message appeared. A FILENAME CANNOT CONTAIN ANY OF THE FOLLOWING CHARACTERS: \ / : * ? “ < > | — Do not use these characters in filenames. A R E Q U I R E D . D L L F I L E W A S N O T F O U N D — The program that you are trying to open is missing an essential file.
O P E R A T I N G S YS T E M N O T F O U N D — Contact Dell (see "Contacting Dell" on page 183). Keyboard Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. CHECK THE KEYBOARD CABLE — • Ensure that the keyboard cable is firmly connected to the computer.
Lockups and Software Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. The computer does not start up Ensure that the power cable is firmly connected to the computer and to the electrical outlet. The computer stops responding NOTICE: You might lose data if you are unable to perform an operating system shutdown.
A program is designed for an earlier Microsoft® Windows® operating system RUN THE PROGRAM COMPATIBILITY WIZARD — Windows XP The Program Compatibility Wizard configures a program so that it runs in an environment similar to non-XP operating system environments. 1 Click Start→ All Programs→ Accessories→ Program Compatibility Wizard→ Next. 2 Follow the instructions on the screen.
Other software problems CHECK THE SOFTWARE DOCUMENTATION OR CONTACT THE SOFTWARE MANUFACTURER FOR TROUBLESHOOTING INFORMATION — • Ensure that the program is compatible with the operating system installed on your computer. • Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation for information. • Ensure that the program is installed and configured properly. • Verify that the device drivers do not conflict with the program.
Media Card Reader Problems NO DRIVE LETTER IS ASSIGNED — When Windows detects the Media Card Reader, the device is automatically assigned a drive letter as the next logical drive after all other physical drives in the system. If the next logical drive after the physical drives is mapped to a network drive, Windows does not automatically assign a drive letter to the Media Card Reader. To manually assign a drive for the Media Card Reader: Windows XP 1 Click Start.
FLEXBAY DEVICE IS DISABLED — There is a FlexBay disable option in the BIOS setup that appears only when the FlexBay device is installed. If the FlexBay device is physically installed, but it is not running, check to see if it is enabled in the BIOS setup. Memory Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Mouse Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. C L E A N T H E M O U S E — See "Mouse" on page 179 for instructions on cleaning the mouse. CHECK THE MOUSE CABLE — 1 Remove mouse extension cables, if used, and connect the mouse directly to the computer. 2 Reconnect the mouse cable as shown on the setup diagram for your computer. RESTART THE COMPUTER — 1 Simultaneously press to display the Start menu.
R E I N S T A L L T H E M O U S E D R I V E R — See "Reinstalling Drivers and Utilities" on page 88. R U N T H E H A R D W A R E TR O U B L E S H O O T E R — See "Restoring Your Operating System" on page 91. Network Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Power Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. I F T H E P O W E R L I G H T I S O F F — The computer is either turned off or is not receiving power. • Reseat the power cable into both the power connector on the back of the computer and the electrical outlet. • If the computer is plugged into a power strip, ensure that the power strip is plugged into an electrical outlet and that the power strip is turned on.
E L I M I N A T E I N T E R F E R E N C E — Some possible causes of interference are: • Power, keyboard, and mouse extension cables • Too many devices on a power strip • Multiple power strips connected to the same electrical outlet Printer Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTE: If you need technical assistance for your printer, contact the printer’s manufacturer.
VE R I F Y T H A T T H E P R I N T E R I S R E C O G N I Z E D B Y W I N D O W S — Windows XP 1 Click Start→ Control Panel→ Printers and Other Hardware→ View installed printers or fax printers. 2 If the printer is listed, right-click the printer icon. 3 Click Properties→ Ports. For a parallel printer, ensure that the Print to the following port(s): setting is LPT1 (Printer Port). For a USB printer, ensure that the Print to the following port(s): setting is USB.
CHECK THE CABLE CONNECTIONS — • See the scanner documentation for cable connection information. • Ensure that the scanner cables are securely connected to the scanner and the computer. VE R I F Y T H A T T H E S C A N N E R I S R E C O G N I Z E D B Y M I C R O S O F T W I N D O W S — Windows XP 1 Click Start→ Control Panel→ Printers and Other Hardware→ Scanners and Cameras. 2 If your scanner is listed, Windows recognizes the scanner.
E N S U R E T H A T T H E S U B W O O F E R A N D T H E S P E A K E R S A R E T U R N E D O N — See the setup diagram supplied with the speakers. If your speakers have volume controls, adjust the volume, bass, or treble to eliminate distortion. A D J U S T T H E W I N D O W S V O L U M E C O N T R O L — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume is turned up and that the sound is not muted.
ENSURE THAT THE CORRECT AUDIO SOLUTION IS ENABLED IN THE BIOS SETUP P R O G R A M — See "System Setup" on page 170. Video and Monitor Problems CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTE: See the monitor documentation for troubleshooting procedures. If the screen is blank CHECK THE MONITOR CABLE CONNECTION — • Ensure that the graphics cable is connected as shown on the setup diagram for your computer.
If the screen is difficult to read C H E C K T H E M O N I T O R S E T T I N G S — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing (degaussing) the monitor, and running the monitor self-test. M O V E T H E S U B W O O F E R A W A Y F R O M T H E M O N I T O R — If your speaker system includes a subwoofer, ensure that the subwoofer is at least 60 cm (2 ft) away from the monitor.
Troubleshooting Tools Power Lights CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. The power button light (bi-color LED) located on the front of the computer illuminates and blinks or remains solid to indicate different states: • • • If the power light is off, the computer is either turned off or is not receiving power. – Reseat the power cable in the power connector on the back of the computer and the electrical outlet.
• • If the power light is blinking amber, the computer is receiving electrical power, a device might be malfunctioning or incorrectly installed. – Remove and then reinstall the memory modules (see "Memory" on page 111). – Remove and then reinstall any cards (see "Cards" on page 115). – Remove and then reinstall the graphics card, if applicable (see "Cards" on page 115). If the power light is steady amber, there may be a power problem or an internal device malfunction.
