Users Guide

ManualsBrandsDell ManualsAccess PlatformsPowerSwitch S3048-ON

Dell Command Line Reference Guide for the S3048–

ON System

9.9(0.0)

Summary of content (1633 pages)

PAGE 1
Dell Command Line Reference Guide for the S3048– ON System 9.9(0.
PAGE 2
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
PAGE 3
Contents 1 About this Guide............................................................................................................ 40 Objectives........................................................................................................................................................................ 40 Audience..........................................................................................................................................................................
PAGE 4
Control and Monitoring................................................................................................. 84 banner exec......................................................................................................................................................................84 banner login......................................................................................................................................................................85 banner motd...............
PAGE 5
show environment.......................................................................................................................................................... 129 show inventory............................................................................................................................................................... 130 show login statistics..........................................................................................................................................
PAGE 6
debug dot1x.................................................................................................................................................................... 175 dot1x auth-fail-vlan..........................................................................................................................................................176 dot1x auth-server.........................................................................................................................................
PAGE 7
permit udp................................................................................................................................................................224 resequence access-list............................................................................................................................................. 227 seq.......................................................................................................................................................................
PAGE 8
set metric................................................................................................................................................................. 270 set metric-type......................................................................................................................................................... 271 set next-hop.......................................................................................................................................................
PAGE 9
8 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM)... 322 member vlan.................................................................................................................................................................. 322 ip access-group..............................................................................................................................................................323 show acl-vlan-group .....................................................
PAGE 10
bgp dampening........................................................................................................................................................ 360 bgp default local-preference..................................................................................................................................... 361 bgp dmzlink-bw........................................................................................................................................................
PAGE 11
neighbor route-reflector-client................................................................................................................................. 404 neighbor sender-side-loopdetect............................................................................................................................. 405 neighbor send-community....................................................................................................................................... 406 neighbor shutdown......
PAGE 12
IPv6 BGP Commands..................................................................................................................................................... 461 clear ip bgp ipv6 unicast soft.................................................................................................................................... 461 debug ip bgp ipv6 unicast soft-reconfiguration........................................................................................................ 462 ipv6 prefix-list...
PAGE 13
show hardware stack-unit buffer-stats-snapshot (Total Buffer Information)............................................................504 show hardware system-flow.................................................................................................................................... 506 show hardware vlan-counters.................................................................................................................................. 508 show hardware drops................................
PAGE 14
ipv6 dhcp snooping verify mac-address................................................................................................................... 538 ip helper-address......................................................................................................................................................538 ipv6 helper-address..................................................................................................................................................
PAGE 15
garp timers..................................................................................................................................................................... 578 gvrp enable.................................................................................................................................................................... 580 gvrp registration......................................................................................................................................
PAGE 16
ip igmp snooping last-member-query-interval.......................................................................................................... 620 ip igmp snooping mrouter..........................................................................................................................................621 ip igmp snooping querier..........................................................................................................................................
PAGE 17
switchport................................................................................................................................................................685 Egress Interface Selection (EIS) Commands..................................................................................................................686 application................................................................................................................................................................
PAGE 18
clear ip fib stack-unit...................................................................................................................................................... 723 clear ip route...................................................................................................................................................................724 clear tcp statistics.....................................................................................................................................
PAGE 19
show cam-acl.................................................................................................................................................................785 permit icmp.................................................................................................................................................................... 787 permit.....................................................................................................................................................
PAGE 20
debug isis update-packets..............................................................................................................................................828 default-information originate.......................................................................................................................................... 829 description..............................................................................................................................................................
PAGE 21
set-overload-bit............................................................................................................................................................. 869 show config....................................................................................................................................................................870 show isis database.........................................................................................................................................
PAGE 22
Far-End Failure Detection (FEFD)...................................................................................................................................918 debug fefd................................................................................................................................................................ 918 fefd......................................................................................................................................................................
PAGE 23
32 Multicast Source Discovery Protocol (MSDP).......................................................... 954 clear ip msdp peer..........................................................................................................................................................954 clear ip msdp sa-cache.................................................................................................................................................. 955 clear ip msdp statistic................................
PAGE 24
35 Neighbor Discovery Protocol (NDP)......................................................................... 994 clear ipv6 neighbors....................................................................................................................................................... 994 ipv6 neighbor................................................................................................................................................................. 995 show ipv6 neighbors........................
PAGE 25
OSPFv2 Commands..................................................................................................................................................... 1028 area default-cost.................................................................................................................................................... 1028 area nssa................................................................................................................................................................
PAGE 26
show ip ospf database asbr-summary.....................................................................................................................1072 show ip ospf database external............................................................................................................................... 1074 show ip ospf database network..............................................................................................................................
PAGE 27
show ipv6 ospf database......................................................................................................................................... 1128 show ipv6 ospf interface......................................................................................................................................... 1130 show ipv6 ospf neighbor.......................................................................................................................................... 1131 timers spf..
PAGE 28
40 Port Monitoring........................................................................................................ 1173 description.....................................................................................................................................................................1173 monitor multicast-queue................................................................................................................................................ 1174 monitor session...............
PAGE 29
match ip access-group............................................................................................................................................ 1215 match ip dscp..........................................................................................................................................................1216 match ip precedence...............................................................................................................................................
PAGE 30
debug ip rip...................................................................................................................................................................1258 default-information originate.........................................................................................................................................1259 default-metric...................................................................................................................................................
PAGE 31
forward-delay............................................................................................................................................................... 1303 hello-time......................................................................................................................................................................1304 max-age..................................................................................................................................................
PAGE 32
radius-server group.................................................................................................................................................1344 radius-server host...................................................................................................................................................1345 radius-server vrf.....................................................................................................................................................
PAGE 33
ip ssh server vrf......................................................................................................................................................1383 ip ssh source-interface........................................................................................................................................... 1384 ip ssh vrf.................................................................................................................................................................
PAGE 34
51 Simple Network Management Protocol (SNMP) and Syslog.................................... 1424 SNMP Commands........................................................................................................................................................ 1424 show snmp............................................................................................................................................................. 1424 show snmp engineID......................................................
PAGE 35
52 SNMP Traps............................................................................................................ 1468 53 Stacking...................................................................................................................1475 redundancy disable-auto-reboot................................................................................................................................... 1475 redundancy force-failover stack-unit...................................................
PAGE 36
SupportAssist Commands.............................................................................................................................................. 1511 activity..................................................................................................................................................................... 1511 contact-company....................................................................................................................................................
PAGE 37
show ntp status............................................................................................................................................................1540 58 Tunneling ................................................................................................................ 1542 ip unnumbered..............................................................................................................................................................1542 ipv6 unnumbered.............
PAGE 38
ipv6 route-import.......................................................................................................................................................... 1577 match source-protocol..................................................................................................................................................1578 redistribute.......................................................................................................................................................
PAGE 39
authentication-type................................................................................................................................................. 1612 clear counters vrrp.................................................................................................................................................. 1613 debug vrrp...............................................................................................................................................................
PAGE 40
1 About this Guide This guide provides information about the Dell Networking operating system command line interface (CLI). This book also includes information about the protocols and features supported in Dell Networking OS.
PAGE 41
Information Icons This book uses the following information symbols: NOTE: The Note icon signals important operational information. CAUTION: The Caution icon signals information about situations that could result in equipment damage or loss of data. WARNING: The Warning icon signals information about hardware handling that could result in injury.
PAGE 42
2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols. Accessing the Command Line When the system boots successfully, you are positioned on the command line in EXEC mode and not prompted to log in. You can access the commands through a serial console port or a Telnet session.
PAGE 43
In this case, the user is “admin” on vty2. Obtaining Help As soon as you are in a command mode there are several ways to access help. To obtain a list of keywords at any command mode: Type a ? at the prompt or after a keyword. There must always be a space before the ?. To obtain a list of keywords with a brief functional description: Type help at the prompt. To obtain a list of available options: Type a keyword and then type a space and a ?.
PAGE 44
• To navigate left or right in the Dell Networking OS command line, use the left and right Arrow keys. The shortcut key combinations at the Dell Networking OS command line are as follows: Key Combination Action CNTL-A Moves the cursor to the beginning of the command line. CNTL-B Moves the cursor back one character. CNTL-D Deletes the character at the cursor. CNTL-E Moves the cursor to the end of the line. CNTL-F Moves the cursor forward one character. CNTL-I Completes a keyword.
PAGE 45
Filtering show Commands To find specific information, display certain information only or begin the command output at the first instance of a regular expression or phrase, you can filter the display output of a show command. When you execute a show command, and then enter a pipe ( | ), one of the following parameters, and a regular expression, the resulting output either excludes or includes those parameters.
PAGE 46
NOTE: The no feature vrf command is not supported on any of the platforms. To enable the VRF feature and cause all VRF-related commands to be available or viewable in the CLI interface, use the following command. You must enable the VRF feature before you can configure its related attributes. Dell(conf)# feature vrf Based on whether VRF feature is identified as supported in the Feature Configuration file, configuration command feature vrf becomes available for usage.
PAGE 47
Command History Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.4(0.0) Introduced on the S4810, S4820T, and S6000. Usage Information You can activate VRF application on a device by using the feature vrf command in CONFIGURATION mode. The no feature vrf command is not supported on any of the platforms.
PAGE 48
CONTROL-PLANE Mode To manage control-plane traffic, use CONTROL-PLANE mode. For more information, refer to Control Plane Policing (CoPP). To enter CONTROL-PLANE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the control-plane-cpuqos command. The prompt changes to include (conf-control-cpuqos). You can return to CONFIGURATION mode by using the exit command. DHCP Mode To enable and configure Dynamic Host Configuration Protocol (DHCP), use DHCP mode.
PAGE 49
EXEC Mode When you initially log in to the switch, by default, you are logged in to EXEC mode. This mode allows you to view settings and enter EXEC Privilege mode, which is used to configure the device. When you are in EXEC mode, the > prompt is displayed following the host name prompt, which is “Dell” by default. You can change the host name prompt using the hostname command. NOTE: Each mode prompt is preceded by the host name. EXEC Privilege Mode The enable command accesses EXEC Privilege mode.
PAGE 50
Prompt Interface Type Dell(conf-if)# INTERFACE mode Dell(conf-ifgi-1/1)# Gigabit Ethernet interface then the slot/port information Dell(conf-ifte-1/1)# Ten-Gigabit Ethernet interface then slot/port information Dell(conf-iflo-0)# Loopback interface number Dell(conf-ifnu-0)# Null Interface then zero Dell(conf-ifpo-0)# Port-channel interface number Dell(conf-ifvl-0)# VLAN Interface then VLAN number (range 1–4094) Dell(conf-ifma-1/1)# Management Ethernet interface then slot/port information De
PAGE 51
2. Enter the protocol lldp command. The prompt changes to include (conf-lldp) or (conf-if-interface-lldp). LLDP MANAGEMENT INTERFACE Mode To enable and configure Link Layer Discovery Protocol (LLDP) on management interfaces, use LLDP MANAGEMENT INTERFACE mode. To enter LLDP MANAGEMENT INTERFACE mode: 1. Verify that you are logged in to LLDP mode. 2. Enter the management-interface command. The prompt changes to include (conf-lldp-mgmtIf).
PAGE 52
To enter OPENFLOW INSTANCE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the openflow of-instance command then the OpenFlow ID number of the instance you want to create or configure. The prompt changes to include (conf-of-instance of-id). You can return to the CONFIGURATION mode by entering the exit command. Per-VLAN SPANNING TREE (PVST+) Plus Mode To enable and configure the Per-VLAN Spanning Tree (PVST+) protocol, use PVST+ mode.
PAGE 53
1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree rstp command. The prompt changes to include (conf-rstp). You can return to CONFIGURATION mode by using the exit command. ROUTE-MAP Mode To configure a route map, use ROUTE-MAP mode. To enter ROUTE-MAP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Use the route-map map-name [permit | deny] [sequence-number] command. The prompt changes to include (config-route-map).
PAGE 54
2. Enter the ipv6 router ospf {process-id} command. The prompt changes to include (conf-ipv6-router_ospf). You can return to CONFIGURATION mode by using the exit command. ROUTER RIP Mode To enable and configure Router Information Protocol (RIP), use ROUTER RIP mode. For more information, refer to Routing Information Protocol (RIP). To enter ROUTER RIP mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the router rip command. The prompt changes to include (conf-router_rip).
PAGE 55
VRRP Mode To enable and configure Virtual Router Redundancy Protocol (VRRP), use VRRP mode. For more information, refer to Virtual Router Redundancy Protocol (VRRP). To enter VRRP mode: 1. To enable VRRP globally, verify that you are logged in to CONFIGURATION mode. 2. Enter the vrrp-group command then enter the VRRP group ID. The prompt changes to include (conf-if-interface-type-slot/ port-vrid-vrrp-group-id).
PAGE 56
3 File Management This chapter contains command line interface (CLI) commands needed to manage the configuration files as well as other file management commands. boot system Specify the location where the Dell Networking OS image used to boot the system is stored. Syntax boot system {gateway ip address | stack-unit [{stack-unit-number | all] [default | primary {system: {A: | B: | bmp-boot} | tftp: | secondary]} To return to the default boot sequence, use the no boot system command.
PAGE 57
NOTE: In normal-reload, this keyword is not enabled. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 58
Version Description 9.7(0.0) Added NFS mount support. Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. copy Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, HTTP, TFTP, and SCP (in the hostip field).
PAGE 59
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added the nfsmount: parameters that allow you to mount a remote NFS file system. 9.4(0.0) Added the compressed-config parameter. 9.3(0.1) Added the http parameter on the S6000, Z9000, S4810, and S4820T. 9.0.2.0 Introduced on the S6000. 8.4.1.0 Added IPv6 addressing support for FTP, TFTP, and SCP. 8.3.19.
PAGE 60
In this copy scp: flash: example, specifying SCP in the first position indicates that you need to specify the target in the ensuing prompts. Entering flash: in the second position indicates that the target is the internal flash. The source is on a secure server running secure shell (SSH), so you are prompted for the user datagram protocol (UDP) port of the SSH server on the remote host. Example Dell#copy running-config nfsmount:///filepath Destination file name [test.
PAGE 61
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for NFS mount. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 62
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Added support for NFS mount. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 63
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series You must include the colon (:) when entering this command.
PAGE 64
Usage Information Version Description 8.3.19.0 Introduced on S4820T. Include the colon (:) when entering this command. This command checks the specified flash memory for errors. If errors are found, the command recommends that you format the flash. CAUTION: If you elect to format the flash, all files – including the startup configuration file – are lost.
PAGE 65
username (OPTIONAL) Enter the user name to access the device. password (OPTIONAL) Enter the password. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 66
upgrade system Upgrade the Dell Networking OS image. To upgrade the bootflash or bootselector image, use the upgrade boot command. Syntax upgrade system {flash: | ftp: | nfsmount: | scp: | stack-unit {stack-unitid | all} | tftp: | usbflash:} file-url {A: |B:} Parameters system Enter the keyword system to upgrade the operating system (OS) image. flash: file-url Enter the keyword flash: and specify the location of the image file in the format //directory-path or press Enter to launch a prompt sequence.
PAGE 67
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added support for TFTP and SCP. 7.6.1.0 Introduced on the S-Series. RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) must be enclosed in square brackets, [X:X:X:X::X]. For maximum flexibility this command accepts IPv6 host addresses with or without the square brackets. After you upgrade the system image, by entering the command.
PAGE 68
Destination file name [sample_file]: Defaults None. Command Modes EXEC Privilege Command History Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.1) Introduced on the S6000, Z9000, S4810, and S4820T. copy http://admin:admin123@10.16.206.77/sample_file flash://sample_file rename Rename a file in the local file system.
PAGE 69
Version Description E-Series Original command restore factory-defaults Restore factory defaults. Syntax Parameters restore factory-defaults stack-unit {stack—unit—number | all} {clear-all | bootvar | nvram} factory-defaults Return the system to its factory default mode. stack-unit-number Enter the stack member unit identifier to restore only the mentioned stack-unit. The range is from 1 to 6. all Enter the keyword all to restore all units in the stack.
PAGE 70
When restoring a single unit in a stack, that unit placed in stand-alone mode. No other units in the stack are affected. When restoring units in stand-alone mode, the units remain in stand-alone mode after the restoration. After the restore is complete, the units power cycle immediately. CAUTION: There is no undo for this command.
PAGE 71
************************************************************** Proceed with factory settings? Confirm [yes/no]:yes -- Restore status -Unit Nvram Config -----------------------0 Success Success Power-cycling the unit(s). Dell# Example (NvRAM all Dell#restore factory-defaults stack-unit all nvram ************************************************************** stack units) * Warning - Restoring factory defaults will delete the existing * * persistent settings (stacking, fanout, etc.
PAGE 72
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 73
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 Output expanded to display current reload mode (normal or Jumpstart). 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Dell#show bootvar PRIMARY IMAGE FILE = system://B SECONDARY IMAGE FILE = tftp://10.16.127.35/Dell-SI-9-0-2-0.
PAGE 74
Example Version Description 7.6.1.0 Introduced on the S-Series 7.5.1.0 Introduced on the C-Series E-Series Original command Dell#show file-systems Size(b) Free(b) Feature Type Flags Prefixes 63938560 51646464 dosFs2.0 MMC rw flash: 63938560 18092032 dosFs1.0 MMC rw slot0: - - - network rw ftp: - - - network rw tftp: - - - network rw scp: Dell# Command Fields Field Description size(b) Lists the size (in bytes) of the storage location. If the location is remote, no size is listed.
PAGE 75
Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 76
File Management cam-profile for the current CAM profile in the configuration class-map for the current class-map configuration communitylist for the current community-list configuration ecmp-group for the current ECMP group configuration eis for the current EIS configuration ethernet for the current Ethernet CFM configuration fefd for the current FEFD configuration ftp for the current FTP configuration frrp for the current FRRP configuration fvrp for the current FVRP configuration g
PAGE 77
ntp for the current NTP configuration ospf for the current OSPF configuration pim for the current PIM configuration policy-mapinput for the current input policy map configuration policy-mapoutput for the current output policy map configuration po-failovergroup for the current port-channel failover-group configuration prefix-list for the current prefix-list configuration privilege for the current privilege configuration qos-policyinput for the current input QoS policy configuration qos-poli
PAGE 78
configured (OPTIONAL) Enter the keyword configuration to display line card interfaces with non-default configurations only. status (OPTIONAL) Enter the keyword status to display the checksum for the running configuration and the start-up configuration. compressed (Optional) Enter the keyword compressed to display the compressed group configuration. Displays the compressed configuration by grouping all similar configurations. The compression is done only for interface related configurations.
PAGE 79
redundancy disable-auto-reboot redundancy disable-auto-reboot redundancy disable-auto-reboot redundancy disable-auto-reboot redundancy disable-auto-reboot ! hardware watchdog stack-unit 1 hardware watchdog stack-unit 2 hardware watchdog stack-unit 3 stack-unit stack-unit stack-unit stack-unit stack-unit 2 3 4 5 6 Example Dell#show running-config status running-config bytes 10257, checksum 0xFD33339F startup-config bytes 10257, checksum 0xFD33339F Usage Information The status option allows you to displ
PAGE 80
boot system stack-unit 0 default system: A: boot system gateway 10.16.132.254 ! redundancy auto-synchronize full redundancy disable-auto-reboot stack-unit ... Related Commands show running-config – displays the current (running) configuration. show version Display the current Dell Networking Operating System (OS) version information on the system. Syntax show version Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 81
Example (S-Series) Lines Beginning With Description System image... Image file name System Type: S4810, S4820T, Z9000, S6000 Control Processor:... Control processor information and amount of memory on processor 128K bytes... Amount and type of memory on system 1 Route Processor... Hardware configuration of the system, including the number and type of physical interfaces available Dell#show version Dell Real Time Operating System Software Dell Operating System Version: 1.
PAGE 82
upgrade Upgrade the bootflash image or system image of the management unit. Syntax upgrade {boot | system} {ftp: | scp: | tftp: | flash: {A: |B:} | stack-unit | usbflash | slot0:} file-url Parameters boot Enter the keyword boot to change the boot image. system Enter the keyword system to change the system image.
PAGE 83
Usage Information Version 9.0(0.0) Added support for IPv6 for the file-url parameter. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Added support for the SSD on the Z9000 only. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Added support for TFTP and SCP. Version 7.6.1.0 Introduced on the S-Series. RFC 3986 specifies that IPv6 host addresses in a uniform resource identifier (URI) must be enclosed in square brackets, [X:X:X:X::X].
PAGE 84
4 Control and Monitoring This chapter contains the commands to configure and monitor the system, including Telnet, file transfer protocol (FTP), and trivial file transfer protocol (TFTP). NOTE: This command replaces the enable optic-info-update interval command to update information on temperature and power monitoring in the simple network management protocol (SNMP) management information base (MIB). banner exec Configure a message that is displayed when your enter EXEC mode.
PAGE 85
Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original Command Usage Information After entering the banner login command, type one or more spaces and a delineator character. Enter the banner text then the second delineator character. When the user is connected to the router, if a message of the day banner is configured, it displays first.
PAGE 86
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 87
Related Commands banner motd — sets a Message of the Day banner. banner exec — enables the display of a text string when you enter EXEC mode. banner motd Set a message of the day (MOTD) banner. Syntax banner motd c line c To delete a Message of the Day banner, enter no banner motd. Parameters c Enter a delineator character to specify the limits of the text banner. The delineator is a percent character (%). line Enter a text string for your MOTD banner the message with your delineator.
PAGE 88
Related Commands banner exec — enables the display of a text string when you enter EXEC mode. banner login — sets a banner to display after successful login to the system. cam-acl Allocate content addressable memory (CAM) for IPv4 and IPv6 ACLs.
PAGE 89
Usage Information Version Description 9.2(0.2) Added support for the fcoe parameter on the S4810 and S4820T. 9.1.(0.0) Added support for OpenFlow on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added the keywords fcoeacl and iscsioptacl on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Added the keywords ecfmacl, vman-qos, and vman-dual-qos. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 90
Usage Information Version Description 9.1.(0.0) Introduced on S4810. 8.3.19.0 Introduced on the S4820T. Reboot the switch after changing the parameter values for changes to take effect. For platform-specific instructions about using this command, refer to the SDN chapter in the Dell Networking OS Configuration Guide. clear line Reset a terminal line. Syntax clear line {line-number | console 0 | vty number} Parameters line-number Enter a number for one of the 12 terminal lines on the system.
PAGE 91
configure Enter CONFIGURATION mode from EXEC Privilege mode. Syntax Parameters configure [terminal] terminal (OPTIONAL) Enter the keyword terminal to specify that you are configuring from the terminal. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 92
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 93
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 94
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 95
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Replacement command for the S4820T. Replaces the enable xfp-powerupdates command. 8.3.11.4 Replacement command for the Z9000. Replaces the enable xfp-powerupdates command 8.3.10.0 Replacement command for the S4810 only. Replaces the enable xfp-powerupdates command. To enable polling and to configure the polling frequency, use this command.
PAGE 96
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series. E-Series Original command. exit — returns to the lower command mode.
PAGE 97
Version Description 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information To remove the time interval, enter exec-timeout 0 0. Example Dell con0 is now available Press RETURN to get started. Dell> exit Return to the lower command mode.
PAGE 98
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. end — returns to EXEC Privilege mode. ftp-server enable Enable FTP server functions on the system.
PAGE 99
Name (10.31.1.111:dch): dch 331 Password required Password: 230 User logged in ftp> pwd 257 Current directory is "flash:" ftp> dir 200 Port set okay 150 Opening ASCII mode data connection size date time name -------- ------ ------ -------512 Jul-20-2004 18:15:00 tgtimg 512 Jul-20-2004 18:15:00 diagnostic 512 Jul-20-2004 18:15:00 other 512 Jul-20-2004 18:15:00 tgt 226 Transfer complete 329 bytes received in 0.018 seconds (17.
PAGE 100
Version Description E-Series Original command. Usage Information After you enable FTP server functions with the ftp-server enable command, Dell Networking recommends specifying a top-level directory path. Without a top-level directory path specified, the Dell Networking OS directs users to the flash directory when logging in to the FTP server. Related Commands ftp-server enable — enables FTP server functions on the E-Series.
PAGE 101
Version Description 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. hostname Set the host name of the system. Syntax Parameters hostname name name Enter a text string, up to 32 characters long. Defaults Dell Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 102
ip http source-interface Specify an interface as the source interface for HTTP connections. This feature is supported on platform. Syntax ip http source-interface interface To delete an interface, use theno ip http source-interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 103
ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
PAGE 104
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 105
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. • For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 106
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command.
PAGE 107
Usage Information Use this command to make the FTP clients VRF-aware. The VRF name that you specify is used by the FTP client to reach the FTP server. If no VRF name is specified, then the default VRF is used. ip telnet server enable Enable the Telnet server on the switch. Syntax ip telnet server enable To disable the Telnet server, use the no ip telnet server enable command. Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 108
Parameters vrf management Enter the keyword vrf followed by the keyword management to specify a management VRF that is used by the TELNET server. vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is used by the TELNET server. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 109
• For a tunnel interface, enter the keyword tunnel. Defaults The IP address on the system that is closest to the Telnet address is used in the outgoing packets. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.
PAGE 110
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000.
PAGE 111
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4820T. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.0 Increased number of VLANs on ExaScale to 4094 (was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 112
Related Commands ftp-server topdir — sets the directory to be used for incoming FTP connections. ftp-server username — sets a username and password for incoming FTP connections. line Enable and configure console and virtual terminal lines to the system. This command accesses LINE mode, where you can set the access conditions for the designated line. Syntax line {aux 0 |console 0 | vty number [end-number]} Parameters aux 0 Enter the keyword aux 0 to configure the auxiliary terminal connection.
PAGE 113
Related Commands access-class — restricts the incoming connections to a particular IP address in an IP access control list (ACL). password — specifies a password for users on terminal lines. login concurrent-session Configures the limit of concurrent sessions for all users on console and virtual terminal lines.
PAGE 114
The following example shows how to use the login concurrent-session clear-line enable command. Dell(conf)#login concurrent-session clear-line enable Dell(conf)# When you try to log in, the following message appears with all your existing concurrent sessions, providing an option to close any one of the existing sessions: $ telnet 10.11.178.14 Trying 10.11.178.14... Connected to 10.11.178.14. Escape character is '^]'. Login: admin Password: Current sessions for user admin: Line Location 2 vty 0 10.14.1.
PAGE 115
time-period days Sets the number of days for which the system stores the user login statistics. The range is from 1 to 30. Defaults Not configured Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 116
The preceding message shows that the user had previously logged in to the system using the console line. It also displays the number of unsuccessful login attempts since the last login and the number of unsuccessful login attempts during a custom time period. Related Commands login concurrent-session — Configures the limit of concurrent sessions for all users on console and virtual terminal lines.
PAGE 117
ping Test connectivity between the system and another device by sending echo requests and waiting for replies.
PAGE 118
• Y: Do validate reply data. Default is No. Defaults outgoing-interface (IPv6 link-local address) Enter the outgoing interface for ping packets to a destination link-local address. pattern pattern (IPv4 only) Enter the IPv4 data pattern. Range: 0-FFFF. Default: 0xABCD. sweep-min-size Enter the minimum size of datagram in sweep range. The range is from 52 to 15359 bytes. sweep-max-size Enter the maximum size of datagram in sweep range. The range is from 53 to 15359 bytes.
PAGE 119
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards on the ExaScale. 8.4.1.0 IPv6 pinging available on management interface. 8.3.1.0 Introduced extended ping options. 8.2.1.0 Introduced on the E-Series ExaScale (IPv6). 8.1.1.0 Introduced on the E-Series ExaScale (IPv4). 7.9.1.0 Introduced VRF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for IPv6 address on the E-Series.
PAGE 120
reload Reboot Dell Networking Operating System (OS). Syntax reload [conditional nvram-cfg-change] Parameters conditional nvramcfg-change Reload if the condition is true. A configuration change to the nvram requires a switch reload. To reload the switch, select nvram-cfg-change. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 121
vty Enter the keyword vty to send a message to the virtual terminal. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 122
localtime (OPTIONAL) Enter the keyword localtime to include the localtime in the timestamp. msec (OPTIONAL) Enter the keyword msec to include milliseconds in the timestamp. show-timezone (OPTIONAL) Enter the keyword show-timezone to include the time zone information in the timestamp. uptime (OPTIONAL) Enter the keyword uptime to have the timestamp based on time elapsed since system reboot. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 123
Parameters Command Modes Command History threshold • EXEC • EXEC Privilege (OPTIONAL) Enter the keyword threshold to display the temperature thresholds in Celcuis for each level. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 124
show cam-acl-vlan Display the block sizes allocated for the VLAN CAM ACL. Syntax show cam-acl-vlan Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. Version 9.1.(0.
PAGE 125
Usage Information One trace log message is generated for each command. No password information is saved to this file. A command-history trace log is saved to a file after failover. Dell Networking TAC analyzes this file to help identify the root cause of it. Example Dell#show command-history [11/20 15:47:22]: CMD-(CLI):[service password-encryption]by default from console [11/20 15:47:22]: CMD-(CLI):[service password-encryption hostname Force10]by default from console - Repeated 3 times.
PAGE 126
no Defaults Display all of the commands that may be preceded by the keyword no, which is the keyword used to remove a command from the running-configuration. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 127
show cpu-traffic-stats View the CPU traffic statistics. Syntax Parameters show cpu-traffic-stats [port number | all | cp ] port number (OPTIONAL) Enter the port number to display traffic statistics on that port only. The range is from 1 to 1568. all (OPTIONAL) Enter the keyword all to display traffic statistics on all the interfaces receiving traffic, sorted based on the traffic. cp (OPTIONAL) Enter the keyword cp to display traffic statistics on the specified CPU.
PAGE 128
Processor : RP1 --------------Received 62% traffic on GigabitEthernet 8/2 Total packets:500 LLC:0, SNAP:0, IP:500, ARP:0, other:0 Unicast:500, Multicast:0, Broadcast:0 Received 37% traffic on GigabitEthernet 8/1 Total packets:300 LLC:0, SNAP:0, IP:300, ARP:0, other:0 Unicast:300, Multicast:0, Broadcast:0 Processor : RP2 --------------No CPU traffic statistics. Dell# show debugging View a list of all enabled debugging processes.
PAGE 129
GigabitEthernet 5/1,5/2,5/4,5/6,5/8,5/10,5/12,5/14,5/16 Dell# show environment View S-Series and Z-Series system component status (for example, temperature or voltage). Syntax Parameters Command Modes Command History show environment [all | fan | stack-unit unit-id | pem | thermal-sensor ] all Enter the keyword all to view all components. fan Enter the keyword fan to view information on the fans. The output of this command is chassis dependent.
PAGE 130
0 0 0 0 1 2 up up up up up up 6971 6971 7021 up up up 7072 7021 7021 Speed in RPM -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) ---------------------------------------------0 0 down UNKNOWN down 0 0 1 up AC up 6504 -- Unit Environment Status -Unit Status Temp Voltage TempStatus ---------------------------------* 0 online 36C ok 1 * Management Unit -- Thermal Sensor Readings (deg C) -Unit Sensor0 Sensor1 Sensor2 Sensor3 Sensor4 Sensor5 Sensor6 ----------------------------------------
PAGE 131
NOTE: This parameter is available but not supported in Dell Networking Operating System version 8.3.11.4. Because stacking is not supported, if you use this parameter, the output displays “Media not present or accessible” (refer to the Usage Information section). Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 132
-------------------------LLDP Example Dell#show inventory media Slot Port Type Media Serial Number F10Qualified --------------------------------------------------------0 0 QSFP 40GBASE-CR4-1M APF11200012UQQ Yes 0 1 QSFP 40GBASE-CR4-1M APF11200012UQQ Yes 0 2 QSFP 40GBASE-CR4-1M APF11200012UQQ Yes 0 3 QSFP 40GBASE-CR4-1M APF11200012UQQ Yes 0 4 QSFP 40GBASE-CR4-1M APF11200012UR1 Yes 0 5 QSFP 40GBASE-CR4-1M APF11200012UR1 Yes 0 6 QSFP 40GBASE-CR4-1M APF11200012UR1 Yes 0 7 QSFP 40GBASE-CR4-1M APF11200012UR1 Yes
PAGE 133
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820, S5000, S6000, S6000-ON, and Z9500. To view the successful and failed login details of the current user in the last 30 days or the custom defined period, use the show login statistics command. To view the successful and failed login details of all users in the last 30 days or the custom defined period, use the show login statistics all command.
PAGE 134
Unsuccessful login attempt(s) since the last successful login: 0 Unsuccessful login attempt(s) in last 11 day(s): 3 -----------------------------------------------------------------The following is sample output of the show login statistics unsuccessful-attempts command. Dell#show login statistics unsuccessful-attempts There were 3 unsuccessful login attempt(s) for user admin in last 30 day(s). The following is sample output of the show login statistics unsuccessful-attempts timeperiod days command.
PAGE 135
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced this version of the command for the S-Series. Usage Information The output for show memory displays the memory usage of LP part (sysdlp) of the system. The sysdlp is an aggregate task that handles all the tasks running on the S-Series’ CPU.
PAGE 136
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T.
PAGE 137
KP 0xbad9a000 evagt 0xbadb4000 ipc 0xbadc9000 sysReaper 0xbae22000 tme 0 0 0 0.00% 0.00% 0.00% 0 30 3 10000 0.00% 0.00% 0.00% 0 10 1 10000 0.00% 0.00% 0.00% 0 60 6 10000 0.00% 0.00% 0.02% 0 Dell#show processes cpu management-unit ? <1-99> Number of tasks with highest CPU usage last 5 seconds details Detail CPU utilization | Pipe through a command Dell#show processes cpu management-unit details CPUID 5sec 1min 5min -------------------------------CORE 0 11.73 10.79 12.
PAGE 138
0x00000253 0x00000206 0x00000012 0x0000024d Related Commands 100 140 1290 400 10 14 129 40 10000 10000 10000 10000 0.20% 0.20% 0.00% 0.00% 0.02% 0.02% 0.10% 0.08% 0.02% 0.03% 0.12% 0.14% 0 0 0 0 otm tnlmgr mount_mfs xstp show hardware layer2 acl — displays Layer 2 ACL data for the selected stack member and stack member port-pipe. show hardware layer3 — displays Layer 3 ACL or QoS data for the selected stack member and stack member port-pipe.
PAGE 139
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series and E-Series.
PAGE 140
IFMGR0 PORTMIRR0 IFMGR0 EVENTTERMLOG0 IFMGR0 IPSECMGR0 IFMGR0 DHCP0 IFMGR0 IPMGR0 IFMGR0 IFAGT3 IFAGT3 IFMGR0 IFMGR0 OFMGR0 IFMGR0 ACL0 IFMGR0 VRRP0 IFMGR0 PIM0 IFMGR0 MACMGR0 IFMGR0 L2PM0 IFMGR0 DIFFSERV0 IFMGR0 RTM0 IFMGR0 LLDP0 IFMGR0 MRTM0 IFMGR0 IPMGR1 IFMGR0 LACP0 PORTMIRR0 ACL_AGENT2 IFMGR0 IGMP0 IFMGR0 IFAGT2 Dell# 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 8 1 8 8 29 1 1 16 8 10 1 0 29 51 9 12 10 33 23 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
PAGE 141
Usage Information Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.7.1.0 Added the management-unit option. 7.6.1.0 Introduced on the S-Series.
PAGE 142
ifagt_1 21318 dsagt 6504 MacAgent 269778 Example (management-unit) 16564 0 0 21318 6504 269778 4754 6504 269778 Dell#show processes management-unit Total : 151937024, MaxUsed : 111800320 [2/25/2008 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 0 0 0 0 0 331 vrrp 5189632 249856 50572 0 50572 50572 323 frrp 5206016 241664 369238 0 369238 369238 322 xstp 7430144 2928640 38328 0 38
PAGE 143
• stack-unit unit-ID For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Enter the keyword stack-unit then the stack member number to display IFM information for that unit. NOTE: This option is only available on the S-Series. trace-flags Defaults Command Modes Command History Enter the keyword trace-flags to display IFM information for internal trace flags. none • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 144
show system Display the status of all stack members or a specific member. Syntax show system [brief | stack-unit unit-id | stack-ports {status | topology}] Parameters Command Modes Command History brief (OPTIONAL) Enter the keyword brief to view an abbreviated list of system information. stack-unit unit-id (OPTIONAL) Enter the keywords stack-unit then the stack member ID for information on that stack member. The unit ID range is from 1 to 6.
PAGE 145
-- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports ---------------------------------------------------------------1 Member not present 2 Management online S4048-ON S4048-ON 1-0(0-4160) 72 3 Member not present 4 Member not present 5 Member not present 6 Member not present -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) ----------------------------------------------2 1 up AC up 7048 2 2 down UNKNOWN down 0 -- Fan Status -Unit Bay TrayStatus Fan0 Speed Fan1 Speed ------------------
PAGE 146
Example (S4810) -- Unit 2 -Unit Type Status : Member Unit : not present -- Unit 3 -Unit Type Status : Member Unit : not present -- Unit 4 -Unit Type Status : Member Unit : not present -- Unit 5 -Unit Type Status : Member Unit : not present Dell#show system stack-unit 0 -- Unit 0 -Unit Type : Management Unit Status : online Next Boot : online Required Type : S6000 - 32-port TE/FG (SI) Current Type : S6000 - 32-port TE/FG (SI) Master priority : 0 Hardware Rev : 4.
