Dell Interactive Projector S520 Screen/Whiteboard PTDRV
Important Safety Instructions WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
Product Dimensions 14.02 in. (356.2 mm) 5.02 in. (127.4 mm) Front View Side View 4.99 in. (126.7 mm) 78.75 in. (2000.1 mm) 80.37 in. (2041.4 mm) 41.60 in. (1056.5 mm) 38.77 in. (984.8 mm) 15.23 in. (386.8 mm) 6.6 in. (167.52 mm) 1.21 in. (30.65 mm) 55.52 in. (1410.1 mm) Back View 1.67 in. (42.3 mm) 2.4 in. (60.9 mm) Top View 28.07 in. (712.
Tools Required for Installation 1/8 in. (wood) 1/2 in.
Installation 4. Determine location of studs behind drywall. 1. Determine desired height of image (measured from floor) (Figure 1). 5. Drill one pilot hole into a wall stud at location marked in Step 3 (Figure 1). 2. Determine desired center of image area (Figure 1). 3. Measure 4-1/16” up from desired height (top) of image and 4” to the right of center of screen and mark location (Figure 1). 4 in. 4-1/16 in. Center of Screen 46-1/8 in. Height from Floor 73-3/4 in.
Installation (continued) Center of Screen NOTE: The (3) 1/4” x 1-1/2” bolts and (3) washers required in Steps 6-8 are NOT INCLUDED with the screen/whiteboard packaging. 6. Install (1) 1/4” x 1-1/2” bolt and (1) washer through middle of bracket into previously drilled hole, leaving 1/2” of the bolt extending from wall. Use carpenter’s level to make sure bracket is properly level (Figure 2). 7. Position level on top of wall bracket. Move bracket until level.
10. Install the (3) screen brackets using: Wood or steel studs: (3) supplied #8 x 1” screws. Concrete wall or no studs: (3) supplied #8-10 wall anchors and (3) supplied #8 x 1” screws. 11. Install projector mount. Refer to the S520 Dual Stud Wall Mount (MSP-DCCUST2) manual. Do not install the (2) plastic covers for mount (Figure 4). 12. Run cables for projector up through hole in wall bracket and cover to projector location (Figure 5).
Installation (continued) 13. Mount screen onto wall bracket by hooking into the back groove of the screen frame (Figure 6). NOTE: The bumpers on the back side of the screen/whiteboard are used to maintain planarity when pressure is applied to the projection surface during usage. If the bumpers are obstructing installation on your wall during Steps 13 and 14, they can be removed. 14.
17. Secure marker tray to right side of screen frame at desired height by using (2) of the supplied #8 x 1/2” screws into the side channel of the screen frame (Figure 9). Attach marker tray to frame with (2) screws into the side channel. 18. Secure marker tray (Figure 10) to wall using: Wood or steel studs: (1) supplied #8 x 1” screw. Concrete wall or no studs: (1) supplied #8-10 wall anchor and (1) #8 x 1” screw. 19.
Installation (continued) DC Power Cable for Sensor 20. Attach sensor cover by snapping clips over screen frame. Secure to frame by screwing down into the upper channel of the screen frame with supplied #8 x 3/4” screw (Figure 12). 21. In between the projector mount and the IR sensor cover, cable clips will be mounted to the wall for cable management. Attach clips to the wall using: Wood studs: (4) supplied #8 x 1” screws.
Recommended Screen/Whiteboard Markers Recommended Screen/Whiteboard Cleaning This Dell S520 Screen/Whiteboard is a dual-purpose projection screen and whiteboard. The surface of the screen/whiteboard can be used with dry erase markers from a wide variety of manufacturers and brands. Do not use permanent markers with this product. The supplied cleaning cloth can be used to clean marks on the Dell S520 Screen/Whiteboard surface made by everyday dry erase marker usage.
Installation Video For further guidance and helpful information about installing an S520 Dual Stud Wall Mount and S520 Screen/Whiteboard, please reference the installation video: http://downloads.chiefmfg.com/MANUALS-I/Dell Interactive Solution.mp4 • • • • • • Go to http://downloads.chiefmfg.com/MANUALSI/PTDRV-I.pdf for translated instructions. Entre en http://downloads.chiefmfg.com/ MANUALS-I/PTDRV-I.pdf para obtener las instrucciones traducidas en su idioma.