Code Description (repetitive short beeps) Suggested Remedy 1 BIOS checksum failure. Possible motherboard failure. Contact Dell. 2 No memory modules are detected If you have two or more memory modules installed, remove the modules, reinstall one module (see "Installing Memory" on page 112), and then restart the computer. If the computer starts normally, reinstall an additional module. Continue until you have identified a faulty module or reinstalled all modules without error.
System Messages NOTE: If the message you received is not listed in the table, see the documentation for either the operating system or the program that was running when the message appeared. A L E R T ! P R E V I O U S A T T E M P T S A T B O O T I N G T H I S S YS T E M H A V E F A I L E D A T CHECKPOINT [NNNN].
N O B O O T D E V I C E A V A I L A B L E — No bootable partition on hard drive, no bootable floppy in floppy driver, the hard drive or floppy cable is loose, or no bootable device exists. • If the floppy drive is your boot device, ensure that a bootable floppy disk is in the drive. • If the hard drive is your boot device, ensure that the cables are connected and that the drive is installed properly and partitioned as a boot device.
Dell Diagnostics CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. When to Use the Dell Diagnostics If you experience a problem with your computer, perform the checks in Lockups and Software Problems (see "Lockups and Software Problems" on page 65) and run the Dell Diagnostics before you contact Dell for technical assistance. It is recommended that you print these procedures before you begin.
Starting the Dell Diagnostics From the Drivers and Utilities Media 1 Insert the Drivers and Utilities media. 2 Shut down and restart the computer. When the DELL logo appears, press immediately. NOTE: If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop; then, shut down your computer and try again. NOTE: The next steps change the boot sequence for one time only.
2 After you have selected the Test System option from the main menu, the following menu appears: NOTE: It is recommended that you select Extended Test from the menu below to run a more thorough check of devices in the computer. Option Function Express Test Performs a quick test of devices in the system. This typically can take 10 to 20 minutes. Extended Test Performs a thorough check of devices in the system. This typically can take an hour or more.
Tab Function Configuration Displays your hardware configuration for the selected device. The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various internal tests, and it displays the information in the device list in the left pane of the screen. The device list may not display the names of all the components installed on your computer or all devices attached to your computer. Parameters Allows you to customize the test by changing the test settings.
Identifying Drivers If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver. Windows XP 1 Click Start and click Control Panel. 2 Under Pick a Category, click Performance and Maintenance→ System→ Hardware→ Device Manager. 3 Scroll down the list of devices and check for an exclamation point (a circle with a [!]) next to the device name.
Windows XP 1 Click Start and click Control Panel. 2 Under Pick a Category→ Performance and Maintenance→ System→ System Properties→ Hardware→ Device Manager. 3 Right-click the device for which the new driver was installed, then click Properties. 4 Click Driver and click Roll Back Driver. Windows Vista 1 Click Start → Computer→ System Properties→ Device Manager. NOTE: The User Account Control window may appear.
5 At the Welcome Dell System Owner screen, click Next. NOTE: The Drivers and Utilities media displays drivers only for hardware that came installed in your computer. If you installed additional hardware, the drivers for the new hardware might not be displayed by the Drivers and Utilities media. If those drivers are not displayed, exit the Drivers and Utilities media program. For drivers information, see the documentation that came with the device.
Windows Vista 1 Click Start → Computer→ System Properties→ Device Manager. NOTE: The User Account Control window may appear. If you are an administrator on the computer, click Continue; otherwise, contact your administrator to enter the Device Manager. 2 Double-click the type of device for which you are installing the driver (for example, Audio or Video). 3 Double-click the name of the device for which you are installing the driver. 4 Click Driver→ Update Driver→ Browse my computer for driver software.
Using Microsoft Windows System Restore The Windows operating systems provide a System Restore option which allows you to return your computer to an earlier operating state (without affecting data files) if changes to the hardware, software, or other system settings have left the computer in an undesirable operating state. Any changes that System Restore makes to your computer are completely reversible. NOTICE: Make regular backups of your data files.
Undoing the Last System Restore NOTICE: Before you undo the last system restore, save and close all open files and exit any open programs. Do not alter, open, or delete any files or programs until the system restoration is complete. Windows XP 1 Click Start→ All Programs→ Accessories→ System Tools→ System Restore. 2 Click Undo my last restoration and click Next. Windows Vista 1 Click Start . 2 In the Start Search box, type System Restore and press . 3 Click Undo my last restoration and click Next.
the computer. Any programs or files added since you received your computer—including data files—are permanently deleted from the hard drive. Data files include documents, spreadsheets, e-mail messages, digital photos, music files, and so on. If possible, back up all data before using PC Restore or Factory Image Restore. Windows XP: Dell PC Restore Using PC Restore: 1 Turn on the computer. During the boot process, a blue bar with www.dell.com appears at the top of the screen.
Dell PC Restore enables you to restore your hard drive to the operating state it was in when you purchased your computer. It is recommended that you do not remove PC Restore from your computer, even to gain additional harddrive space. If you remove PC Restore from the hard drive, you cannot ever recall it, and you will never be able to use PC Restore to return your computer operating system to its original state. 1 Log on to the computer as a local administrator.
4 To access the recovery options, log on as a local user. To access the command prompt, type administrator in the User name field, then click OK. 5 Click Dell Factory Image Restore. NOTE: Depending upon your configuration, you may need to select Dell Factory Tools, then Dell Factory Image Restore. The Dell Factory Image Restore welcome screen appears. 6 Click Next. The Confirm Data Deletion screen appears. NOTICE: If you do not want to proceed with Factory Image Restore, click Cancel.
NOTE: The Dell Drivers and Utilities media contains drivers that were installed during the assembly of the computer. Use the Dell Drivers and Utilities media to load any required drivers. Depending on the region from which you ordered your computer, or whether you requested the media, the Dell Drivers and Utilities media and Operating System media may not ship with your computer. Reinstalling Windows XP or Windows Vista The reinstallation process can take 1 to 2 hours to complete.
Windows XP 1 Click Start and click Help and Support. 2 Type hardware troubleshooter in the Search field and click the arrow to start the search. 3 Click Hardware Troubleshooter in the Search Results list. 4 In the Hardware Troubleshooter list, click I need to resolve a hardware conflict on my computer, and click Next. Windows Vista 1 Click Start and click Help and Support. 2 Type hardware troubleshooter in the search field and press to start the search.