PAGE 147
Unit Type : Management Unit Status : Card Problem - Software Failure Next Boot : online Required Type : S6000-ON - 32-port TE/FG (SI-ON) Current Type : S6000-ON - 32-port TE/FG (SI-ON) Master priority : 0 Hardware Rev : 3.0 Num Ports : 128 Up Time : 3 day, 22 hr, 33 min Dell Networking OS Version : 9-7(0-288) Jumbo Capable : yes POE Capable : no FIPS Mode : disabled Boot Flash : Present Boot Selector : 3.20.0.
PAGE 148
page (OPTIONAL) Enter the keyword page to view 24 lines of text at a time. Press the SPACE BAR to view the next 24 lines. Press the ENTER key to view the next line of text. When using the pipe command ( | ), enter one of these keywords to filter command output. For details about filtering commands, refer to CLI Basics. save Enter the keyword save to save the command output. flash: Save to local flash drive (flash://filename. A maximum of 20 characters.
PAGE 149
Example (S-Series) • show environment • show ip traffic • show ip management route • show ip route summary • show Inventory • show log summary • show command-history (last 20 commands) • show log Dell#show tech-support ? page Page through output stack-unit Unit Number | Pipe through a command Dell#show tech-support stack-unit 1 ? | Pipe through a command Dell#show tech-support stack-unit 1 | ? except Show only text that does not match a pattern find Search for the first occurrence
PAGE 150
------- show running-config ----------Current Configuration ... ! Version 9-4(0-168) ! Last configuration change at Tue Mar 25 17:43:06 2014 by admin ! boot system stack-unit 0 primary tftp://10.16.127.
PAGE 151
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.11.1 Introduced on the S-Series. telnet Connect through Telnet to a server. The Telnet client and server in Dell Networking support IPv4 and IPv6 connections. You can establish a Telnet session directly to the router or a connection can be initiated from the router. NOTE: The Telnet server and client are VRF-aware. Using the vrf parameter in this command, you can make a Telnet server or client to listen to a specific VRF.
PAGE 152
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 153
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.
PAGE 154
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series Original command. traceroute View a packet’s path to a specific device.
PAGE 155
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series ExaScale with IPv6. 8.1.1.0 Introduced on the E-Series ExaScale (IPv4 only). 7.9.1.0 Introduced VRF. 7.6.1.
PAGE 156
FTOS#traceroute 3ffe:501:ffff:100:201:e8ff:fe00:4c8b Type Ctrl-C to abort. ----------------------------------------------Tracing the route to 3ffe:501:ffff:100:201:e8ff:fe00:4c8b, 64 hops max, 60 byte packets ----------------------------------------------Hops Hostname Probe1 Probe2 Probe3 1 3ffe:501:ffff:100:201:e8ff:fe00:4c8b 000.000 ms 000.000 ms 000.000 ms Dell# Related Commands ping — tests the connectivity to a device. undebug all Disable all debug operations on the system.
PAGE 157
virtual-ip Configure a virtual IP address for the active management interface. You can configure virtual addresses both for IPv4 and IPv6 independently. Syntax virtual-ip {ipv4-address | ipv6-address} To return to the default, use the no virtual-ip {ipv4-address | ipv6-address} command. Parameters ipv4-address Enter the IP address of the active management interface in a dotted decimal format (A.B.C.D.). ipv6-address Enter an IPv6 address of the active management interface, in the x:x:x:x::x format.
PAGE 158
write Copy the current configuration to either the startup-configuration file or the terminal. Syntax write {memory compressed| terminal} Parameters memory Enter the keyword memory to copy the current running configuration to the startup configuration file. This command is similar to the copy runningconfig startup-config command. compressed Enter the keyword compressed to write the operating configuration to the startup-config file in the compressed mode.
PAGE 159
5 802.1ag 802.1ag is available on the Dell Networking OS. ccm disable Disable continuity check message (CCM). Syntax ccm disable Enter no ccm disable to enable CCM. Defaults Disabled Command Modes ECFM DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 160
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.
PAGE 161
Command Modes ECFM DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 162
Parameters name Name the maintenance domain. md-level number Enter a maintenance domain level. The range is from 0 to 7. Defaults none Command Modes ETHERNET CFM Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 163
ethernet cfm mep Create an MEP. Syntax Parameters ethernet cfm mep {up-mep | down-mep} domain {name | level} ma-name name mepid mep-id [up-mep | downmep] Specify whether the MEP is up or down facing. • Up-MEP: monitors the forwarding path internal to a bridge on the customer or provider edge; on Dell Networking systems, the internal forwarding path is effectively the switch fabric and forwarding engine. • Down-MEP: monitors the forwarding path external to another bridge.
PAGE 164
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.
PAGE 165
mep cross-check enable Enable cross-checking. Syntax Parameters mep cross-check enable {port | vlan-id} port Down service with no VLAN association. vlan-id Enter the VLAN to apply the cross-check. Defaults none Command Modes ECFM DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 166
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series. ping ethernet Send a loopback message. Syntax ping ethernet domain [name l level] ma-name ma-name remote {dest-mep-id | mac-addr mac-address} source {src-mep-id | port interface} Parameters name | level Enter the domain name or level. ma-name ma-name Enter the keyword ma-name and then enter the maintenance association name.
PAGE 167
Parameters name | level Enter the maintenance domain name or level. brief Enter the keyword brief to display a summary output. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 168
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the S-Series.
PAGE 169
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the S-Series.
PAGE 170
show ethernet cfm statistics Display MEP statistics. Syntax show ethernet cfm statistics [domain {name | level} vlan-id vlan-id mpid mpid] Parameters domain Enter the keyword domain to display statistics for a particular domain. name | level Enter the domain name or level. vlan-id vlan-id Enter the keyword vlan-id then a VLAN ID. mpid mpid Enter the keyword mpid then a maintenance point ID. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 171
slot/port[] Enter the slot and port numbers for the port. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.
PAGE 172
Example Version Description Version 8.3.19.0 Introduced on the S4820T. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the S-Series.
PAGE 173
traceroute cache hold-time Set the amount of time a trace result is cached. Syntax Parameters traceroute cache hold-time minutes minutes Enter a hold-time. The range is from 10 to 65535 minutes. Defaults 100 minutes Command Modes ETHERNET CFM Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 174
Version Description 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the S-Series. traceroute ethernet Send a linktrace message to an MEP. Syntax traceroute ethernet domain [name | level] ma-name remote {mep-id mep-id | mac-addr mac-address} Parameters domain name | level Enter the keyword domain then the domain name or level. ma-name ma-name Enter the keyword ma-name then the maintenance association name. mepid mep-id Enter the MEP ID that is the trace target.
PAGE 175
6 802.1X An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. The Dell Networking operating software supports remote authentication dial-in service (RADIUS) and active directory environments using 802.1X Port Authentication.
PAGE 176
interface interface Restricts the debugging information to an interface. Defaults Disabled Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 177
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series. If the host responds to 802.1X with an incorrect login/password, the login fails.
PAGE 178
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x auth-type mab-only To authenticate a device with MAC authentication bypass (MAB), only use the host MAC address.
PAGE 179
In MAB-only authentication mode, a port authenticates using the host MAC address even though 802.1xauthentication is enabled. If the MAB-only authentication fails, the host is placed in the guest VLAN (if configured). To disable MAB-only authentication on a port, enter the no dot1x auth-type mab-only command. Related Commands dot1x mac-auth-bypass — Enable MAC authentication bypass. dot1x authentication (Configuration) Enable dot1x globally. Enable dot1x both globally and at the interface level.
PAGE 180
To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 181
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series. 1X authentication is enabled when an interface is connected to the switch.
PAGE 182
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 183
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Introduced on the C-Series and S-Series.
PAGE 184
Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x max-supplicants Restrict the number of supplicants that can be authenticated and permitted to access the network through the port. This configuration is only takes effect in Multi-auth mode.
PAGE 185
dot1x port-control Enable port control on an interface. Syntax Parameters dot1x port-control {force-authorized | auto | force-unauthorized} force-authorized Enter the keywords force-authorized to forcibly authorize a port. auto Enter the keyword auto to authorize a port based on the 802.1X operation result. force-unauthorized Enter the keywords force-unauthorized to forcibly de-authorize a port. Defaults none Command Modes Auto Command History This guide is platform-specific.
PAGE 186
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.
PAGE 187
Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauth-max Configure the maximum number of times a port can re-authenticate before the port becomes unauthorized. Syntax dot1x reauth-max number To return to the default, use the no dot1x reauth-max command.
PAGE 188
dot1x server-timeout Configure the amount of time after which exchanges with the server time-out. Syntax dot1x server-timeout seconds To return to the default, use the no dot1x server-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 189
dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out. Syntax dot1x supplicant-timeout seconds To return to the default, use the no dot1x supplicant-timeout command. Parameters seconds Enter a time-out value in seconds. The range is from 1 to 300, where 300 is implementation dependant. The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 190
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 191
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Introduced on the C-Series and S-Series.
PAGE 192
show dot1x interface Display the 802.1X configuration of an interface. Syntax show dot1x interface interface [mac-address mac-address] Parameters interface mac-address Defaults Enter one of the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. (Optional) MAC address of a supplicant.
PAGE 193
Re-Authentication: Untagged VLAN id: Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: Dell# Example (macaddress) Disable 400 Enable 100 Disable NONE NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Authenticated Idle Dell#show dot1x interface gig
PAGE 194
Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Max-Supplicants: NONE Enable Enable 3 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 MULTI_AUTH 128 Port status and State info for Supplicant: 00:00:00:00:00:11 Port Auth Status: Untagged VLAN id: Auth PAE State: Backend State: Dell# 194 802.
PAGE 195
7 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell Networking OS.
PAGE 196
Command History • CONFIGURATION-EXTENDED-ACCESS-LIST • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 197
Command Modes Command History • CONFIGURATION-STANDARD-ACCESS-LIST • CONFIGURATION-EXTENDED-ACCESS-LIST • CONFIGURATION-MAC ACCESS LIST-STANDARD • CONFIGURATION-MAC ACCESS LIST-EXTENDED This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 198
access-class Apply a standard ACL to a terminal line. Syntax access-class access-list-name [ipv4 | ipv6] To remove an ACL, use the no access-class access-list-name [ipv4 | ipv6] command. Parameters access-list-name Enter the name of a configured Standard ACL, up to 140 characters. ipv4 Enter the keyword ipv4 to configure an IPv4 access class. ipv6 Enter the keyword ipv6 to configure an IPv6 access class. Defaults Not configured.
PAGE 199
you can set up two different types of access classes with each class processing either IPv4 or IPv6 rules separately. However, if you already have configured generic IP ACL on a terminal line, then you cannot further apply IPv4 or IPv6 specific filtering on top of this configuration. Because, both IPv4 and IPv6 access classes are already configured on this terminal line. Before applying either IPv4 or IPv6 filtering, first undo the generic configuration using the no access-class access-list-name command.
PAGE 200
ip access-group Assign an IP access list (IP ACL) to an interface. Syntax ip access-group access-list-name {in | out} [implicit-permit] [vlan vlanid] [vrf vrf-name] To delete an IP access-group configuration, use the no ip access-group access-list-name {in | out} [implicit-permit] [vlan vlan-id] [vrf vrf-name] command. Parameters access-list-name Enter the name of a configured access list, up to 140 characters. in Enter the keyword in to apply the ACL to incoming traffic.
PAGE 201
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. You can assign one ACL (standard or extended ACL) to an interface. NOTE: This command supports Loopback interfaces EE3 and EF series route processor modules (RPMs). This command does not support Loopback interfaces ED series RPMs and S-Series Loopback interfaces.
PAGE 202
Parameters Command Modes Command History access-list-name Enter the name of the ACL to be displayed. cam_count List the count of the CAM rules for this ACL. interface interface Enter the keyword interface then the one of the following keywords and slot/ port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 203
show ip accounting access-lists Description “order 4” Displays the QoS order of priority for the ACL entry. Field Example Dell#show ip accounting access-list L3-ACL vrf vrf3 ! Standard Ingress IP access list L3-ACL on vrf3 Total cam count 3 seq 5 permit 10.1.2.0/24 seq 10 permit 20.1.2.0/24 seq 15 permit 30.1.2.
PAGE 204
Version Description 8.3.7.0 Introduced on the S4810. Standard IP ACL Commands When you create an ACL without any rule and then apply it to an interface, the ACL behavior reflects an implicit permit. The platform supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types and Common IP ACL Commands sections. deny To drop packets with a certain IP address, configure a filter.
PAGE 205
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Add the DSCP value for ACL matching.
PAGE 206
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 207
Parameters source Enter the IP address in dotted decimal format of the network from which the packet was sent. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. any Enter the keyword any to specify that all routes are subject to the filter. You can enter any of the following keywords to specify route types. • bytes — Enter the keyword bytes to count bytes processed by the filter.
PAGE 208
Version Description 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the “Quality of Service” chapter of the Dell Networking OS Configuration Guide. Related Commands deny — assigns a IP ACL filter to deny IP packets. ip access-list standard — creates a standard ACL.
PAGE 209
Usage Information Version Description 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. When you have exhausted all the sequence numbers, this feature permits re-assigning a new sequence number to entries of an existing access-list.
PAGE 210
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.
PAGE 211
The platform supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types and Common IP ACL Commands sections. deny Configure a filter that drops IP packets meeting the filter criteria.
PAGE 212
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 213
deny icmp To drop all or specific internet control message protocol (ICMP) messages, configure a filter. Syntax deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} [dscp] [count [byte] [order] [fragments] [no-drop] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny icmp {source mask | any | host ip-address} {destination mask | any | host ip-address} command.
PAGE 214
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series ExaScale. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry.
PAGE 215
operator port port (OPTIONAL) Enter one of the following logical operand: • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for the port command) Enter the application layer port number. Enter two port numbers if using the range logical operand. The range is from 0 to 65535.
PAGE 216
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the keyword dscp. 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. Deprecated the keyword established. 6.5.1.
PAGE 217
Related Commands deny — assigns a filter to deny IP traffic. deny udp — assigns a filter to deny UDP traffic. deny udp To drop user datagram protocol (UDP) packets meeting the filter criteria, configure a filter.
PAGE 218
no-drop Enter the keywords no-drop to match only the forwarded packets. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 219
Example An ACL rule with a TCP port range of 4000–8000 uses eight entries in the CAM.
PAGE 220
Usage Information Version Description 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. The number of entries allowed per ACL is hardware-dependent.
PAGE 221
lowest; lower-order numbers have a higher priority). If you do not use the keyword order, the ACLs have the lowest order by default (255). fragments Enter the keyword fragments to use ACLs to control packet fragments. no-drop Enter the keywords no-drop to match only the forwarded packets. Defaults Not configured. Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific.
PAGE 222
permit tcp To pass TCP packets meeting the filter criteria, configure a filter. Syntax permit tcp {source mask | any | host ip-address} [bit] [operator port [port]] {destination mask | any | host ip-address} [bit] [dscp] [operator port [port]] [count [byte] [order] [fragments] [no-drop] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 223
mask Enter a network mask in /prefix format (/x) or A.B.C.D. The mask, when specified in A.B.C.D format, may be either contiguous or non-contiguous. count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes. order (OPTIONAL) Enter the keyword order to specify the QoS priority for the ACL entry.
PAGE 224
The S-Series cannot count both packets and bytes; when you enter the count byte options, only bytes increment. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. Most ACL rules require one entry in the CAM. However, rules with TCP and UDP port operators (for example, gt, lt, or range) may require more than one entry.
PAGE 225
any Enter the keyword any to specify that all routes are subject to the filter. host ip-address Enter the keyword host and then enter the IP address to specify a host IP address. dscp Enter the keyword dscp to deny a packet based on the DSCP value. The range is from 0 to 63.
PAGE 226
Usage Information Version Description 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added support for non-contiguous mask and added the monitor option. . 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The order option is relevant in the context of the Policy QoS feature only.
PAGE 227
resequence access-list Re-assign sequence numbers to entries of an existing access-list. Syntax Parameters Defaults Command Modes Command History resequence access-list {ipv4 | mac} {access-list-name StartingSeqNum Stepto-Increment} ipv4 | mac Enter the keyword ipv4or mac to identify the access list type to resequence. access-list-name Enter the name of a configured IP access list, up to 140 characters. StartingSeqNum Enter the starting sequence number to resequence.
PAGE 228
seq Assign a sequence number to a deny or permit filter in an extended IP access list while creating the filter. Syntax seq sequence-number {deny | permit} {ip-protocol-number | icmp | ip | tcp | udp} {source mask | any | host ip-address} {destination mask | any | host ip-address} [operator port [port]] [count [byte] | log] [dscp value] [order] [monitor] [fragments] [no-drop] Parameters sequence-number Enter a number from 0 to 4294967290.
PAGE 229
destination Enter the IP address of the network or host to which the packets are sent. count (OPTIONAL) Enter the keyword count to count packets the filter processes. byte (OPTIONAL) Enter the keyword byte to count bytes the filter processes. log (OPTIONAL, E-Series only) Enter the keyword log to enter ACL matches in the log. Supported on Jumbo-enabled line cards only. dscp (OPTIONAL) Enter the keyword dcsp to match to the IP DCSCP values.
PAGE 230
Usage Information Version Description 7.4.1.0 Added support for the non-contiguous mask and added the monitor option. Deprecated the keyword established. 6.5.10 Expanded to include the optional QoS order priority for the ACL entry. The monitor option is relevant in the context of flow-based monitoring only. For more information, refer to Port Monitoring. The order option is relevant in the context of the Policy QoS feature only.
PAGE 231
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 232
NOTE: 1. If the MAC ACL is applied on VLAN, none of the VLAN members should have an access list applied for that VLAN. 2. If the MAC ACL is applied on a Physical or Port Channel interface, the VLAN in which this port is associated should not have an access list applied. 3. If the MAC ACL is applied on a VLAN, then that VLAN should not belong to VLAN ACL group. 4. If the MAC ACL is applied on a VLAN ACL group, then none of the VLANs in that group should have an access list applied on it.
PAGE 233
Parameters access-list-name Enter the name of a configured MAC ACL, up to 140 characters. interface interface Enter the keyword interface then the one of the following keywords and slot/ port or number information: in | out • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 234
• in | out Command Modes Command History • EXEC • EXEC Privilege For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Identify whether ACL is applied on ingress or egress side. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 235
NOTE: For more information, also refer to the Commands Common to all ACL Types and Common MAC Access List Commands sections. deny To drop packets with a the MAC address specified, configure a filter. Syntax deny {any | mac-source-address [mac-source-address-mask]} [count [byte]] [log] [monitor] To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 236
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. When you use the log option, the CP processor logs detail the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When you configure ACL logging and byte counters simultaneously, byte counters may display an incorrect value.
PAGE 237
Usage Information Version Description 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Dell Networking OS supports one ingress and one egress MAC ACL per interface. The number of entries allowed per ACL is hardware-dependent.
PAGE 238
to the monitored interface. For more information, refer to the “Flow-based Monitoring” section in the Port Monitoring chapter of the Dell Networking OS Configuration Guide. Defaults Not configured. Command Modes CONFIGURATION-MAC ACCESS LIST-STANDARD Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 239
• Parameters Use the no deny {any | mac-source-address mac-source-address-mask} command. any Enter the keyword any to specify that all routes are subject to the filter. mac-sourceaddress Enter a MAC address in nn:nn:nn:nn:nn:nn format. mac-sourceaddress-mask (OPTIONAL) Specify which bits in the MAC address must match. If no mask is specified, a mask of 00:00:00:00:00:00 is applied (in other words, the filter allows only MAC addresses that match).
PAGE 240
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When you configure the ACL logging and byte counters simultaneously, byte counters may display an incorrect value.
PAGE 241
mac-sourceaddress-mask Specify which bits in the MAC address must match. The MAC ACL supports an inverse mask; therefore, a mask of ff:ff:ff:ff:ff:ff allows entries that do not match and a mask of 00:00:00:00:00:00 only allows entries that match exactly. mac-destinationaddress Enter the destination MAC address and mask in nn:nn:nn:nn:nn:nn format. mac-destinationaddress-mask Specify which bits in the MAC address must match.
PAGE 242
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Added the monitor option. 6.1.1.0 Introduced on the E-Series. When you use the log option, the CP processor logs detail the packets that match.
PAGE 243
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names were up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.
PAGE 244
To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit {any | host mac-address | mac-source-address mac-sourceaddress-mask} {any | mac-destination-address mac-destination-addressmask} command. any Enter the keyword any to forward all packets. host Enter the keyword host then a MAC address to forward packets with that host address.
PAGE 245
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series.
PAGE 246
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 247
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 248
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information Prefix lists redistribute OSPF and RIP routes meeting specific criteria. Related Commands show ip route list — displays IP routes in an IP prefix list.
PAGE 249
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series.
PAGE 250
Example Version Description 6.1.1.0 Introduced on the E-Series. Dell(conf-nprefixl)#show config ! ip prefix-list snickers Dell(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists. Syntax show ip prefix-list detail [prefix-name] Parameters Command Modes Command History prefix-name • EXEC • EXEC Privilege (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters. This guide is platform-specific.
PAGE 251
seq 10 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 25 permit 192.0.0.0 bitmask 192.0.0.0 (hit count: 800) show ip prefix-list summary Display a summary of the configured prefix lists. Syntax Parameters Command Modes Command History show ip prefix-list summary [prefix-name] prefix-name • EXEC • EXEC Privilege (OPTIONAL) Enter a text string as the name of the prefix list, up to 140 characters. This guide is platform-specific.
PAGE 252
Route Map Commands When you create an access-list without any rule and then applied to an interface, the ACL behavior reflects implicit permit. To configure route maps and their redistribution criteria, use the following commands. continue To a route-map entry with a higher sequence number, configure a route-map. Syntax continue [sequence-number] Parameters sequence-number (OPTIONAL) Enter the route map sequence number. The range is from 1 to 65535. Defaults Not configured.
PAGE 253
• A successful match with a continue clause, the route map executes the set clauses and then goes to the specified route map entry upon execution of the continue clause. • If the next route map entry contains a continue clause, the route map executes the continue clause if a successful match occurs. • If the next route map entry does not contain a continue clause, the route map evaluates normally.
PAGE 254
Related Commands Version Description 8.1.1.0 Introduced on the E-Series ExaScale. pre-7.7.1.0 Introduced. route-map — enables a route map. match as-path To match routes that have a certain AS number in their BGP path, configure a filter. Syntax match as-path as-path-name To delete a match AS path filter, use the no match as-path as-path-name command. Parameters as-path-name Enter the name of an established AS-PATH ACL, up to 140 characters. Defaults Not configured.
PAGE 255
To delete a community match filter, use the no match community command. Parameters community-listname Enter the name of a configured community list. exact (OPTIONAL) Enter the keywords exact to process only those routes with this community list name. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 256
• For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 257
To delete a match, use the no match ip address prefix-list-name command. Parameters prefix-list-name Enter the name of configured prefix list, up to 140 characters. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 258
To delete a match, use the no match ip next-hop {prefix-list prefix-list-name} command. Parameters prefix-list prefix-listname Enter the keywords prefix-list and then enter the name of configured prefix list, up 10 140 characters. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 259
To delete a match, use the no match ip route-source {prefix-list prefix-list-name} command. Parameters prefix-list prefix-listname Enter the keywords prefix-list and then enter the name of configured prefix list, up to 140 characters. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 260
To delete a value, use the no match metric [metric-value] command. Parameters metric-value Enter a value to match. The range is from zero (0) to 4294967295. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.
PAGE 261
igp Enter the keyword igp to match routes originating within the same AS. incomplete Enter the keyword incomplete to match routes with incomplete routing information. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 262
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 263
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.
PAGE 264
Defaults Not configured. If you do not define a keyword (permit or deny) for the route map, the permit action is the default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 265
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 266
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. set level — specify the OSPF area for route redistribution.
PAGE 267
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 268
All routes with the NO_EXPORT (0xFFFFFF01) community attribute must not be advertised outside a BGP confederation boundary. none Enter the keyword none to remove the community attribute from routes meeting the route map criteria. additive (OPTIONAL) Enter the keyword additive to add the communities to already existing communities. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific.
PAGE 269
level-1-2 Enter the keyword level-1-2 to redistribute matched routes to IS-IS Level 1 and Level 2. level-2 Enter the keyword level-2 to redistribute matched routes to IS-IS Level 2. stub-area Enter the keyword stub to redistributed matched routes to OSPF stub areas. Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Dell Networking OS Line Reference Guide.
PAGE 270
Defaults Not configured. Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 271
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.
PAGE 272
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Implemented the keyword internal. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 273
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 274
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. set tag To specify a tag for redistributed routes, configure a filter. Syntax set tag tag-value To delete a setting, use the no set tag command.
PAGE 275
set level — specifies the OSPF area for route redistribution. set metric — specifies the metric value assigned to redistributed routes. set metric-type — specifies the route type assigned to redistributed routes. set weight To add a non-RFC compliant attribute to the BGP route to assist with route selection, configure a filter. Syntax set weight weight To delete a weight specification, use the no set weight weight command.
PAGE 276
show config Display the current route map configuration. Syntax show config Command Modes ROUTE-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.
PAGE 277
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.
PAGE 278
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long.
PAGE 279
Example Version Description pre-Version 6.1.1.0 Introduced on the E-Series. Dell#show ip as-path-access-lists ip as-path access-list acc permit 750 deny 10 IP Community List Commands IP community list commands are supported on the Dell Networking OS. ip community-list Enter COMMUNITY-LIST mode and create an IP community-list for BGP. Syntax ip community-list comm-list-name To delete a community-list, use the no ip community-list comm-list-name command.
PAGE 280
show ip community-lists Display configured IP community lists in alphabetic order. Syntax show ip community-lists [name] Parameters Command Modes Command History name • EXEC • EXEC Privilege (OPTIONAL) Enter the name of the standard or extended IP community list, up to 140 characters. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 281
Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 282
permit — configures a permit filter. deny (for Extended IP ACLs) Configure a filter that drops IP packets meeting the filter criteria.
PAGE 283
packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 284
Command Modes Command History Usage Information CONFIGURATION-STANDARD-ACCESS-LIST Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 285
Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 286
deny udp — assigns a filter to deny UDP traffic. deny udp (for Extended IP ACLs) To drop user datagram protocol (UDP) packets meeting the filter criteria, configure a filter.
PAGE 287
Related Commands deny — assigns a filter to deny IP traffic. deny tcp — assigns a filter to deny TCP traffic. deny arp (for Extended MAC ACLs) Configure an egress filter that drops ARP packets on egress ACL supported line cards. (For more information, refer to your line card documentation).
PAGE 288
Usage Information Version Description 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero.
PAGE 289
monitor Defaults (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface. By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled.
PAGE 290
Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no deny ether-type protocol-type-number {destination-mac-address mac-address-mask | any} vlan vlan-id {source-mac-address mac-addressmask | any} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 291
standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port. The source port is the monitored port (MD) and the destination port is the monitoring port (MG). deny (for Standard MAC ACLs) To drop packets with a the MAC address specified, configure a filter.
PAGE 292
packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 293
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-MAC ACCESS LIST-EXTENDED Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 294
Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number. • Use the no permit {source [mask] | any | host ip-address} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 295
Related Commands deny — Assigns a IP ACL filter to deny IP packets. ip access-list standard — Creates a standard ACL. permit arp (for Extended MAC ACLs) Configure a filter that forwards ARP packets meeting this criteria. This command is supported only on 12-port GE line cards with SFP optics; refer to your line card documentation for specifications.
PAGE 296
Usage Information When the configured maximum threshold is exceeded, generation of logs is stopped. When the interval at which ACL logs are configured to be recorded expires, the subsequent, fresh interval timer is started and the packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval.
PAGE 297
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.
PAGE 298
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes.
PAGE 299
permit udp (for Extended IP ACLs) To pass UDP packets meeting the filter criteria, configure a filter. Syntax permit udp {source mask | any | host ip-address} [operator port [port]] {destination mask | any | host ip-address} [dscp] [operator port [port]] [count [byte]] [order] [fragments] [log [interval minutes] [threshold-inmsgs [count]][monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 300
MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode.
PAGE 301
Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added the support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added the support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 302
• Parameters Defaults Use the no permit {any | mac-source-address mac-source-address-mask} command. log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 303
Related Commands deny — configures a MAC ACL filter to drop packets. seq —configure a MAC ACL filter with a specified sequence number. seq (for Standard MAC ACLs) To a deny or permit filter in a MAC access list while creating the filter, assign a sequence number. Syntax seq sequence-number {deny | permit} {any | mac-source-address [mac-sourceaddress-mask]} [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, use the no seq sequence-number command.
PAGE 304
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 305
The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.
PAGE 306
Syntax seq sequence-number {deny | permit} arp {destination-mac-address macaddress-mask | any} vlan vlan-id {ip-address | any | opcode code-number} [count [byte]] [order] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages.
PAGE 307
both the ingress and egress direction. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You may specify traffic using standard or extended access-lists. This mechanism copies all incoming or outgoing packets on one port and forwards (mirrors) them to another port.
PAGE 308
Usage Information Version Description 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. 9.3.0.0 Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 309
Defaults By default, 10 ACL logs are generated if you do not specify the threshold explicitly. The default frequency at which ACL logs are generated is five minutes. By default, flow-based monitoring is not enabled. Command Modes Command History Usage Information CONFIGURATION-EXTENDED-ACCESS-LIST Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4(0.
PAGE 310
To delete a filter, use the no seq sequence-number command. Parameters Defaults log (OPTIONAL) Enter the keyword log to enable the triggering of ACL log messages. threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminate with the seq, permit, or deny commands. The threshold range is from 1 to 100.
PAGE 311
permit udp (for IPv6 ACLs) Configure a filter to pass UDP packets meeting the filter criteria. Syntax permit udp {source address mask | any | host ipv6-address} [operator port [port]] {destination address | any | host ipv6-address} [operator port [port]] [count [byte]] [log [interval minutes] [threshold-in-msgs [count]] [monitor] To remove this filter, you have two choices: Parameters Defaults • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 312
MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces. You can activate flow-based monitoring for a monitoring session by entering the flow-based enable command in the Monitor Session mode.
PAGE 313
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms. When the configured maximum threshold is exceeded, generation of logs is stopped.
PAGE 314
the generation of ACL logs is terminated with the seq, permit, or deny commands. The threshold range is from 1 to 100. Defaults interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The interval range is from 1 to 10 minutes. monitor (OPTIONAL) Enter the keyword monitor when the rule is describing the traffic that you want to monitor and the ACL in which you are creating the rule is applied to the monitored interface.
PAGE 315
permit (for IPv6 ACLs) To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP.
PAGE 316
If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs. You can configure ACL logging only on ACLs that are applied to ingress interfaces; you cannot enable logging for ACLs that are associated with egress interfaces.
PAGE 317
Command History Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, Z9000, and MXL 10/40GbE Switch IO Module platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, Z9000, and MXL 10/40GbE Switch IO Module platforms.
PAGE 318
Defaults threshold-in msgs count (OPTIONAL) Enter the threshold-in-msgs keyword followed by a value to indicate the maximum number of ACL logs that can be generated, exceeding which the generation of ACL logs is terminated. with the seq, permit, or deny commands. The threshold range is from 1 to 100.. interval minutes (OPTIONAL) Enter the keyword interval followed by the time period in minutes at which ACL logs must be generated. The time interval range is from 1 to 10 minutes.
PAGE 319
deny icmp (for Extended IPv6 ACLs) Configure a filter to drop all or specific ICMP messages. NOTE: Only the options that have been newly introduced in Release 9.3(0.0) and Release 9.4(0.0) are described here. For a complete description on all of the keywords and variables that are available with this command, refer the topic of this command discussed earlier in this guide.
PAGE 320
packet count for that new interval commences from zero. If ACL logging was stopped previously because the configured threshold is exceeded, it is re-enabled for this new interval. If ACL logging is stopped because the configured threshold is exceeded, it is re-enabled after the logging interval period elapses. ACL logging is supported for standard and extended IPv4 ACLs, IPv6 ACLs, and MAC ACLs.
PAGE 321
Command Modes Command History Usage Information ACCESS-LIST Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the no-drop parameter. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Added support for flow-based monitoring on the S4810, S4820T, S6000, and Z9000 platforms. 9.3(0.0) Added support for logging of ACLs on the S4810, S4820T, and Z9000 platforms.
PAGE 322
8 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This chapter describes the access control list (ACL) virtual local area network (VLAN) group and content addressable memory (CAM) enhancements. member vlan Add VLAN members to an ACL VLAN group. Syntax member vlan {VLAN-range} Parameters VLAN-range Enter the member VLANs using comma-separated VLAN IDs, a range of VLAN IDs, a single VLAN ID, or a combination.
PAGE 323
ip access-group Apply an egress IP ACL to the ACL VLAN group. Syntax Parameters ip access-group {group name} out implicit-permit group-name Enter the name of the ACL VLAN group where you want the egress IP ACLs applied, up to 140 characters. out Enter the keyword out to apply the ACL to outgoing traffic.
PAGE 324
Version Description 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms Usage Information When an ACL-VLAN-Group name or the Access List Group Name contains more than 30 characters, the name is truncated in the show acl-vlan-group command output. Examples The following sample illustrates the output of the show acl-vlan-group command. NOTE: Some group names and some access list names are truncated.
PAGE 325
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T, Z9000 and MXL platforms After CAM configuration for ACL VLAN groups is performed, you must reboot the system to enable the settings to be stored in nonvolatile storage. During the initialization of CAM, the chassis manager reads the NVRAM and allocates the dynamic VCAP regions.
PAGE 326
vlaniscsi <0-2> Allocate the number of FP blocks for VLAN iSCSI counters. vlanaclopt <0-2> Allocate the number of FP blocks for the ACL VLAN optimization feature. Default If you use the default keyword with the cam-acl-vlan command, the FP blocks allocated for VLAN processes are restored to their default values. No FP blocks or dynamic VLAN Content Aware Processor (VCAP) groups are allocated for VLAN operations by default.
PAGE 327
Usage Information The following regions must be provided in the show cam-usage output: • L3AclCam • L2AclCam • V6AclCam The following table describes the output fields of this show command: Field Description LineCard Number of the line card that contains information on ACL VLAN groups Portpipe The hardware path that packets follow through a system for ACL optimization CAM-Region Type of area in the CAM block that is used for ACL VLAN groups Total CAM space Total amount of space in the CAM b
PAGE 328
199 Codes: * - cam usage is above 90%.
PAGE 329
show running config acl-vlan-group Display the running configuration of all or a given ACL VLAN group. Syntax Parameters show running config acl-vlan-group group name group-name Default None Command Modes EXEC Display only the ACL VLAN group that is specified. The maximum group name is 140 characters. EXEC Privilege Command History Examples Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.
PAGE 330
Command History Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3.(0.0) Introduced on the S4810, S4820T and Z9000 platforms You can have up to eight different ACL VLAN groups at any given time. When you configure an ACL VLAN group, you enter the ACL VLAN Group Configuration mode.
PAGE 331
Examples The following sample output shows the line-by-line style display when using the show acl-vlan-group detail option. Note that no group or access list names are truncated Dell#show acl-vlan-group detail Group Name : Test Egress IP Acl : Ingress IP Acl : test Ingress IPV6 Acl : Vlan Members : 1-100 description (ACL VLAN Group) Add a description to the ACL VLAN group. Syntax Parameters description description description Enter a description to identify the ACL VLAN group (80 characters maximum).
PAGE 332
9 Bidirectional Forwarding Detection (BFD) Bidirectional forwarding detection (BFD) is a detection protocol that provides fast forwarding path failure detection.
PAGE 333
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 9.2(1.0) Introduced on the Z9500. 9.2.(0.
PAGE 334
Re-enable BFD using the no bfd disable command. Defaults BFD is disabled by default. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 335
Version Description 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. bfd enable (Interface) Enable BFD on an interface. Syntax bfd enable Defaults BFD is enabled on all interfaces when you enable BFD from CONFIGURATION mode. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 336
min_rx milliseconds Enter the keywords min_rx to specify the minimum rate at which the local system would like to receive control packets from the remote system. The range is from 50 to 1000. The default is 200. multiplier value Enter the keywords multiplier to specify the number of packets that must be missed in order to declare a session down. The range is from 3 to 50. The default is 3.
PAGE 337
Parameters ip-address Enter the IP address of the neighbor in dotted decimal format (A.B.C.D). Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 338
Usage Information Version Description 7.4.1.0 Introduced on the E-Series. Protocol Liveness is a feature that notifies the BFD Manager when a client protocol (for example, OSPF and ISIS) is disabled. When a client is disabled, all BFD sessions for that protocol are torn down. Neighbors on the remote system receive an Admin Down control packet and are placed in the Down state. Peer routers might take corrective action by choosing alternative paths for the routes that originally pointed to this router.
PAGE 339
Version Description 9.2.(0.0) Introduced on Z9000, S4810, and S4820T. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. ipv6 ospf bfd all-neighbors Establish BFD sessions with all OSPFv3 neighbors on a single interface or use non-default BFD session parameters.
PAGE 340
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2.0.0 Introduced on the Z9000, S4820T, and S4810. This command provides the flexibility to fine-tune the timer values based on individual interface needs when you configure ipv6 ospf BFD in CONFIGURATION mode. Any timer values specified with this command overrides timers set using the bfd all-neighbors command. Using the no form of this command does not disable BFD if you configure BFD in CONFIGURATION mode.
PAGE 341
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on S4810. 8.2.1.
PAGE 342
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.3 Introduced on the E-Series ExaScale.
PAGE 343
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. 8.4.1.3 Introduced on the E-Series ExaScale. When you explicitly disable a BGP neighbor for a BFD session with the neighbor bfd disable command: • The neighbor does not inherit the global BFD disable values configured with the bfd neighbor command or configured for the peer group to which the neighbor belongs.