Removing and Installing Parts CAUTION: Some of the parts described in this chapter may be replaceable by a certified service technician only and are not customer replaceable. Before You Begin This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that the following conditions exist: • You have performed the steps in "Turning Off Your Computer" on page 100 and "Before Working Inside Your Computer" on page 100.
Turning Off Your Computer NOTICE: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 1 Save and close any open files and exit any open programs. 2 Shut down the operating system: • In Windows XP, click Start→ Turn Off Computer→ Turn off. • In Windows Vista, click Start Shut Down. , click the arrow , and then click The computer turns off after the operating system shutdown process finishes.
NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 1 Disconnect all telephone or network cables from the computer. 2 Disconnect your computer and all attached devices from their electrical outlets. 3 Press the power button to ground the system board. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. 4 Remove the computer cover.
2 1 1 computer cover 2 screws (2) 4 Release the computer cover by pulling it away from the front of the computer and lifting it up. 5 Set the cover aside in a secure location. Removing the Support Bracket CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover. See "Removing the Computer Cover" on page 101.
6 Set it aside in a secure location.
Inside View of Your Computer CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
System Board Components 31 1 2 3 4 5 30 6 7 29 8 28 27 9 26 10 11 25 12 24 13 23 22 14 21 20 19 18 17 16 15 1 processor socket (CPU) 2 processor fan connector (CPU_FAN) 3 memory module connectors (DIMM_1) 4 memory module connectors (DIMM_2) 5 memory module connectors (DIMM_3) 6 memory module connectors (DIMM_4) Removing and Installing Parts 105
7 main power connector (ATX_POWER) 8 floppy drive connector (FLOPPY) battery socket 10 serial ATA drive connectors (SATA0) 11 serial ATA drive connectors (SATA1) 12 CMOS jumper (CLEAR CMOS) 13 password jumper (CLEAR_PW) 14 front panel connector (F_PANEL) 15 serial ATA drive connectors (SATA4) 16 front USB connector (F_USB1) 17 serial ATA drive connectors (SATA5) 18 front USB connector (F_USB2) 19 front FlexBay connector (F_USB3) 20 system fan connector (SYS_FAN1) 21 front audio (F_AUDIO) 22
Power Supply DC Connector Pin Assignments DC Power Connector P1 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 Removing and Installing Parts 107
Pin Number Signal name Wire Color Wire Size 1 3.3 V Orange 20 AWG 2 3.3 V Orange 20 AWG 3 RTN Black 20 AWG 4 5V Red 20 AWG 5 RTN Black 20 AWG 6 5V Red 20 AWG 7 RTN Black 20 AWG 8 POK Gray 22 AWG 9 5 V AUX Purple 20 AWG 10 +12 V Yellow 20 AWG 11 +12 V Yellow 20 AWG 12 3.3 V Orange 20 AWG 13 3.
DC Power Connector P2 3 1 4 2 Pin Number Signal Name 18-AWG Wire 1 GND Black 2 GND Black 3 +12 VADC Yellow 4 +12 VADC Yellow DC Power Connectors P3, P5, and P6 Pin Number Signal name 18-AWG Wire 1 +3.
DC Power Connector P4 Pin Number Signal Name 22-AWG Wire 1 +5 VDC Red 2 GND Black 3 GND Black 4 +12 VADC Yellow DC Power Connector P7 6 5 4 3 2 1 Pin Signal Name 18-AWG Number Wire N/C 1 2 COM Black 3 COM Black 4 +3.
Memory You can increase your computer memory by installing memory modules on the system board. Your computer supports DDR2 memory. For additional information on the type of memory supported by your computer, see "Memory" on page 165. NOTICE: Do not install ECC or buffered memory modules. Only unbuffered, nonECC memory is supported. Memory Installation Guidelines • DIMM connectors must be populated in numerical order beginning with connectors DIMM_1 and DIMM_2, then connectors DIMM_3 and DIMM_4.
1 2 1 Pair A: matched pair of memory modules in connectors DIMM_1 and DIMM_2 2 Pair B: matched pair of memory modules in connectors DIMM_3 and DIMM_4 NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new memory module. Otherwise, your computer may not start properly.
1 Follow the procedures in "Before You Begin" on page 99. 2 Press the securing clip at each end of the memory module connector. 1 2 3 1 memory connector closest from processor (DIMM_1) 3 connector 2 securing clips (2) 3 Align the notch on the bottom of the module with the crossbar in the connector.
NOTICE: To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module. 4 Insert the module into the connector until the module snaps into position. If you insert the module correctly, the securing clips snap into the cutouts at each end of the module. 5 Replace the PCI Express x16 card. See "Cards" on page 115. 6 Replace the computer cover.
NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components. You can do so by touching an unpainted metal surface on the computer chassis. 1 Follow the procedures in "Before You Begin" on page 99. 2 Press out the securing clip at each end of the memory module connector. 3 Grasp the module at the end of the board and lift up. 4 Replace the PCI Express x16 card. See "Cards" on page 115.
• If you are removing but not replacing a card, see "Removing a PCI/PCI Express Card" on page 120. • If you are replacing a card, remove the current driver for the card from the operating system. Installing a PCI/PCI Express Card 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover. See"Removing the Computer Cover" on page 101.
5 If you are replacing a card that is already installed in the computer, remove the card. If necessary, disconnect any cables connected to the card. • For PCI card, grasp the card by its top corners, and ease it out of its connector. • For PCI Express card, pull the securing tab, grasp the card by its top corners, and then ease it out of its connector.
3 2 4 5 1 6 1 alignment bar 2 fully-seated card 3 not fully-seated card 4 bracket within slot 5 bracket caught outside of slot 6 alignment guide 8 Replace the support bracket (see "Replacing the Support Bracket" on page 161) and then press down the card retention bracket to seat it on its slot. 9 Ensure that: • The guide clamp is aligned with the guide notch. • The tops of all cards and filler brackets are flush with the alignment bar.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. NOTICE: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 1 2 3 4 1 card retention release lever 2 card retention bracket 3 PCI card 4 PCI card slot 11 Replace the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on.
13 If you installed an add-in network adapter and want to disable the integrated network adapter: a Enter system setup (see "System Setup" on page 170), go to Onboard Devices and select Integrated NIC, and then change the setting to Off. b Connect the network cable to the add-in network adapter’s connectors. Do not connect the network cable to the integrated connector on the back panel. See "Back Panel Connectors" on page 18.
8 Replace the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on. 9 Remove the card’s driver from the operating system. 10 If you removed a sound card: a Enter system setup (see "System Setup" on page 170), go to Onboard Devices and select Integrated Audio and then change the setting to On. b Connect external audio devices to the audio connectors on the back panel of the computer. See "Back Panel Connectors" on page 18.
Removing the Bezel 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover (see "Removing the Computer Cover" on page 101). 1 4 2 3 1 bottom tabs (3) 2 top tabs (3) 3 bezel 4 tab slots 3 Grasp and lift the top tabs one at a time to release the bezel from the front panel. 4 Lift the bezel out of the bottom tabs. 5 Set the bezel aside in a secure location.
Replacing the Bezel 1 Align and insert the bottom tabs into the front panel hinges. 1 2 3 1 bottom tabs (3) 2 top tabs (3) 3 bezel 2 Rotate the bezel toward the computer until the three top tabs snap into place on the front panel.
Drives Your computer supports a combination of these devices: • Up to two serial ATA hard drives • One optional floppy drive or an optional Media Card Reader • One optical drive 1 2 3 4 1 power supply 2 hard drive 4 optical drive 5 floppy drive or Media Reader 5 3 support bracket Recommended Drive Cable Connections 124 • Connect serial ATA hard drives to connectors labeled "SATA0" or "SATA1" on the system board.
Connecting Drive Cables When you install a drive, you connect two cables—a DC power cable and a data cable—to the back of the drive. 3 1 2 1 power cable 2 power input connector 3 data cable Drive Interface Connectors The drive cable connectors are keyed for correct insertion. Properly align the cable connector key on the cable and the drive before connecting.
Connecting and Disconnecting Drive Cables When connecting and disconnecting a serial ATA data cable, disconnect the cable using the pull-tab. The serial ATA interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other connector. Hard Drives CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
6 1 2 5 4 3 1 hard drive 2 serial ATA data cable 3 power cable 4 system board connector 5 securing tab 6 shoulder screws (4) 6 Press in on the securing tab on the side of the drive and slide the drive up and out. 7 If removing this drive changes the drive configuration, then be sure to reflect these changes in system setup.
Installing a Hard Drive 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover (see "Removing the Computer Cover" on page 101). 3 Remove the support bracket (see "Removing the Support Bracket" on page 102). 4 Check the documentation for the drive to verify that it is configured for your computer. 5 Attach the shoulder screws to the hard drive. 1 2 1 hard drive 2 shoulder screws (4) 6 Connect the power and data cables to the drive.
10 Replace the support bracket (see "Replacing the Support Bracket" on page 161). 11 Replace the computer cover (see "Replacing the Computer Cover" on page 162). NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer. 12 Connect your computer and devices to electrical outlets, and then turn them on. 13 See the documentation that came with the drive for instructions on installing any software required for drive operation.
1 2 1 second hard drive (optional) 2 shoulder screws (4) 6 Connect the power and data cables to the drive. 7 Connect the data cable to the system board. 8 Slide the hard drive into the hard drive bay until it snaps in place. 9 Check all cables to be certain that they are properly connected and firmly seated. 10 Replace the support bracket (see "Replacing the Support Bracket" on page 161). 11 Replace the computer cover (see "Replacing the Computer Cover" on page 162).
Floppy Drive CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. NOTE: If you are adding a floppy drive, see "Installing a Floppy Drive" on page 133. Removing a Floppy Drive 1 Follow the procedures in "Before You Begin" on page 99.
7 Press the two spring clamps and slide out the floppy drive along with the FlexBay drive cage from the FlexBay slot. 8 Remove the two screws holding the floppy drive in the FlexBay drive cage. 1 2 1 screws (2) 2 FlexBay drive cage 9 Lift the floppy drive to separate it from the FlexBay drive cage. 10 Slide the FlexBay drive cage in the FlexBay slot till it snaps in place. 11 Install the FlexBay drive insert (see "Replacing the FlexBay Drive Panel Insert" on page 136).
Installing a Floppy Drive 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover (see "Removing the Computer Cover" on page 101). 3 Remove the bezel (see "Removing the Bezel" on page 122). 4 Remove the optical drive (see "Removing an Optical Drive" on page 140). 5 Remove the FlexBay drive insert (see "Removing the FlexBay Drive Panel Insert" on page 135). 6 Press the two spring clamps and slide out the FlexBay drive cage from the front of the system.
8 Tighten the two screws on the other side to secure the floppy drive in the FlexBay drive cage. 9 Slide the FlexBay drive cage along with the floppy drive in the FlexBay slot till it snaps in place. 10 Attach the power and data cables to the floppy drive. 11 Connect the other end of the data cable to the connector labeled "FLOPPY" on the system board (see "System Board Components" on page 105).
16 Connect your computer and devices to their electrical outlets, and turn them on. See the documentation that came with the drive for instructions on installing any software required for drive operation. 17 Enter system setup (see "System Setup" on page 170) and select the appropriate Diskette Drive option. 18 Verify that your computer works correctly by running the Dell Diagnostics (see "Dell Diagnostics" on page 84).
Replacing the FlexBay Drive Panel Insert 1 2 1 drive panel insert (optional) 2 slot 1 Slide the drive panel insert tab into the slot on the bezel. 2 Push the panel insert towards the bezel till it snaps in place. NOTE: To comply with FCC regulations, it is recommended that you replace the drive panel insert whenever the floppy drive is removed from the computer.
3 Remove the bezel (see "Removing the Bezel" on page 122). 4 Remove the optical drive (see "Removing an Optical Drive" on page 140). 5 Disconnect the FlexBay USB cable and the power cable from the back of the Media Card Reader and from the internal USB connector on the system board (see "System Board Components" on page 105). 6 Press the two spring clamps and slide out the Media Card Reader along with the FlexBay drive cage from the FlexBay slot.