PAGE 344
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.
PAGE 345
Number of messages from IFA about port state change: 0 Number of messages communicated b/w Manager and Agent: 6 Dell# Related Commands bfd all-neighbors — establishes BFD sessions with all neighbors discovered by the IS-IS protocol or OSPF protocol out of all interfaces. vrrp bfd neighbor Establish a BFD for VRRP session with a neighbor. Syntax vrrp bfd neighbor ip-address To remove the BFD session with the neighbor, use the no vrrp bfd neighbor ip-address command.
PAGE 346
10 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called neighbors or peers) exchange information including full routing tables and periodically sent messages to update those routing tables.
PAGE 347
NOTE: It will not be possible to enable VRF mode for IPv6 unicast without configuring the corresponding IPv4 unicast mode for the same VRF. While deletion, whenever the IPv4 VRF mode is deleted for the VRF, it will automatically delete the IPv6 VRF configurations as well. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 348
Defaults summary-only (OPTIONAL) Enter the keyword summary-only to advertise only the aggregate address. Specific routes are not advertised. suppress-map mapname (OPTIONAL) Enter the keywords suppress-map then the name of a configured route map to identify which more-specific routes in the aggregate are suppressed. Not configured. Command Modes Command History • ROUTER BGP ADDRESS FAMILY • ROUTER BGP ADDRESS FAMILY IPv6 This guide is platform-specific.
PAGE 349
The attribute-map corresponding to an aggregate address is applied during the outbound update creation time; hence the value set in that attribute-map will not be shown in the output of the show ip bgp aggregate route command. bgp add-path Allow the advertisement of multiple paths for the same address prefix without the new paths replacing any previous ones.
PAGE 350
bgp always-compare-med Allows you to enable comparison of the MULTI_EXIT_DISC (MED) attributes in the paths from different external ASs. Syntax bgp always-compare-med To disable comparison of MED, enter no bgp always-compare-med. Defaults Disabled (that is, the software only compares MEDs from neighbors within the same AS). Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 351
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 352
bgp bestpath as-path ignore Ignore the AS PATH in BGP best path calculations. Syntax bgp bestpath as-path ignore To return to the default, enter the no bgp bestpath as-path ignore command. Defaults Disabled (that is, the software considers the AS_PATH when choosing a route as best). Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 353
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.4 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. The bestpath router bgp configuration mode command changes the default bestpath selection algorithm.
PAGE 354
Usage Information The software compares the MEDs only if the path contains no external autonomous system numbers. If you enable this command, use the clear ip bgp * command to recompute the best path. bgp bestpath med missing-as-best During path selection, indicate preference to paths with missing MED (MULTI_EXIT_DISC) over paths with an advertised MED attribute. Syntax bgp bestpath med missing-as-best To return to the default selection, use the no bgp bestpath med missing-as-best command.
PAGE 355
Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000.
PAGE 356
Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Usage Information Route reflection to clients is not necessary if all client routers are fully meshed. Related Commands bgp cluster-id — assigns an ID to a BGP cluster with two or more route reflectors. neighbor route-reflector-client — configures a route reflector and clients. bgp cluster-id Assign a cluster ID to a BGP cluster with more than one route reflector.
PAGE 357
cluster-id command. Without a cluster ID, the route reflector cannot recognize route updates from the other route reflectors within the cluster. The default format for displaying the cluster-id is dotted decimal, but if you enter the cluster-id as an integer, it is displayed as an integer. This command automatically restarts the BGP instance for the configuration to take effect. Related Commands bgp client-to-client reflection — enables route reflection between the route reflector and clients.
PAGE 358
Usage Information To accept 4-byte formats before entering a 4-byte AS number, configure your system. All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors. Each autonomous system is fully meshed and contains a few connections to other autonomous systems. The next hop, MED, and local preference information is preserved throughout the confederation.
PAGE 359
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added support for the 4-byte format. All the routers in the Confederation must be 4 byte or 2 byte identified routers. You cannot mix them. The autonomous systems configured in this command are visible to the EBGP neighbors.
PAGE 360
bgp dampening Enable BGP route dampening and configure the dampening parameters. Syntax bgp dampening [half-life reuse suppress max-suppress-time] [route-map mapname] To disable route dampening, use the no bgp dampening [half-life reuse suppress maxsuppress-time] [route-map map-name] command. Parameters half-life (OPTIONAL) Enter the number of minutes after which the Penalty is decreased.
PAGE 361
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. If you enter the bgp dampening command, the default values for half-life, reuse, suppress, and max-suppress-time are applied. The parameters are position-dependent; therefore, if you configure one parameter, configure the parameters in the order they appear in the CLI.
PAGE 362
Usage Information All routers apply the bgp default local-preference command setting within the AS. To set the local preference for a specific route, use the set local-preference command in ROUTE-MAP mode. Related Commands set local-preference — assigns a local preference value for a specific route. bgp dmzlink-bw Enables BGP Link Bandwidth. Syntax bgp dmzlink-bw To disable BGP Link Bandwidth, enter the no bgp dmzlink-bw command.
PAGE 363
Defaults Enabled Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 364
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 365
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Routers supporting 4-byte ASNs advertise that function in the OPEN message. The behavior of a 4-byte router is slightly different depending on whether it is speaking to a 2-byte router or a 4-byte router.
PAGE 366
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. This feature is advertised to BGP neighbors through a capability advertisement.
PAGE 367
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In Non-Deterministic mode, paths are compared in the order in which they arrive. This method can lead to Dell Networking OS choosing different best paths from a set of paths, depending on the order in which they are received from the neighbors because MED may or may not get compared between adjacent paths.
PAGE 368
Usage Information This command is a knob to disable BGP next-hop resolution using BGP learned routes. During the next-hop resolution, only the first route that the next-hop resolves through is verified for the route’s protocol source and is checked if the route is learned from BGP or not. The clear ip bgp command is required for this command to take effect and to keep the BGP database consistent. Execute the clear ip bgp command right after executing this command.
PAGE 369
databases. The Regex Engine Performance Enhancement feature optimizes the CPU usage by caching and reusing regular expression evaluation results. This caching and reuse may be at the expensive of RP1 processor memory. Examples Dell(conf-router_bgp)#no bgp regex-eval-optz-disable Dell(conf-router_bgp)#do show ip protocols Routing Protocol is "ospf 22222" Router ID is 2.2.2.2 Area Routing for Networks 51 10.10.10.0/00 Routing Protocol is "bgp 1" Cluster Id is set to 10.10.10.0 Router Id is set to 10.10.10.
PAGE 370
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Peering sessions are reset when you change the router ID of a BGP router. This command automatically restarts the BGP instance for the configuration to take effect. clear ip bgp Reset BGP sessions. The soft parameter (BGP Soft Reconfiguration) clears the policies without resetting the TCP connection.
PAGE 371
peer-group Enter the peer-group to clear all members of the peer-group. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 372
ipv6–address mask (OPTIONAL) Enter the IPv6 address and the network mask to clear information on IPv6 route dampening. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 373
ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to clear information related only to ipv6 unicast routes. ipv4-address mask (OPTIONAL) Enter an IPv4 address in dotted decimal format and the prefix mask in slash format (/x) to reset only that prefix. ipv6–address mask (OPTIONAL) Enter the IPv6 address followed by the network mask to reset only that prefix. filter-list as-pathname (OPTIONAL) Enter the keywords filter-list then the name of a configured AS-PATH list.
PAGE 374
Usage Information If you enter the clear ip bgp flap-statistics command without any parameters, all statistics are cleared. Related Commands show debugging — views the enabled debugging operations. show ip bgp flap-statistics — views the BGP flap statistics. undebug all — disables all debugging operations. clear ip bgp peer-group Reset a peer-group’s BGP sessions.
PAGE 375
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. deny bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to deny incoming or outgoing traffic. Syntax deny bandwidth To disable this setting, enter the no deny bandwidth command.
PAGE 376
in (OPTIONAL) Enter the keyword in to view only information on inbound BGP routes. out (OPTIONAL) Enter the keyword out to view only information on outbound BGP routes. A.B.C.D Enter the IP address of peer in the A.B.C.D format. X:X:X:X::X Enter the IPv6 IP address of peer in the X:X:X:X::X format. dampening Enter the keyword dampening to view BGP dampening. events Enter the keyword events to view BGP protocol events. ipv4 Enter the ipv4 IP address to view the IPV4 route information.
PAGE 377
debug ip bgp notifications — views information about BGP notifications. debug ip bgp updates — views information about BGP updates. show debugging — views enabled debugging operations. debug ip bgp dampening View information on routes being dampened. Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command.
PAGE 378
debug ip bgp events Display information on local BGP state changes and other BGP events. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] events [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] events [in | out] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP state changes corresponding to that VRF. A.B.C.
PAGE 379
debug ip bgp keepalives Display information about BGP keepalive messages. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] keepalives [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] keepalives [in | out] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display BGP keepalive information corresponding to that VRF. A.B.C.
PAGE 380
debug ip bgp notifications Allows you to view information about BGP notifications received from neighbors. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] notifications [in | out] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] notifications [in | out] command.
PAGE 381
debug ip bgp soft-reconfiguration Enable soft-reconfiguration debug. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group-name] softreconfiguration To disable, use the debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peergroup-name] soft-reconfiguration command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable soft-reconfiguration debugging on that VRF. A.B.C.
PAGE 382
debug ip bgp updates Allows you to view information about BGP updates. Syntax debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-groupname] updates [in | out | prefix-list prefix-list-name] To disable debugging, use the no debug ip bgp [vrf vrf-name] [A.B.C.D | X:X:X:X::X | peer-group peer-group-name] updates [in | out | prefix-list prefix-listname] command.
PAGE 383
Usage Information Version Description 7.7.1.0 Introduced on the C-Series. To remove all configured debug commands for BGP, enter the no debug ip bgp command. default-metric Allows you to change the metric of redistributed routes to locally originated routes. Use this command with the redistribute command. Syntax default-metric number To return to the default setting, use the no default-metric command. Parameters number Enter a number as the metric to be assigned to routes from other protocols.
PAGE 384
description Enter a description of the BGP routing protocol Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the BGP protocol (80 characters maximum). Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 385
number Enter a number as the maximum number of parallel paths. The range is from 2 to 64. Defaults none Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 386
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 387
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 388
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. neighbor advertisement-start To send BGP routing updates, set the minimum interval before starting.
PAGE 389
neighbor allowas-in Set the number of times an AS number can occur in the AS path. Syntax neighbor {ip-address | peer-group-name} allowas-in number To return to the default value, use the no neighbor {ip-address | peer-group-name} allowas-in command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the advertisement interval for all routers in the peer group.
PAGE 390
neighbor default-originate Inject the default route to a BGP peer or neighbor. Syntax neighbor {ip-address | peer-group-name} default-originate [route-map mapname] To remove a default route, use the no neighbor {ip-address | peer-group-name} defaultoriginate command. Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the default route of all routers in that peer group.
PAGE 391
When you apply a default route to a BGP peer or peer group using the neighbor default-originate command, changes to the configured default route-map are applied to the BGP peer or peer group only after a delay of 15 seconds. As a result, you must wait for a period of 15 seconds before manually resetting BGP using the clear ip bgp command. In case of eBGP, the neighbor default-originate command does not support extendedcommunity as a non-transtive route-map attribute.
PAGE 392
Version Description 7.7.1.0 Introduced on the C-Series. neighbor distribute-list Distribute BGP information via an established prefix list. Syntax neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} To delete a neighbor distribution list, use the no neighbor {ip-address | peer-group-name} distribute-list prefix-list-name {in | out} command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 393
Related Commands neighbor route-map — assigns a route map to a neighbor or peer group. neighbor ebgp-multihop Attempt and accept BGP connections to external peers on networks that are not directly connected. Syntax neighbor {ip-address | peer-group-name} ebgp-multihop [ttl] To disallow and disconnect connections, use the no neighbor {ip-address | peer-groupname} ebgp-multihop command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format.
PAGE 394
neighbor fall-over Enable or disable fast fall-over for BGP neighbors. Syntax neighbor {ipv4-address | peer-group-name} fall-over To disable, use the no neighbor {ipv4-address | peer-group-name} fall-over command. Parameters ipv4-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group. Defaults Disabled. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 395
To return to the default value, use the no neighbor {ip-address | peer-group-name} local-as command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to set the advertisement interval for all routers in the peer group. as-number Enter the AS number to reset all neighbors belonging to that AS. The range is from 0 to 65535 (2 byte), from 1 to 4294967295 (4 byte) or from 0.1 to 65535.65535 (dotted format).
PAGE 396
To return to the default values, use the no neighbor {ip-address | peer-group-name} maximum-prefix maximum command. Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group. maximum Enter a number as the maximum number of prefixes allowed for this BGP router. The range is from 1 to 4294967295. threshold (OPTIONAL) Enter a number to be used as a percentage of the maximum value.
PAGE 397
Related Commands show ip bgp summary — displays the current BGP configuration. neighbor password Enable message digest 5 (MD5) authentication on the TCP connection between two neighbors. Syntax neighbor {ip-address | peer-group-name} password [encryption-type] password To delete a password, use the no neighbor {ip-address | peer-group-name} password command. Parameters ip-address Enter the IP address of the router to be included in the peer group.
PAGE 398
Configure the same password on both BGP peers or a connection does not occur. When you configure MD5 authentication between two BGP peers, each segment of the TCP connection between them is verified and the MD5 digest is checked on every segment sent on the TCP connection. Configuring a password for a neighbor causes an existing session to be torn down and a new one established.
PAGE 399
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the dmzlink-bw parameter. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. You can assign up to 256 peers to one peer group.
PAGE 400
Parameters peer-group-name Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 401
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 402
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 403
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 404
NOTE: This command sends routes to peers only if an outbound policy is configured and if there is a change in the existing outbound policy. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 405
Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 406
peer-group-name Enter the name of the peer group to enable or disable all routers with in the peer group. All routers in the peer group receive routes from a route reflector. Defaults Enabled. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 407
standard (OPTIONAL) Enter the keyword standard to send standard community attribute. Defaults Not configured and COMMUNITY attributes are not sent to neighbors. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 408
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 409
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 410
Defaults keepalive Enter a number for the time interval, in seconds, between keepalive messages sent to the neighbor routers. The range is from 1 to 65535. The default is 60 seconds. holdtime Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The default is 180 seconds. • keepalive = 60 seconds • holdtime = 180 seconds Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 411
Parameters ip-address Enter the IP address of the peer router in dotted decimal format. peer-group-name Enter the name of the peer group to disable all routers within the peer group. interface Enter the keyword loopback then a number of the Loopback interface. The range is from 0 to 16383. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 412
Defaults 0 Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 413
route-map mapname (OPTIONAL) Enter the keyword route-map then the name of an established route map. Only the following ROUTE-MAP mode commands are supported: • match ip address • set community • set local-preference • set metric • set next-hop • set origin • set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific.
PAGE 414
It is possible to keep only one locally originated route in the BGP database. Network command has preference over the re-distributed routes. When the locally originated route is no longer present in the database the other route is automatically installed. In BGP, the next-hop for the route is calculated from the information that is acquired through IGP or static routes. Related Commands redistribute — redistributes routes into BGP. network backdoor Specify this IGP route as the preferred route.
PAGE 415
permit bandwidth Enables you to specify link band width extended-community attribute as the matching criteria to permit incoming or outgoing traffic. Syntax permit bandwidth To disable this setting, enter the no permit bandwidth command. Parameters bandwidth Enter the keyword bandwidth to specify extended-community attribute as the matching criteria for permitting traffic. The range is from 0 to 102400.
PAGE 416
• set weight If the route map is not configured, the default is deny (to drop all routes). Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 417
redistribute ospf Redistribute OSPF routes into BGP. Syntax redistribute ospf process-id [[match external {1 | 2}] [match internal]] [route-map map-name] To stop redistribution of OSPF routes, use the no redistribute ospf process-id command. Parameters process-id Enter the number of the OSPF process. The range is from 1 to 65535. match external {1 | 2} (OPTIONAL) Enter the keywords match external to redistribute OSPF external routes. You can specify 1 or 2 to redistribute those routes only.
PAGE 418
When you enter the redistribute isis process-id command without any other parameters, Dell Networking OS redistributes all OSPF internal routes, external type 1 routes, and external type 2 routes. RFC does not support this feature. router bgp To configure and enable BGP, enter ROUTER BGP mode. Syntax router bgp as-number To disable BGP, use the no router bgp as-number command. Parameters as-number Enter the AS number. The range is from 1 to 65535 (2 byte), from 1 to 4294967295 (4 byte), or from 0.
PAGE 419
set extcommunity bandwidth Enables you to set extended community bandwidth. Syntax set extcommunity bandwidth To disable extended community bandwidth, enter the no set extcommunity bandwidth command. Parameters bandwidth Defaults N/A Command Modes ROUTER MAP Command History Usage Information Enter the keyword bandwidth to enable extended community bandwidth. The range is from 0 to 102400. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 420
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced. Dell(conf-router_bgp)#show capture bgp-pdu neighbor 20.20.20.2 Incoming packet capture enabled for BGP neighbor 20.20.20.
PAGE 421
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Dell(conf-router_bgp)#show config ! router bgp 100 network 1.1.11.1/32 network 1.1.12.1/32 network 1.1.13.1/32 neighbor 10.1.1.
PAGE 422
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Added the add-path option to the S4810. Output on the S4810 shows the ADDPATH parameters. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series.
PAGE 423
All the show and debugs commands display the link band width extended-community prefixed with DMZLink-bw along with other extended communities. Dell#show ip bgp 3.3.3.0/24 BGP routing table entry for 3.3.3.0/24 Paths: (1 available, table Default-IP-Routing-Table.) Not advertised to any peer Received from : 1.1.1.2 (3.3.3.1) Best AS_PATH : Next-Hop : 1.1.1.
PAGE 424
Usage Information Example Version Description 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp cluster-list command shown in the following example.
PAGE 425
show ip bgp community View information on all routes with Community attributes or view specific BGP community groups. Syntax Parameters show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] community [community-number] [local-as] [no-export] [no-advertise] vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view information either on all routes with community attributes or specific BGP community routes corresponding to that VRF.
PAGE 426
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.
PAGE 427
*> *> 55.0.0.0/24 66.0.0.0/24 172.16.0.2 172.16.0.2 0 200 i 0 200 i Dell#show ip bgp community no-advertise BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete *> Network 66.0.0.0/24 Next Hop 172.16.0.
PAGE 428
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The show ip bgp community-list command without any parameters lists BGP routes matching the Community List and the output is the same as for the show ip bgp command output.
PAGE 429
Communities : 200:1 1000:1 3000:1 show ip bgp dampened-paths View BGP routes that are dampened (non-active). Syntax Parameters Command Modes Command History show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] dampened-paths vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF.
PAGE 430
The history paths that the show ip bgp command displays contain only the prefix and the next-hop information. The next-hop information shows the ip address of the neighbor. It does not show the actual next-hop details. The following describes the show ip bgp damp command shown in the following example. Example Field Description Network Displays the network ID to which the route is dampened. From Displays the IP address of the neighbor advertising the dampened route.
PAGE 431
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced.
PAGE 432
Address Family specific Information AFIndex 0 NdSpFlag 0x41a190b0 : AFRttP 0x41a0d200 : NdRTMMkrP 0x41a19d28 : NdRTMAFTblVer 0 : NdRibCtxAddr 1101110688 NdRibCtxAddrLen 255 : NdAFPrefix 0 : NdAfNLRIP 0 : NdAFNLRILen 0 : NdAFWPtrP 0 NdAFWLen 0 : NdAfNH : NdAFRedRttP 0x41a0d400 : NdRecCtxAdd 1101110868 NdRedCtxAddrLen 255 : NdAfRedMkrP 0x41a19e88 : AFAggRttP 0x41a0d600 : AfAggCtxAddr 1101111028 : AfAggrCtxAddrLen 255 AfNumAggrPfx 0 : AfNumAggrASSet 0 : AfNumSuppmap 0 : AfNumAggrValidPfx 0 : AfMPathRttP 0x41a0
PAGE 433
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. To view the total number of COMMUNITY attributes found, use the show ip bgp summary command.
PAGE 434
Command Modes Command History ipv4 unicast (OPTIONAL) Enter the keyword ipv4 followed by the keyword unicast to view information related only to ipv4 unicast routes. ipv6 unicast (OPTIONAL) Enter the keyword ipv6 followed by the keyword unicast to view information related only to ipv6 unicast routes. as-path-name Enter an AS-PATH access list name. The range is 140 characters. • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 435
Example Field Description Path Lists all the ASs the route passed through to reach the destination network. Dell#show run as-path a1 ! ip as-path access-list a1 permit 500 Dell# Dell#show ip bgp filter-list a1 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.
PAGE 436
NOTE: Enter an escape sequence (CTRL+v) prior to entering the ? regular expression. Command Modes Command History • EXEC • EXEC Privilege • [ ] = (brackets) a range of single-character patterns. • ( ) = (parenthesis) groups a series of pattern elements to a single element. • { } = (braces) minimum and the maximum match count. • ^ = (caret) the beginning of the input string. If you use the caret at the beginning of a sequence or range, it matches on everything BUT the characters specified.
PAGE 437
Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path source: I - internal, a - aggregate, c - confed-external, r redistributed n - network, D - denied, S - stale Origin codes: i - IGP, e - EGP, ? - incomplete Network From Reuse Path h 77.0.0.0/24 172.16.0.2 00:00:00 d 55.0.0.0/24 172.16.0.2 00:30:44 200 i *> 66.0.0.0/24 172.16.0.2 00:00:00 200 i Dell#*>n 66.66.77.77/32 0.0.0.
PAGE 438
Usage Information Example The following describes the show ip bgp inconsistent-as command shown in the following example. Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight.
PAGE 439
*>n 66.66.66.77/32 *>n 66.66.77.77/32 0.0.0.0 0.0.0.0 0 0 32768 i 32768 i show ip bgp neighbors Allows you to view the information BGP neighbors exchange.
PAGE 440
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added the ipv4 multicast and ipv6 unicast parameters. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 441
The Lines Beginning with: Example Description • last read is the time (hours:minutes:seconds) the router read a message from its neighbor • hold time is the number of seconds configured between messages from its neighbor • keepalive interval is the number of seconds between keepalive messages to help ensure that the TCP session is still alive.
PAGE 442
Capabilities received from neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) ADD_PATH(69) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 InQ : Added 0, Replaced 0, Withdrawn 0 OutQ : Added 0, Withdrawn 0 Allow local AS number 0 times in AS-PATH attribute Prefixes accepted 2, withdrawn 15 by peer, martian prefixes ignored 0 Prefixes
PAGE 443
Usage Information Example Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp next-hop command shown in the following example. Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop. RefCount Displays the number of BGP routes using this next hop.
PAGE 444
• Command Modes Command History • EXEC • EXEC Privilege $ = (dollar sign) the end of the output string. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 445
1 1 0 0 200 i 200 i show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. Syntax Command Modes Command History show ip bgp [vrf vrf-name] paths community • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.8(0.
PAGE 446
show ip bgp peer-group Allows you to view information on the BGP peers in a peer group. Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] peer-group [peer-group-name [detail | summary]] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf to view information on BGP peers in a peer group corresponding to that VRF. NOTE: You can use this attribute to view information on BGP peers in a peer group that correspond to either a default or a non-default VRF.
PAGE 447
Usage Information Example Version Description 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. The following describes the show ip bgp peer-group command shown in the following example. Line beginning with: Description Peer-group Displays the peer group’s name. Administratively shut Displays the peer group’s status if the peer group is not enabled. If you enable the peer group, this line is not displayed. BGP version Displays the BGP version supported.
PAGE 448
NOTE: You can use this attribute to view the subset of BGP routing tables that match the regular expression that is specified on either a default or a non-default VRF. regular-expression [character] Enter a regular expression then use one or a combination of the following characters to match: • . = (period) any single character (including a white space). • * = (asterisk) the sequences in a pattern (zero or more sequences). • + = (plus) the sequences in a pattern (one or more sequences).
PAGE 449
Example Field Description Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then non-BGP routes exist in the router’s routing table. Metric Displays the BGP router’s metric, if assigned. LocPrf Displays the BGP LOCAL_PREF attribute for the route. Weight Displays the route’s weight Path Lists all the AS paths the route passed through to reach the destination network.
PAGE 450
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. In BGP, route attributes are maintained at different locations.
PAGE 451
Field Description MsgRcvd Displays the number of BGP messages that neighbor received. MsgSent Displays the number of BGP messages that neighbor sent. TblVer Displays the version of the BGP table that was sent to that neighbor. InQ Displays the number of messages from that neighbor waiting to be processed. OutQ Displays the number of messages waiting to be sent to that neighbor. If a number appears in parentheses, the number represents the number of messages waiting to be sent to the peer group.
PAGE 452
show running-config bgp To display the current BGP configuration, use this feature. Syntax show running-config bgp Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 453
Parameters keepalive Enter a number for the time interval, in seconds, between keepalive messages sent to the neighbor routers. The range is from 1 to 65535. The default is 60 seconds. holdtime Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The default is 180 seconds. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 454
debug ip bgp dampening View information on routes being dampened. Syntax debug ip bgp [vrf vrf-name] [ipv4 {unicast | multicast} | ipv6 unicast] dampening To disable debugging, use the no debug ip bgp dampening command. Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to view information on dampened routes corresponding to that VRF.
PAGE 455
distance bgp Configure three administrative distances for routes. Syntax distance bgp external-distance internal-distance local-distance To return to default values, use the no distance bgp command. Parameters Defaults external-distance Enter a number to assign to routes learned from a neighbor external to the AS. The range is from 1 to 255. The default is 20. internal-distance Enter a number to assign to routes learned from a router within the AS. The range is from 1 to 255. The default is 200.
PAGE 456
show ip bgp dampened-paths View BGP routes that are dampened (non-active). Syntax show ip bgp [vrf vrf-name] [ipv4 {multicast | unicast} | ipv6 unicast] dampened-paths Parameters Command Modes Command History vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes that are affected by a specific community list corresponding to that VRF.
PAGE 457
The following describes the show ip bgp damp command shown in the following example. Example Field Description Network Displays the network ID to which the route is dampened. From Displays the IP address of the neighbor advertising the dampened route. Reuse Displays the hour:minutes:seconds until the dampened route is available. Path Lists all the ASs the dampened route passed through to reach the destination network.
PAGE 458
additive (OPTIONAL) Enter the keyword additive to add to the existing extended community. non-trans (OPTIONAL) Enter the keywords non-trans to indicate a non-transitive BGP extended community. Defaults none Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 459
IPADDR:NN Enter the IP address specific extended community in the format IPADDR:NN (4byte IPv4 Unicast Address:2-byte community value). non-trans (OPTIONAL) Enter the keywords non-trans to indicate a non-transitive BGP extended community. Defaults none Command Modes ROUTE MAP (config-route-map) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 460
The following is a list of the Dell Networking OS version history for this command. Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series.
PAGE 461
The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series.
PAGE 462
NOTE: If you enter soft, without an in or out option, both inbound and outbound policies are reset. out Reapply only outbound policies. NOTE: If you enter soft, without an in or out option, both inbound and outbound policies are reset. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 463
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Added support for IPv4 multicast and IPv6 unicast routes. 7.8.1.0 Introduced on the S4810. 7.7.1.0 Introduced on the C-Series. 7.2.1.0 Introduced on the E-Series TeraScale.
PAGE 464
neighbor soft-reconfiguration inbound Enable a BGP soft-reconfiguration and start storing updates for inbound IPv6 unicast routes. Syntax neighbor {ipv4-address | ipv6-address | peer-group-name} softreconfiguration inbound Parameters ipv4-address | ipv6address Enter the IP address of the neighbor for which you want to start storing inbound routing updates. peer-group-name Enter the name of the peer group for which you want to start storing inbound routing updates. Defaults Disabled.
PAGE 465
NOTE: There is a 140-character limit for prefix list names. summary Display a summary of RPF routes. Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant FTOS Command Line Reference Guide. The following is a list of the FTOS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.0.0.0 Introduced on the Z9000. 8.3.
PAGE 466
Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810.
PAGE 467
11 Content Addressable Memory (CAM) You can use Content Addressable Memory (CAM) commands to configure the amount of memory allocated to CAM memory partitions. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the first time, contact Dell Networking Technical Assistance Center (TAC) for guidance.
PAGE 468
• Configure more Layer 2 forwarding information base (FIB) entries when the system is deployed as a switch. • Configure more Layer 3 FIB entries when the system is deployed as a router. • Configure more access control lists (ACLs) (when IPv6 is not employed). • Hash multi-protocol label switching (MPLS) packets based on source and destination IP addresses for link aggregation groups (LAGs). • Hash based on bidirectional flow for LAGs.
PAGE 469
• vrfv4Acl :0 • Openflow : 0 • fedgovacl : 0 l2acl number Enter the keyword l2acl and then the number of l2acl blocks. The range is from 1 to 8. ipv4acl number Enter the keyword ipv4acl and then the number of FP blocks for IPv4. The range is from 0 to 8. ipv6acl number Enter the keyword ipv6acl and then the number of FP blocks for IPv6. The range is from 0 to 4. ipv4qos number Enter the keyword ipv4qos and then the number of FP blocks for IPv4. The range is from 0 to 8.
PAGE 470
ipv6acl number, ipv4qos number l2qos numberl2pt number ipmacacl number ecfmacl number {nlbclusteracl] [vman-qos | vmandual-qos number] ipv4pbr numberopenflow {4|8} | fcoe number [iscsioptacl number] [vrfv4acl number] Enter 4 or 8 for the number of OpenFlow FP blocks.
PAGE 471
If you enable BMP, to perform a reload on the chassis to upgrade any configuration changes that have changed the NVRAM content, use the command reload conditional nvram-cfg-change. cam-acl-egress Allocate CAM for egress ACLs. Syntax Parameters cam-acl-egress default | l2acl number ipv4acl number ipv6acl number default Reset egress CAM ACL entries to default settings. l2acl number Allocate space to each CAM region. The total space allocated must equal 4. The ipv6acl range must be a factor of 2.
PAGE 472
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0. Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 473
Version Description 7.8.1.0 Introduced on the C-Series. Usage Information The display reflects the settings implemented with the cam-acl command.
PAGE 474
test cam-usage Verify that enough CAM space is available for the IPv6 ACLs you have created. Syntax test cam-usage service-policy input input policy name stack-unit {number | all} Parameters policy-map name Enter the name of the policy-map to verify. Maximum is 32 characters. number Enter all to get information for all the linecards/stack-units or enter the linecard/ stack-unit number to get information for a specific card. The range is 0-7 for all other S-Series. The range is 1-6.
PAGE 475
Term Explanation Portpipe Lists the portpipe (port-set) or port pipes (port-sets) that are checked. Entering all shows the status for linecards or stack units and port-pipes in the chassis. The port set value is from 0 to 0. CAM Partition Shows the CAM profile of the CAM. Available CAM Identifies the amount of CAM space remaining for that profile. Estimated CAM per Port Estimates the amount of CAM space the listed policy will require.
PAGE 476
12 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. The CoPP filters prevent traffic that is not identified as legitimate from reaching the control plane, and rate-limit traffic to an acceptable level.
PAGE 477
service-policy rate-limit-cpu-queues Apply a policy map for the system to rate limit control traffic on a per-queue basis. Syntax Parameters service-policy rate-limit-cpu-queues policy-name policy-name Enter the service-policy name, using a string up to 32 characters. Defaults Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 478
Defaults Not configured. Command Modes CONTROL-PLANE-CPUQOS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000.
PAGE 479
Parameters Command Modes Command History Usage Information vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to enable catch-all routes corresponding to that VRF. CONFIGURATION Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Introduced on the S–Series. Use this command to add the IPv4 catch-all route (0.0.0.
PAGE 480
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 481
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 482
The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 483
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810.
PAGE 484
13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell Networking OS. Diagnostics and Monitoring Commands The following section describes the diagnostics and monitoring commands. For similar commands, refer to the Control and Monitoring chapter. logging coredump stack-unit Enable coredump on a stack. Syntax logging coredump stack-unit {stack-unit-number | all} Parameters stack-unit stackunit-number Enter the stack-unit id. The range is from 1 to 6.
PAGE 485
Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and standby. Important Points to Remember • Offline diagnostics can only be run when the unit is offline. • You can only run offline diagnostics on a unit to which you are connected via the console.
PAGE 486
no-reboot Enter the keyword no-reboot to prevent the system from rebooting after the test. To bring the stack unit to online state, use the online stack-unit command. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 487
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added a warning message to the off-line diagnostic. 7.7.1.0 Introduced on the S-Series. You cannot enter this command on a Master or Standby unit. The system reboots when the off-line diagnostics complete. This reboot is an automatic process. A warning message appears when the offline stack-unit command is implemented.
PAGE 488
The system reboots when the off-line diagnostics complete. This reboot is an automatic process. A warning message appears when the offline stack-unit command is implemented. Warning - Diagnostic execution will cause stack-unit to reboot after completion of diags. Proceed with Offline-Diags [confirm yes/no]:y Hardware Commands These commands display information from a hardware sub-component or ASIC. clear hardware stack-unit Clear statistics from selected hardware components.
PAGE 489
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. show hardware stack-unit — displays the data plane or management plane input and output statistics of the designated component of the designated stack member. clear hardware system-flow Clear system-flow statistics from selected hardware components.
PAGE 490
Parameters vlan-id Enter the interface VLAN number. The range is from 1 to 4094. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 491
show hardware layer2 Display Layer 2 ACL or eg data for the selected stack member and stack member port-pipe. Syntax Parameters show hardware layer2 {eg-acl | in-acl} stack-unit id port-set 0–0 eg-acl | in-acl Enter either the keyword eg-acl or the keyword in-acl to select between ingress or egress ACL data. stack-unit id Enter the keyword stack-unit to select a stack ID. The range is from 1 to 6. port-set 0–0 Enter the keywords port-set with a port-pipe number. . The range is from 0 to 0.
PAGE 492
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.
PAGE 493
Defaults Command Modes Command History cpu sata-interface statistics Enter the keywords cpu sata-interface statistics to display the sata interface error counter statistics. drops [unit unitnumber] Enter the keyword drops to display internal drops on the selected stack member. Enter the drops keyword to display internal drops on the selected stack member. fpga register Enter the keyword to display the register value of fpga resgister details in S4810, Z9000 and S6000.
PAGE 494
9 64-byte pkts, 310 over 64-byte pkts, 1 over 127-byte pkts 1 over 255-byte pkts, 2 over 511-byte pkts, 2 over 1023-byte pkts 0 Multicasts, 3 Broadcasts, 322 Unicasts 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec Output 00.
PAGE 495
Example (Register) Dell#show hardware stack-unit 1 unit 1 register 0x0068003c AGINGCTRMEMDEBUG.mmu0 = 0x00000000 0x0068003d AGINGEXPMEMDEBUG.mmu0 = 0x00000000 0x00680017 ASFCONFIG.mmu0 = 0x0000000e 0x0060004c ASFPORTSPEED.ge0 = 0x00000000 0x0060104c ASFPORTSPEED.ge1 = 0x00000000 0x0060204c ASFPORTSPEED.ge2 = 0x00000000 0x0060304c ASFPORTSPEED.ge3 = 0x00000000 0x0060404c ASFPORTSPEED.ge4 = 0x00000000 0x0060504c ASFPORTSPEED.ge5 = 0x00000000 0x0060604c ASFPORTSPEED.ge6 = 0x00000000 0x0060704c ASFPORTSPEED.
PAGE 496
0x0b706001 BCAST_STORM_CONTROL.ge6 = 0x00000000 0x0b707001 BCAST_STORM_CONTROL.ge7 = 0x00000000 0x0b708001 BCAST_STORM_CONTROL.ge8 = 0x00000000 0x0b709001 BCAST_STORM_CONTROL.ge9 = 0x00000000 0x0b70a001 BCAST_STORM_CONTROL.
PAGE 497
TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - 2048 to 4095 Byte Frame Counter 4096 to 9216 Byte Frame Counter Good Packet Counter Packet/Frame Counter Unicast Frame Counter Multicast Frame Counter Broadcast Frame Counter Byte Counter Control Frame Counter Pause Control Frame Counter Oversized Frame Counter Jabber Counter VLAN Tag Frame Counter Double VLAN Tag Frame Counter RUNT Frame Counter Fragment Counter PFC Frame Priority 0 PFC Frame Pri
PAGE 498
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX 498 - Jabber Frame Counter VLAN Tag Frame Counter Double VLAN Tag Frame Counter RUNT Frame Counter Fragment Counter VLAN Tagged Packets Ingress Dropped Packet MTU Check Error Frame Counter PFC Frame Priority 0 PFC Frame Priority 1 PFC Frame Priority 2 PFC Frame Priority 3 PFC Frame Priority 4 PFC Frame Prio
PAGE 499
TX - Debug Counter 10 TX - Debug Counter 11 Example (Details) 0 0 Dell#show hardware stack-unit 1 unit 1 details ****************************************************** The total no of FP & CSF Devices in the Card is 2 The total no of FP Devices in the Card is 2 The total no of CSF Devices in the Card is 0 The number of ports in device 0 is - 24 The number of Hg ports in devices 0 is - 4 The CPU Port of the device is 28 The number of ports in device 1 is - 24 The number of Hg ports in devices 1 is - 4 The
PAGE 500
================================ ----- Buffer Stats for Interface Gi 1/0 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/1 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/2 Queue Maximum Shared Limit: 7667 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/3 Queue Maximum Sh
PAGE 501
EXEC Privilege Command History Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, Z9000, and Z9500.