10 If you are not reinstalling the Media Card Reader, replace the drive panel insert, as needed. 11 Replace the optical drive (see "Installing an Optical Drive" on page 141). 12 Replace the bezel (see "Replacing the Bezel" on page 123). 13 Replace the computer cover (see "Replacing the Computer Cover" on page 162). 14 Connect your computer and devices to electrical outlets, and then turn them on. Installing a Media Card Reader 1 Follow the procedures in "Before You Begin" on page 99.
*Not present on all computers. 1 1 Media Card Reader 12 Replace the optical drive (see "Installing an Optical Drive" on page 141). 13 Replace the bezel (see "Replacing the Bezel" on page 123). 14 Replace the computer cover (see "Replacing the Computer Cover" on page 162). 15 Connect your computer and devices to electrical outlets, and then turn them on. Optical Drive CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide.
Removing an Optical Drive 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover (see "Removing the Computer Cover" on page 101). 3 Remove the bezel (see "Removing the Bezel" on page 122). 4 Disconnect the optical drive data cable from the system board connector. 5 Disconnect the power cable and the optical drive data cable from the back of the drive. 6 Pull the optical drive bay release lever gently and slide the optical drive out through the front of the computer.
8 Replace the bezel (see "Replacing the Bezel" on page 123). 9 Replace the computer cover (see "Replacing the Computer Cover" on page 162). 10 Connect your computer and devices to electrical outlets, and then turn them on. 11 Configure the drives in system setup (see "Entering System Setup" on page 170). Installing an Optical Drive 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover (see "Removing the Computer Cover" on page 101).
5 Gently slide the drive into the optical drive bay till it snaps in place. 1 1 optical drive 6 Connect the power and data cables to the drive. 7 Connect the data cable to the system board connector on the system board. 8 Replace the bezel (see "Replacing the Bezel" on page 123). 9 Replace the computer cover (see "Replacing the Computer Cover" on page 162). 10 Connect your computer and devices to their electrical outlets, and turn them on.
Battery Replacing the Battery CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components. You can do so by touching an unpainted metal surface on the computer chassis. A coin-cell battery maintains computer configuration, date, and time information.
2 1 1 battery release lever 2 battery (positive side) 8 Replace the computer cover (see "Replacing the Computer Cover" on page 162). 9 Replace the support bracket (see "Replacing the Support Bracket" on page 161). NOTICE: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 10 Connect your computer and devices to electrical outlets, and then turn them on.
Power Supply CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer’s electronic components. You can do so by touching an unpainted metal surface on the computer chassis. Replacing the Power Supply 1 Follow the procedures in "Before You Begin" on page 99.
2 1 1 power supply 2 screws (3) 8 Slide out the power supply and lift it out. 9 Slide the replacement power supply toward the back of the computer. 10 Replace and tighten all screws that secure the power supply to the back of the computer chassis. CAUTION: Failure to replace and tighten all screws may cause electrical shock as these screws are a key part of the system grounding. NOTICE: Route the DC power cables under the chassis tabs.
15 Replace the computer cover (see "Replacing the Computer Cover" on page 162). 16 Connect your computer and devices to an electrical outlet, and turn them on. 17 Verify that the computer works correctly by running the Dell Diagnostics (see "Dell Diagnostics" on page 84). I/O Panel CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
1 2 1 I/O panel 2 screw Installing the I/O Panel 1 Place the I/O panel into the slot. NOTICE: Take care not to damage the cable connectors and the cable routing clips when sliding the I/O panel into the computer. 2 Replace and tighten the screw that secures the I/O panel to the chassis. 3 Reconnect the cables to the system board. 4 Replace the bezel (see "Replacing the Bezel" on page 123). 5 Replace the computer cover (see "Replacing the Computer Cover" on page 162).
1 1 I/O panel Processor Fan CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. CAUTION: The heat sink assembly, power supply, and other components may be very hot during normal operation. Be sure that they have had sufficient time to cool before you touch them.
Removing the Processor Fan/Heat Sink Assembly NOTICE: Do not touch the fan blades when you are removing the processor fan/heat sink assembly. This could damage the fan. 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover (see "Removing the Computer Cover" on page 101). 3 Disconnect the processor fan cable from the system board (see "System Board Components" on page 105). 4 Carefully move away any cables that are routed over the processor fan/heat sink assembly.
Installing the Processor Fan/Heat Sink Assembly NOTICE: When reinstalling the fan, ensure that you do not pinch the wires that run between the system board and the fan. 1 Align the captive screws on the processor fan/heat sink assembly to the four metal screw hole projections on the system board. 1 2 1 captive screws (4) 2 processor fan/heat sink assembly NOTE: The processor fan/heat sink assembly in your computer may not look exactly like the one shown in the illustration above.
Processor CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. Removing the Processor 1 Follow the procedures in "Before You Begin" on page 99. 2 Remove the computer cover (see "Removing the Computer Cover" on page 101). CAUTION: Despite having a plastic shield, the heat sink assembly may be very hot during normal operation. Be sure that it has had sufficient time to cool before you touch it.
1 2 3 4 1 processor cover 2 processor 3 socket 4 release lever NOTICE: When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket. 5 Gently remove the processor from the socket. Leave the release lever extended in the release position so that the socket is ready for the new processor. Installing the Processor NOTICE: Ground yourself by touching an unpainted metal surface on the back of the computer.
NOTICE: When replacing the processor, do not touch any of the pins inside the socket or allow any objects to fall on the pins in the socket. 1 Follow the procedures in "Before You Begin" on page 99. 2 Unpack the new processor, being careful not to touch the underside of the processor. NOTICE: You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer.
2 1 3 4 9 5 6 8 1 processor cover 7 2 tab 3 processor 4 processor socket 5 center cover latch 6 release lever 7 front alignment-notch 8 processor pin-1 indicator 9 rear alignment notch 9 Clean the thermal grease from the bottom of the heat sink. NOTICE: Ensure that you apply new thermal grease. New thermal grease is critical for ensuring adequate thermal bonding, which is a requirement for optimal processor operation. 10 Apply the new thermal grease to the top of the processor.