PAGE 502
Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/1 Queue Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/1 Queue Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: Used Packet Buffer: 0 ----- Buffer Stats for Interface Gi 1/1 Queue Maximum Shared Limit: 29514 Default Packet Buffer allocate for the Queue: 9 ----8 10 ----8 11 ----8 show hardware counters int
PAGE 503
RX - 128 to 255 Byte Frame Counter RX - 256 to 511 Byte Frame Counter RX - 512 to 1023 Byte Frame Counter RX - 1024 to 1518 Byte Frame Counter RX - 1519 to 1522 Byte Good VLAN Frame Counter RX - 1519 to 2047 Byte Frame Counter RX - 2048 to 4095 Byte Frame Counter RX - 4096 to 9216 Byte Frame Counter RX - Good Packet Counter RX - Packet/Frame Counter RX - Unicast Frame Counter RX - Multicast Frame Counter RX - Broadcast Frame Counter RX - Byte Counter RX - Control Frame Counter RX - Pause Control Frame Count
PAGE 504
Command Modes EXEC EXEC Privilege Command History Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, Z9000, Z9500. -Queue ucast/mcast — Displays the total unicast/multicast buffer usage on per-port per-queue basis. For CPU port, counters for queues 0 to 11 displays and there is no differentiation between unicast and multicast queues.
PAGE 505
Command Modes • All - Displays ingress and egress device, port, and queue snapshots • Interface all queue {all} - egress queue-level snapshot for both unicast and multicast packets • Interface all queue ucast {id | all} - egress queue-level snapshot for unicast packets only • Interface all queue mcast {id | all} - egress queue-level snapshot for multicast packets only • Interface all prio-group {id | all} - ingress priority-group level snapshot EXEC EXEC Privilege Command History Usage Informat
PAGE 506
Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 17 (interface Fo 1/160) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 21 (interface Fo 1/164) --------------------------------------Q# TYPE Q# TOTAL BUFFERED CELLS --------------------------------------MCAST 3 0 Unit 1 unit: 3 port: 25 (interface Fo 1/168) --------------------------------------Q# TYPE Q# TOTAL BUFFER
PAGE 507
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 508
KEY=0x00000000 00000000 00000000 0180c200 00020000 00000000 00000000 , FPF4=0x00 MASK=0x00000000 00000000 00000000 ffffffff ffff0000 00000000 00000000 , 0x00 action={act=Drop, param0=0(0x00), param1=0(0x00)}, action={act=CosQCpuNew, param0=7(0x07), param1=0(0x00)}, action={act=CopyToCpu, param0=0(0x00), param1=0(0x00)}, action={act=UpdateCounter, param0=1(0x01), param1=0(0x00)}, meter=NULL, counter={idx=2, mode=0x01, entries=1} ################# FP Entry for redirecting GVRP traffic to RSM ########### EID 2
PAGE 509
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.7(0.0) Introduced this command. Example Dell#show hardware vlan-counters 1 Counters for vlanid: 1 -----------------------Total number of inpackets: 0 Total number of inbytes: 0 Total number of outpackets: 0 Total number of outbytes: 0 Dell# Related Commands clear hardware system-flow — clears the statistics from selected hardware components.
PAGE 510
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.5 Added i2c statistics and sata-interfaces statistics. 8.3.11.4 Added user port information. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series.
PAGE 511
Unknown Opcodes Internal Mac Receive Errors : 0 : 0 Debugging and Diagnostics 511
PAGE 512
14 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine. Commands to Configure the System to be a DHCP Server To configure the system to be a DHCP server, use the following commands. clear ip dhcp Reset the DHCP counters.
PAGE 513
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. Entering after the clear ip dhcp binding command clears all the IPs from the binding table. debug ip dhcp server Display FTOS debugging messages for DHCP. Syntax Parameters debug ip dhcp server [events | packets] events Enter the keyword events to display the DHCP state changes. packet Enter the keyword packet to display packet transmission/reception.
PAGE 514
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000 and Z-Series. default-router Assign a default gateway to clients based on the address pool. Syntax default-router address [address2...address8] Parameters address Enter a list of routers that may be the default gateway for clients on the subnet.
PAGE 515
Defaults Disabled Command Modes CONFIGURATION DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 516
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. domain-name Assign a domain to clients based on the address pool. Syntax domain-name name Parameters name Give a name to the group of addresses in a pool. Defaults none Command Modes DHCP Command History This guide is platform-specific.
PAGE 517
high-address Enter the highest address in a range of addresses to be excluded from the pool. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 518
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. host For manual (rather than automatic) configurations, assign a host to a single-address pool. Syntax host address Parameters address/mask Enter the host IP address and subnet mask. Defaults none Command Modes DHCP Command History This guide is platform-specific.
PAGE 519
infinite Specify that the lease never expires. Defaults 24 hours Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 520
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. netbios-node-type Specify the NetBIOS node type for a Microsoft DHCP client. Dell Networking recommends specifying clients as hybrid. Syntax netbios-node-type type Parameters type Enter the NETBIOS node type: • Broadcast: Enter the keyword b-node. • Hybrid: Enter the keyword h-node. • Mixed: Enter the keyword m-node.
PAGE 521
network Specify the range of addresses in an address pool. Syntax network network /prefix-length Parameters network/ prefixlength Specify a range of addresses. Prefix-length range is from 17 to 31. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 522
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp binding Display the DHCP binding table.
PAGE 523
global Display the DHCP configuration for the entire system. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 524
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 525
Commands to Configure Secure DHCP DHCP, as defined by RFC 2131, provides no authentication or security mechanisms. Secure DHCP is a suite of features that protects networks that use dynamic address allocation from spoofing and attacks. arp inspection Enable dynamic arp inspection (DAI) on a VLAN. Syntax arp inspection Defaults Disabled Command Modes INTERFACE VLAN Command History This guide is platform-specific.
PAGE 526
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series.
PAGE 527
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added the keywords discard-counters, interface, and the variable interface on the S4810, S4820T, S5000, S6000, Z9000, Z9500. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.
PAGE 528
Example Dell# clear ipv6 dhcp snooping? binding Clear the snooping binding database ip dhcp relay Enable Option 82. Syntax ip dhcp relay information-option [remote-id | trust-downstream] Parameters remote-id Configure the system to enable the remote-id string in option-82. trust-downstream Configure the system to trust Option 82 when it is received from the previous-hop router. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 529
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the S4810 and S4820T. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. 8.2.1.0 Introduced on the C-Series and S-Series on Layer 2 interfaces. 7.8.1.0 Introduced on the C-Series and S-Series on Layer 3 interfaces.
PAGE 530
To disable the ipv6 dhcp snooping on VLAN basis or range of VLAN, use the no ipv6 dhcp snooping vlan command. Parameters vlan-id Enter the name of a VLAN id or list of the VLANs to enable DHCP Snooping. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command-Line Reference Guide.
PAGE 531
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 532
Defaults none Command Modes Command History • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S6000, S6000-ON, and Z-Series.
PAGE 533
ipv6 dhcp snooping database write-delay To set time interval for storing the snooping binding entries in a file. Syntax [no] ipv6 dhcp snooping database write-delay value To disable the storing of snooping binding entries in a file, use the no ipv6 dhcp snooping writedelay command. Parameters value The range is from 5 to 21600. The value of the minutes range is from 5 min. to 15 days. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 534
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. ipv6 dhcp snooping database renew To load the binding entries from the file to DHCPv6 snooping binding database. Syntax ipv6 dhcp snooping database renew Defaults none Command Modes Command History • EXEC Privilege This guide is platform-specific.
PAGE 535
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on the C-Series and S-Series. ipv6 dhcp snooping trust Configure an interface as trusted for DHCP snooping. Syntax [no] ipv6 dhcp snooping trust To disable dhcp snooping trusted capability on this interface, use the no ipv6 dhcp snooping trust command.
PAGE 536
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6(0.0) Added the vlan keyword and the vlan-id variable . Introduced support for SAV on port channels interfaces. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 8.2.1.
PAGE 537
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the E-Series. 7.8.1.0 Introduced on C-Series and S-Series.
PAGE 538
ipv6 dhcp snooping verify mac-address Configure to enable verify source mac-address against ipv6 DHCP packet mac address. Syntax [no] ipv6 dhcp snooping verify mac-address To disable verify source mac-address against IPv6 DHCP packet MAC address, use the no ipv6 dhcp snooping verify mac-address command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 539
Usage Information Use this command on the interfaces where the DHCP clients are connected to forward the packets from clients to DHCP server and vice-versa. Example Dell(conf-if-gi-1/12)#ip helper-address vrf jay 10.0.0.2 ipv6 helper-address Configures the ipv6 DHCP helper addresses without VRF. Syntax [no] ipv6 helper-address ipv6-address To delete the ipv6 helper address, use the [no] ipv6 helper-address ipv6-address command.
PAGE 540
Parameters Description discard-counters (OPTIONAL) Display the number of dropped packets. interface interface (OPTIONAL) Specifies an interface to show the discard counters. Enter any of the following keywords and slot/port or number information: Defaults • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 541
Total cam count 4 permit host 0.0.0.0 permit vlan 10 host permit vlan 10 host permit vlan 20 host permit vlan 20 host host 00:00:00:00:00:00 count (0 10.1.1.1 host 00:00:00:aa:00:01 10.1.1.2 host 00:00:00:aa:00:02 10.2.2.1 host 00:00:00:aa:00:03 10.2.2.
PAGE 542
NOTE: The output for port-channel interfaces does not display the physical interface. If the LAG member interfaces belong to different stack-units, the counters are displayed per stack-unit for that port channel. show ipv6 dhcp snooping Display the DHCPv6 snooping binding database. Syntax show ipv6 dhcp snooping Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 543
To undo the name server ip address configuration for VRF, use the no ip name-server [vrf vrfname] ip-address command. Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to configure the name server IP addresses for that VRF. ip-address [ipaddress2] [ipaddress3] [ipaddress4] [ipaddress5] [ipaddress6] Enter the IP address of the name server in dotted decimal format.
PAGE 544
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4.(0.0) Introduced on the S-Series and Z-Series.
PAGE 545
Usage Information Use this command to add domain names to the DNS lists corresponding to a specific VRF. You can add up to a maximum of six domain names to the DNS list corresponding to a VRF. This domain is used to complete the unqualified host names. Example Dell(conf)#ip domain-list Dell(conf)#ip domain-list vrf jay dell.com vrf jay force10.com ip host Configures a mapping between the host name server and the IP address for a specific VRF.
PAGE 546
Parameters vrf vrf-name (Optional) Enter the key word vrf and then the name of the VRF to delete dynamically learned host table entries corresponding to that VRF. host-name Enter the name of the host corresponding to which you want to delete the dynamically learnt host table entries. * Enter * to delete all host table entries. Defaults None Command Modes EXEC Command History This guide is platform-specific.
PAGE 547
15 Equal Cost Multi-Path (ECMP) Equal cost multi-path (ECMP) supports multiple "best paths" in next-hop packet forwarding to a destination device. ecmp-group Provides a mechanism to monitor traffic distribution on an ECMP link bundle. A system log is generated when the standard deviation of traffic distribution on a member link exceeds a defined threshold. Syntax ecmp-group {ecmp-group-id interface interface | link-bundle-monitor} To remove the selected interface, use the ecmp-group no interface command.
PAGE 548
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. Using CONFIGURATION mode, create an ECMP group ID. You can then assign interfaces to the ECMP group using CONFIGURATION ECMP-GROUP mode. You can also enable on the port-channel configuration using the CONFIGURATION ECMP-GROUP command mode.
PAGE 549
hg {crc16 | crc16cc | crc32MSB | crc32LSB | xor1 | xor2 | xor4 | xor8 | xor16} stack-unit stack-unit-number | port-set port-pipe • xor4: Use CRC16_BISYNC_AND_XOR4 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor4 • xor8: Use CRC16_BISYNC_AND_XOR8 — Upper 8 bits of CRC16-BISYNC and lower 8 bits of xor8 • xor16: Use CR16 — 16 bit XOR Enter the keyword hg then one of the following options: • crc16: Use CRC16_BISYNC — 16 bit CRC16-bisync polynomial (default) • crc16cc: Use CRC16_CCITT — 16 bit C
PAGE 550
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.9(0.0) Added flow-based-hashing support for hashing on ECMP for S4820T, S6000, S4048 and Z9500. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 551
default algorithm does not provide a satisfactory distribution of traffic, use the hash-algorithm command to designate another algorithm. When a Port Channel member leaves or is added to the Port Channel, the hash algorithm is recalculated to balance traffic across the members. hash-algorithm ecmp Change the hash algorithm used to distribute traffic flows across an ECMP (equal-cost multipath routing) group.
PAGE 552
Term heading Description heading The different hash algorithms are based on the number of ECMP group members and packet values. The default hash algorithm yields the most balanced results in various test scenarios, but if the default algorithm does not provide satisfactory distribution of traffic, use this command to designate another algorithm. When a member leaves or is added to the ECMP group, the hash algorithm is recalculated to balance traffic across the members.
PAGE 553
FTOS provides a CLI-based solution for modifying the hash seed to ensure that on each configured system, the ECMP selection is same. When configured, the same seed is set for ECMP, LAG, and NH, and is used for incoming traffic only. NOTE: While the seed is stored separately on each port-pipe, the same seed is used across all CAMs. You cannot separate LAG and ECMP but you can use different algorithms across the chassis with the same seed.
PAGE 554
ip ecmp weighted Enables weighted ECMP calculations. Syntax ip ecmp weighted To disable weighted ECMP calculations, enter the no ip ecmp weighted command. Defaults N/A Command Modes CONFIGURATION Command History Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S-Series. Enabling this CLI would inform the FIB to re-program the destination prefix paths with weights in the HW/CAM on the fly.
PAGE 555
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. link-bundle-distribution trigger-threshold Provides a mechanism to set the threshold to trigger when traffic distribution begins being monitored on an ECMP link bundle.
PAGE 556
show config Display the ECMP configuration. Syntax show config Command Modes CONFIGURATION-ECMP-GROUP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 557
Example Version Description 8.3.7.0 Introduced on the S4810.
PAGE 558
16 FIPS Cryptography To configure federal information processing standards (FIPS) cryptography, use the following commands: fips mode enable Enable the FIPS cryptography mode on the platform. Syntax [no] fips mode enable To disable the FIPS cryptography mode, use the no fips mode enable command.
PAGE 559
Command Modes EXEC Example Dell#show fips status FIPS Mode : Disabled Dell# Dell#show fips status FIPS Mode : Enabled Dell# Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.
PAGE 560
Example Dell#show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256cbc,aes128-ctr,aes192-ctr,aes256-ctr. SSH server macs : hmac-sha1-96. SSH server kex algorithms : diffie-hellman-group14-sha1. Password Authentication : enabled. Hostbased Authentication : disabled. RSA Authentication : disabled. Vty Encryption HMAC Remote IP With FIPS Mode enabled: Dell#show ip ssh SSH server : enabled. SSH server version : v2.
PAGE 561
NOTE: The :: notation specifies successive hexadecimal fields of zeros. -c encryption cipher Enter the following encryption cipher to use. (For v2 clients only.) • 3des-cbc: Force ssh to use 3des-cbc encryption cipher. FIPS mode is enabled or disabled: • 3des-cbc: Force ssh to use 3des-cbc encryption cipher. • aes128–cbc: Force ssh to use the aes128–cbc encryption cipher. • aes192–cbc: Force ssh to use the aes256–cbc encryption cipher.
PAGE 562
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.1(0.0) Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 563
Dell#ssh 10.10.10.10 -c ? 3des-cbc Force ssh aes128-cbc Force ssh aes192-cbc Force ssh aes256-cbc Force ssh aes128-ctr Force ssh aes192-ctr Force ssh aes256-ctr Force ssh Dell#ssh 10.10.10.
PAGE 564
17 Force10 Resilient Ring Protocol (FRRP) FRRP is a proprietary protocol for that offers fast convergence in a Layer 2 network without having to run the spanning tree protocol (STP). The resilient ring protocol is an efficient protocol that transmits a high-speed token across a ring to verify the link status. All the intelligence is contained in the master node with practically no intelligence required of the transit mode. Important Points to Remember • FRRP is media- and speed-independent.
PAGE 565
Usage Information Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.5.1.0 Introduced. Executing this command without the optional ring-id command clears the statistics counters on all the available rings. Dell Networking OS requires a command line confirmation before the command executes.
PAGE 566
count number Enter the keyword count then the number of debug outputs. The range is from 1 to 65534. Defaults Disabled. Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 567
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. disable Disable the resilient ring protocol. Syntax disable To enable the Resilient Ring Protocol, use the no disable command.
PAGE 568
interface Configure the primary, secondary, and control-vlan interfaces. Syntax interface {primary interface secondary interface control-vlan vlan-id} To return to the default, use the no interface {primary interface secondary interface control-vlan vlan-id} command.
PAGE 569
Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Usage Information This command causes the Ring Manager to take ownership of the two ports after IFM validates the configuration. Ownership is relinquished for a port only when the interface does not play a part in any control VLAN, that is, the interface does not belong to any ring. Related Commands show frrp — displays the Resilient Ring Protocol configuration information.
PAGE 570
mode Set the Master or Transit mode of the ring. Syntax mode {master | transit} To reset the mode, use the no mode {master | transit} command. Parameters master Enter the keyword master to set the Ring node to Master mode. transit Enter the keywordtransit to set the Ring node to Transit mode. Defaults Mode None Command Modes CONFIGURATION (conf-frrp) Command History This guide is platform-specific.
PAGE 571
Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 572
Usage Information Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. Executing this command without the optional ring-id command clears the statistics counters on all the available rings.
PAGE 573
2 Dell# Related Commands Up Master 2 11-20, 25, 27-30 protocol frrp — enters the resilient ring protocol and designate a ring identification. timer Set the hello interval or dead interval for the Ring control packets. Syntax timer {hello-interval milliseconds}| {dead-interval milliseconds} To remove the timer, use the no timer {hello-interval [milliseconds]}| {deadinterval milliseconds} command.
PAGE 574
Usage Information 574 Version Description 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 7.4.1.0 Introduced. The hello interval command is the interval at which ring frames are generated from the primary interface of the master node. The dead interval command is the time that elapses before a time-out occurs.
PAGE 575
18 GARP VLAN Registration (GVRP) The Dell Networking operating system supports the basic GVRP commands on the Dell Networking OS. The generic attribute registration protocol (GARP) mechanism allows the configuration of a GARP participant to propagate through a network quickly. A GARP participant registers or de-registers its attributes with other participants by making or withdrawing declarations of attributes.
PAGE 576
clear gvrp statistics Clear GVRP statistics on an interface. Syntax clear gvrp statistics interface interface Parameters interface interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a port channel interface, enter the keywords port-channel then a number.
PAGE 577
debug gvrp Enable debugging on GVRP. Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters config Enter the keyword config to enable debugging on the GVRP configuration. event Enter the keyword event to enable debugging on the JOIN/LEAVE events.
PAGE 578
disable Globally disable GVRP. Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 579
Parameters join Enter the keyword join then the number of milliseconds to configure the join time. The range is from 100 to 147483647 milliseconds. The default is 200 milliseconds. NOTE: Designate the milliseconds in multiples of 100. leave Enter the keyword leave then the number of milliseconds to configure the leave time. The range is from 100 to 2147483647 milliseconds. The default is 600 milliseconds. NOTE: Designate the milliseconds in multiples of 100.
PAGE 580
Related Commands show garp timers — displays the current GARP times. gvrp enable Enable GVRP on physical interfaces and LAGs. Syntax gvrp enable To disable GVRP on the interface, use the no gvrp enable command. Defaults Disabled. Command Modes CONFIGURATION-INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 581
Parameters fixed Enter the keyword fixed then the VLAN range in a comma-separated VLAN ID set. normal Enter the keyword normal then the VLAN range in a comma-separated VLAN ID set. This setting is the default. forbidden Enter the keyword forbidden then the VLAN range in a comma-separated VLAN ID set. Defaults normal Command Modes CONFIGURATION-INTERFACE Command History This guide is platform-specific.
PAGE 582
protocol gvrp Access GVRP protocol — (config-gvrp)#. Syntax protocol gvrp Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 583
Related Commands Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series gvrp enable — enables GVRP on physical interfaces and LAGs. protocol gvrp — accesses the GVRP protocol. show garp timers Display the GARP timer settings for sending GARP messages.
PAGE 584
Example Dell#show garp timers GARP Timers Value (milliseconds) ---------------------------------------Join Timer 200 Leave Timer 600 LeaveAll Timer 10000 Dell# Related Commands garp timers — sets the intervals (in milliseconds) for sending GARP messages. show gvrp Display the GVRP configuration. Syntax show gvrp [brief | interface] Parameters Defaults brief (OPTIONAL) Enter the keyword brief to display a brief summary of the GVRP configuration.
PAGE 585
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Usage Information If no ports are GVRP participants, the message output changes from GVRP Participants running on to GVRP Participants running on no ports. Example R3#show gvrp brief GVRP Feature is currently enabled.
PAGE 586
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on C-Series, E-Series, and S-Series Invalid messages/attributes skipped can occur in the following cases: • The incoming GVRP PDU has an incorrect length.
PAGE 587
19 High Availability (HA) High availability (HA) in the Dell Networking operating software is configuration synchronization to minimize recovery time in the event of a route processor module (RPM) failure. The feature is available on Dell Networking OS. In general, a protocol is defined as “hitless” in the context of an RPM failure/failover and not failures of a line card, SFM, or power module. A protocol is defined as hitless if an RPM failover has no impact on the protocol.
PAGE 588
There is no need to reload or reboot the system when you insert the patch. The In-Service Modular patch replaces the existing process code. After installation is complete, the system executes the patch code as though it was always there. Related Commands show patch — displays the system patches loaded with the in-service modular hot fix command. process restartable Enable a process to be restarted. Restartability is subject to a maximum restart limit.
PAGE 589
redundancy auto-failover-limit Specify an auto-failover limit for RPMs. When a non-recoverable fatal error is detected, an automatic RPM failover occurs. This command does not affect user-initiated (manual) failovers. Syntax redundancy auto-failover-limit [count number [period minutes] | period minutes]] To disable the auto-failover limit control, use the no redundancy auto-failover-limit command.
PAGE 590
redundancy disable-auto-reboot Prevent the system from auto-rebooting the failed module. Syntax redundancy disable-auto-reboot stack-unit [0–11 | members} [rpm| card number | all] To return to the default, use the no redundancy disable-auto-reboot stack-unit rpm command. Parameters rpm Enter the keyword rpm to disable auto-reboot of the failed RPM. stack-unit Enter the keyword stack-unit then the stack-unit ID number. Default Disabled (that is, the failed module is automatically rebooted).
PAGE 591
redundancy force-failover Force the secondary stack unit to become the primary stack unit. You can also use this command to upgrade the software on one stack unit from the other when the other has been loaded with the upgraded software. Syntax Parameters redundancy force-failover stack-unit stack-unit Enter the keyword stack-unit then the stack-unit ID number. Default Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 592
rpm1 Enter the keyword rpm1 to set the RPM in slot R1 as the primary RPM. Default The RPM in slot R0 is the Primary RPM. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 593
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the E-Series. • show lacp — displays the lacp configuration. • show redundancy — displays the current redundancy configuration. redundancy reset-counter Reset failover counter and timestamp information displayed in the show redundancy command.
PAGE 594
redundancy sfm standby Place the SFM in an offline state. Syntax redundancy sfm standby To place the SFM in an online state, use the no redundancy sfm standby command. Default The SFM is online by default. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 595
! 10Dell(conf)#do show sfm all Switch Fabric State: up -- Switch Fabric Modules -Slot Status ------------------------------------------0 active 1 active redundancy synchronize Manually synchronize data once between the Master and Stand-by stack units. Syntax Parameters redundancy synchronize [full] full Enter the keyword full to synchronize all data. Default Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 596
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.2.1.0 Introduced on the E-Series.
PAGE 597
Process name Timestamp last crashed --------------------------------------------------------radius [5/23/2001 10:11:47] ---------------------------------------------------------Related Commands process restartable show redundancy Display the current redundancy configuration. Syntax Command Modes Command History show redundancy • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 598
Field Description RPM Redundancy Configuration Displays the following information: • which RPM is the preferred Primary on next boot (the redundancy primary command) • the data sync method configured (the redundancy synchronize command) • the failover type (you cannot change this type; it is software-dependent). Hot Failover means that the running configuration and routing table are applied on secondary RPM.
PAGE 599
-- RPM Failover Record ------------------------------------------------Failover Count: 1 Last failover timestamp: Jul 13 2007 21:25:32 Last failover Reason: User request -- Last Data Block Sync Record: ------------------------------------------------Line Card Config: succeeded Jul 13 2007 21:28:53 Start-up Config: succeeded Jul 13 2007 21:28:53 SFM Config State: succeeded Jul 13 2007 21:28:53 Runtime Event Log: succeeded Jul 13 2007 21:28:53 Running Config: succeeded Jul 13 2007 21:28:53 Dell# High Availab
PAGE 600
20 ICMP Message Types This chapter lists and describes the possible ICMP message type resulting from a ping. The first three columns list the possible symbol or type/code. For example, you would receive a ! or 03 as an echo reply from your ping. ICMP Messages and their Definitions. Table 1. ICMP Messages and their Definitions Symbol Type Code . 0 U 3 3 Error echo reply . destination unreachable: 0 network unreachable . 1 host unreachable . 2 protocol unreachable . 3 port unreachable .
PAGE 601
Symbol & Type Code Description Query 10 0 router solicitation . 11 Error time exceeded: 0 time-to-live equals 0 during transit . 1 time-to-live equals 0 during reassembly . 12 parameter problem: 1 IP header bad (catchall error) . 2 required option missing . 13 0 timestamp request . 14 0 timestamp reply . 15 0 information request (obsolete) . 16 0 information reply (obsolete) . 17 0 address mask request . 18 0 address mask reply .
PAGE 602
21 Internet Group Management Protocol (IGMP) The IGMP commands are supported by the Dell Networking operating software on the Dell Networking OS. IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant with RFC-3376. Important Points to Remember • Dell Networking OS supports protocol-independent multicast-sparse (PIM-SM) and protocol-independent source-specific multicast (PIM-SSM) include and exclude modes. • IGMPv2 is the default version of IGMP on interfaces.
PAGE 603
Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 604
Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 605
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on E-Series. The access list accepted is an extended ACL. To block IGMP reports from hosts, on a per-interface basis based on the group address and source address that you specify in the access list, use this feature.
PAGE 606
Version Description E-Series legacy command Usage Information Querier normally sends some group-specific queries when a leave message is received for a group prior to deleting a group from the membership database. There may be situations when you require immediate deletion of a group from the membership database. This command provides a way to achieve the immediate deletion. In addition, this command provides a way to enable immediate-leave processing for specified groups.
PAGE 607
Version Description E-Series legacy command ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters seconds Enter the number of seconds between queries sent out. The range is from 1 to 18000. The default is 60 seconds. Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 608
Usage Information If you have configured the hello interval value to be greater than 18000, you must first reset that value to be less than or equal to 18000 before upload. Otherwise, the command execution fails during bootup and the hello interval value is set to the default value. ip igmp query-max-resp-time Set the maximum query response time advertised in general queries. NOTE: The IGMP query-max-resp-time value must be less than the IGMP query-interval value.
PAGE 609
ip igmp ssm-map To translate (*,G) memberships to (S,G) memberships, use a statically configured list. Syntax ip igmp [vrf vrf-name] ssm-map std-access-list source-address Undo this configuration, that is, remove SSM map (S,G) states and replace them with (*,G) state, use the ip igmp [vrf vrf-name] ssm-map std-access-list source-address command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF.
PAGE 610
ip igmp version Manually set the version of the router to IGMPv2 or IGMPv3. Syntax ip igmp version {2 | 3} Parameters 2 Enter the number 2 to set the IGMP version number to IGMPv2. 3 Enter the number 3 to set the IGMP version number to IGMPv3. Defaults 2 (that is, IGMPv2) Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 611
group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and slot/port information: detail Command Modes Command History • EXEC • EXEC Privilege • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 612
Example Field Description Mode Displays the IGMP version used. Uptime Displays the amount of time the group has been operational. Expires Displays the amount of time until the entry expires. Last Reporter Displays the IP address of the last host to be a member of the IGMP group. Dell#show ip igmp groups Total Number of Groups: 5 IGMP Connected Group Membership Group Address Interface Uptime Expires 225.0.0.0 Vlan 100 00:00:05 00:02:04 Example (VLT) 225.0.0.1 Vlan 100 00:00:05 00:02:04 225.0.
PAGE 613
show ip igmp interface View information on the interfaces participating in IGMP. Syntax Parameters Command Modes Command History show ip igmp [vrf vrf-name] interface [interface] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IGMP interfaces associated with that VRF.
PAGE 614
The show ip igmp interface command does not display information corresponding to the loop-back interfaces.
PAGE 615
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. 7.7.1.0 Introduced on the E-Series. Example Dell#show ip igmp ssm-map Interface Vlan 20 Group 232.1.1.5 Uptime 00:11:22 Expires Never Router mode INCLUDE Last reporter 35.0.0.2 Group source list Source address Expires 65.0.0.1 00:01:22 65.0.0.2 00:01:22 65.0.0.3 00:01:22 65.0.0.4 00:01:22 65.0.0.
PAGE 616
• When enabled, IGMP snooping Querier starts after one query interval in case no IGMP general query (with IP SA lower than its VLAN IP address) is received on any of its VLAN members. • When enabled, IGMP snooping Querier periodically sends general queries with an IP source address of the VLAN interface. If it receives a general query on any of its VLAN member, it checks the IP source address of the incoming frame.
PAGE 617
Parameters snooping Enter the keyword snooping to enable debugging of IGMP snooping. group-address (OPTIONAL) Enter the IP multicast group address in dotted decimal format. interface interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 618
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To enable IGMP snooping, enter this command.
PAGE 619
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command. Usage Information Queriers normally send some queries when a leave message is received prior to deleting a group from the membership database. There may be situations when you require a fast deletion of a group. When you enable IGMP fast leave processing, the switch removes an interface from the multicast group as soon as it detects an IGMP version 2 leave message on the interface.
PAGE 620
ip igmp snooping last-member-query-interval The last member query interval is the maximum response time inserted into Group-Specific queries sent in response to Group-Leave messages. Syntax ip igmp snooping last-member-query-interval milliseconds To return to the default value, use the no ip igmp snooping last-member-query-interval command. Parameters milliseconds Enter the interval in milliseconds. The range is from 100 to 65535. The default is 1000 milliseconds.
PAGE 621
ip igmp snooping mrouter Statically configure a VLAN member port as a multicast router interface. Syntax ip igmp snooping mrouter interface interface To delete a specific multicast router interface, use the no igmp snooping mrouter interface interface command. Parameters interface interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 622
mrouter interface command in the VLAN context. The interface to the router must be a part of the VLAN where you are entering the command. ip igmp snooping querier Enable IGMP querier processing for the VLAN interface. Syntax ip igmp snooping querier To disable IGMP querier processing for the VLAN interface, use the no ip igmp snooping querier command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl-n) Command History This guide is platform-specific.
PAGE 623
Parameters group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on that group only. interface (OPTIONAL) Enter the interface type and slot/port information: detail Command Modes Command History • EXEC • EXEC Privilege • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 624
Example Dell#show ip igmp snooping groups Total Number of Groups: 1 IGMP Connected Group Membership Group Address Interface Mode Reporter 225.1.1.1 Vlan 10 IGMPv2-Compat Member Ports: Gi 1/17 Dell# Uptime Expires Last 00:00:07 00:02:09 1.1.1.2 show ip igmp snooping mrouter Display multicast router interfaces. Syntax show ip igmp snooping mrouter [vlan number] Parameters Command Modes Command History vlan number • EXEC • EXEC Privilege Enter the keyword vlan then the vlan number.
PAGE 625
Related Commands • ip igmp snooping mrouter — configures a static connection to the multicast router. • show ip igmp groups — view groups.
PAGE 626
22 Interfaces To configure egress, port channel, time domain, and UDP, use these interface commands. Basic Interface Commands The following commands are for Physical, Loopback, and Null interfaces. clear counters Clear the counters used in the show interfaces commands for all virtual router redundancy protocol (VRRP) groups, virtual local area networks (VLANs), and physical interfaces, or selected ones.
PAGE 627
NOTE: This command also enables you to clear the port configurations corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. • For non-ON platforms, you can specify multiple ports as slot/portrange. For example, if you want to clear the port configurations corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1 - 4.
PAGE 628
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Updated the definition of the learning-limit option for clarity. Example Dell#clear counters Clear counters on all interfaces [confirm] Related Commands mac learning-limit — allows aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. show interfaces — displays information on the interfaces.
PAGE 629
Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Example Dell#clear dampening gigabitethernet 1/10 Clear dampening counters on TeGi 1/10 [confirm] y Dell# Related Commands show interfaces dampening — displays interface dampening information. dampening — configures dampening on an interface. dampening Configure dampening on an interface.
PAGE 630
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. With each flap, Dell Networking OS penalizes the interface by assigning a penalty (1024) that decays exponentially depending on the configured half-life.
PAGE 631
corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.9(0.
PAGE 632
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 633
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 634
resume-offset Enter the offset value for generating PAUSE frames to resume traffic. Defaults Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Usage Information Version Description 9.8(1.0) Introduced on the Z9100–ON. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 635
• Speeds less than 1 Gig cannot be configured when the asymmetric flow control configuration is on. The following error is returned: Can’t configure speed <1G when Asymmetric flowcontrol is on, config ignored • Dell Networking OS only supports rx on tx on and rx off tx off for speeds less than 1 Gig (Symmetric). NOTE: If you use the disable rx flow control command, Dell Networking recommends rebooting the system.
PAGE 636
on on Related Commands on on on on on on • show running-config — display the flow configuration parameters (non-default values only). • show interfaces — display the negotiated flow control parameters. interface Configure a physical interface on the switch. Syntax interface interface range Parameters interface range Enter one of the following keywords and slot/port or number information: • For a null interface, enter the keyword null then the slot/port information.
PAGE 637
Usage Information Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Introduced You cannot delete a physical interface. By default, physical interfaces are disabled (shutdown) and are not assigned to an IP address or switchport.
PAGE 638
Enter the member VLANs using VLAN IDs (separated by commas), a range of VLAN IDs (separated by a hyphen), a single VLAN ID, or a combination. For example: VLAN IDs (comma-separated): 3, 4, 6. Range (hyphen-separated): 5-10. Slot/Port information need not contain a space before and after the dash. For example. both of the following commands are valid: ; interface group gigabitethernet 1/1 - 5 ; interface group gigabitethernet 1/1-5; .
PAGE 639
Parameters number Enter a number as the interface number. The range is from 0 to 16383. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 640
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 641
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 642
required between the commas. The ranges can include VLANs, port-channels, and physical interfaces. • For a port channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 643
• The interface range prompt includes interface types with slot/port information for valid interfaces. The prompt allows for a maximum of 32 characters. If the bulk configuration exceeds 32 characters, it is represented by an ellipsis ( ... ). • When the interface range prompt has multiple port ranges, the smaller port range is excluded from the prompt. • If overlapping port ranges are specified, the port range is extended to the smallest start port and the biggest end port.
PAGE 644
interface vlan — configures a VLAN interface. show config (from INTERFACE RANGE mode) — shows the bulk configuration interfaces. show range — shows the bulk configuration ranges. interface range macro (define) — defines a macro for an interface-range. interface range macro (define) Defines a macro for an interface range and then saves the macro in the running configuration. Syntax define interface range macro name interface , interface , ...
PAGE 645
Example (Single Range) Version Description 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.0 Added support for 4093 VLANs on E-Series ExaScale. Prior releases supported 2094. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. This example shows how to define an interface range macro named test.
PAGE 646
Example (Single Range) Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced This example shows the macro named test that was defined earlier.
PAGE 647
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1.(0.0) Introduced on the S4810; added support for OpenFlow. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. For more information about VLANs and the commands to configure them, refer to the Virtual LAN (VLAN) Commands section of the Layer 2 chapter. FTP, TFTP, and SNMP operations are not supported on a VLAN. MAC ACLs are not supported in VLANs. IP ACLs are supported.
PAGE 648
Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.
PAGE 649
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. This command is supported on C-Series, S-Series, and E-Series (TeraScale and ExaScale) 10/100/1000 Base-T Ethernet interfaces.
PAGE 650
Current address is 00:01:e8:05:f7:fc Interface index is 474791997 Internet address is 1.1.1.1/24 MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit, Mode full duplex, Master ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interfaces" counters 00:12:42 Queueing strategy: fifo Input Statistics: ... User Information Both sides of the link must have auto-negotiation enabled or disabled for the link to come up.
PAGE 651
Command Modes Command History • EXEC • EXEC Privilege • For a Tunnel interface, enter the keyword tunnel then the slot/port. The range is from 1 to 16383. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 652
Example (Single Interface) Key Description l Change the view to the next interface on the line card, or if in line card mode, the next line card in the chassis. a Change the view to the previous interface on the line card, or if in line card mode, the previous line card in the chassis. T Increase the screen refresh rate. t Decrease the screen refresh rate. q Return to the CLI prompt. systest-3 Monitor time: 00:00:06 Refresh Intvl.
PAGE 653
Gi 1/19 Down 0 0 0 0 Gi 1/20 Up 62734 54 62766 18 Gi 1/21 Up 60198 9 200899 9 Gi 1/22 Up 17304741100 3157554 10102508511 1114221 Gi 1/23 Up 17304769659 3139507 7133354895 523329 m - Change mode c - Clear screen b - Display bytes r - Display pkts/bytes per sec l - Page up a - Page down mtu Set the link maximum transmission unit (MTU) (frame size) for an Ethernet interface. Syntax mtu value To return to the default MTU value, use the no mtu command. Parameters value Enter a maximum frame size in bytes.
PAGE 654
port channels: • All members must have the same link MTU value and the same IP MTU value. • The port channel link MTU and IP MTU must be less than or equal to the link MTU and IP MTU values configured on the channel members. For example, if the members have a link MTU of 2100 and an IP MTU 2000, the port channel’s MTU values cannot be higher than 2100 for link MTU or 2000 bytes for IP MTU. VLANs: • All members of a VLAN must have same IP MTU value. • Members can have different Link MTU values.
PAGE 655
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. The following describes the interface command shown in the following example.
PAGE 656
Dell(conf-if-vl-20)#no tagged gigabitethernet 7/1 Dell(conf-if-vl-20)#interface gigabitethernet 7/1 Dell(conf-if-gi-7/0)#no portmode hybrid Dell(conf-if-vl-20)# rate-interval Configure the traffic sampling interval on the selected interface. Syntax rate-interval seconds Parameters seconds Enter the number of seconds for which to collect traffic data. The range is from 5 to 299 seconds.
PAGE 657
show config Display the interface configuration. Syntax show config Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 658
Example Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 659
NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. Command Modes Command History • EXEC • EXEC Privilege • For non-ON platforms, you can specify multiple ports as slot/port-range.
PAGE 660
Usage Information Version Description 6.3.1.0 Added the Pluggable Media Type field in the E-Series TeraScale output. Use the show interfaces command for details on a specific interface. NOTE: In the CLI output, the power value is rounded to a 3-digit value. For receive/transmit power that is less than 0.000, an snmp query returns the corresponding dbm value even though the CLI displays as 0.000.
PAGE 661
Line Description – Broadcasts = number of MAC broadcast packets • Number of runts, giants, and throttles packets: – runts = number of packets that are less than 64B – giants = packets that are greater than the MTU size – throttles = packets containing PAUSE frames • Number of CRC, overrun, and discarded packets: – CRC = packets with CRC/FCS errors – overrun = number of packets discarded due to FIFO overrun conditions – discarded = the sum of runts, giants, CRC, and overrun packets discarded without any
PAGE 662
0 CRC, 0 overrun, 0 discarded Output Statistics: 0 packets, 0 bytes, 0 underruns 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions, 0 wreddrops Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.
PAGE 663
Last clearing of "show interface" counters 04:01:08 Queueing strategy: fifo Input 943 packets, 78347 bytes, 190 multicast Received 0 errors, 0 discarded Output 459 packets, 102388 bytes, 15 multicast Output 0 errors, 0 invalid protocol Time since last interface status change: 00:03:09 Example (Management Ethernet, two IPv6 addresses) Dell#show interfaces managementethernet 1/1 ManagementEthernet 1/1 is up, line protocol is up Hardware is DellForce10Eth, address is 00:01:e8:a0:bf:f3 Current address is 00:01
PAGE 664
of-instance: 2 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:05:12 Queueing strategy: fifo Time since last interface status change: 00:05:12 Related Commands show interfaces configured – displays any interface with a non-default configuration.
PAGE 665
Version Description 6.4.1.0 Changed the organization of the display output. Example Dell#show interfaces configured GigabitEthernet 13/18 is up, line protocol is up Hardware is Force10Eth, address is 00:01:e8:05:f7:fc Current address is 00:01:e8:05:f7:fc Interface index is 474791997 Internet address is 1.1.1.
PAGE 666
• For ON platforms, you can specify multiple ports as slot/port/[subport] - slot/port/[subport]. For example, if you want to display information corresponding to all ports between 1 and 4, specify the port range as show interfaces interface-type 1/1/1 - 1/1/4. summary (OPTIONAL) Enter the keyword summary to display the current summary of dampening data, including the number of interfaces configured and the number of interfaces suppressed, if any.
PAGE 667
show interfaces configured — displays any interface with a non-default configuration. show interfaces phy Display auto-negotiation and link partner information. Syntax Parameters show interfaces gigabitethernet slot/port phy gigabitethernet Enter the keyword gigabitethernet then the slot/port information. tengigabitethernet Enter the keyword tengigabitethernet then the slot or port information. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 668
Usage Information The following describes the show interfaces gigabitethernet command following example. Mode Control Indicates if auto negotiation is enabled. If so, indicates the selected speed and duplex. Mode Status Displays auto negotiation fault information. When the interface completes auto negotiation successfully, the autoNegComplete field and the linkstatus field read “True.” AutoNegotiation Advertise Displays the control words the local interface advertises during negotiation.
PAGE 669
Loopback: False PowerDown: False Isolate: False DuplexMode: Full Mode Status: AutoNegComplete: False RemoteFault: False LinkStatus: False JabberDetect: False AutoNegotation Advertise: 100MegFullDplx: True 100MegHalfDplx: True 10MegFullDplx: False 10MegHalfDplx: True Asym Pause: False Sym Pause: False AutoNegotiation Remote Partner's Ability: 100MegFullDplx: False 100MegHalfDplx: False 10MegFullDplx: False 10MegHalfDplx: False Asym Pause: False Sym Pause: False AutoNegotiation Expansion: ParallelDetectionFau
PAGE 670
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series.
PAGE 671
• For a port channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. NOTE: This command also enables you to view information corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. Defaults Command Modes Command History • For non-ON platforms, you can specify multiple ports as slot/port-range.
PAGE 672
Gi Gi Gi Gi Gi Gi Gi Gi Gi Gi Gi Gi Related Commands 1/5 DellPort 1/6 1/7 1/8 1/9 1/10 1/11 1/12 1/13 1/14 1/15 1/16 Up Down Down Up Down Down Down Down Down Down Down Down 1000 Mbit Auto Auto Auto Auto Auto 1000 Mbit Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto 30-130 --1502,1504,1506-1508,1602 --------Dell# show interfaces — displays information on a specific physical interface or virtual interface.
PAGE 673
Version Description 9.9(0.0) Added support to display the interface configurations corresponding to a range of ports. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.2.1.
PAGE 674
Vlan 2 --More-Related Commands interface — configures a physical interface on the switch. show ip interface — displays Layer 3 information about the interfaces. show interfaces — displays information on a specific physical interface or virtual interface. show interfaces transceiver — displays the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number.
PAGE 675
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Output augmented with diagnostic data for pluggable media. 7.7.1.0 Removed three fields in the output: Vendor Name, Vendor OUI, and Vendor PN. 7.6.1.
PAGE 676
Interfaces Line Description Bias High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. TX Power High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. RX Power High Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Temp Low Warning threshold Factory-defined setting. Value can differ between SFP and SFP+. Voltage Low Warning threshold Factory-defined setting.
PAGE 677
Example Line Description Temperature High Alarm Flag This can be either true or false, depending on the Current voltage value displayed above. Voltage High Alarm Flag This can be either true or false, depending on the Current Temperature value displayed above. Tx Bias High Alarm Flag This can be either true or false, depending on the present Tx bias current value displayed above.
PAGE 678
SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP SFP 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Serial Base ID fields Id = 0x03 Ext Id = 0x04 Connector = 0x07 Transciever Code = 0x00 0x00 0x00 0x01 0x20 0x40 0x0c 0x05 Encoding = 0x01 BR Nominal = 0x15 Length(9um) Km = 0x00 Length(9um) 100m = 0x00 Length(50um) 10m = 0x1e Length(62.
PAGE 679
SFP 1 Tx Bias Low Alarm Flag = False SFP 1 Tx Power Low Alarm Flag = False SFP 1 Rx Power Low Alarm Flag = True =================================== !-------output truncated ------------------------Related Commands interface — configures a physical interface on the switch. show ip interface — displays Layer 3 information about the interfaces. show interfaces — displays information on a specific physical interface or virtual interface.
PAGE 680
ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 2d17h26m Queueing strategy: fifo Time since last interface status change: 2d17h26m Input Statistics: 0 packets, 0 bytes Output Statistics: 0 packets, 0 bytes, 0 underruns Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show range Display all interfaces configured using the interface range command.
PAGE 681
show interfaces — displays information on a specific physical interface or virtual interface. show running-config ecmp-group Display interfaces, LAG, or LAG link bundles being monitored for uneven traffic distribution using the ecmp-group monitoring enable command. The ECMP group could have a LAG or a list of 10G/40 interfaces (not just LAG link-bundles). Syntax show running-config ecmp-group Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 682
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The shutdown command marks a physical interface as unavailable for traffic.
PAGE 683
100 Enter the keyword 100 to set the interface’s speed to 10/100 Mb/s. NOTE: When this setting is enabled, only 100Base-FX optics are supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card. 1000 Enter the keyword 1000 to set the interface’s speed to 1000 Mb/s. Autonegotiation is enabled. For more information, refer to negotiation auto. NOTE: When this setting is enabled, only 100oBase-FX optics are supported on the LC-EH-GE-50P or the LC-EJ-GE-50P card.
PAGE 684
Related Commands duplex (10/100 Interfaces) — configures duplex mode on physical interfaces with the speed set to 10/100. negotiation auto — enables or disables auto-negotiation on an interface. speed (Management interface) Set the speed for the Management interface. Syntax speed {10 | 100 | 1000 | auto} To return to the default setting, use the no speed command. Parameters 10 Enter the keyword 10 to set the interface’s speed to 10 Mb/s.
PAGE 685
switchport Place an interface in Layer 2 mode. Syntax switchport [backup interface {gigabit slot/port | tengigabit slot/port | fortyGigE slot/port | port-channel number}] To remove an interface from Layer 2 mode and place it in Layer 3 mode, enter the no switchport command. If a switchport backup interface is configured, first remove the backup configuration.
PAGE 686
Usage Information Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Added the backup interface option. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series. If an IP address or VRRP group is assigned to the interface, you cannot use the switchport command on the interface.
PAGE 687
all Configure all applications. Defaults None. Command Modes EIS Mode (conf-mgmt-eis) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.
PAGE 688
clear management application pkt-cntr Clear management application packet counters for all management application types. Syntax clear management application pkt-cntr Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 689
management egress-interface-selection To make configured application traffic egress through the management port instead of the front-end (FE) port, enable and configure a management egress interface. Syntax management egress-interface-selection To disable and remove management egress interface selection (EIS) configurations, use the no management egress-interface-selection command. Defaults None. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 690
10.11.0.0/16 172.16.1.0/24 ManagementEthernet 1/1 10.11.192.4 Connected Active Connected Static show management application pkt-cntr Display the number of packets for each application type that have taken the management route. Syntax show management application pkt-cntr Defaults None. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 691
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000, S4810, and S4820T.
PAGE 692
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Defaults Not configured. Command Modes INTERFACE PORTCHANNEL Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 693
You can have 16 interfaces per Port Channel on the S-Series and Z-Series. The interfaces can be located on different line cards but must be the same physical type and speed (for example, all 1-Gigabit Ethernet interfaces). However, you can combine 100/1000 interfaces and GE interfaces in the same Port Channel.
PAGE 694
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series, E-Series, and S-Series. port-channel failover-group — accesses PORT-CHANNEL FAILOVER-GROUP mode to configure a LAG failover group. show interfaces port-channel — displays information on configured Port Channel groups.
PAGE 695
Usage Information Port Channel interfaces are logical interfaces and can be either in Layer 2 mode (by using the switchport command) or Layer 3 mode (by configuring an IP address). You can add a Port Channel in Layer 2 mode to a VLAN. The shutdown, description, and name commands are the only commands that you can configure on an interface while it is a member of a Port Channel.
PAGE 696
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.0 Introduced on the E-Series.
PAGE 697
Version Description 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. Usage Information This feature groups two LAGs to work in tandem as a supergroup. For example, if one LAG goes down, the other LAG is taken down automatically, providing an alternate path to reroute traffic, avoiding oversubscription on the other LAG. You can use both static and dynamic (LACP) LAGs to configure failover groups.
PAGE 698
show interfaces port-channel Display information on configured Port Channel groups. Syntax show interfaces port-channel [channel-number] [brief] [description] Parameters channel-number For a Port Channel interface, enter the keyword port-channel then a number. For the C-Series and S-Series, the range is from 1 to 128. NOTE: This command also enables you to view information corresponding to a range of ports.
PAGE 699
Version Description E-Series legacy command Usage Information Example The following describes the show interfaces port-channel command shown in the following example. Field Description Port-Channel 1... Displays the LAG’s status. In the Example, the status of the LAG’s LAG fatesharing group (“Failover-group”) is listed. Hardware is... Displays the interface’s hardware information and its assigned MAC address. Port-channel is part...
PAGE 700
Input 44506754 IP Packets, 0 Vlans 0 MPLS 41 64-byte pkts, 44502871 over 64-byte pkts, 249 over 127-byte pkts 407 over 255-byte pkts, 3127 over 511-byte pkts, 606 over 1023-byte pkts Received 0 input symbol errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 IP Checksum, 0 overrun, 0 discarded 1218120 packets output, 100745130 bytes, 0 underruns Output 5428 Multicasts, 4 Broadcasts, 1212688 Unicasts 1216142 IP Packets, 0 Vlans, 0 MPLS 0 throttles, 0 discarded Rate info (interval 299 sec): Input 01.
PAGE 701
show port-channel-flow Display an egress port in a given port-channel flow. Syntax Parameters show port-channel-flow outgoing-port-channel number incoming-interface interface {source-ip address destination-ip address} | {source-port number destination-port number} | {source-mac address destination-mac address {vlan vlanid | ether-type}} outgoing-portchannel number Enter the keywords outgoing-port-channel then the number of the port channel to display flow information.
PAGE 702
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Introduced on the S4810. Because this command calculates based on a Layer 2 hash algorithm, use this command to display flows for switched Layer 2 packets, not for routed packets (use the show ip flow command to display routed packets). The show port-channel-flow command returns the egress port identification in a given port-channel if a valid flow is entered.
PAGE 703
Syntax Parameters tdr-cable-test interface interface Enter the keyword GigabitEthernet then the slot/port information for the 100/1000 Ethernet interface. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 704
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7.0.0 Introduced on the S5000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.
PAGE 705
UDP Broadcast Commands The user datagram protocol (UDP) broadcast feature is a software-based method to forward low throughput (not to exceed 200 pps) IP/UDP broadcast traffic arriving on a physical or VLAN interface. Important Points to Remember • This feature is available only on the S4810, S4820T, S3048–ON, S4048–ON, Z9000 platforms. • Routing information protocol (RIP) is not supported with the UDP Broadcast feature.
PAGE 706
ip udp-helper udp-port Enable the UDP broadcast feature on an interface either for all UDP ports or a specified list of UDP ports. Syntax ip udp-helper udp-port [udp-port-list] To disable the UDP broadcast on a port, use the no ip udp-helper udp-port [udp-port-list] command. Parameters udp-port-list (OPTIONAL) Enter up to 16 comma-separated UDP port numbers. NOTE: If you do not use this option, all UDP ports are considered by default.
PAGE 707
show ip udp-helper Display the configured UDP helpers on all interfaces. Syntax show ip udp-helper Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 708
23 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for securing IP communications by authenticating and encrypting all packets in a session. Use IPSec between hosts, gateways, or hosts and gateways. IPSec uses a series of protocol functions to achieve information security: • Authentication Headers (AH) — Connectionless integrity and origin authentication for IP packets.
PAGE 709
esp-authentication esp-encryption • md5 — Use Message Digest 5 (MD5) authentication. • sha1 — Use Secure Hash Algorithm 1 (SHA-1) authentication. • null — Causes an encryption policy configured for the area to not be inherited on the interface. Enter the keywords esp-authentication then the transform type of operation to apply to traffic. The transform type represents the encryption or authentication applied to traffic. • md5 — Use Message Digest 5 (MD5) authentication.
PAGE 710
crypto ipsec policy Create a crypto policy used by ipsec. Syntax crypto ipsec policy name seq-num ipsec-manual To delete a crypto policy entry, use the no crypto ipsec policy name seq-num ipsec-manual command. Parameters name Enter the name for the crypto policy set. seq-num Enter the sequence number assigned to the crypto policy entry. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 711
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(1.0) Introduced on the Z9500.
PAGE 712
Usage Information Example Version Description 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(1.0) Introduced on the Z9500. • IPv4 addresses support only -/32 mask types. • IPv6 addresses support only -/128 mask types. • Configure match for bi-directional traffic for optimal routing. • Only TCP is supported.
PAGE 713
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.2) Introduced on the Z9000, S4810, and S4820T. 9.2(1.0) Introduced on the Z9500.
PAGE 714
show crypto ipsec policy Display the crypto policy configuration. Syntax show crypto ipsec policy Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(0.
PAGE 715
transform-set Specify the transform set the crypto policy uses. Syntax transform-set transform-set-name To delete a transform set from the crypto policy, use the no transform-set transform-set-name command. Parameters transform-setname Enter the name for the crypto policy transform set. Defaults none Command Modes CONFIG-CRYPTO-POLICY Command History This guide is platform-specific.
PAGE 716
24 IPv4 Routing The basic IPv4 commands are supported by Dell Networking operating system on the platform. arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). Syntax arp [vrf vrf-name] ip-address mac-address interface To remove an ARP address, use the no arp ip-address command. Parameters vrf vrf-name Enter a VRF name to configure an ARP entry for that VRF. Use the VRF option after the keyword arp to configure a static arp on that particular VRF.
PAGE 717
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.4(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.
PAGE 718
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. Usage Information This timer is an exponential backoff timer. Over the specified period, the time between ARP requests increases.
PAGE 719
Usage Information In Dell Networking OS versions prior to 8.3.1.0, if a gratuitous ARP is received some time after an ARP request is sent, only RP2 installs the ARP information. For example: 1. At time t=0, Dell Networking OS sends an ARP request for IP A.B.C.D. 2. At time t=1, Dell Networking OS receives an ARP request for IP A.B.C.D. 3. At time t=2, Dell Networking OS installs an ARP entry for A.B.C.D only on RP2. Beginning with Dell Networking OS version 8.3.1.
PAGE 720
arp retries Set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. Syntax arp retries number Parameters number Enter the number of retries. The range is from 1 to 20. The default is 5. Defaults 5 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 721
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 722
ip ip-address (OPTIONAL) Enter the keyword ip then the IP address of the ARP entry you wish to clear. no-refresh (OPTIONAL) Enter the keywords no-refresh to delete the ARP entry from CAM. Or use this option with interface or ip ip-address to specify which dynamic ARP entries you want to delete. NOTE: Transit traffic may not be forwarded during the period when deleted ARP entries are resolved again and re-installed in CAM. Use this option with extreme caution.
PAGE 723
Parameters name Enter the name of the host to delete. Enter * to delete all host table entries. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 724
Usage Information Version Description 9.4(0.0) Added support for VRF. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.19.0 Introduced on the S4820T. To clear Layer 3 CAM inconsistencies, use this command. CAUTION: Executing this command causes traffic disruption. Related Commands show ip fib stack-unit — shows FIB entries on a specified stack-unit. clear ip route Clear one or all routes in the routing table.
PAGE 725
Usage Information Version Description 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Use the vrf vrf-name attribute of this command to clear routes corresponding to either a specific VRF or the default VRF. You cannot use this attribute to clear routes corresponding to a management VRF. Related Commands ip route — assigns an IP route to the switch. show ip route — views the routing table.
PAGE 726
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. debug arp View information on ARP transactions. Syntax debug arp [interface] [count value] To stop debugging ARP transactions, use the no debug arp command.
PAGE 727
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.
PAGE 728
Version Description 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.4.10 Introduced on the E-Series. Example Dell#debug ip dhcp 00:12:21 : %RELAY-I-PACKET: BOOTP REQUEST (Unicast) received at interface 113.3.3.17 BOOTP Request, hops = 0, XID = 0xbf05140f, secs = 0, hwaddr = 00:60:CF:20:7B:8C, giaddr = 0.0.0.
PAGE 729
debug ip icmp View information on the internal control message protocol (ICMP). Syntax debug ip icmp [interface] [count value] To disable debugging, use the no debug ip icmp command. Parameters interface count value (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 730
Example Usage Information Version Description 6.3.1.0 Added the count option. ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: ICMP: echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.40.40.40, echo src 40.40.40.40, dst 40.40.40.40, echo echo request sent to dst 40.40.40.40 echo request rcvd from src 40.40.40.40 src 40.40.40.40, dst 40.40.40.40, echo src 40.40.40.40, dst 40.40.40.40, echo echo request sent to dst 40.40.40.
PAGE 731
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Added support for 4094 VLANs on the E-Series ExaScale (the prior limit was 2094). 8.1.1.
PAGE 732
TCP src=23, dst=40869, seq=2112994896, ack=606901739, win=8192 ACK PUSH IP: s=10.1.2.216 (Ma 1/1), d=10.1.2.255, len 78, rcvd UDP src=0, dst=0 IP: s=10.1.2.62 (local), d=10.1.2.3 (Ma 1/1), len 1500, sending fragment IP Fragment, Ident = 4741, fragment offset = 0 ICMP type=0, code=0 IP: s=10.1.2.62 (local), d=10.1.2.3 (Ma 1/1), len 1500, sending fragment IP Fragment, Ident = 4741, fragment offset = 1480 IP: s=40.40.40.40 (local), d=224.0.0.5 (Gi 4/11), len 64, sending broad/ multicast proto=89 IP: s=40.40.
PAGE 733
To delete an IP address from an interface, use the no ip address [ip-address] command. Parameters ip-address Enter an IP address in dotted decimal format. mask Enter the mask of the IP address in slash prefix format (for example, /24). secondary (OPTIONAL) Enter the keyword secondary to designate the IP address as the secondary address. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 734
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 735
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To configure a list of possible domain names, configure the ip domain-list command up to six times.
PAGE 736
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. To fully enable DNS, also specify one or more domain name servers with the ip name-server command.
PAGE 737
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. You can only configure one domain name with the ip domain-name command.
PAGE 738
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Added support for IPv6. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.9.1.0 Introduced VRF on the E-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 739
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 740
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 741
Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.3(0.0) Introduced on the S4810, S4820T, S6000, and Z9000 platforms.
PAGE 742
Defaults Not configured. Command Modes CONFIGURATION Command History Usage Information • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Version Description 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 743
Parameters count Enter a number for the number of fragments allowed for re-assembly. The range is from 2 to 256. Defaults No limit is set on number of fragments allowed. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 744
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version 9.4.(0.0) Introduced on the S4810 and S4820T. Usage Information Use this command to specify the maximum number of protocol routes that the Route Table Manager can hold for a specific VRF. This command does not apply to the management VRFs.
PAGE 745
Starting with Dell Networking OS Release 9.2(0.2), the ip mtu command is not supported to configure the IP MTU value that is used when the IP packet is fragmented. Instead of having to configure the IP MTU value, this value is automatically computed by the software when you configure an interface. As a result, the ip mtu command is not available for configuration. However, you can continue to specify the link MTU value by using the mtu command.
PAGE 746
ip name-server Enter up to six IPv4 addresses of name servers. The order you enter the addresses determines the order of their use. Syntax ip name-server ipv4-address [ipv4-address2...ipv4-address6] To remove a name server, use the no ip name-server ip-address command. Parameters ipv4-address Enter the IPv4 address, in dotted decimal format, of the name server to be used. ipv4-address2... ipv4-address6 (OPTIONAL) Enter up five more IPv4 addresses, in dotted decimal format, of name servers to be used.
PAGE 747
ip proxy-arp Enable proxy ARP on an interface. Syntax ip proxy-arp To disable proxy ARP, use the no ip proxy-arp command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 748
To delete all routes matching a certain route, use the no ip route destination mask command. Parameters vrf vrf-name (Optoinal) Enter the keyword vrf and then the name of the VRF to configure a static route corresponding to that VRF. Use this VRF option after the ip route keyword to configure a static route on that particular VRF. destination Enter the IP address in dotted decimal format of the destination device. mask Enter the mask in the slash prefix format (/x) of the destination IP address.
PAGE 749
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.
PAGE 750
A route is considered for weighted ECMP calculations only if each paths corresponding to that route is configured with a weight. You cannot use the VRF attribute of this command to configure routes in a management VRF. When a specific VRF is deleted, all the configured static routes corresponding to that VRF are automatically removed. Example Dell(conf)#ip route 1.1.1.0/24 4.4.4.2 weight 100 Dell(conf)#ip route 1.1.1.0/24 6.6.6.2 weight 200 Dell(conf)#do show running-config | grep route ip route 1.1.1.
PAGE 751
Version Description 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip unreachables Enable the generation of internet control message protocol (ICMP) unreachable messages. Syntax ip unreachables To disable the generation of ICMP messages, use the no ip unreachables command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 752
load-balance By default, for C-Series and S-Series, Dell Networking OS uses an IP 4-tuple (IP SA, IP DA, Source Port, and Destination Port) to distribute IP traffic over members of a Port Channel as well as equal-cost paths. To designate another method to balance traffic over Port Channel members, use the load-balance command.
PAGE 753
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.10.0 Added the ingress-port parameter for the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 754
mac [source-mac | source-port-id | source-module-id | dest-mac | destport-id | destmodule-id | vlan | ethertype | sourcedest-mac ] tunnel [ipv4-overipv4 | ipv4-overgre-ipv4 | mac-inmac]} • protocol — Use IPv4 protocol field in hash calculation. • vlan — Use vlan field in hash calculation. • L4-source-port — Use IPv4 L4-source-port field in hash calculation. • L4-dest-port — Use IPv4 L4-dest-port field in hash calculation.
PAGE 755
management route Configure a static route that points to the Management interface or a forwarding router. Syntax management route {{ip-address mask | {ipv6-address prefix-length}} {forwarding-router-address | managementethernet| vlan | gigabitethernet | tengigabitethernet} To remove a static route, use the no management route{{ip-address mask | {ipv6-address prefix-length}}{forwarding-router-address | managementethernet | fortyGigE | vlan | gigabitethernet | tengigabitethernet} command.
PAGE 756
Version Description 8.3.11.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information When a static route (or a protocol route) overlaps with Management static route, the static route (or a protocol route) is preferred over the Management Static route. Also, Management static routes and the Management Connected prefix are not reflected in the hardware routing tables.
PAGE 757
• database — view a list of ARP entries learned using DAI • statistics — view DAI statistics macaddress macaddress mask (OPTIONAL) Enter the keyword macaddress then a MAC address in nn:nn:nn:nn:nn:nn format. Enter the optional MAC address mask in nn:nn:nn:nn:nn format also. static (OPTIONAL) Enter the keyword static to view entries entered manually. retries (OPTIONAL) Enter the keyword retries to show the number of ARP retries before a 20–second back off.
PAGE 758
Clear arp in-progress. Please try after sometime! The following describes the show arp command shown in the following example. Description Example Protocol Displays the protocol type. Address Displays the IP address of the ARP entry. Age(min) Displays the age (in minutes) of the ARP entry. Hardware Address Displays the MAC address associated with the ARP entry. Interface Displays the first two letters of the interfaces type and the slot/port associated with the ARP entry.
PAGE 759
Example (Summary) #show arp summary TotalEntries Static Entries Dynamic Entries CPU ---------------------------------------------83 0 83 CP Dell Related Commands ip local-proxy-arp — enables/disables Layer 3 communication in secondary VLANs. switchport mode private-vlan — sets PVLAN mode of the selected port. show arp retries Display the configured number of ARP retries. Syntax Command Modes Command History show arp retries • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 760
show hosts View the host table and DNS configuration. Syntax show hosts Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 760 IPv4 Routing Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 761
Field Description Also included in the flag is an indication of the validity of the route: Example Related Commands • ok — the entry is valid. • ex — the entry expired. • ?? — the entry is suspect. TTL Displays the amount of time until the entry ages out of the cache. For dynamically learned entries only. Type Displays IP as the type of entry. Address Displays the IP addresses assigned to the host.
PAGE 762
[detail [group-index index-number]]} summary Command Modes Command History • EXEC • EXEC Privilege • Enter the keyword detail to view the ECMP group index. • Enter the keyword member-info to view the member information for the ECMP group. • Enter the keyword member-info detail to view detailed ECMP membership and n-hop information. • Enter the keyword group-index then the index number to show ECMP membership per group. The range is from 0 to 1022.
PAGE 763
Example Dell#show ip cam stack-unit 3 po 0 1.1.1.0/24 longer-prefixes Destination EC C VId Mac-Addr Port ----------------------------------------------------------1.1.1.2/32 0 0 3000 00:05:00:00:00:02 Gi 3/44 1.1.1.1/32 0 1 0 00:00:00:00:00:00 CP 1.1.1.
PAGE 764
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 765
2.1.1.0/24 Direct, Vl 20 0.0.0.0 CP 20 0 2.1.1.1/32 via 127.0.0.1 127.0.0.1 CP 0 0 100.1.1.0/24 via 1.1.1.2, Vl 1000 1.1.1.2 Gi 3/42 1000 1 100.1.1.0/24 via 2.1.1.2, Vl 20 2.1.1.2 Po 10 20 1 Dell# Dell#show ip route 10.1.1.0/24 via via S 20.1.1.0/24 via S 100.1.1.0/24 via via S Example (Show command output with Weighted ECMP Enabled) 00:00:00:00:00:00 00:00:00:00:00:00 00:01:00:00:00:02 00:03:00:00:00:02 1.1.1.2, Vl 10 2.1.1.2, Vl 20 3.1.1.2, Vl 30 10.1.1.0, weight 7 20.1.1.
PAGE 766
protocol number [tcp | udp] Enter the keyword protocol then one of the protocol type keywords: tcp, udp, or protocol number The protocol number range is from 0 to 255. . src-port number Enter the keywords src-port then the source port number. destination-port number Enter the keywords destination-port then the destination port number. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 767
show ip interface View IP-related information on all interfaces. Syntax Parameters show ip interface [interface | brief] [configured] interface (OPTIONAL) Enter the following keywords and slot/port or number information: Command Modes Command History • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 768
Usage Information Example Version Description 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 8.1.1.2 Supported on the E-Series ExaScale E600i. 8.1.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show ip interface command shown in the following example.
PAGE 769
Example (Brief) Fields Description Method Displays “Manual” if the configuration is read from the saved configuration. Status States whether the interface is enabled (up) or disabled (administratively down). Protocol States whether IP is enabled (up) or disabled (down) on the interface.
PAGE 770
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Dell#show ip management-route Destination ----------10.1.2.0/24 172.16.1.0/24 Dell# Gateway ------ManagementEthernet 1/1 10.1.2.
PAGE 771
Example Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.4.1.0 Introduced on the C- and E-Series. 8.3.7.0 Introduced on the S4810. Dell#show ipv6 management-route IPv6 Destination Gateway ---------------------2001:34::0/64 ManagementEthernet 1/1 2001:68::0/64 2001:34::16 Dell# State ----Connected Active show ip protocols View information on all routing protocols enabled and active on the switch.
PAGE 772
Example Version Description pre-6.1.1.0 Introduced on the E-Series. Dell#show ip protocols Routing Protocol is "bgp 1" Cluster Id is set to 20.20.20.3 Router Id is set to 20.20.20.3 Fast-external-fallover enabled Regular expression evaluation optimization enabled Capable of ROUTE_REFRESH For Address Family IPv4 Unicast BGP table version is 0, main routing table version 0 Distance: external 20 internal 200 local 200 Neighbor(s): Address : 20.20.20.
PAGE 773
Command Modes Command History process-id (OPTIONAL) Specify that only OSPF routes with a certain process ID must be displayed. routing-tag (OPTIONAL) Specify that only ISIS routes with a certain routing tag must be displayed. connected (OPTIONAL) Enter the keyword connected to view only the directly connected routes. all (OPTIONAL) Enter the keyword all to view both active and non-active routes. static (OPTIONAL) Enter the keyword static to view only routes the ip route command configures.
PAGE 774
Field Description • B = BGP • IN = internal BGP • EX = external BGP • LO = Locally Originated • O = OSPF • IA = OSPF inter area • N1 = OSPF NSSA external type 1 • N2 = OSPF NSSA external type 2 • E1 = OSPF external type 1 • E2 = OSPF external type 2 • i = IS-IS • L1 = IS-IS level-1 • L2 = IS-IS level-2 • IA = IS-IS inter-area • * = candidate default • > = non-active route • + = summary routes The weight for weighted ECMP route calculations is displayed for each path in the
PAGE 775
Example (Summary) Dell#show ip route summary Route Source Active Routes Non-active Routes connected 2 0 static 1 0 Total 3 0 Total 3 active route(s) using 612 bytes R1_E600i>show ip route static ? | Pipe through a command R1_E600i>show ip route static Destination Gateway Dist/Metric Last Change ----------- ------- ----------- ----------*S 0.0.0.0/0 via 10.10.91.9, Gi 1/2 1/0 3d2h Dell> Example (With Weighted ECMP Enabled) Dell(conf)#ip route 1.1.1.0/24 6.6.6.2 weight 100 Dell(conf)#ip route 1.1.1.
PAGE 776
Last update 00:05:01 ago Routing Descriptor Blocks: * 4.4.4.2, via GigabitEthernet 1/4 * 6.6.6.2, via GigabitEthernet 1/16 Dell(conf)# show ip route list Display IP routes in an IP prefix list. Syntax show ip route vrf vrf-name list prefix-list Parameters Command Modes Command History prefix-list Enter the name of a configured prefix list. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to display IP routes in an IP prefix list corresponding to that VRF.
PAGE 777
N2- OSPF NSSA external type 2, E1 - OSPF external type 1, E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default, >- non-active route, + - summary route Gateway of last resort is not set R R R R C Related Commands Destination ----------2.1.0.0/24 2.1.1.0/24 2.1.2.0/24 2.1.3.0/24 2.1.4.0/24 Gateway ------via 2.1.4.1, Gi via 2.1.4.1, Gi via 2.1.4.1, Gi via 2.1.4.
PAGE 778
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The following describes the show ip route summary shown in the following example. Column Heading Description Example Route Source Identifies how the route is configured in Dell Networking OS. Active Routes Identifies the best route if a route is learned from two protocol sources.
PAGE 779
rp1 (OPTIONAL) Enter the keyword rp1 to view only the statistics from Route Processor 1. rp2 (OPTIONAL) Enter the keyword rp2 to view only the statistics from Route Processor 2. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.
PAGE 780
Keyword Definition ... too big Number of invalid IP fragments received. ... couldn’t fragment Number of packets that could not be fragmented and forwarded. ...encapsulation failed Counts packets which could not be forwarded due to ARP resolution failure. Dell Networking OS sends an arp request prior to forwarding an IP packet. If a reply is not received, Dell Networking OS repeats the request three times. These packets are counted in encapsulation failed. Rcvd: ...
PAGE 781
Sent: 21 requests, 10 replies (0 proxy) Routing Processor1 IP Traffic: show tcp statistics View information on TCP traffic through the switch. Syntax Parameters show tcp statistics {all | cp} all Enter the keyword all to view all TCP information. cp Enter the keyword cp to view only TCP information from the Control Processor. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 782
Example Field Description 329 packets... Displays the number of packets and bytes received in sequence. 17 dup... Displays the number of duplicate packets and bytes received. 0 partially... Displays the number of partially duplicated packets and bytes received. 7 out-of-order... Displays the number of packets and bytes received out of order. 0 packets with data after window Displays the number of packets and bytes received that exceed the switch’s window size.
PAGE 783
Sent: 12007 Total, 0 urgent packets 25 control packets (including 24 retransmitted) 11603 data packets (12439677 bytes) 24 data packets (7638 bytes) retransmitted 355 ack only packets (41 delayed) 0 window probe packets, 0 window update packets 7 Connections initiated, 8 connections accepted, 15 connections established 14 Connections closed (including 0 dropped, 0 embryonic dropped) 20 Total rxmt timeout, 0 connections dropped in rxmt timeout 0 Keepalive timeout, 0 keepalive probe, 0 Connections dropped in
PAGE 784
25 IPv6 Access Control Lists (IPv6 ACLs) IPv6 ACLs and IPv6 Route Map commands are supported on Dell Networking OS. NOTE: For IPv4 ACL commands, refer to the Access Control Lists (ACL) chapter. Important Points to Remember • Certain platforms require manual CAM usage space allotment. For more information, refer to the cam-acl command. • Egress IPv6 ACL and IPv6 ACL on the Loopback interface is not supported. • Reference to an empty ACL permits any traffic.
PAGE 785
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series TeraScale. 7.8.1.0 Introduced on the C-Series.
PAGE 786
Example Version Description 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.4.2.0 Introduced on the E-Series TeraScale. 7.8.1.0 Introduced on the C-Series.
PAGE 787
-- Line card 4 -Current L2Acl : Ipv4Acl : Ipv6Acl : Ipv4Qos : L2Qos : Settings(in block sizes) 2 2 4 2 3 Dell#show cam-acl Related Commands cam-acl — configures CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a filter.
PAGE 788
permit To configure a filter that matches the filter criteria, select an IPv6 protocol number, ICMP, IPv6, TCP, or UDP. Syntax permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} To remove this filter, you have two choices: Parameters • Use the no seq sequence-number command syntax if you know the filter’s sequence number • Use the no permit {ipv6-protocol-number | icmp | ipv6 | tcp | udp} command ip-protocol-number Enter an IPv6 protocol number. The range is from 0 to 255.
PAGE 789
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. ipv6 access-list Configure an access list based on IPv6 addresses or protocols.
PAGE 790
Usage Information Version Description 9.4(0.0) Added support for CoPP for OSPFv3 on the S4810, S4820T, S6000, and Z9000 platforms. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000 8.3.11.1 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the S-Series. 8.2.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series. Increased the name string to accept up to 140 characters.