Chassis Fan CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. CAUTION: The heat sink assembly, power supply, and other components may be very hot during normal operation. Be sure that they have had sufficient time to cool before you touch them.
1 1 screw 4 Slide the chassis fan towards the front of the computer and lift it up.
Replacing the Chassis Fan 1 Follow the procedures in "Before You Begin" on page 99. 1 1 screw 2 Remove the computer cover (see "Removing the Computer Cover" on page 101). 3 Slide the chassis fan in place towards the back of the computer. 4 Tighten the screw to secure the chassis fan.
System Board Removing the System Board CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. CAUTION: The heat sink assembly, power supply, and other components may be very hot during normal operation. Be sure that they have had sufficient time to cool before you touch them. NOTICE: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer.
System Board Screws 1 2 1 screws (8) 2 system board Place the system board assembly that you just removed next to the replacement system board to compare and ensure they are identical. Installing the System Board 1 Gently align the board into the chassis and slide it toward the back of the computer. 2 Using the eight screws, secure the system board to the chassis. 3 Replace the cables that you removed from the system board.
4 Replace the processor and the heat sink (see "Installing the Processor" on page 153). NOTICE: Ensure that the processor fan/heat sink assembly is correctly seated and secure. 5 Replace the memory modules into the memory sockets at the same locations from which you removed them (see "Memory purchased from Dell is covered under your computer warranty." on page 112). 6 Replace any add-in cards on the system board. 7 Replace the computer cover (see "Replacing the Computer Cover" on page 162).
1 2 3 1 support bracket 2 card retention release lever 3 card retention bracket Replacing the Computer Cover CAUTION: Before you begin any of the procedures in this section, follow the safety instructions located in the Product Information Guide. 1 Ensure that all cables are connected, and fold cables out of the way. 2 Ensure that no tools or extra parts are left inside the computer. 3 Align the tabs at the bottom of the computer cover with the slots located along the edge of the computer.
5 Ensure that the cover is seated correctly. 6 Replace and tighten the two screws that secure the computer cover. 3 1 2 4 1 computer cover tab 2 slot 3 screws (2) 4 computer cover 7 Move the computer to the upright position. NOTICE: To connect a network cable, first plug the cable into the network device and then plug it into the computer. NOTICE: Ensure that none of the system air vents are blocked.
Removing and Installing Parts
Appendix Specifications Processor Processor type Intel® Core™ 2 Duo processor Intel® Pentium® Dual-Core processor Intel® Celeron® processor Level 2 (L2) cache At least 512 KB pipelined-burst, eight-way set associative, writeback SRAM Memory Type 667-MHz, 800-MHz DDR2 SDRAM Memory connectors four Memory capacities 512 MB, 1 GB or 2 GB Minimum memory 512 MB Maximum memory 4 GB Computer Information Chipset ICH9 and Intel G33 RAID Support RAID 1 (Mirroring) DMA channels seven Interrupt level
Audio Type Realtec ALC888 (7.1 Channel audio) Expansion Bus Bus type PCI 2.3 PCI Express 1.0A SATA 1.0 and 2.0 USB 2.0 Bus speed PCI: 133 MB/s PCI Express: x1 slot bidirectional speed - 500 MB/s x16 slot bidirectional speed - 8GB/s SATA: 1.5 Gbps and 3.0 Gbps USB: 480 Mbps high speed, 12 Mbps full speed, 1.
Drives Externally accessible: one 3.5-inch drive bay (FlexBay) one 5.25-inch drive bay Internally accessible two 3.5-inch drive bays Available devices two 3.5-inch Serial ATA hard drives and one 5.25-inch Serial ATA CD-ROM, CD-RW, DVD-ROM, DVD-RW, or combo drive (optional) 3.5-inch floppy drive (optional) or Media Card Reader (optional) Connectors External connectors: Video 15-hole connector Network adapter RJ-45 connector USB two front-panel and four back-panel USB 2.
Connectors Processor one 775-pin connector Memory four 240-pin connectors Power 12V one 4-pin connector Power one 24-pin connector Controls and Lights Front of computer: Power button push button Power light blue light — Blinking blue in sleep state; solid blue for power-on state amber light — The blinking amber indicates a problem with the system board. A solid amber light when the system does not boot indicates that the system board cannot start initialization.
Power Voltage (see the safety instructions located in the Product Information Guide for important voltage setting information) Coin cell battery 115/230 VAC, 50/60 Hz, 6A/3A 3-V CR2032 lithium coin cell Physical Height 36.2 cm (14.2 inches) Width 10.0 cm (3.9 inches) Depth 43.5 cm (17.1 inches) Weight 9.0 kg (19.
System Setup Overview Use system setup as follows: • To change the system configuration information after you add, change, or remove any hardware in your computer • To set or change a user-selectable option such as the user password • To read the current amount of memory or set the type of hard drive installed Before you use system setup, it is recommended that you write down the system setup screen information for future reference.
Options List — This field appears on the left side of the system setup window. The field is a scrollable list containing features that define the configuration of your computer, including installed hardware, power conservation, and security features. Option Field — This field contains information about each option. In this field you can view your current settings and make changes to your settings. Use the right and left arrow keys to highlight an option. Press to make that selection active.
System Setup Options NOTE: Depending on your computer and installed devices, the items listed in this section may not appear, or may not appear exactly as listed. System Info BIOS Info Shows the BIOS version number and date information System Info Lists system information such as the computer name, and other system-specific information. CPU Info Identifies whether the computer’s processor supports Hyper-Threading and lists the processor bus speed, processor ID, clock speed, and L2 cache.
Boot Up NumLock Status Off; On (On by default) Boot Device Configuration Removable Device Priority Used to set the device priority of removable devices like USB floppy drives. The items displayed are dynamically updated according to the removable devices connected. Hard Disk Boot Priority Used to set the device priority of hard drives. The items displayed are dynamically updated according to the hard drives detected.