PAGE 791
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.2.0 Introduced on the E-Series TeraScale. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series.
PAGE 792
• l2acl 1-10 ipv4acl 1-10 ipv6acl 0-10 ipv4qos 1-10 l2qos 1-10 L2 QoS (l2qos): 1 Allocate space to support IPv6 ACLs. Enter all of the profiles and a range. Enter the CAM profile name then the amount to be allotted. The total space allocated must equal 13. The ipv6acl range must be a factor of 2. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 793
26 IPv6 Basics IPv6 basic commands are supported on the Dell Networking OS. NOTE: For information about the Dell Networking operating software version and platform that supports IPv6 in each software feature, refer to the IPv6 Addressing chapter of the Dell Networking OS Configuration Guide. clear ipv6 fib Clear (refresh) all forwarding information base (FIB) entries on a linecard or stack unit.
PAGE 794
Version Description 7.4.1.0 Introduced on the E-Series TeraScale. clear ipv6 route Clear (refresh) all or a specific route from the IPv6 routing table. Syntax clear ipv6 route [vrf vrf-name] {* | ipv6-address prefix-length} Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to clear the IPv6 routes corresponding to that VRF. * Enter the * to clear (refresh) all routes from the IPv6 routing table.
PAGE 795
clear ipv6 mld_host Clear the IPv6 MLD host counters and reset the elapsed time. Syntax clear ipv6 mld_host Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 796
Command Modes CONFIGURATION-VRF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OSCommand Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000-ON, and Z9500.
PAGE 797
• If auto-configuration is enabled, all IPv6 addresses on that management interface are auto-configured. Manual and auto-configurations are not supported on a single management interface. • Removing auto-configuration removes all auto-configured IPv6 addresses and the link-local IPv6 address from that management interface. • IPv6 addresses on a single management interface cannot be members of the same subnet.
PAGE 798
Usage Information Example Version Description 7.8.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series TeraScale. • If two addresses are configured, delete an existing address before configuring a new address. • If the last manually-configured global IPv6 address is removed using the “no” form of the command, the link-local IPv6 address is removed automatically. • IPv6 addresses on a single management interface cannot be members of the same subnet.
PAGE 799
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.2) Introduced. Usage Information This command allows you to create an EUI64 address based on the specified prefix and MAC address only.
PAGE 800
Version Description 8.3.7.0 Introduced on the S4810. ipv6 flowlabel-zero Configure system to set the flow label field in the packets to zero. Syntax ipv6 flowlabel-zero To disable the 0 from being set in the field and allow the protocol operations to fill the field, use the no ipv6 flowlabel-zero command. Default Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 801
ipv6-address Enter the IPv6 address (X:X:X:X::X) to be mapped to the name. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.
PAGE 802
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.1.0 Introduced on the E-Series TeraScale. You can separately configure both IPv4 and IPv6 domain name servers.
PAGE 803
ipv6 nd dns-server Configures Recursive DNS Server (RDNSS) addresses to be distributed via IPv6 router advertisements to an IPv6 device. Syntax ipv6 nd dns-server {ipv6-RDNSS-address} {lifetime | infinite} To remove the IPv6 RDSS configuration, use no ipv6 nd dns-server {ipv6-RDNSS-address} {lifetime | infinite} Parameters ipv6-RDNSSaddress Enter the IPv6 Recursive DNS Server’s (RDNSS) address. You can specify up to 4 IPv6 RDNSS server addresses. lifetime Enter the lifetime in seconds.
PAGE 804
no-advertise Enter the keyword no-advertise to prevent the specified prefix from being advertised. no-autoconfig Enter the keywords no-autoconfig to disable Stateless Address Autoconfiguration. no-rtr-address Enter the keyword no-rtr-address to exclude the full router address from router advertisements (the R bit is not set). off-link Enter the keywords off-link to advertise the prefix without stating to recipients that the prefix is either on-link or off-link.
PAGE 805
ipv6 route Establish a static IPv6 route. Syntax ipv6 route [vrf vrf-name] ipv6-address prefix-length {ipv6-address | interface | interface ipv6-address} [distance] [tag value] [permanent] [weight weight-value] To remove the IPv6 route, use the no ipv6 route [vrf vrf-name]ipv6-address prefixlength {ipv6-address | interface | interface ipv6-address} [distance] [tag value] [permanent] [weight] command.
PAGE 806
NOTE: If you disable the interface with an IPv6 address associated with the keyword permanent, the route disappears from the routing table. weight weightvalue Enter the keyword weight followed by a weight value. The range is from 0 to 255. NOTE: Weight for a static route can be added only for the destination address and not for the route pointing to destination a interface. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 807
Dell(conf)#ipv6 route vrf vrf_test 44::/64 33::1 weight 100 Dell(conf)#ipv6 route vrf vrf_test 44::/64 33::2 weight 200 Dell(conf)#do show running-config | grep ipv6 route vrf Related Commands show ipv6 route — views the IPv6 configured routes. ipv6 unicast-routing Enable IPv6 unicast routing on the device. Syntax ipv6 unicast-routing To disable unicast routing, use the no ipv6 unicast-routing command. Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 808
• the IPv6 address family configuration (under router bgp) is deleted • IPv6 Multicast traffic continues to flow unhindered show ipv6 cam stack-unit Displays the IPv6 CAM entries for the specified stack-unit. Syntax show ipv6 cam [vrf vrf-name] stack-unit unit-number port-set {0-1} [summary | index | ipv6 address] Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display IPv6 CAM entries corresponding to that VRF.
PAGE 809
Version Description 8.4.2.1 Introduced on the S-Series. Usage Information NOTE: If a route has a mask greater than 64, no output is displayed and no output is displayed for show ipv6 cam stack-unit unit-number port-set {0-1} ipv6-address, but an equivalent /64 entry would be listed in the show ipv6 cam stack-unit unit-number port-set {0-1} output.
PAGE 810
show ipv6 fib stack-unit View all FIB entries. Syntax show ipv6 fib [vrf vrf-name] stack-unit unit-number [summary | ipv6address] Parameters vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to display neighbors corresponding to that VRF. slot-number Enter the number of the stack unit. summary (OPTIONAL) Enter the keyword summary to view a summary of entries in IPv6 cam.
PAGE 811
show ipv6 flowlabel-zero Display the flow label zero setting. Syntax show ipv6 flowlabel-zero Default Disabled Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 812
• Defaults For a tunnel interface, enter the keyword tunnel then the tunnel ID. brief (OPTIONAL) View a summary of IPv6 interfaces. configured (OPTIONAL) View information on all IPv6 configured interfaces. gigabitethernet (OPTIONAL) View information for an IPv6 gigabitethernet interface. managementethern et slot/ port (OPTIONAL) View information on an IPv6 Management port. Enter the slot number (0-1) and port number zero (0). loopback (OPTIONAL) View information for IPv6 Loopback interfaces.
PAGE 813
Usage Information The Management port is enabled by default (no shutdown). If necessary, use the ipv6 address command to assign an IPv6 address to the Management port.
PAGE 814
Example (tunnel) Dell#show ipv6 interface tunnel 1 Tunnel 1 is up, line protocol is up IPV6 is enabled Link Local address: fe80::201:e8ff:fea7:497e Global Unicast address(es): 400::1, subnet is 400::/64 (MANUAL) Remaining lifetime: infinite Global Anycast address(es): Joined Group address(es): ff02::1 ff02::2 ff02::1:ff00:1 ff02::1:ffa7:497e ND MTU is 0 ICMP redirects are not sent DAD is enabled, number of DAD attempts: 3 ND reachable time is 20410 milliseconds ND base reachable time is 30000 milliseconds
PAGE 815
Example Field Description Valid MLD Packets The total number of packets received and sent from the last time the elapsed time was cleared. Reports The total number of reports (queries and unsolicited reports generated from joins or leaves) that have been received or sent. Leaves The number of Multicast leaves that have been sent. MLDv1 queries The number of MLDv1 queries that have been received. MLDv2 queries The number of MLDv2 queries that have been received.
PAGE 816
Defaults list (OPTIONAL) View the IPv6 prefix list. ospf (OPTIONAL) View information for all IPv6 OSPF routes. rip (OPTIONAL for E-Series only) View information for all IPv6 RIP routes. static (OPTIONAL) View only routes configured by the ipv6 route command. summary (OPTIONAL) View a brief list of the configured IPv6 routes. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 817
Field Example (S-Series) Description • E2 = OSPF external type 2 • i = IS-IS • L1 = IS-IS level-1 • L2 = IS-IS level-2 • IA = IS-IS inter-area • * = candidate default • > = non-active route • + = summary routes Destination Identifies the route’s destination IPv6 address. Gateway Identifies whether the route is directly connected and on which interface the route is configured. Dist/Metric Identifies if the route has a specified distance or metric.
PAGE 818
trust ipv6-diffserv Allows the dynamic classification of IPv6 DSCP. Syntax trust ipv6-diffserv To remove the definition, use the no trust ipv6-diffserv command. Defaults none Command Modes CONFIGURATION-POLICY-MAP-IN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 819
27 Intermediate System to Intermediate System (ISIS) IS-IS is an interior gateway protocol that uses shortest-path-first algorithm. IS-IS facilitates the communication between open systems, supporting routers passing through both IP and OSI traffic. A router is considered as an intermediate system. Networks are partitioned into manageable routing domains called areas. Intermediate systems send, receive, and forward packets to other routers within their area (Level 1 and Level 1-2 devices).
PAGE 820
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. To perform protocol-support consistency checks on hello packets, use this command. The adjacency-check is enabled by default. If a BFD session goes down indicating that IPv4 or IPv6 connectivity to its neighbor is lost, it does not imply that the adjacency is lost altogether. The hello adjacency runs over Layer 2, and does not require IP connectivity.
PAGE 821
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Version 6.3.1.0 Introduced You cannot disable leaking from Level 1 to Level 2. Also, you cannot enable leaking from Level 2 to Level 1. However, you can regulate the rate flow from one level to another using an IP Prefix list.
PAGE 822
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within an area. The configured password injects into Level 1 LSPs, CSNPs, and PSNPs. Related Commands • domain-password — allows you to set the authentication password for a routing domain.
PAGE 823
clear isis Restart the IS-IS process. All IS-IS data is cleared. Syntax Parameters clear isis [vrf vrf-name] [tag] {* | database | traffic} vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to restart the IS-IS process corresponding to that VRF. tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process.
PAGE 824
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 825
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. Entering debug isis enables all debugging parameters. To display all debugging information in one output, use this command. To turn off debugging, you normally enter separate no forms of each command. To disable all debug messages for IS-IS at once, enter the no debug isis command. debug isis adj-packets Enable debugging on adjacency-related activity such as hello packets that are sent and received on IS-IS adjacencies.
PAGE 826
Version Description 8.3.12.0 Introduced on the S4810. debug isis local-updates To debug IS-IS local update packets, enable debugging on a specific interface and provides diagnostic information. Syntax debug isis [vrf vrf-name] local-updates [interface] To turn off debugging, use the no debug isis [vrf vrf—name] updates [interface] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable the debugging information on IS-IS corresponding to that VRF.
PAGE 827
debug isis snp-packets To debug IS-IS complete sequence number PDU (CSNP) and partial sequence number PDU (PSNP) packets, enable debugging on a specific interface and provides diagnostic information. Syntax debug isis [vrf vrf-name] snp-packets [interface] To turn off debugging, use the no debug isis [vrf vrf-name] snp-packets [interface] command.
PAGE 828
debug isis spf-triggers Enable debugging on the events that triggered IS-IS shortest path first (SPF) events for debugging purposes. Syntax debug isis [vrf vrf-name] spf-triggers To turn off debugging, use the no debug isis [vrf vrf-name] spf-triggers command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to enable debugging information on IS-IS corresponding to that VRF. This information contains SPF trigger detail tied to the VRF that you specify.
PAGE 829
interface (OPTIONAL) Identifies the interface type slot/port as one of the following: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 830
Command Modes Command History • ROUTER ISIS (for IPv4) • CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 831
Command Modes Command History Related Commands ROUTER ISIS Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. pre-7.7.1.0 Introduced. router isis — Enter ROUTER mode on the switch.
PAGE 832
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 6.3.1.0 Introduced. The administrative distance indicates the trust value of incoming packets. A low administrative distance indicates a high trust rate. A high value indicates a lower trust rate.
PAGE 833
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. • distribute-list out — suppresses networks from being advertised in updates. • redistribute — redistributes routes from one routing domain to another routing domain.
PAGE 834
Usage Information Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 7.5.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced.
PAGE 835
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 7.8.1.0 Added IPv6 ISIS support. 6.3.1.0 Introduced. When you execute this command, IS-IS does not download the route to the routing table if the same route was redistributed into IS-IS routing protocol on the same router. domain-password Set the authentication password for a routing domain. Syntax domain-password [hmac-md5 | encryption-type] password To disable the password, use the no domain-password command.
PAGE 836
Related Commands • area-password — configures an IS-IS area authentication password. • isis priority — configures the authentication password for an interface. graceful-restart ietf Enable graceful restart on an IS-IS router. Syntax graceful-restart ietf To return to the default, use the no graceful-restart ietf command. Parameters ietf Enter ietf to enable graceful restart on the IS-IS router. Defaults Graceful restart disabled.
PAGE 837
graceful-restart interval Set the graceful restart grace period, the time during that all graceful restart attempts are prevented. Syntax graceful-restart interval minutes To return to the default, use the no graceful-restart interval command. Parameters minutes Enter the graceful-restart interval minutes. The range is from 1 to 20 minutes. The default is 5 minutes. Defaults 5 minutes Command Modes ROUTER ISIS Command History This guide is platform-specific.
PAGE 838
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 839
Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series. graceful-restart t2 Configure the wait time for the graceful restart timer T2 that a restarting router uses as the wait time for each database to synchronize.
PAGE 840
graceful-restart t3 Configure the overall wait time before graceful restart completes. Syntax graceful-restart t3 {adjacency | manual} seconds To return to the default, use the no graceful-restart t3 command. Parameters adjacency Enter the keyword adjacency so that the restarting router receives the remaining time value from its peer and adjusts its T3 value so if you have configured this option. manual Enter the keyword manual to specify a time value that the restarting router uses.
PAGE 841
hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-topoint hello PDUs. Syntax hello padding [multi-point | point-to-point] To return to the default, use the no hello padding [multi-point | point-to-point] command. Parameters multi-point (OPTIONAL) Enter the keywords multi-point to pad only LAN hello PDUs. point-to-point (OPTIONAL) Enter the keywords point-to-point to pad only point-to-point PDUs.
PAGE 842
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 843
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. IS-IS normally purges LSPs with an incorrect data link checksum causing the LSP source to regenerate the message. A cycle of purging and regenerating LSPs can occur when a network link continues to deliver accurate LSPs even though there is a link causing data corruption. This process could cause disruption to your system operation.
PAGE 844
Related Commands • net — configures an IS-IS network entity title (NET) for the routing process. • router isis — enables the IS-IS routing protocol. ipv6 router isis Enable the IPv6 IS-IS routing protocol and specify an IPv6 IS-IS process. Syntax ipv6 router isis [tag] To disable IS-IS routing, use the no router isis [tag] command. Parameters tag (OPTIONAL) This parameter is a unique name for a routing process. A null tag is assumed if the tag option is not specified.
PAGE 845
isis circuit-type Configure the adjacency type on interfaces. Syntax isis circuit-type {level-1 | level-1-2 | level-2-only} To return to the default values, use the no isis circuit-type command. Parameters level-1 You can form a Level 1 adjacency if there is at least one common area address between this system and neighbors. You cannot form Level 2 adjacencies on this interface.
PAGE 846
isis csnp-interval Configure the IS-IS complete sequence number PDU (CSNP) interval on an interface. Syntax isis csnp-interval seconds [level-1 | level-2] To return to the default values, use the no isis csnp-interval [seconds] [level-1 | level-2] command. Parameters seconds Interval of transmission time between CSNPs on multi-access networks for the designated intermediate system. The range is from 0 to 65535. The default is 10.
PAGE 847
To return to the default values, use the no isis hello-interval [seconds] [level-1 | level-2] command. Parameters seconds Allows you to set the length of time between hello packet transmissions. The range is from 1 to 65535. The default is 10. level-1 (OPTIONAL) Select this value to configure the hello interval for Level 1. This value is the default. level-2 (OPTIONAL) Select this value to configure the hello interval for Level 2.
PAGE 848
Parameters multiplier Specifies an integer that sets the multiplier for the hello holding time. Never configure a hello-multiplier lower than the default (3). The range is from 3 to 1000. The default is 3. level-1 (OPTIONAL) Select this value to configure the hello multiplier independently for Level 1 adjacencies. This value is the default. level-2 (OPTONAL) Select this value to configure the hello multiplier independently for Level 2 adjacencies.
PAGE 849
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 850
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Introduced on the E-Series. Dell Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics. isis metric Assign a metric to an interface.
PAGE 851
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Dell Networking recommends configuring metrics on all interfaces. Without configuring this command, the IS-IS metrics are similar to hop-count metrics.
PAGE 852
isis password Configure an authentication password for an interface. Syntax isis password [hmac-md5] password [level-1 | level-2] To delete a password, use the no isis password [password] [level-1 | level-2] command. Parameters encryption-type (OPTIONAL) Enter 7 to encrypt the password using DES. hmac-md5 (OPTIONAL) Enter the keywords hmac-md5 to encrypt the password using MD5. password Assign the interface authentication password.
PAGE 853
isis priority Set the priority of the designated router you select. Syntax isis priority value [level-1 | level-2] To return to the default values, use the no isis priority [value] [level-1 | level-2] command. Parameters value This value sets the router priority. The higher the value, the higher the priority. The range is from 0 to 127. The default is 64. level-1 (OPTIONAL) Specify the priority for Level 1. This setting is the default. level-2 (OPTIONAL) Specify the priority for Level 2.
PAGE 854
To return to the default values, use the no is-type command. Parameters level-1 Allows a router to act as a Level 1 router. level-1-2 Allows a router to act as both a Level 1 and Level 2 router. This setting is the default. level-2-only Allows a router to act as a Level 2 router. Defaults level-1-2 Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 855
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000.
PAGE 856
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. LSP throttling slows down the frequency at which LSPs are generated during network instability.
PAGE 857
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. The link MTU and the LSP MTU size must be the same.
PAGE 858
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 7.5.1.0 Added support for LSP Throttling Enhancement. The refresh interval determines the rate at which route topology information is transmitted preventing the information from becoming obsolete. The refresh interval must be less than the LSP lifetime specified with the max-lsp-lifetime command.
PAGE 859
Usage Information To configure the number of area addresses on router, use this command. This value must be consistent with routers in the same area, otherwise the router forms only Level 2 adjacencies. The value must be same among all the routers to form Level 1 adjacencies. max-lsp-lifetime Set the maximum time that link-state packets (LSPs) exist without being refreshed. Syntax max-lsp-lifetime seconds To restore the default time, use the no max-lsp-lifetime command.
PAGE 860
maximum-paths Allows you to configure the maximum number of equal cost paths allowed in a routing table. NOTE: Enables you to configure a single system wide value that is common for both IPv4 and IPv6 addresses. Syntax maximum-paths number To return to the default values, use the no maximum-paths command. Parameters Defaults number Enter a number as the maximum number of parallel paths an IP routing installs in a routing table. The range is from 1 to 64. The default is 4.
PAGE 861
Parameters narrow Allows you to generate and accept old-style TLVs. The metric range is from 0 to 63. transition Allows you to generate both old-style and new-style TLVs. The metric range is from 0 to 63. wide Allows you to generate and accept only new-style TLVs. The metric range is from 0 to 16777215. level-1 Enables the metric style on Level 1. level-2 Enables the metric style on Level 2. Defaults narrow; if no Level is specified, Level-1 and Level-2 are configured.
PAGE 862
Parameters transition Defaults Disabled Command Modes CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.
PAGE 863
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. passive-interface Suppress routing updates on an interface. This command stops the router from sending updates on that interface.
PAGE 864
Usage Information Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Although the passive interface does not send nor receive routing updates, the network on that interface is still included in the IS-IS updates sent using other interfaces. redistribute Redistribute routes from one routing domain to another routing domain.
PAGE 865
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 866
To return to the default values, use the no redistribute bgp command with the appropriate parameters. Parameters AS number Enter a number that corresponds to the autonomous system number. The range is from 1 to 65355. level-1 (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 routes only. level-1-2 (OPTIONAL) Routes are independently redistributed into IS-IS Level 1 and Level 2 routes. level-2 (OPTIONAL) Routes are independently redistributed into IS-IS as Level 2 routes only.
PAGE 867
Version Description 6.3.1.0 Introduced. Usage Information BGP to IS-IS redistribution supports “match” options using route maps. You can set the metric value, level, and metric-type of redistributed routes by the redistribution command. You can “set” more advanced options using route maps.
PAGE 868
route-map mapname map-name is an identifier for a configured route map. The route map should filter imported routes from the source routing protocol to the current routing protocol. If you do not specify a map-name, all routes are redistributed. If you specify a keyword, but fail to list route map tags, no routes are imported. Defaults Refer to Parameters.
PAGE 869
Parameters vrf vrf-name Enter the keyword vrf followed by the name of the VRF to enable the IS-IS routing protocol and to specify an IP IS-IS process on that VRF. tag (OPTIONAL) This is a unique name for a routing process. A null tag is assumed if the tag option is not specified. The tag name must be unique for all IP router processes for a given router. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 870
• Command History CONFIGURATION-ROUTER-ISIS-ADDRESS-FAMILY-IPV6 (for IPv6) This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500.
PAGE 871
Example (RouterIsis) Version Description 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. The bold section identifies that Multi-Topology IS-IS is enabled in Transition mode. Dell(conf-router_isis)#show config ! router isis clns host ISIS 49.0000.0001.F100.E120.0013.00 log-adjacency-changes net 49.0000.0001.F100.E120.0013.
PAGE 872
Command Modes Command History local (OPTIONAL) Displays local link-state database information. detail (OPTIONAL) Displays the detailed link-state database information of each LSP when specified. If not specified, a summary displays. summary (OPTIONAL) Displays the summary of link-state database information when specified. lspid (OPTIONAL) Display only the specified LSP. system-id (OPTIONAL) Displays the link-state database for system-id.
PAGE 873
Field Description An * after the LSPID indicates that the system originates an LSP where this command was issued. Example LSP Seq Num This value is the sequence number for the LSP that allows other systems to determine if they have received the latest information from the source. LSP Checksum This is the checksum of the entire LSP packet. LSP Holdtime This value is the amount of time, in seconds, that the LSP remains valid.
PAGE 874
IPv6 Address: 1011::1 Topology: IPv4 (0x00) IPv6 (0x8002) Metric: 10 IS OSPF.00 Metric: 10 IS (MT-IPv6) OSPF.00 Metric: 10 IP 10.1.1.0 255.255.255.0 Metric: 10 IP 15.1.1.0 255.255.255.0 Metric: 20 IP 10.3.3.0 255.255.255.
PAGE 875
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.1.0 Introduced on the E-Series.
PAGE 876
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. Dell#show isis hostname System Id Dynamic Name Static Name *F100.E120.0013 Force10 ISIS Dell# show isis interface Display detailed IS-IS interface status and configuration information.
PAGE 877
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. Dell>show isis int GigabitEthernet 1/7 is up, line protocol is up MTU 1497, Encapsulation SAP Routing Protocol: IS-IS Circuit Type: Level-1-2 Interface Index 37847070, Local circuit ID 1 Level-1 Metric: 10, Priority: 64, Circuit ID: systest-3.
PAGE 878
• Command Modes Command History • EXEC • EXEC Privilege For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.
PAGE 879
Hold Time: 28 Link Local Address: fe80::201:e8ff:fe00:492c Topology: IPv4 IPv6 , Common (IPv4 IPv6 ) Adjacency being used for MTs: IPv4 IPv6 Dell# show isis protocol Display IS-IS routing information. Syntax Parameters Command Modes Command History show isis [vrf vrf-name] protocol vrf vrf-name • EXEC • EXEC Privilege (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display ISIS routing information corresponding to that VRF. This guide is platform-specific.
PAGE 880
Accept narrow metrics: level-1-2 Generate wide metrics: none Accept wide metrics: none Multi Topology Routing is enabled in transition mode. Dell# show isis traffic This command allows you to display IS-IS traffic interface information. Syntax show isis [vrf vrf-name] traffic [interface] Parameters Command Modes Command History vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display ISIS traffic interface information corresponding to that VRF.
PAGE 881
Example Item Description Level-1/Level-2 Hellos (sent/rcvd) Displays the number of Hello packets sent and received. PTP Hellos (sent/ rcvd) Displays the number of point-to-point Hellos sent and received. Level-1/Level-2 LSPs sourced (new/refresh) Displays the number of new and refreshed LSPs. Level-1/Level-2 LSPs flooded (sent/rcvd) Displays the number of flooded LSPs sent and received. Level-1/Level-2 LSPs CSNPs (sent/ rcvd) Displays the number of CSNP LSPs sent and received.
PAGE 882
spf-interval Specify the minimum interval between shortest path first (SPF) calculations. Syntax spf-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] To restore default values, use the no spf-interval [level-l | level-2] interval seconds [initial_wait_interval seconds [second_wait_interval seconds]] command. Parameters Defaults level-l (OPTIONAL) Enter the keyword level-1 to apply the configuration to Level-1 SPF calculations.
PAGE 883
SPF throttling slows down the frequency at which route calculations are performed during network instability. Even though throttling route calculations slows down network convergence, not throttling can result in a network not functioning as expected. If network topology is unstable, throttling slows down the scheduling of route calculations until the topology regains its stability.
PAGE 884
28 Link Aggregation Control Protocol (LACP) This chapter contains commands for Dell Networks’s implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell Networking operating software. NOTE: For static LAG commands, refer to Port Channel Commands in the Interfaces chapter), based on the standards specified in the IEEE 802.
PAGE 885
Related Commands Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. show lacp — displays the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). Syntax debug lacp [config | events | pdu [interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pdu [interface-type [in | out]]] command. Parameters config (OPTIONAL) Enter the keyword config to debug the LACP configuration.
PAGE 886
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. lacp long-timeout Configure a long timeout period (30 seconds) for an LACP session.
PAGE 887
Usage Information This command applies to dynamic port-channel interfaces only. When applied on a static port-channel, this command has no effect. Related Commands show lacp — displays the LACP configuration. lacp port-priority To influence which ports will be put in Standby mode when there is a hardware limitation that prevents all compatible ports from aggregating, configure the port priority.
PAGE 888
lacp system-priority Configure the LACP system priority. Syntax lacp system-priority priority-value Parameters priority-value Enter the port-priority value. The higher the value number, the lower the priority. The range is from 1 to 65535. The default is 32768. Defaults 32768 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 889
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 890
Example (PortChannel-Number) Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 891
29 Layer 2 This chapter describes commands to configure Layer 2 features. MAC Addressing Commands The following commands are related to configuring, managing, and viewing MAC addresses. clear mac-address-table Clear the MAC address table of all MAC address learned dynamically. Syntax Parameters clear mac-address-table {dynamic | sticky }{address mac-address | all | interface interface | vlan vlan-id} dynamic Enter the keyword dynamic to specify dynamically-learned MAC addresses.
PAGE 892
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for sticky MAC addresses. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. mac-address-table aging-time Specify an aging time for MAC addresses to remove from the MAC address table.
PAGE 893
Related Commands Version Description pre-6.2.1.1 Introduced on the E-Series. mac learning-limit — sets the MAC address learning limits for a selected interface. show mac-address-table aging-time — displays the MAC aging time. mac-address-table static Associate specific MAC or hardware addresses to an interface and VLANs.
PAGE 894
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for output range parameter for S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.
PAGE 895
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. For details about using this command, refer to the “NIC Teaming” section of the Layer 2 chapter in the Dell Networking OS Configuration Guide.
PAGE 896
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Deprecated the no-station-move command (replaced by the maclearning-limit mac-address-sticky command). 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the vlan option on the E-Series. 8.2.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. Added the station-move option. 6.5.1.0 Added support for MAC Learning-Limit on the LAG.
PAGE 897
Parameters log Enter the keyword log to generate a syslog message on a learning-limit violation. shutdown Enter the keyword shutdown to shut down the port on a learning-limit violation. Defaults none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 898
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810.
PAGE 899
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the S-Series. 7.8.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Usage Information This command is supported on physical interfaces, static LAGs, and LACP LAGs.
PAGE 900
Version Description 7.5.1.0 Introduced on the E-Series. show cam mac linecard (count) Display the content addressable memory (CAM) size and the portions allocated for MAC addresses and for MAC ACLs. Syntax show cam mac linecard slot port-set port-pipe count [vlan vlan-id] [interface interface] Parameters linecard slot (REQUIRED) Enter the keyword linecard then a slot number to select the linecard for which to gather information.
PAGE 901
show cam mac linecard (dynamic or static) Display the CAM size and the portions allocated for MAC addresses and for MAC ACLs. Syntax Parameters Command Modes Command History show cam mac linecard slot port-set port-pipe [address mac_addr | dynamic | interface interface | static | vlan vlan-id] linecard slot (REQUIRED) Enter the keyword linecard then a slot number to select the linecard for which to gather information.
PAGE 902
Example Version Description 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 903
Command Modes Command History • For a port channel interface, enter the keywords port-channel then a number. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 904
Column Heading Description Type Lists whether the MAC address was manually configured (Static), learned dynamically (Dynamic), or associated with a specific port (Sticky). Interface Displays the interface type and slot/port information. The following abbreviations describe the interface types: State Example • gi — Gigabit Ethernet then a slot/port. • po — Port Channel then a number. The range is from 1 to 255 for TeraScale. • te — 10 Gigabit Ethernet then a slot/port.
PAGE 905
Static Address (User-defined) Count : 0 Sticky Address Count : 0 Total Synced Mac from Peer(N): 100 Total MAC Addresses in Use: 110 Dell# Related Commands show mac-address-table aging-time — displays MAC aging time. show mac-address-table aging-time Display the aging times assigned to the MAC addresses on the switch.
PAGE 906
show mac accounting destination Display destination counters for Layer 2 traffic (available on physical interfaces only). Syntax show mac accounting destination [mac-address vlan vlan-id] [interface interface [mac-address vlan vlan-id] [vlan vlan-id]] [vlan vlan-id] Parameters mac-address (OPTIONAL) Enter the MAC address in the nn:nn:nn:nn:nn:nn format to display information on that MAC address.
PAGE 907
00:44:00:00:00:01 00:22:00:00:00:00 00:44:00:00:00:02 00:44:00:00:00:01 Gi Gi Gi Gi 11/1 11/1 11/1 11/1 1000 1000 2000 2000 10000 10000 10000 10000 5120000 5120000 5120000 5120000 Dell-1# Related Commands show mac accounting access-list — displays the MAC access list configurations and counters (if configured). show mac learning-limit Display MAC address learning limits set for various interfaces.
PAGE 908
Example Version Description 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Added support for the violate-action and detail options. 6.5.1.0 Added support for Port Channel.
PAGE 909
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 910
Usage Information The no default vlan disable command is not listed in the running-configuration, but when the default VLAN is disabled, default-vlan disable is listed in the running-configuration. name Assign a name to the VLAN. Syntax name vlan-name To remove the name from the VLAN, use the no name command. Parameters vlan-name Enter up to 32 characters as the name of the VLAN. Defaults Not configured. Command Modes INTERFACE VLAN Command History This guide is platform-specific.
PAGE 911
show config Display the current configuration of the selected VLAN. Syntax show config Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 912
• Command Modes Command History IP address id vlan-id (OPTIONAL) Enter the keyword id then a number from 1 to 4094. Only information on the VLAN specified is displayed. name vlan-name (OPTIONAL) Enter the keyword name then the name configured for the VLAN. Only information on the VLAN named is displayed. • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 913
Column Heading Description Q Ports Example • Displays G for GVRP tagged • M for member of a VLAN-Stack VLAN • T for tagged interface • U for untagged interface • x (not capitalized x) for Dot1x untagged • X (capitalized X) for Dot1x tagged • o (not capitalized o) for OpenFlow untagged • O (capitalized O) for OpenFlow tagged • H for VSN tagged • i (not capitalized i) for Internal untagged • I (capitalized I) for Internal tagged • v (not capitalized v) for VLT untagged • V (capital
PAGE 914
Example (VLAN ID) Dell# show vlan id 40 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 40 Status Description Q Ports Active M Gi 13/47 Dell#show vlan id 41 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs Untagged, T - Tagged Dot1x untagged, X - Dot1x tagged GVRP tagged, M - Vlan-stack NUM 41 Status Description Q Ports Active T Gi 13/47 Dell#show vlan id 42 Codes: Q: U x G - * - Default VLAN, G - GVRP VLANs
PAGE 915
tagged Add a Layer 2 interface to a VLAN as a tagged interface. Syntax tagged interface To remove a tagged interface from a VLAN, use the no tagged interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a port channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 916
Tagged interfaces can belong to multiple VLANs, while untagged interfaces can only belong to one VLAN at a time. Related Commands interface vlan — configures a VLAN. untagged — specifies which interfaces in a VLAN are untagged. track ip Track the Layer 3 operational state of a Layer 3 VLAN, using a subset of the VLAN member interfaces. Syntax track ip interface To remove the tracking feature from the VLAN, use the no track ip interface command.
PAGE 917
Usage Information Version Description pre-6.2.1.1 Introduced on the E-Series. When this command is configured, the VLAN is operationally UP if any of the interfaces specified in the track ip command are operationally UP, and the VLAN is operationally DOWN if none of the tracking interfaces are operationally UP. If the track ip command is not configured, the VLAN's Layer 3 operational state depends on all the members of the VLAN.
PAGE 918
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series. Untagged interfaces can only belong to one VLAN. In the Default VLAN, you cannot use the no untagged interface command.
PAGE 919
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 920
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 921
Version Description 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Usage Information Related Commands FEFD disable command on the interface prevents the interface from running FEFD when FEFD is enabled globally. • fefd reset — clears an interface in Err-disabled state. It doesn’t work until the interface is in err-disabled state. • fefd mode — changes FEFD mode on an interface. fefd interval Set an interval between control packets.
PAGE 922
fefd mode Change the FEFD mode on an interface. Syntax fefd mode {normal | aggressive}] To return the FEFD mode to the default of normal, use the no fefd mode command. Parameters normal (OPTIONAL) Enter the keyword normal to change the link state to “unknown” when a far-end failure the software detects on that interface. When the interface is placed in “unknown” state, the software brings down the line protocol.
PAGE 923
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 924
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. Legacy E-Series command. Related Commands • fefd — enables far-end failure detection. • fefd-global — enables FEFD globally on the system. fefd-global Enable FEFD globally on the system.
PAGE 925
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. Legacy E-Series command. Usage Information If you enter only the fefd-global syntax, the mode is normal and the default interval is 15 seconds. If you disable FEFD globally (no fefd-global), the system does not remove the FEFD interface configuration. Related Commands • fefd — enables far-end failure detection.
PAGE 926
Version Description 8.3.12.0 Introduced on the S4810. Legacy E-Series command. Usage Information Example The following describes the show fefd command shown in the following example. Field Description Interface Displays the interfaces type and number. Mode Displays the mode (aggressive or normal) or NA if the interface contains fefd reset in its configuration. Interval Displays the interval between FEFD packets.
PAGE 927
30 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN. LLDP facilitates multi-vendor interoperability by using standard management tools to discover and make available a physical topology for network management. The Dell Networking operating software implementation of LLDP is based on IEEE standard 801.1ab.
PAGE 928
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. Added the vlan-name option. 7.6.1.
PAGE 929
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. advertise management-tlv Advertise management TLVs (Type, Length, Value).
PAGE 930
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. The command options management-address,system-capabilities, system-description, and system-name can be invoked individually or together, in any sequence. advertise management-tlv (Interface) Advertise management type, length, values (TLVs) to the specified interface.
PAGE 931
clear lldp counters Clear LLDP transmitting and receiving counters for all physical interfaces or a specific physical interface. Syntax Parameters clear lldp counters interface interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 932
Defaults none Command Modes EXEC Privilege Command History • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 933
packet (OPTIONAL) Enter the keyword packet to display information regarding packets coming in or going out. brief (OPTIONAL) Enter the keyword brief to display brief packet information. detail (OPTIONAL) Enter the keyword detail to display detailed packet information. tx (OPTIONAL) Enter the keyword tx to display transmit-only packet information. rx (OPTIONAL) Enter the keyword rx to display receive-only packet information.
PAGE 934
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 935
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. management-interface Enable and configure LLDP protocol parameters on the management interface.
PAGE 936
To return to the default, use the no mode {tx | rx} command. Parameters tx Enter the keyword tx to set the mode to transmit. rx Enter the keyword rx to set the mode to receive. Defaults Both transmit and receive. Command Modes CONFIGURATION (conf-lldp) and INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 937
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 938
Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. protocol lldp (Interface) Enter the LLDP protocol in INTERFACE mode. Syntax [no] protocol lldp To return to the global LLDP configuration mode, use the no protocol lldp command from Interface mode. Defaults LLDP is not enabled on the interface. Command Modes INTERFACE (conf-if-interface-lldp) Command History This guide is platform-specific.
PAGE 939
show lldp neighbors Display LLDP neighbor information for all interfaces or a specified interface. Syntax Parameters show lldp neighbors [interface] [detail] interface detail (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 940
show lldp statistics Display the LLDP statistical information. Syntax show lldp statistics Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 941
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2.(0.0) Introduced on the Z9000 and S4810. show running-config lldp Display the current global LLDP configuration. Syntax show running-config lldp Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 942
LLDP-MED Commands The following are the LLDP-MED (Media Endpoint Discovery) commands. Dell Networking OS LLDP-MED commands are an extension of the set of LLDP TLV advertisement commands. The C-Series and SSeries support all commands. The E-Series generally supports the commands. However, LLDP-MED commands are more useful on the C-Series and the S50V model of the S-Series, because they support Power over Ethernet (PoE) devices.
PAGE 943
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. protocol lldp (Configuration) — enables LLDP globally.
PAGE 944
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP.
PAGE 945
Usage Information Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series.
PAGE 946
Version Description 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. Usage Information Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors.
PAGE 947
Related Commands Version Description 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med streaming-video To advertise streaming video services for broadcast or multicast-based video, configure the system. This command does not include video applications that rely on TCP buffering.
PAGE 948
Related Commands Version Description 7.6.1.0 Introduced on the C-Series and E-Series. debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med video-conferencing To advertise dedicated video conferencing and other similar appliances that support real-time interactive video, configure the system.
PAGE 949
Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med video-signaling To advertise video control packets that use a separate network policy than video data, configure the system. Syntax advertise med video-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med video-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command.
PAGE 950
advertise med voice To advertise a dedicated IP telephony handset or other appliances supporting interactive voice services, configure the system. Syntax advertise med voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med voice {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 951
advertise med voice-signaling To advertise when voice control packets use a separate network policy than voice data, configure the system. Syntax advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} To return to the default, use the no advertise med voice-signaling {vlan-id layer2_priority DSCP_value} | {priority-tagged number} command. Parameters vlan-id Enter the VLAN ID. The range is from 1 to 4094.
PAGE 952
31 Microsoft Network Load Balancing Network Load Balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. Microsoft NLB clustering allows multiple servers running Microsoft Windows to be represented by one MAC and one IP address to provide transparent failover and load-balancing.
PAGE 953
• vlan vlan-id For a port channel interface, enter the keywords port-channel then a number. Enter the keyword vlan then a VLAN ID number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History The following is a list of the Dell Networking OS version history for this command. Example (Multicast) Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.3(0.0) Added support for multicast MAC address on the MXL platform.
PAGE 954
32 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM Sparse-Mode (PIM-SM) domains together. MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are received. MSDP connections are parallel with MBGP connections. The Dell Networking operating system supports MSDP commands on the S3048–ON platform.
PAGE 955
clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax Parameters clear ip msdp sa-cache [group-address | rejected-sa | local] group-address Enter the group IP address in dotted decimal format (A.B.C.D.).
PAGE 956
clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. Syntax clear ip msdp statistic peer peer-address Parameters peer Enter the keyword peer to clear the MSDP peer entries. peer-address Enter the IP address of the MSDP peer. Defaults Without any options, this command clears the entire source-active cache. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 957
Parameters event peer address Enter the keyword event then the peer address in a dotted decimal format (A.B.C.D.). packet peer address Enter the keyword packet then the peer address in a dotted decimal format (A.B.C.D.). pim Enter the keyword pim to debug advertisement from PIM. Defaults Not configured. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 958
The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.4.1.
PAGE 959
Usage Information Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added the list option and removed the prefix-list option. 7.4.1.0 Introduced If a list is not specified, all SA messages received from the default peer are accepted. You can enter multiple default peer commands. ip msdp log-adjacency-changes Enable logging of MSDP adjacency changes.
PAGE 960
ip msdp mesh-group To be a member of a mesh group, configure a peer. Syntax ip msdp mesh-group {name} {peer address} To remove the peer from a mesh group, use the no ip msdp mesh-group {name} {peer address} command. Parameters name Enter a string of up to 16 characters long for as the mesh group name. peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 961
To remove the originator-id, use the no ip msdp originator-id {interface} command. Parameters interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 962
Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.). connect-source interface Enter the keywords connect-source then one of the interfaces and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 963
If the total number of SA messages received from the peer is already larger than the limit when this command is applied, those SA messages continue to be accepted. To enforce the limit in such situation, use the clear ip msdp peer command to reset the peer. Related Commands ip msdp sa-limit — configures the MSDP SA Limit. clear ip msdp peer — clears the MSDP peer. show ip msdp — displays the MSDP information. ip msdp redistribute Filter local PIM SA entries in the SA cache.
PAGE 964
ip msdp sa-filter Permit or deny MSDP source active (SA) messages based on multicast source and/or group from the specified peer. Syntax ip msdp sa-filter {in | out} peer-address list [access-list name] Remove this configuration using the no ip msdp sa-filter {in | out} peer address list [access-list name] command. Parameters in Enter the keyword in to enable incoming SA filtering. out Enter the keyword out to enable outgoing SA filtering.
PAGE 965
To return to the default, use the no ip msdp sa-limit number command. Parameters number Enter the maximum number of SA entries in SA-cache. The range is from 1 to 500000. Defaults 50000 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 966
Parameters peer address Enter the peer address in a dotted decimal format (A.B.C.D.). Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 967
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 6.2.1.1 Introduced show ip msdp Display the MSDP peer status, SA cache, or peer summary. Syntax Parameters Defaults Command Modes Command History show ip msdp {peer peer address | sa-cache | summary} peer peer address Enter the keyword peer then the peer address in a dotted decimal format (A.B.C.D.).
PAGE 968
Example Dell#show ip msdp peer 100.1.1.1 Peer Addr: 100.1.1.1 Local Addr: 100.1.1.2(639) Connect Source: none State: Established Up/Down Time: 00:00:08 Timers: KeepAlive 60 sec, Hold time 75 sec SourceActive packet count (in/out): 0/0 SAs learned from this peer: 0 SA Filtering: Input (S,G) filter: none Output (S,G) filter: none Dell# Example (Sa-cache) Dell#show ip msdp sa-cache MSDP Source-Active Cache - 1 entries GroupAddr SourceAddr RPAddr 224.1.1.1 172.21.220.10 172.21.3.
PAGE 969
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 7.4.1.0 Introduced. Dell#show ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 200 rejected SAs UpTime GroupAddr SourceAddr RPAddr 00:00:13 225.1.2.1 10.1.1.3 110.1.1.1 00:00:13 225.1.2.2 10.1.1.4 110.1.1.1 00:00:13 225.1.2.3 10.1.1.3 110.1.1.1 00:00:13 225.1.2.4 10.1.1.4 110.1.1.1 00:00:13 225.1.2.5 10.1.1.3 110.1.1.1 00:00:13 225.1.2.6 10.1.1.4 110.1.1.1 00:00:13 225.1.2.7 10.1.1.3 110.1.1.
PAGE 970
33 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell Networking operating system, conforms to IEEE 802.1s. This command supports the Dell Networking S3048–ON platform. debug spanning-tree mstp Enable debugging of the multiple spanning tree protocol and view information on the protocol.
PAGE 971
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.1 Introduced on the E-Series.
PAGE 972
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.5.1.0 Introduced. protocol spanning-tree mstp — enters MULTIPLE SPANNING TREE mode. forward-delay The amount of time the interface waits in the Blocking State and the Learning State before transitioning to the Forwarding State.
PAGE 973
Related Commands Version Description 6.5.1.0 Introduced. max-age — changes the wait time before MSTP refreshes protocol configuration information. hello-time — changes the time interval between bridge protocol data units (BPDUs). hello-time Set the time interval between generation of MSTB bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command. Parameters seconds Enter a number as the time interval between transmission of BPDUs.
PAGE 974
max-age — changes the wait time before MSTP refreshes protocol configuration information. max-age To maintain configuration information before refreshing that information, set the time interval for the MSTB. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters max-age Enter a number of seconds the Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds.
PAGE 975
msti Configure multiple spanning tree instance, bridge priority, and one or multiple VLANs mapped to the MST instance. Syntax msti instance {vlan range | bridge-priority priority} To disable mapping or bridge priority, use the no msti instance {vlan range | bridgepriority priority} command. Parameters msti instance Enter the MSTP instance. The range is from zero (0) to 63. vlan range Enter the keyword vlan then the identifier range value. The range is from 1 to 4094.
PAGE 976
name The name you assign to the multiple spanning tree region. Syntax name region-name To remove the region name, use the no name command. Parameters region-name Enter the MST region name. The range is 32 character limit. Defaults no default name. Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 977
protocol spanning-tree mstp To enable and configure the multiple spanning tree group, enter MULTIPLE SPANNING TREE mode. Syntax protocol spanning-tree mstp To disable the multiple spanning tree group, use the no protocol spanning-tree mstp command. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 978
revision The revision number for the multiple spanning tree configuration. Syntax revision range To return to the default values, use the no revision command. Parameters range Enter the revision number for the MST configuration. The range is from 0 to 65535. The default is 0. Defaults 0 Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 979
show config View the current configuration for the mode. Only non-default values are shown. Syntax show config Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 980
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 981
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 982
Designated port id is 128.89, designated path cost Number of transitions to forwarding state 3 BPDU (Mrecords): sent 7, received 1103 The port is not in the portfast mode Example (EDS and LBK) The bold line shows the loopback BPDU inconsistency (LBK_INC). Dell#show spanning-tree msti 0 brief MSTI 0 VLANs mapped 1-4094 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32768, Address 0001.e801.
PAGE 983
Name Instance Sts Guard type -----------------------------------Gi 1/1 5 INCON(Root) Rootguard Gi 1/2 5 FWD Loopguard Gi 1/3 5 EDS(Shut) Bpduguard spanning-tree Enable the multiple spanning tree protocol on the interface. Syntax spanning-tree To disable the multiple spanning tree protocol on the interface, use the no spanning-tree command. Parameters spanning-tree Enter the keywords spanning-tree to enable the MSTP on the interface. Defaults Enable.
PAGE 984
spanning-tree msti Configure multiple spanning tree instance cost and priority for an interface. Syntax spanning-tree msti instance {cost cost | priority priority} Parameters msti instance Enter the keyword msti and the MST instance number. The range is from zero (0) to 63. cost cost (OPTIONAL) Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 985
Version Description 6.5.1.0 Introduced on the E-Series. tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 986
34 Multicast The multicast commands are supported by Dell Networking operating system (OS) on all S3048–ON platform. IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned multicast routes on the multicast forwarding table. To clear the protocol-independent multicast (PIM) tree information base, use the clear ip pim tib command.
PAGE 987
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. E-Series legacy command Related Commands show ip pim tib — shows the PIM tree information base. ip mroute Assign a static mroute.
PAGE 988
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 989
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series. 7.6.1.0 Introduced on the E-Series. This feature allows you to limit the number of multicast entries on the system. This number is the total of all the multicast entries on all line cards in the system. On each line card, the multicast module only installs the maximum number of entries, depending on the configured CAM profile. To store multicast routes, use the IN-L3-McastFib CAM partition.
PAGE 990
show ip mroute View the multicast routing table. Syntax show ip mroute [vrf vrf-name] [static | group-address [source-address] | count | snooping [vlan vlan-idIntroduced on the S6000-ON.] [group-address [source-address]] | summary | vlt [group-address [source-address] | count] Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure this setting on that VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 991
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2.(0.0) Added support for keyword vlt to the Z9000, S4810, and S4820T. 8.4.1.1 Support for the keyword snooping and the optional vlan vlan-id, groupaddress, and source-address parameters were added on E-Series ExaScale. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 992
Example Field Description (S, G) Displays the forwarding entry in the multicast route table. uptime Displays the amount of time the entry has been in the multicast forwarding table. Incoming interface Displays the reverse path forwarding (RPF) information towards the source for (S,G) entries and the RP for (*,G) entries.
PAGE 993
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. E-Series legacy command Usage Information Network administrators use static mroutes to control the reach-ability of the multicast sources.
PAGE 994
35 Neighbor Discovery Protocol (NDP) The neighbor discovery protocol for IPv6 is defined in RFC 2461 as part of the Stateless Address Autoconfiguration protocol. It replaces the Address Resolution Protocol used with IPv4.
PAGE 995
Command Modes Command History • EXEC • EXEC Privilege • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 996
hardware_address • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094.
PAGE 997
show ipv6 neighbors Display IPv6 discovery information. Entering the command without options shows all IPv6 neighbor addresses stored on the control processor (CP). Syntax Parameters show ipv6 neighbors [vrf vrf-name] [ipv6-address| interface interface] vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to display the neighbors corresponding to that VRF. NOTE: If you do not specify this option, neighbors corresponding to the default VRF are displayed.
PAGE 998
Example Version Description 8.3.7.1 Introduced on the S4810. Dell# show ipv6 neighbors IPv6 Address Expires(min) Hardware Address State Interface VLAN CPU --------------------------------------------------------------100::1 0.03 00:00:00:00:00:22 DELAY Gi 1/12 - CP fe80::200:ff:fe00:22 232 00:00:00:00:00:22 STALE Gi 1/12 - CP 500::1 0.60 00:01:e8:17:5c:af REACH Gi 1/13 - CP fe80::200:ff:fe00:17 232 00:00:00:00:00:29 REACH Gi 1/14 - CP 900::1 0.60 00:01:e8:17:5c:b1 STALE Po 23 - CP 400::1 0.
PAGE 999
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.9(0.0) Introduced on the Z9500. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches.
PAGE 1000
Parameters maximum limit Enter the keyword maximum then the hop limit value. The range is from 0 to 254. minimum limit Enter the keyword minimum then the hop limit value. The range is from 0 to 254. Defaults none Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1001
Related Commands show ipv6 nd ra-guard policy — Displays the configuration applied on all the RA guard policies or a specific RA guard policy. ipv6 nd ra-guard enable Allow you to configure the RA guard related commands. Syntax ipv6 nd ra-guard enable To disable the RA guard, use the no ipv6 nd ra-guard enable command. Defaults Disabled Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1002
managed-config-flag Set the managed address configuration flag. Syntax managed-config-flag {on | off} To clear the flag, use the no managed-config-flag {on | off} command. Parameters on Enter the keyword on to set the managed-config-flag value as ON. off Enter the keyword off to set the managed-config flag value as OFF. Defaults none Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific.
PAGE 1003
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.7(0.
PAGE 1004
other-config-flag Enable the verification of the advertised other configuration parameter. If this command is not configured, the verification process is bypassed. Syntax other-config-flag {on | off} To reset the other configuration parameter, use the no other-config-flag {on | off} command. Parameters on Enter the keyword on to set the other-config-flag value as ON. off Enter the keyword off to set the other-config flag value as OFF.
PAGE 1005
Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9000 switches. • ipv6 nd ra-guard enable — Allows you to configure the RA guard related commands. • ipv6 nd raguard policy policy-name — Defines the RA guard policy name and enter the RA guard policy configuration mode.
PAGE 1006
Defaults none Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.9(0.0) Introduced on the Z9500. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1007
Related Commands • ipv6 nd ra-guard enable — Allow you to configure the RA guard related commands. • ipv6 nd raguard policy policy-name — Defines the router advertisement (RA) guard policy name and enter the RA guard policy configuration mode. show config Display the RA guard policy mode configurations. Syntax show config Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific.
PAGE 1008
show ipv6 nd ra-guard policy Display the configurations applied on all the RA guard policies or a specific RA guard policy. Syntax show ipv6 nd ra-guard policy policy-name Parameter policy policy-name Enter the keyword policy then the policy name. The policy name allows a maximum of 140 characters. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1009
trusted-port Allow bypassing the configured RA guard validation and forwards the RA packets received on the interface, which has the trusted port policy attached. Syntax trusted-port To reset the policy applied to the trusted port, use the no trusted-port command. Defaults none Command Modes POLICY LIST CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1010
36 Object Tracking Object Tracking supports IPv4 and IPv6, and is available on the Dell Networking platforms. Object tracking allows you to define objects of interest, monitor their state, and report to a client when a change in an object’s state occurs.
PAGE 1011
Example Version Description 8.4.1.0 Introduced. Dell#debug track all 04:35:04: %RPM0-P:RP2 %OTM-5-STATE: track 6 - Interface GigabitEthernet 1/2 line-protocol DOWN 04:35:04: %RPM0-P:RP2 %OTM-5-NOTIF: VRRP notification: resource ID 6 DOWN delay Configure the time delay used before communicating a change in the status of a tracked object to clients. Syntax delay {[up seconds] [down seconds]} To return to the default setting, use the no delay command.
PAGE 1012
description Enter a description of a tracked object. Syntax description {text} To remove the description, use the no description {text} command. Parameters text Enter a description to identify a tracked object (80 characters maximum). Defaults none Command Modes OBJECT TRACKING (conf_track_object-id) Command History Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.
PAGE 1013
track 2 ipv6 route 2040::/64 metric threshold delay down 3 delay up 5 threshold metric up 200 track 3 ipv6 route 2050::/64 reachability track 4 interface GigabitEthernet 1/2 ip routing track 5 ip route 192.168.0.0/24 reachability vrf red track resolution ip route isis 20 track resolution ip route ospf 10 Example (Object-id) Dell#show running-config track 300 track 300 ip route 10.0.0.
PAGE 1014
Usage Information Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. The following describes the show track command shown in the Example below. Output Description Track object-id Displays the number of the tracked object.
PAGE 1015
Example (Brief) Related Commands Output Description State Up or Down state of the tracked object. Last Change Time since the last change in the state of the tracked object. Dell>show track brief ResId Resource Parameter State LastChange 1 IP route reachability 10.16.0.0/16 Up 00:01:08 2 Interface line-protocol Ethernet0/2 Down 00:05:00 3 Interface ip routing VLAN100 Up 01:10:05 • show running-config track – displays configuration information about tracked objects.
PAGE 1016
Determine the UP/DOWN state of a tracked route by the threshold for the current value of the route metric in the routing table. To provide a common tracking interface for different clients, route metrics are scaled in the range 0 to 255, where 0 is connected and 255 is inaccessible. The scaled metric value communicated to a client always considers a lower value to have priority over a higher value.
PAGE 1017
Command History Usage Information Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. Added support for tunnel interface. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced.
PAGE 1018
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the line-protocol state of a Layer 2 interface by monitoring its operational status (UP or DOWN). When the link-level status goes down, the tracked object status is considered to be DOWN; if the link-level status is up, the tracked object status is considered to be UP.
PAGE 1019
Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. ip-address/ prefixlen Enter an IPv4 address in dotted decimal format. The valid IPv4 prefix lengths are from /0 to /32. vrf vrf-name (Optional) E-Series only: You can configure a VPN routing and forwarding (VRF) instance to specify the virtual routing table to which the tracked route belongs. Defaults none Command Modes CONFIGURATION Command History Usage Information Version Description 9.8(0.
PAGE 1020
track ip route reachability Configure object tracking on the reachability of an IPv4 route. Syntax track object-id ip route ip-address/prefix-len reachability [vrf vrf-name] To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. ip-address/ prefixlen Enter an IPv4 address in dotted decimal format. The valid IPv4 prefix lengths are from /0 to /32.
PAGE 1021
track resolution ip route Configure the protocol-specific resolution value used to scale an IPv4 route metric. Syntax track resolution ip route {isis resolution-value | ospf resolution-value} To return to the default setting, use the no track object-id command. Parameters object-id Enter the ID number of the tracked object. The range is 1 to 500. isis resolution-value Enter the resolution used to convert the metric in the routing table for ISIS routes to a scaled metric.
PAGE 1022
IPv6 Object Tracking Commands The following section describes the IPv6 object tracking commands. The following object tracking commands apply to IPv4 and IPv6: • debug track • delay • description • show running-config track • threshold metric • track interface line-protocol show track ipv6 route Display information about all tracked IPv6 routes, including configuration, current tracked state (UP or DOWN), and the clients which are tracking an object.
PAGE 1023
Example Dell#show track ipv6 route Track 2 IPv6 route 2040::/64 metric threshold Metric threshold is Up (STATIC/0/0) 5 changes, last change 00:02:30 Metric threshold down 255 up 254 First-hop interface is GigabitEthernet 1/2 Tracked by: VRRP GigabitEthernet 2/4 IPv6 VRID 1 Track 3 IPv6 route 2050::/64 reachability Reachability is Up (STATIC) 5 changes, last change 00:02:30 First-hop interface is GigabitEthernet 1/2 Tracked by: VRRP GigabitEthernet 2/4 IPv6 VRID 1 Usage Command Example (Brief) The follow
PAGE 1024
Defaults none Command Modes CONFIGURATION Command History Usage Information Related Commands • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number.
PAGE 1025
Command History Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the UP and/or DOWN threshold of an IPv6 route metric. In order for a route’s metric to be tracked, the route must appear as an entry in the routing table.
PAGE 1026
ipv6-address/ prefix-len Defaults none Command Modes CONFIGURATION Command History Usage Information Enter an IPv6 address in X:X:X:X::X format. The valid IPv6 prefix lengths are from /0 to / 128. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to create an object that tracks the reachability of an IPv6 route.
PAGE 1027
Command Modes Command History Usage Information CONFIGURATION Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced. Use this command to configure the protocol-specific resolution value that converts the actual metric of an IPv6 route in the routing table to a scaled metric in the range 0 to 255.
PAGE 1028
37 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on platform. OSPF is an Interior Gateway Protocol (IGP), which means that it distributes routing information between routers in a single Autonomous System (AS). OSPF is also a link-state protocol in which all routers contain forwarding tables derived from information about their links to their neighbors.
PAGE 1029
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1030
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1031
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information Only the routes within an area are summarized, and that summary is advertised to other areas by the ABR.
PAGE 1032
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Usage Information To configure all routers and access servers within a stub, use this command.
PAGE 1033
Version Description 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. clear ip ospf Clear all OSPF routing tables. S3048–ON Syntax Parameters clear ip ospf process-id [process] process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared. process (OPTIONAL) Enter the keyword process to reset the OSPF process.
PAGE 1034
clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. S3048–ON Syntax clear ip ospf [process-id] [vrf vrf-name] statistics [interface name {neighbor router-id}] Parameters process-id Enter the OSPF Process ID to clear a specific process. If no Process ID is entered, all OSPF processes are cleared. vrf vrf-name Enter the keyword vrf followed by the name of the VRF to clear all OSPF routing tables corresponding to that VRF.
PAGE 1035
Related Commands Version Description 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. show ip ospf statistics — displays the OSPF statistics. debug ip ospf Display debug information on OSPF. Entering the debug ip ospf commands enables OSPF debugging for the first OSPF process.
PAGE 1036
Usage Information 1036 Version Description 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The following describes the debug ip ospf command shown in the Example below. Field Description 8:14 Displays the time stamp. OSPF Displays the OSPF process ID: instance ID. v: Displays the OSPF version. Dell Networking OS supports version 2 only.
PAGE 1037
Field Example Description • MC+ (bit used by MOSPF is set and router is able to forward IP multicast packets) • MC- (bit used by MOSPF is not set and router cannot forward IP multicast packets) • E + (router is able to accept AS External LSAs) • E - (router cannot accept AS External LSAs) • T + (router can support TOS) • T - (router cannot support TOS) hi: Displays the amount of time configured for the HELLO interval. di: Displays the amount of time configured for the DEAD interval.
PAGE 1038
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1039
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. description Add a description about the selected OSPF configuration. S3048–ON Syntax description description To remove the OSPF description, use the no description command.
PAGE 1040
Related Commands Version Description pre- 6.1.1.1 Introduced on the E-Series. show ip ospf asbr — displays the VLAN configuration. distance Define an administrative distance for particular routes to a specific IP address. S3048–ON Syntax distance weight [ip-address mask access-list-name] To delete the settings, use the no distance weight [ip-address mask access-list-name] command. Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110.
PAGE 1041
distance ospf Configure an OSPF distance metric for different types of routes. S3048–ON Syntax distance ospf [external dist3] [inter-area dist2] [intra-area dist1] To delete these settings, use the no distance ospf command. Parameters Defaults external dist3 (OPTIONAL) Enter the keyword external then a number to specify a distance for external type 5 and 7 routes. The range is from 1 to 255. The default is 110.
PAGE 1042
distribute-list in Apply a filter to incoming routing updates from OSPF to the routing table. S3048–ON Syntax distribute-list prefix-list-name in [interface] To delete a filter, use the no distribute-list prefix-list-name in [interface] command. Parameters prefix-list-name Enter the name of a configured prefix list. interface (OPTIONAL) Enter one of the following keywords and slot/port or number information: • For Port Channel groups, enter the keywords port-channel then a number.
PAGE 1043
distribute-list out To restrict certain routes destined for the local routing table after the SPF calculation, apply a filter. S3048–ON Syntax distribute-list prefix-list-name out [bgp | connected | isis | rip | static] To remove a filter, use the no distribute-list prefix-list-name out [bgp | connected | isis | rip | static] command. Parameters prefix-list-name Enter the name of a configured prefix list. bgp (OPTIONAL) Enter the keyword bgp to specify that BGP routes are distributed.
PAGE 1044
Usage Information Version Description 7.8.1.0 Added support for the Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. The distribute-list out command applies to routes autonomous system boundary routers (ASBRs) redistributes into OSPF. It can be applied to external type 2 and external type 1 routes, but not to intra-area and inter-area routes.
PAGE 1045
Generally, convergence level 1 meets most convergence requirements. Higher convergence levels should only be selected following consultation with Dell Networking technical support. graceful-restart grace-period Specifies the time duration, in seconds, that the router’s neighbors continue to advertise the router as fully adjacent regardless of the synchronization state during a graceful restart.
PAGE 1046
graceful-restart helper-reject Specify the OSPF router to not act as a helper during graceful restart. S3048–ON Syntax graceful-restart helper-reject ip-address To return to default value, use the no graceful-restart helper-reject command. Parameters ip-address Enter the OSPF router-id, in IP address format, of the restart router that will not act as a helper during graceful restart. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1047
Parameters planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplanned-only (OPTIONAL) Enter the keywords unplanned-only to indicate graceful restart is supported in an unplanned restart condition only. Defaults Support for both planned and unplanned failures. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1048
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0) Introduced on the S3048-ON and S4048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.
PAGE 1049
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ip ospf authentication-key Enable authentication and set an authentication key on OSPF traffic on an interface.
PAGE 1050
ip ospf cost Change the cost associated with the OSPF traffic on an interface. S3048–ON Syntax ip ospf cost cost To return to default value, use the no ip ospf cost command. Parameters cost Enter a number as the cost. The range is from 1 to 65535. Defaults The default cost is based on the reference bandwidth. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1051
To return to the default values, use the no ip ospf dead-interval command. Parameters seconds Enter the number of seconds for the interval. The range is from 1 to 65535. The default is 40 seconds. Defaults 40 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1052
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1053
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 9.1(0.0) Included usage information on maximum number of digest keys per interface. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. You can configure a maximum of six digest keys on an interface.
PAGE 1054
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. ip ospf network Set the network type for the interface. S3048–ON Syntax ip ospf network {broadcast | point-to-point} To return to the default, use the no ip ospf network command.
PAGE 1055
Version Description pre- 6.1.1.1 Introduced on the E-Series. ip ospf priority To determine the designated router for the OSPF network, set the priority of the interface. S3048–ON Syntax ip ospf priority number To return to the default setting, use the no ip ospf priority command. Parameters number Enter a number as the priority. The range is from 0 to 255. The default is 1. Defaults 1 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1056
ip ospf retransmit-interval Set the retransmission time between lost link state advertisements (LSAs) for adjacencies belonging to the interface. S3048–ON Syntax ip ospf retransmit-interval seconds To return to the default values, use the no ip ospf retransmit-interval command. Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600. The default is 5 seconds.
PAGE 1057
Parameters seconds Enter the number of seconds as the interval between retransmission. The range is from 1 to 3600. The default is 1 second. This value must be greater than the transmission and propagation delays for the interface. Defaults 1 second Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1058
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1059
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. network area Define which interfaces run OSPF and the OSPF area for those interfaces. S3048–ON Syntax network ip-address mask area area-id To disable an OSPF area, use the no network ip-address mask area area-id command.
PAGE 1060
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. To enable OSPF on an interface, the network area command must include, in its range of addresses, the primary IP address of an interface. NOTE: An interface can be attached only to a single OSPF area. If you delete all the network area commands for Area 0, the show ip ospf command output does not list Area 0.
PAGE 1061
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Modified to include the keyword default. pre- 6.1.1.1 Introduced on the E-Series.
PAGE 1062
• May update ABR status. On configuring suppression using the passive-interface command, the state of the OSPF neighbor does not change to INIT; instead, the state of the OSPF neighbor changes to DOWN after the dead-timer expires. redistribute Redistribute information from another routing protocol throughout the OSPF process.
PAGE 1063
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. To redistribute the default route (0.0.0.0/0), configure the default-information originate command.
PAGE 1064
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1065
metric-type typevalue (OPTIONAL) Enter the keywords metric-type then one of the following: • 1 = for OSPF External type 1 • 2 = for OSPF External type 2 route-map mapname (OPTIONAL) Enter the keywords route-map then the name of the route map. tag tag-value (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1066
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1067
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1(0.
PAGE 1068
Example Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. Dell(conf-router_ospf)#show config ! router ospf 3 passive-interface 0 GigabitEthernet 1/1 Dell(conf-router_ospf)# show ip ospf Display information on the OSPF process configured on the switch.
PAGE 1069
Usage Information Version Description 7.8.1.0 Added support of Multi-Process OSPF. 7.8.1.0 Added the process-id option, in support of Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre- 6.1.1.1 Introduced on the E-Series. If you delete all the network area commands for Area 0, the show ip ospf command output does not list Area 0. The following describes the show ip ospf command shown in the following example.
PAGE 1070
Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.
PAGE 1071
show ip ospf database Display all LSA information. If you do not enable OSPF on the switch, no output is generated. S3048–ON Syntax Parameters Command Modes Command History show ip ospf process-id [vrf vrf-name] database [database-summary] process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process.
PAGE 1072
Example Field Description Checksum Displays the Fletcher checksum of an LSA’s complete contents. Link count Displays the number of interfaces for that router. Dell>show ip ospf 1 database OSPF Router with ID (11.1.2.1) (Process ID 1) Router (Area 0.0.0.0) Link ID ADV Router Age Seq# Checksum 11.1.2.1 11.1.2.1 673 0x80000005 0x707e 13.1.1.1 13.1.1.1 676 0x80000097 0x1035 192.68.135.2 192.68.135.2 1419 0x80000294 0x9cbd Link ID 10.2.3.2 10.2.4.2 Link ID 0.0.0.0 1.1.1.1 10.1.1.0 10.1.2.0 10.2.2.0 10.2.
PAGE 1073
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1074
Example Field Description Metric Displays the LSA metric. Dell#show ip ospf 100 database asbr-summary OSPF Router with ID (1.1.1.10) (Process ID 100) Summary Asbr (Area 0.0.0.0) LS age: 1437 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 103.1.50.1 Advertising Router: 1.1.1.10 LS Seq Number: 0x8000000f Checksum: 0x8221 Length: 28 Network Mask: /0 TOS: 0 Metric: 2 LS age: 473 Options: (No TOS-capability, No DC, E) LS type: Summary Asbr Link State ID: 104.1.50.
PAGE 1075
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1076
Example Field Description Metric Displays the LSA metric. Forward Address Identifies the address of the forwarding router. Data traffic is forwarded to this router. If the forwarding address is 0.0.0.0, data traffic is forwarded to the originating router. External Route Tag Displays the 32-bit field attached to each external route. The OSPF protocol does not use this field, but you can use the field for external route management. Dell#show ip ospf 1 database external OSPF Router with ID (20.20.20.
PAGE 1077
adv-router ipaddress Command Modes Command History • EXEC • EXEC Privilege • the network’s IP address for Type 3 LSAs or Type 5 LSAs • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. This guide is platform-specific.
PAGE 1078
Example Field Description Advertising Router Identifies the router ID of the LSA’s originating router. Checksum Identifies the link state sequence number. This number enables you to identify old or duplicate LSAs. Length Displays the Fletcher checksum of an LSA’s complete contents. Network Mask Displays the length in bytes of the LSA. Attached Router Identifies the IP address of routers attached to the network. Dell#show ip ospf 1 data network OSPF Router with ID (20.20.20.
PAGE 1079
adv-router ipaddress Command Modes Command History • EXEC • EXEC Privilege • the network’s IP address for Type 3 LSAs or Type 5 LSAs • the router’s OSPF router ID for Type 1 LSAs or Type 4 LSAs • the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. This guide is platform-specific.
PAGE 1080
• adv-router ipaddress Command Modes Command History • EXEC • EXEC Privilege the default destination (0.0.0.0) for Type 5 LSAs (OPTIONAL) Enter the keywords adv-router and the ip-address to display only the LSA information about that router. This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1081
Example Item Description Checksum Displays the Fletcher checksum of the LSA’s complete contents. Length Displays the length in bytes of the LSA. Opaque Type Displays the Opaque type field (the first 8 bits of the Link State ID). Opaque ID Displays the Opaque type-specific ID (the remaining 24 bits of the Link State ID). Dell>show ip ospf 1 database opaque-area OSPF Router with ID (3.3.3.
PAGE 1082
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1083
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1084
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information 1084 Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.20 Introduced on the S6000. 8.3.19.
PAGE 1085
Example Item Description (Link ID) Identifies the link type and address. (Link Data) Identifies the router interface address. Number of TOS Metric Lists the number of TOS metrics. TOS 0 Metric Lists the number of TOS 0 metrics. Dell#show ip ospf 100 database router OSPF Router with ID (1.1.1.10) (Process ID 100) Router (Area 0) LS age: 967 Options: (No TOS-capability, No DC, E) LS type: Router Link State ID: 1.1.1.10 Advertising Router: 1.1.1.
PAGE 1086
show ip ospf database summary Display the network summary (type 3) LSA routing information. Syntax show ip ospf [process-id] database summary [link-state-id] [adv-router ipaddress] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. link-state-id (OPTIONAL) Specify LSA ID in dotted decimal format.
PAGE 1087
Example Item Description LS Age Displays the LSA age. Options Displays the optional capabilities available on router. The following options can be found in this item: • TOS-capability or No TOS-capability is displayed depending on whether the router can support Type of Service. • DC or No DC is displayed depending on whether the originating router can support OSPF over demand circuits. • E or No E is displayed on whether the originating router can accept AS External LSAs.
PAGE 1088
LS Seq Number: 0x80000016 Checksum: 0x1241 Length: 28 Network Mask: /26 TOS: 0 Metric: 1 Dell# Related Commands show ip ospf database — displays OSPF database information. show ip ospf interface Display the OSPF interfaces configured. If OSPF is not enabled on the switch, no output is generated. Syntax show ip ospf [process-id | vrf vrf-name] interface [interface] Parameters Command Modes Command History process-id Enter the OSPF Process ID to show a specific process.
PAGE 1089
Usage Information Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. The following describes the show ip ospf process-id interface command shown in the following example. Item Description GigabitEthernet...
PAGE 1090
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:08 Neighbor Count is 3, Adjacent neighbor count is 2 Adjacent with neighbor 192.168.253.5 (Designated Router) Adjacent with neighbor 192.168.253.3 (Backup Designated Router) Loopback 0 is up, line protocol is up Internet Address 192.168.253.2/32, Area 0.0.0.1 Process ID 1, Router ID 192.168.253.2, Network Type LOOPBACK, Cost: 1 Loopback interface is treated as a stub Host.
PAGE 1091
Example Item Description State Displays the OSPF state of the neighbor. Dead Time Displays the expected time until FTOS declares the neighbor dead. Address Displays the IP address of the neighbor. Interface Displays the interface type slot/port information. Area Displays the neighbor’s area (process ID). Dell#show ip ospf 34 neighbor Neighbor ID 20.20.20.7 192.10.10.2 20.20.20.1 Dell# Pri State Dead Time Address 1 FULL/DR 00:00:32 182.10.10.3 1 FULL/DR 00:00:37 192.10.10.
PAGE 1092
Usage Information Version Description 7.5.1.0 Introduced on the C-Series and E-Series. This command is useful in isolating routing problems between the OSPF and the RTM. For example, if a route is missing from the RTM/FIB but is visible from the display output of this command, the problem is with downloading the route to the RTM. This command has the following limitations: • The display output is sorted by prefixes; intra-area ECMP routes are not displayed together.
PAGE 1093
neighbor router-id Defaults Command Modes Command History • For a port channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. (OPTIONAL) Enter the keyword neighbor then the neighbor’s router-id in dotted decimal format (A.B.C.D.). none • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1094
Row Heading Description TxQ-Len The transmission queue length. RxQ-Len The reception queue length. Tx-Mark The highest number mark in the transmission queue. Rx-Mark The highest number mark in the reception queue. Hello-Q The queue, for transmission or reception, for the hello packets. LSR-Q The queue, for transmission or reception, for the link state request packets.
PAGE 1095
Hello-Q LSR-Q Other-Q 0 0 0 0 0 0 0 0 0 2 0 0 Error packets (Only for RX) Intf-Down Wrong-Len Auth-Err Version No-Buffer Q-OverFlow 0 0 0 0 0 0 Non-Dr Invld-Nbr MD5-Err AreaMis Seq-No Unkown-Pkt 0 0 0 0 0 0 Self-Org 0 Nbr-State 0 Chksum 0 Conf-Issues 0 Socket 0 Error packets (Only for TX) Socket Errors Dell# Usage Information Example (Statistics) 0 The show ip ospf process-id statistics command displays the error packet count received on each interface as: • The hello-timer remaining value for
PAGE 1096
Parameters Defaults process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.
PAGE 1097
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.
PAGE 1098
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1099
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1100
Defaults hold-interval Set the next interval to send the same LSA. This interval is the time between sending the same LSA after the start-interval has been attempted. The range is from 1 to 600,000 milliseconds. max-interval Set the maximum amount of time the system waits before sending the LSA. The range is from 1 to 600,000 milliseconds. • start-interval: 0 msec • hold-interval: 5000 msec • max-interval: 5000 msec Command Modes ROUTER OSPF Command History This guide is platform-specific.