Onboard LAN Boot ROM Enabled or Disabled (Disabled by default) SATA Mode IDE; RAID; AHCI (IDE by default) Power Management Setup ACPI Suspend Type S1(POS); S3(STR) (S3(STR) by default) Quick Resume Disabled; Enabled (Disabled by default) Remote Wake Up On; Off (On by default) USB KB Wake-Up From S3 Enabled; Disabled (Disabled by default) Auto Power On Enabled; Disabled (Disabled by default) Auto Power On Date 0 Auto Power On Time 0:00:00 AC Recovery Off; On; Former-Sts (Off by default) Boot
• USB Flash Device — Insert the memory device into a USB port and restart the computer. When F12 = Boot Menu appears in the upperright corner of the screen, press . The BIOS detects the device and adds the USB flash option to the boot menu. NOTE: To boot to a USB device, the device must be bootable. To make sure that your device is bootable, check the device documentation.
Changing Boot Sequence for Future Boots 1 Enter system setup (see "Entering System Setup" on page 170). 2 Use the arrow keys to highlight the Boot Sequence menu option and press to access the menu. NOTE: Write down your current boot sequence in case you want to restore it. 3 Press the up- and down-arrow keys to move through the list of devices. 4 Press the spacebar to enable or disable a device (enabled devices have a checkmark).
4 Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2. 5 Wait for approximately five seconds to clear the password. 6 Remove the 2-pin jumper plug from pins 1 and 2 and replace it on pins 2 and 3 to enable the password feature. 7 Replace the computer cover (see "Replacing the Computer Cover" on page 162). NOTICE: To connect a network cable, first plug the cable into the network device and then plug it into the computer.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer. 5 Connect your computer and devices to electrical outlets, and turn them on. Flashing the BIOS The BIOS may require flashing when an update is available or when replacing the system board. 1 Turn on the computer. 2 Locate the BIOS update file for your computer at the Dell Support website at support.dell.com. 3 Click Download Now to download the file.
Computer, Keyboard, and Monitor CAUTION: Before you clean your computer, disconnect the computer from the electrical outlet. Clean your computer with a soft cloth dampened with water. Do not use liquid or aerosol cleaners, which may contain flammable substances. • Use a vacuum cleaner with a brush attachment to gently remove dust from the slots and holes on your computer and from between the keys on the keyboard. NOTICE: Do not wipe the display screen with any soap or alcohol solution.
Floppy Drive NOTICE: Do not attempt to clean drive heads with a swab. You might accidentally misalign the heads, which prevents the drive from operating. Clean your floppy drive using a commercially available cleaning kit. These kits contain pretreated floppy disks to remove contaminants that accumulate during normal operation. CDs and DVDs NOTICE: Always use compressed air to clean the lens in the optical drive, and follow the instructions that come with the compressed air.
Dell provides limited technical support for the computer and any "Dellinstalled" software and peripherals1. Support for third-party software and peripherals is provided by the original manufacturer, including those purchased and/or installed through Dell Software and Peripherals, Readyware, and Custom Factory Integration2. 1 2 Repair services are provided pursuant to the terms and conditions of your limited warranty and any optional support service contract purchased with the computer.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. NOTICE: The FCC regulations provide that changes or modifications not expressly approved by Dell Inc. could void your authority to operate this equipment.
Contacting Dell For customers in the United States, call 800-WWW.DELL (800.999.3355). NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1 Visit support.
Appendix
Glossary Terms in this Glossary are provided for informational purposes only and may or may not describe features included with your particular computer. A AC — alternating current — The form of electricity that powers your computer when you plug the AC adapter power cable in to an electrical outlet.
understand what effect these settings have on the computer, do not change them. Also referred to as system setup. bit — The smallest unit of data interpreted by your computer. Blu-ray Disc™ (BD)— An optical storage technology offering storage capacity of up to 50 GB, full 1080p video resolution (HDTV required), and as many as 7.1 channels of native, uncompressed surround sound.
CD-RW — CD rewritable — A rewritable version of a CD. Data can be written to a CD-RW disc, and then erased and written over (rewritten). CD-RW drive — A drive that can read CDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times, but you can write to CD-R discs only once. CD-RW/DVD drive — A drive, sometimes referred to as a combo drive, that can read CDs and DVDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs.
DIMM — dual in-line memory module — A circuit board with memory chips that connects to a memory module on the system board. DIN connector — A round, six-pin connector that conforms to DIN (Deutsche Industrie-Norm) standards; it is typically used to connect PS/2 keyboard or mouse cable connectors. disk striping — A technique for spreading data over multiple disk drives. Disk striping can speed up operations that retrieve data from disk storage.
DVI — digital video interface — A standard for digital transmission between a computer and a digital video display. E ECC — error checking and correction — A type of memory that includes special circuitry for testing the accuracy of data as it passes in and out of memory. ECP — extended capabilities port — A parallel connector design that provides improved bidirectional data transmission. Similar to EPP, ECP uses direct memory access to transfer data and often improves performance.
F Fahrenheit — A temperature measurement scale where 32° is the freezing point and 212° is the boiling point of water. FBD — fully-buffered DIMM — A DIMM with DDR2 DRAM chips and an Advanced Memory Buffer (AMB) that speeds communication between the DDR2 SDRAM chips and the system. FCC — Federal Communications Commission — A U.S. agency responsible for enforcing communications-related regulations that state how much radiation computers and other electronic equipment can emit.
H hard drive — A drive that reads and writes data on a hard disk. The terms hard drive and hard disk are often used interchangeably. heat sink — A metal plate on some processors that helps dissipate heat. hibernate mode — A power management mode that saves everything in memory to a reserved space on the hard drive and then turns off the computer. When you restart the computer, the memory information that was saved to the hard drive is automatically restored.
IrDA — Infrared Data Association — The organization that creates international standards for infrared communications. IRQ — interrupt request — An electronic pathway assigned to a specific device so that the device can communicate with the processor. Each device connection must be assigned an IRQ. Although two devices can share the same IRQ assignment, you cannot operate both devices simultaneously.
M Mb — megabit — A measurement of memory chip capacity that equals 1024 Kb. Mbps — megabits per second — One million bits per second. This measurement is typically used for transmission speeds for networks and modems. MB — megabyte — A measurement of data storage that equals 1,048,576 bytes. 1 MB equals 1024 KB. When used to refer to hard drive storage, the term is often rounded to 1,000,000 bytes. MB/sec — megabytes per second — One million bytes per second.
MP — megapixel — A measure of image resolution used for digital cameras. ms — millisecond — A measure of time that equals one thousandth of a second. Access times of storage devices are often measured in ms. N network adapter — A chip that provides network capabilities. A computer may include a network adapter on its system board, or it may contain a PC Card with an adapter on it. A network adapter is also referred to as a NIC (network interface controller). NIC — See network adapter.
PCI Express — A modification to the PCI interface that boosts the data transfer rate between the processor and the devices attached to it. PCI Express can transfer data at speeds from 250 MB/sec to 4 GB/sec. If the PCI Express chip set and the device are capable of different speeds, they will operate at the slower speed. PCMCIA — Personal Computer Memory Card International Association — The organization that establishes standards for PC Cards.
read-only — Data and/or files you can view but cannot edit or delete. A file can have read-only status if: • It resides on a physically write-protected floppy disk, CD, or DVD. • It is located on a network in a directory and the system administrator has assigned rights only to specific individuals. refresh rate — The frequency, measured in Hz, at which your screen's horizontal lines are recharged (sometimes also referred to as its vertical frequency).
SDRAM — synchronous dynamic random-access memory — A type of DRAM that is synchronized with the optimal clock speed of the processor. serial connector — An I/O port often used to connect devices such as a handheld digital device or digital camera to your computer. Service Tag — A bar code label on your computer that identifies your computer when you access Dell Support at support.dell.com or when you call Dell for customer service or technical support.
The number of colors and resolution that a program displays depends on the capabilities of the monitor, the video controller and its drivers, and the amount of video memory installed in the computer. S-video TV-out — A connector used to attach a TV or digital audio device to the computer. SXGA — super-extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 1024.
UPS — uninterruptible power supply — A backup power source used when the electrical power fails or drops to an unacceptable voltage level. A UPS keeps a computer running for a limited amount of time when there is no electrical power. UPS systems typically provide surge suppression and may also provide voltage regulation. Small UPS systems provide battery power for a few minutes to enable you to shut down your computer.
turned on, the computer is infected when it reads the boot sectors of the floppy disk expecting to find the operating system. If the computer is infected, the boot virus may replicate itself onto all the floppy disks that are read or written in that computer until the virus is eradicated. V — volt — The measurement of electric potential or electromotive force. One V appears across a resistance of 1 ohm when a current of 1 ampere flows through that resistance.
Z ZIF — zero insertion force — A type of socket or connector that allows a computer chip to be installed or removed with no stress applied to either the chip or its socket. Zip — A popular data compression format. Files that have been compressed with the Zip format are called Zip files and usually have a filename extension of .zip. A special kind of zipped file is a self-extracting file, which has a filename extension of .exe. You can unzip a self-extracting file by double-clicking it.
Glossary
Index A audio.
D Dell contacting, 183 support policy, 180 support site, 13 Dell Diagnostics, 84 diagnostics beep codes, 80 Dell, 84 documentation End User License Agreement, 11 ergonomics, 11 Finding Information, 11 online, 13 Product Information Guide, 11 regulatory, 11 safety, 11 Setup Diagram, 11 warranty, 11 drive panel, 121 drive-panel insert removing, 135 replacing, 136 drivers, 87 about, 87 identifying, 88 reinstalling, 88 Drivers and Utilities media, 89 Dell Diagnostics, 84 drives, 124 hard drive, 126 installing f
floppy drive installing, 133 removing, 131 H hard drive installing, 128 installing second, 129 problems, 60 removing, 126 hardware beep codes, 80 conflicts, 97 Dell Diagnostics, 84 Hardware Troubleshooter, 97 Internet connection about, 53 options, 53 setting up, 54 IRQ conflicts, 97 K keyboard problems, 64 L labels Microsoft Windows, 12 Service Tag, 12, 16 hibernate mode, 34, 36, 38 I I/O panel replacing, 148 installing parts before you begin, 99 recommended tools, 99 turning off your computer, 100 In
modem problems, 60 monitor blank, 77 clone mode, 33 connect DVI, 31-32 connect TV, 31-32 connect two, 31-32 connect VGA, 31-32 display settings, 33 extended desktop mode, 33 hard to read, 78 motherboard.
problems (continued) CD-RW drive, 59 computer crashes, 65-66 computer stops responding, 65 conflicts, 97 Dell Diagnostics, 84 drives, 58 DVD drive, 59 e-mail, 60 error messages, 63 general, 65 hard drive, 60 Internet, 60 keyboard, 64 Media Card Reader, 68 memory, 69 modem, 60 monitor is blank, 77 monitor is hard to read, 78 mouse, 70 network, 71 optical drive, 59 power, 72 power light conditions, 72 printer, 73 program crashes, 65 program stops responding, 65 programs and Windows compatibility, 66 restore t
sound problems, 75 volume, 75 speaker problems, 75 volume, 75 specifications audio, 166 computer information, 165 connectors, 167 controls and lights, 168 drives, 167 environmental, 169 expansion bus, 166 memory, 165 physical, 169 power, 168 processor, 165 technical, 165 video, 165 standby mode, 33, 37 Starting the Dell Diagnostics From the Drivers and Utilities CD, 85 Starting the Dell Diagnostics From Your Hard Drive, 84 support contacting Dell, 183 policy, 180 support website, 13 system board, 105 208
V volume adjusting, 76 W warranty information, 11 Windows Files and Settings Transfer Wizard, 47 Network Setup Wizard, 52 Windows XP Device Driver Rollback, 89 hibernate mode, 34 PC Restore, 93 standby mode, 33 wizards Files and Settings Transfer Wizard, 47 Network Setup Wizard, 52 Program Compatibility Wizard, 66 Windows Vista Device Driver Rollback, 88-89 Factory Image Restore, 93 Program Compatibility Wizard, 66 reinstalling, 92 scanner, 75 System Restore, 92 Index 209
Index