PAGE 1101
Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1102
key-encryptiontype (OPTIONAL) Specifies if the key is encrypted. The values are 0 (key is not encrypted) or 7 (key is encrypted). key Text string used in authentication. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes ROUTER OSPFv3 Command History This guide is platform-specific.
PAGE 1103
area encryption Configure an IPsec encryption policy for OSPFv3 packets in an OSPFv3 area. Syntax Parameters area area-id encryption ipsec spi number esp encryption-algorithm [keyencryption-type] key authentication-algorithm [key-encryption-type] key area area-id Area for which OSPFv3 traffic is to be encrypted. For area-id, enter a number. The range is from 0 to 4294967295. ipsec spi number Security Policy index (SPI) value that identifies an IPsec security policy. The range is from 256 to 4294967295.
PAGE 1104
null Causes an encryption policy configured for the area to not be inherited on the interface. Defaults Not configured. Command Modes ROUTER OSPFv3 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1105
To return to the default bandwidth or to assign cost based on the interface type, use the no auto-cost [reference-bandwidth ref-bw] command. Parameters ref-bw (OPTIONAL) Specify a reference bandwidth in megabits per second. The range is from 1 to 4294967. The default is 100 megabits per second. Defaults 100 megabits per second. Command Modes ROUTER OSPFv3 Command History This guide is platform-specific.
PAGE 1106
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1107
Example Lines Beginning With or Including Description OSPFv3... Debugging is on for all OSPFv3 packets and all interfaces. 05:21:01 Displays the time stamp. Sending Ver:3 Sending OSPF3 version..
PAGE 1108
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.
PAGE 1109
Lines Beginning With or Including Description Area ID: Displays the Area ID. Chksum: Displays the OSPF3 checksum. default-information originate Configure the Dell Networking OS to generate a default external route into an OSPFv3 routing domain. Syntax default-information originate [always] [metric metric-value] [metric-type type-value] [route-map map-name] To return to the default values, use the no default-information originate command.
PAGE 1110
graceful-restart grace-period Enable OSPFv3 graceful restart globally by setting the grace period (in seconds) that an OSPFv3 router’s neighbors continues to advertise the router as adjacent during a graceful restart. Syntax graceful-restart grace-period seconds To disable OSPFv3 graceful restart, enter no graceful-restart grace-period. Parameters seconds Time duration, in seconds, that specifies the duration of the restart process before OSPFv3 terminates the process.
PAGE 1111
To disable graceful restart mode, enter no graceful-restart mode. Parameters planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplanned-only (OPTIONAL) Enter the keywords unplanned-only to indicate graceful restart is supported in an unplanned restart condition only. Defaults OSPFv3 graceful restart supports both planned and unplanned failures.
PAGE 1112
Defaults none Command Modes INTERFACE Command History Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.4.1.0 Introduced on the E-Series and C-Series. ipv6 ospf authentication Configure an IPsec authentication policy for OSPFv3 packets on an IPv6 interface.
PAGE 1113
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on S4810 and Z9000. 8.4.2.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Before you enable IPsec authentication on an OSPFv3 interface, first enable IPv6 unicast routing globally, configure an IPv6 address and enable OSPFv3 on the interface, and assign the interface to an area.
PAGE 1114
• Active — The active system initiates the BFD session. Both systems can be active for the same session. • Passive — The passive system does not initiate a session. It only responds to a request for session initialization from the active system. The default is Active. Defaults See Parameters Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1115
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T.
PAGE 1116
Version Description 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Usage Information By default, the dead interval is four times longer than the default hello-interval. Related Commands ipv6 ospf hello-interval – specifies the time interval between hello packets. ipv6 ospf encryption Configure an IPsec encryption policy for OSPFv3 packets on an IPv6 interface.
PAGE 1117
For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1118
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.2 Introduced on E-Series TeraScale. 8.3.19.
PAGE 1119
Version Description 9.1.(0.0) Introduced on the S4810 and Z9000. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. 8.3.19.0 Introduced on the S4820T. Usage Information The time interval between hello packets must be the same for routers in a network. Related Commands ipv6 ospf dead-interval – specifies the time interval between hello packets was received from a router.
PAGE 1120
ipv6 router ospf Enable OSPF for IPv6 router configuration. Syntax ipv6 router ospf process-id [vrf vrf-name] To exit OSPF for IPv6, use the no ipv6 router ospf process-id command. Parameters process-id Enter the process identification number. The range is from 1 to 65535. vrf vrf-name (Optional) Enter the keyword vrf followed by the name of the VRF to install IPv6 routes in that VRF. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1121
Command History Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Added support for Multi-Process OSPF. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.1 Introduced on the E-Series. passive-interface Disable (suppress) sending routing updates on an interface.
PAGE 1122
Usage Information Version Description 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. By default, no interfaces are passive. Routing updates are sent to all interfaces on which the routing protocol is enabled. If you disable the sending of routing updates on an interface, the particular address prefix continues to be advertised to other interfaces, and updates from other routers on that interface continue to be received and processed.
PAGE 1123
route-map mapname (OPTIONAL) Enter the keywords route-map then the name of an established route map. If the route map is not configured, the default is deny (to drop all routes). tag tag-value (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPFv3. The range is from 0 to 4294967295 The default is 0. Defaults Not configured. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific.
PAGE 1124
Defaults The router ID is selected automatically from the set of IPv4 addresses configured on a router. Command Modes ROUTER OSPF for OSPFv2 ROUTER OSPFv3 for OSPFv3 Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1125
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series TeraScale. 8.3.19.0 Introduced on the S4820T. The show crypto ipsec policy command output displays the AH and ESP parameters configured in IPsec security policies, including the SPI number, keys, and algorithms used.
PAGE 1126
Field Description Inbound ESP SPI and Outbound ESP SPI The encapsulating security payload (ESP) security policy index (SPI) for inbound and outbound links. Inbound ESP Auth Key and Outbound Auth Key The ESP authentication key for inbound and outbound links. Inbound ESP Cipher Key and Outbound ESP Cipher Key The ESP encryption key for inbound and outbound links. Transform set The set of security protocols and algorithms used in the policy.
PAGE 1127
Version Description 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced on the S4810 and Z9000. 8.4.2.0 Introduced on the E-Series TeraScale. 8.3.19.0 Introduced on the S4820T. Usage Information The show crypto ipsec sa ipv6 command output displays security associations set up for OSPFv3 links in IPsec authentication and encryption policies on the router. Related Commands show crypto ipsec policy – displays the configuration of IPsec authentication and encryption policies.
PAGE 1128
show crypto ipsec sa ipv6 Command Fields Field Description Interface IPv6 interface Link local address IPv6 address of interface IPSecv6 policy name Name of the IPsec security policy applied to the interface. inbound/outbound ah Authentication policy applied to inbound or outbound traffic. inbound/outbound esp Encryption policy applied to inbound or outbound traffic. spi Security policy index number used to identify the policy.
PAGE 1129
Command History Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Added support for OSPFv3 on the S4810 and Z9000. 8.4.2.2 Added support for the display of graceful restart parameters and Type-11 Grace LSAs on E-Series TeraScale routers. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for C-Series.
PAGE 1130
Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 Area 1 database summary Type Count/Status Brd Rtr Count 1 AS Bdr Rtr Count 1 LSA count 8 Rtr LSA Count 1 Net LSA Count 0 Inter Area Pfx LSA Count 5 Inter Area Rtr LSA Count 0 Group Mem LSA Count 0 Type-7 LSA count 0 Intra Area Pfx LSA Count 2 Intra Area TE LSA Count 2 E1200-T2C2#sh ipv6 ospf neighbor Neighbor ID Interface 63.114.8.
PAGE 1131
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. If you enable BFD at the global level, show ipv6 ospf interface shows the BFD provisioning. If you enable BFD at the interface level, show ipv6 ospf interface shows the BFD interval timers.
PAGE 1132
Command History Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.1.(0.0) Introduced support for OSPFv3 on the S4810 and Z9000. 8.3.19.0 Introduced on the S4820T. 7.8.1.0 Added support for the C-Series. 7.4.1.0 Introduced on the E-Series. Dell#show ipv6 ospf 3 neighbor gi 1/2 Neighbor ID 63.114.8.
PAGE 1133
Example Dell#conf Dell(conf)#ipv6 router ospf 1 Dell(conf-ipv6-router_ospf)#timer spf 2 5 Dell(conf-ipv6-router_ospf)# Dell(conf-ipv6-router_ospf)#show config ! ipv6 router ospf 1 timers spf 2 5 Dell(conf-ipv6-router_ospf)# Dell(conf-ipv6-router_ospf)#end Dell# Open Shortest Path First (OSPFv2 and OSPFv3) 1133
PAGE 1134
38 Policy-based Routing (PBR) Policy-based routing (PBR) allows you to apply routing policies to specific interfaces. To enable PBR, create a redirect list and apply it to the interface. After the redirect list is applied to the interface, all traffic passing through the interface is subject to the rules defined in the redirect list. PBR is supported by the Dell Networking Operating System (OS).
PAGE 1135
ip redirect-group Apply a redirect list (policy-based routing) on an interface. You can apply multiple redirect lists to an interface by entering this command multiple times. Syntax ip redirect-group redirect-list-name To remove a redirect list from an interface, use the no ip redirect-group name command. Parameters redirect-list-name Enter the name of a configured redirect list. Defaults none Command Modes INTERFACE (conf-if-vl-) Command History Usage Information Version Description 9.8(0.
PAGE 1136
To remove a redirect list, use the no ip redirect-list command. Parameters redirect-list-name Defaults None Command Modes CONFIGURATION Command History Enter the name of a redirect list. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 8.4.2.1 Introduced on the C-Series and S-Series. 8.4.2.
PAGE 1137
any Enter the keyword any to specify that all traffic is subject to the filter. host ip-address Enter the keyword host then he IP address to specify a host IP address. destination Enter the IP address of the network or host to which the packets are sent.
PAGE 1138
redirect Configure a rule for the redirect list. Syntax redirect {ip-address | slot/port} | tunnel tunnel-id}[track ] {ipprotocol-number | protocol-type [bit]} {source mask | any | host ipaddress} {destination mask | any | host ip-address} [operator] To remove this filter, use one of the following: Parameters • Use the no seq sequence-number command if you know the filter’s sequence number.
PAGE 1139
destination Enter the IP address of the network or host to which the packets are sent. operator (OPTIONAL) For TCP and UDP parameters only. Enter one of the following logical operand: Defaults none Command Modes REDIRECT-LIST Command History • eq = equal to • neq = not equal to • gt = greater than • lt = less than • range = inclusive range of ports (you must specify two ports for theport command parameter.) Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1140
ip-address Enter the keyword IP address of the forwarding router. tunnel Enter the keyword tunnel to configure the tunnel setting. tunnel-id Enter the keyword tunnel-id to redirect the traffic. track Enter the keyword track to enable the tracking. track Enter the keyword track to track object-id. ip-protocol-number Enter the keyword ip-protocol-number then the number from 0 to 255 for the protocol identified in the IP protocol header.
PAGE 1141
destination-portrange Defaults none Command Modes REDIRECT-LIST Command History Enter the keywords destination-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Added support for the track-id on the S4810, S4820T, S6000, S6000-ON, and Z9000. 9.5(0.1) Introduced on the Z9500. 9.4(0.
PAGE 1142
Cam Port VlanID Proto Tcp Src Dst SrcIp DstIp Next-hop Egress Index Flag Port Port MAC Port -------------------------------------------------------------00000 5 N/A IP 0x0 0 0 22.22.2.22/32 33.33.3.0/24 00:01:e8:8a:fd:76 0/0 00001 5 N/A 145 0x0 0 0 0.0.0.0/0 44.4.4.4/32 00:01:e8:8a:fd:76 Vl 100(0/1) 00002 5 N/A TCP 0x0 0 0 55.1.3.0/24 66.6.6.6/32 00:01:e8:8a:fd:76 Po 128 00003 5 N/A UDP 0x0 0 0 55.1.3.0/24 66.6.6.6/32 00:01:e8:8a:fd:76 Po 128 00004 5 N/A IP 0x0 0 0 0.0.0.0/0 0.0.0.
PAGE 1143
seq 40 redirect 43.1.1.2 tcp 155.55.2.0/24 222.22.2.0/24, Next-hop reachable (via Vl 30) seq 45 redirect 31.1.1.2 track 200 ip 12.0.0.0 255.0.0.197 13.0.0.0 255.0.0.
PAGE 1144
39 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell Networking operating software on the platform. The following describes the IPv4 PIM-SIM commands. IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim rp-mapping The bootstrap router (BSR) feature uses this command to remove all or particular rendezvous point (RP) advertisement.
PAGE 1145
Usage Information Version Description 7.8.1.0 Introduced on the S-Series. This command re-applies the RP mapping logic for all the groups learnt by the node. Any stale information corresponding to the existing mapping configuration is updated. As a result, the existing BSR cache and the *,G's are deleted only if these entries are stale. clear ip pim tib Clear PIM tree information from the PIM database.
PAGE 1146
debug ip pim View IP PIM debugging messages. Syntax debug ip pim [vrf vrf-name] [bsr | events | group | packet [in | out] | register | state | timer [assert | hello | joinprune | register]] To disable PIM debugging, use the no debug ip pim [vrf vrf-name] command or use the undebug allto disable all debugging command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to view IP PIM debugging messages corresponding to that VRF.
PAGE 1147
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. ip pim bsr-border Define the border of PIM domain by filtering inbound and outbound PIM-BSR messages per interface.
PAGE 1148
ip pim bsr-candidate To join the Bootstrap election process, configure the PIM router. Syntax ip pim [vrf vrf-name] bsr-candidate interface [hash-mask-length] [priority] To return to the default value, use the no ip pim bsr-candidate [vrf vrf-name] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF to configure the PIM router on a VRF.
PAGE 1149
ip pim dr-priority Change the designated router (DR) priority for the interface. Syntax ip pim dr-priority priority-value To remove the DR priority value assigned, use the no ip pim dr-priority command. Parameters priority-value Enter a number. Preference is given to larger/higher number. The range is from 0 to 4294967294. The default is 1. Defaults 1 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1150
ext-access-list Enter the name of an extended access list. in Enter the keyword in to apply the ACL filter to in-bound traffic. out Enterthe keyword out to apply the ACL filter to out-bound traffic. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1151
The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.0 Introduced Dell(conf)# ip access-list standard map1 Dell(config-std-nacl)# permit 224.0.0.
PAGE 1152
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the C-Series and S-Series. 7.6.1.0 Introduced on the E-Series. Do not enter this command before creating the access-list. ip pim query-interval Change the frequency of PIM Router-Query messages.
PAGE 1153
ip pim register-filter To prevent a PIM source DR from sending register packets to an RP for the specified multicast source and group, use this feature. Syntax ip pim [vrf vrf-name] register-filter access-list To return to the default, use the no ip pim [vrf vrf-name] register-filter access-list command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF.
PAGE 1154
To remove an RP address, use the no ip pim [vrf vrf-name] rp-address address {groupaddress group-address mask} [override] command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. address Enter the RP address in dotted decimal format (A.B.C.D).
PAGE 1155
To return to the default value, use the no ip pim [vrf vrf-name] rp-candidate {interface [priority]} command. Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf followed by the name of the VRF. NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. interface priority Enter the following keywords and slot/port or number information: • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
PAGE 1156
Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.
PAGE 1157
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1158
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. Added support for VRF on S6000, S4810, S4820T, Z9000, Z9500, and S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.1 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series.
PAGE 1159
NOTE: Applies to specific VRF if input is provided, else applies to Default VRF. infinity (OPTIONAL) Enter the keyword infinity to never switch to the source-tree. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1160
Usage Information Version Description 8.4.1.0 Introduced on the E-Series ExaScale. By default, when you enable PIM-SM snooping, a switch floods all multicast traffic to the PIM designated router (DR), including unnecessary multicast packets. To minimize the traffic sent over the network to the designated router, you can disable designated-router flooding.
PAGE 1161
Next bootstrap message in 00:00:08 This system is a candidate BSR Candidate BSR address: 7.7.7.7, priority: 0, hash mask length: 30 show ip pim interface View information on the interfaces with IP PIM enabled. S3048–ON Syntax Command Modes Command History show ip pim [vrf vrf-name] interface • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1162
Field Description DR Displays the IP address of the Designated Router for that interface. The show ip pim interface command does not display information corresponding to the loop-back interfaces. Example Dell#show ip pim interface Address Interface Ver/ Mode 165.87.34.5 Gi 1/10 v2/S 10.1.1.2 Vl 10 v2/S 20.1.1.5 Vl 20 v2/S 165.87.31.200 Vl 30 v2/S Nbr Count 0 1 1 1 Query Intvl 30 30 30 30 DR Prio 1 1 1 1 DR 165.87.34.5 10.1.1.2 20.1.1.5 165.87.31.201 show ip pim neighbor View PIM neighbors.
PAGE 1163
Field Description Uptime/expires Displays the amount of time the neighbor has been up then the amount of time until the neighbor is removed from the multicast routing table (that is, until the neighbor hold time expires). Ver Displays the PIM version number. • DR prio/Mode Example v2 = PIM version 2 Displays the Designated Router priority and the mode.
PAGE 1164
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. Example Dell#show ip pim rp Group RP 224.2.197.115 165.87.20.4 224.2.217.146 165.87.20.4 224.3.3.3 165.87.20.4 225.1.2.1 165.87.20.4 225.1.2.2 165.87.20.4 229.1.2.1 165.87.20.4 229.1.2.2 165.87.20.4 Dell# Example (Mapping) Dell#show ip pim rp mapping PIM Group-to-RP Mappings Group(s): 224.0.
PAGE 1165
Usage Information Example (#2) Version Description 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series ExaScale. The following describes the show ip pim snooping interface commands shown in the following example. Field Description Interface Displays the VLAN interfaces with PIM-SM snooping enabled.
PAGE 1166
Usage Information Version Description 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.1.1 Introduced on the E-Series ExaScale. The following describes the show ip pim snooping neighbor commands shown in the following example. Field Description Neighbor address Displays the IP address of the neighbor learned through PIM-SM snooping.
PAGE 1167
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.5(0.1) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.12.
PAGE 1168
Example Dell#show ip pim snooping tib PIM Multicast Snooping Table Flags: J/P - (*,G) Join/Prune, j/p - (S,G) Join/Prune SGR-P - (S,G,R) Prune Timers: Uptime/Expires * : Inherited port (*, 225.1.2.1), uptime 00:00:01, expires 00:02:59, RP 165.87.70.1, flags: J Incoming interface: Vlan 2, RPF neighbor 0.0.0.0 Outgoing interface list: GigabitEthernet 2/11 RPF 165.87.32.2 00:00:01/00:02:59 GigabitEthernet 2/13 Upstream Port -/Dell#show ip pim snooping tib vlan 2 225.1.2.1 165.87.1.
PAGE 1169
Exmaple Version Description 7.7.1.0 Introduced on the C-Series. 7.5.1.0 Introduced on the E-Series. Group Address / MaskLen show ip pim summary View information about PIM-SM operation. S3048–ON Syntax Command Modes Command History show ip pim [vrf vrf-name] summary • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1170
0/0 (S,G,Rpt) entries in PIM-TIB/MFC 0 0 0 0 PIM nexthops RPs sources Register states Message summary: 2582/2583 Joins sent/received 5/0 Prunes sent/received 0/0 Candidate-RP advertisements sent/received 0/0 BSR messages sent/received 0/0 State-Refresh messages sent/received 0/0 MSDP updates sent/received 0/0 Null Register messages sent/received 0/0 Register-stop messages sent/received Data path event summary: 0 no-cache messages received 0 last-hop switchover messages received 0/0 pim-assert messages sen
PAGE 1171
Usage Information Example Version Description 8.3.12.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. 8.1.1.0 Introduced on the E-Series ExaScale. 7.8.1.0 Introduced on the S-Series. The following describes the show ip pim tib command shown in the following example. Field Description (S, G) Displays the entry in the multicast PIM database. uptime Displays the amount of time the entry has been in the PIM route table.
PAGE 1172
(20.10.4.9, 225.1.1.1), uptime 00:06:21, expires 00:02:06, flags: CT Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (*, 225.1.1.2), uptime 00:40:15, expires 00:00:00, RP 20.40.4.4, flags: SCJ Incoming interface: Vlan 2007, RPF neighbor 20.30.124.4 Outgoing interface list: Vlan 2006 Forward/Sparse 00:06:21/Never (20.10.4.9, 225.1.1.2), uptime 00:06:21, expires 00:02:06, flags: CT Incoming interface: Vlan 2007, RPF neighbor 20.30.124.
PAGE 1173
40 Port Monitoring The port monitoring feature allows you to monitor network traffic by forwarding a copy of each incoming or outgoing packet from one port to another port. Important Points to Remember • Port monitoring is supported on physical ports and logical interfaces, such as port channels and virtual local area networks (VLANs). • The monitoring (destination, “MG”) and monitored (source, “MD”) ports must be on the same switch.
PAGE 1174
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-7.7.1.0 Introduced on the E-Series.
PAGE 1175
Related Commands Version Description 9.8(0.0) Introduced on the S6000, Z9500, S6000-ON. show running-config monitor session — displays information about monitor configurations. monitor session Create a session for monitoring traffic with port monitoring. Syntax monitor session session-ID [type { rpm | erpm [set ip dscp dscp_value | set ip ttl ttl_value]}] [drop] To delete a session, use the no monitor session session-ID command. To delete all monitor sessions, use the no monitor session all command.
PAGE 1176
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the drop parameter. 9.7(0.0) Introduced on the S6000-ON. Introduced the set ip dscp and set ip ttl parameters. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. 9.0.2.0 Introduced on the S6000. 9.0.2.0 Introduced on the MXL. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810.
PAGE 1177
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000-ON, Z9500. monitor session — enables a monitoring session. show monitor session — displays the monitor session. show config Display the current monitor session configuration. Syntax show config Defaults none Command Modes MONITOR SESSION (conf-mon-sess-session-ID) Command History This guide is platform-specific.
PAGE 1178
show monitor session Display information about monitoring sessions. Syntax show monitor session {session-ID} To display monitoring information for all sessions, use the show monitor session command. Parameters Defaults session-ID (OPTIONAL) Enter a session identification number. The range is from 0 to 65535. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1179
show running-config monitor session Display the running configuration of all monitor sessions or a specific session. Syntax show running-config monitor session {session-ID} To display the running configuration for all monitor sessions, use the show running-config monitor session command. Parameters Defaults Command Modes Command History session-ID (OPTIONAL) Enter a session identification number. The range from 0 to 65535. none • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1180
source (port monitoring) Configure a port monitor source. Syntax source {interface | range | any} destination interface direction {rx | tx | both} To disable a monitor source, use the no source interface destination interface direction {rx | tx | both} command. Parameters source interface Enter one of the following keywords and slot/port information: • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1181
The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the any parameter. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4.0.0 Added support for Source and destination. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.
PAGE 1182
41 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell Networking operating software is supported on the platforms. Private VLANs extend the Dell Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a traditional VLAN into subdomains identified by a primary and secondary VLAN pair. The Dell Networking OS private VLAN implementation is based on RFC 3069. For more information, refer to the following commands.
PAGE 1183
– A trunk port in a PVLAN is always tagged. – A trunk port in Tagged mode carries primary or secondary VLAN traffic. The tag on the packet helps identify the VLAN to which the packet belongs. – A trunk port can also belong to a regular VLAN (non-private VLAN). ip local-proxy-arp Enable/disable Layer 3 communication between secondary VLANs in a private VLAN.
PAGE 1184
show arp — displays the ARP table. switchport mode private-vlan — sets PVLAN mode of the selected port. private-vlan mode Set PVLAN mode of the selected VLAN to community, isolated, or primary. S3048 Syntax [no] private-vlan mode {community | isolated | primary} To remove the PVLAN configuration, use the no private-vlan mode {community | isolated | primary} command syntax. Parameters community Enter the keyword community to set the VLAN as a community VLAN.
PAGE 1185
Only ports (and port channels) configured as promiscuous, host, or PVLAN trunk ports (as previously described) can be added to the PVLAN. No other regular ports can be added to the PVLAN. After using this command to configure a VLAN as a primary VLAN, use the private-vlan mapping secondary-vlan command to map secondary VLANs to this VLAN. Related Commands private-vlan mapping secondary-vlan — maps secondary VLANs to the selected primary VLAN.
PAGE 1186
Related Commands • Specified in comma-delimited or hyphenated-range format. • Specified with this command even before they have been created. • Amended by specifying the new secondary VLAN to be added to the list. private-vlan mode — sets the mode of the selected VLAN to community, isolated, or primary. switchport mode private-vlan — sets PVLAN mode of the selected port. switchport mode private-vlan Set PVLAN mode of the selected port.
PAGE 1187
Usage Information The assignment of the various PVLAN port types to port and port channel (LAG) interfaces is shown in the following example.
PAGE 1188
42 Per-VLAN Spanning Tree Plus (PVST+) The Dell Networking operating software implementation of per-VLAN spanning tree plus (PVST+) is based on the IEEE 802.1w standard spanning tree protocol. Dell Networking OS supports PVST+ on the S3048 platform. NOTE: For easier command line entry, the plus (+) sign is not used at the command line. description Enter a description of the PVST+. S3048 Syntax description {description} To remove the description, use the no description {description} command.
PAGE 1189
Related Commands protocol spanning-tree pvst — enter SPANNING TREE mode on the switch. disable Disable PVST+ globally. S3048 Syntax disable To enable PVST+, use the no disable command. Defaults Disabled. Command Modes CONFIGURATION (conf-pvst) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1190
extend system-id To augment the Bridge ID with a VLAN ID so that PVST+ differentiate between BPDUs for each VLAN, use extend system ID. If the VLAN receives a BPDU meant for another VLAN, PVST+ does not detect a loop, and both ports can remain in Forwarding state. S3048 Syntax extend system-id Defaults Disabled Command Modes PROTOCOL PVST Command History This guide is platform-specific.
PAGE 1191
protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. S3048 Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 1192
show spanning-tree pvst View the Per-VLAN spanning tree configuration. S3048 Syntax show spanning-tree pvst [vlan vlan-id] [brief] [guard] Parameters vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094. brief (OPTIONAL) Enter the keyword brief to view a synopsis of the PVST+ configuration information.
PAGE 1193
Usage Information Example (Brief) Version Description 7.5.1.0 Introduced on the C-Series. 6.4.1.0 Expanded to display port error disable state (EDS) caused by loopback BPDU inconsistency and Port VLAN ID inconsistency. 6.2.1.1 Introduced. The following describes the show spanning-tree pvst command shown in the following examples. Field Description Interface Name PVST interface. Instance PVST instance.
PAGE 1194
Port path cost 20000, Port priority 128, Port Identifier 128.131 Designated root has priority 4096, address 0001.e805.e3:06 Designated bridge has priority 4096, address 0001.e805.e3:06 Designated port id is 128.131, designated path cost 0 Number of transitions to forwarding state 1 BPDU sent 1567, received 0 The port is not in the Edge port mode Port 146 (GigabitEthernet 1/16) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.
PAGE 1195
Te 1/2/1 5 Te 1/3/1 5 Related Commands FWD EDS(Shut) Loopguard Bpduguard spanning-tree pvst — configure PVST+ on an interface. spanning-tree pvst Configure a PVST+ interface with one of these settings: edge port with optional bridge port data unit (BPDU) guard, port disablement if an error condition occurs, port priority or cost for a VLAN range, loop guard, or root guard.
PAGE 1196
rootguard (C-, S-, and E-Series TeraScale only) Enter the keyword rootguard to enable root guard on a PVST+ port or port-channel interface. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 1197
When used in a PVST+ network, loop guard is performed per-port or per-port channel at a VLAN level. If no BPDUs are received on a VLAN interface, the port or port-channel transitions to a Loop-Inconsistent (blocking) state only for this VLAN. Enabling Portfast BPDU guard and loop guard at the same time on a port results in a port that remains in a Blocking state and prevents traffic from flowing through it.
PAGE 1198
Usage Information Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced. Some non-Dell Networking systems which have hybrid ports participating in PVST+ transmit two kinds of BPDUs: an 802.1D BPDU and an untagged PVST+ BPDU. Dell Networking systems do not expect PVST+ BPDU on an untagged port. If this happens, Dell Networking OS places the port in the Error-Disable state.
PAGE 1199
Usage Information Version Description 6.5.1.0 Introduced. By default, Dell Networking OS implements an optimized flush mechanism for PVST+. This implementation helps in flushing the MAC addresses only when necessary (and less often) allowing for faster convergence during topology changes. However, if a standards-based flush mechanism is needed, you can turn this knob command on to enable flushing MAC addresses after receiving every topology change notification.
PAGE 1200
Related Commands vlan forward-delay — changes the time interval before Dell Networking OS transitions to the Forwarding state. vlan hello-time — change the time interval between BPDUs. vlan max-age — changes the time interval before PVST+ refreshes. show spanning-tree pvst — displays the PVST+ configuration. vlan forward-delay Set the amount of time the interface waits in the Listening state and the Learning state before transitioning to the Forwarding state.
PAGE 1201
Related Commands vlan bridge-priority — sets the bridge-priority value. vlan hello-time — changes the time interval between BPDUs. vlan max-age — changes the time interval before PVST+ refreshes. show spanning-tree pvst — displays the PVST+ configuration. vlan hello-time Set the time interval between generation of PVST+ 7 BPDUs. S3048 Syntax vlan vlan-range hello-time seconds To return to the default value, use the no vlan hello-time command.
PAGE 1202
Related Commands vlan bridge-priority — sets the bridge-priority value. vlan forward-delay — changes the time interval before Dell Networking OS transitions to the forwarding state. vlan max-age — changes the time interval before PVST+ refreshes. show spanning-tree pvst — displays the PVST+ configuration. vlan max-age To maintain configuration information before refreshing that information, set the time interval for the PVST+ bridge.
PAGE 1203
Related Commands vlan bridge-priority — sets the bridge-priority value. vlan forward-delay — changes the time interval before Dell Networking OS transitions to the forwarding state. vlan hello-time — changes the time interval between BPDUs. show spanning-tree pvst — displays the PVST+ configuration.
PAGE 1204
43 Quality of Service (QoS) The Dell Networking operating software commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell Networking Products. platform. Global Configuration Commands There is only one global configuration QoS command. qos-rate-adjust By default, while rate limiting, policing, and shaping, Dell Networking OS does not include the Preamble, SFD, or the IFG fields.
PAGE 1205
Usage Information By default, when rate policing and shaping, the system does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations. Per-Port QoS Commands Per-port QoS (port-based QoS) allows you to define the QoS configuration on a per-physical-port basis. dot1p-priority Assign a value to the IEEE 802.1p bits on the traffic this interface receives.
PAGE 1206
rate police Police the incoming traffic rate on the selected interface. S3048–ON Syntax rate police [kbps] committed-rate [burst-KB] [peak [kbps] peak-rate [burstKB]] [vlan vlan-id] Parameters kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps). committed-rate Enter the bandwidth in Mbps. The range is from 0 to 40000. burst-KB (OPTIONAL) Enter the burst size in KB.
PAGE 1207
S-Series On one interface, you can configure the rate police command for a VLAN or you can configure the rate police command for an interface. rate shape Shape the traffic output on the selected interface. S3048–ON Syntax Parameters rate shape [kbps] rate [burst-KB] kbps Enter the keyword kbps to specify the rate limit in Kilobits per second (Kbps). On S-Series, make the value a multiple of 64. The range is from 0 to 40000000. The default granularity is Megabits per second (Mbps).
PAGE 1208
NOTE: When packets of size greater than 7000 bytes are expected to be received from the network, Dell Networking recommends that you configure the burst value to be more than 175 KB if you configured the rate shape. Such a setting ensures proper bandwidth sharing across queues. Related Commands rate-shape — shapes traffic output as part of the designated policy. service-class dot1p-mapping Configure a service-class criterion based on a dot1p value.
PAGE 1209
To return to the default setting, use the no service-class dynamic dot1p command. Defaults Command Modes Command History All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command. The default mapping is as follows: dot1p Queue ID 0 0 1 0 2 0 3 1 4 2 5 3 6 3 7 3 • INTERFACE • CONFIGURATION This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1210
You can apply this command on both physical interfaces and port channels. When you set the service-class dynamic for a port channel, the physical interfaces assigned to the port channel are automatically configured; you cannot assign the service-class dynamic command to individual interfaces in a port channel. • All dot1p traffic is mapped to Queue 0 unless you enable the service-class dynamic dot1p command on an interface or globally.
PAGE 1211
Policy-Based QoS Commands Policy-based traffic classification is handled with class maps. These maps classify unicast traffic into one of eight classes in S-Series or eight classes in case of S6000. Dell Networking OS enables you to match multiple class maps and specify multiple match criteria. Policy-based QoS is not supported on logical interfaces, such as port-channels, VLANS, or loopbacks. bandwidth-percentage Assign a percentage of weight to the class/queue.
PAGE 1212
Parameters match-all Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-all to determine that the packets must meet all the match criteria in order to be a member of the class. match-any Determines how packets are evaluated when multiple match criteria exist. Enter the keywords match-any to determine that the packets must meet at least one of the match criteria in order to be a member of the class.
PAGE 1213
match ip access-group — configures the match criteria based on the access control list (ACL). match ip precedence — identifies the IP precedence values as match criteria. match ip dscp — configures the match criteria based on the DSCP value. match mac access-group — configures a match criterion for a class map based on the contents of the designated MAC ACL. match mac dot1p — configures a match criterion for a class map based on a dot1p value.
PAGE 1214
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. show qos statistics — displays the QoS statistics. description Add a description to the selected policy map or QoS policy. S3048–ON Syntax description {description} To remove the description, use the no description {description} command.
PAGE 1215
qos-policy-output — creates an output QoS-policy on the router. wred-profile — creates a WRED profile. match ip access-group Configure match criteria for a class map, based on the access control list (ACL). NOTE: IPv6 class-maps and IP-any class-maps do not match. This condition is true for IPv6 and IP-any class-maps on both ACLs as well as VLANs.
PAGE 1216
Version Description 7.5.1.0 Introduced on the C-Series. Added support for the DSCP Marking option. 6.1.1.1 Introduced on the E-Series. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. For class-map match-any, a maximum of five ACL match criteria are allowed. For class-map match-all, only one ACL match criteria is allowed. Related Commands class-map — identifies the class map.
PAGE 1217
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Added the keyword multicast . Added the DSCP Marking option support on the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. Added support for the DSCP Marking option. 6.2.1.1 Introduced on the E-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria.
PAGE 1218
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.
PAGE 1219
Parameters vlan vlan-id Enter the keyword vlan and then the ID of the VLAN. The range is from 1 to 4094. Defaults None. Command Modes CONF-CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1220
Usage Information Version Description 9.4.(0.0) Introduced on the S-Series and Z-Series. To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Use this command to match an IP class-map against a single VRF ID . Related Commands class-map — identifies the class map. match mac access-group Configure a match criterion for a class map, based on the contents of the designated MAC ACL.
PAGE 1221
match mac dot1p Configure a match criterion for a class map based on a dot1p value. S3048–ON Syntax Parameters match mac dot1p {dot1p-list} dot1p-list Enter a dot1p value. The range is from 0 to 7. Defaults none Command Modes CLASS-MAP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1222
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1223
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Usage Information An aggregate output QoS policy applies to all outbound port traffic. An aggregate output QoS policy can coexist with per-queue output QoS policies.
PAGE 1224
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 Expanded to add support for Layer 2. 6.1.1.1 Introduced on the E-Series.
PAGE 1225
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information To assign traffic to different flows using QoS policy, use the Output Policy map. This command enables Policy-Map-Output Configuration mode (conf-policy-map-out).
PAGE 1226
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series. Use this command to specify the name of the input QoS policy.
PAGE 1227
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Policy name character limit increased from 16 to 32. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Usage Information Use this command to specify the name of the output QoS policy.
PAGE 1228
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.0 Introduced on the S4820T. 8.3.8.10 Introduced on the S4810. 7.5.1.0 Added support for multicast-bandwidth. 7.4.1.0 and 6.
PAGE 1229
Pre-defined Profiles: wred_drop, wred-ge_y, wred_ge_g, wred_teng_y, wred_teng_g. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 8.3.19.
PAGE 1230
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1231
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1232
Parameters policy-map-name Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist. layer2 (OPTIONAL) Enter the keyword layer2 to specify a Layer 2 Class Map. The default is Layer 3. Defaults Layer 3 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1233
To remove the output policy map from the interface, use the no service-policy output policymap-name command. Parameters policy-map-name Enter the name for the policy map in character format (32 characters maximum). You can identify an existing policy map or name one that does not yet exist. Defaults none Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1234
NOTE: This option is available under policy-map-input only. qos-policy qospolicy-name (OPTIONAL) Enter the keywords qos-policy then the QoS policy name assigned to the queue in text format (32 characters maximum). This specifies the input QoS policy assigned to the queue under policy-map-input and output QoS policy under policy-map-output context. Defaults none Command Modes CONFIGURATION (conf-policy-map-in and conf-policy-map-out) Command History This guide is platform-specific.
PAGE 1235
mac-dot1p value Enter the keywords mac-dot1p then the dot1p value. The range is from 0 to 7. Defaults none Command Modes CONFIGURATION (conf-qos-policy-in) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1236
The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1237
Version Description 8.3.12.0 Introduced on the S4810. Usage Information trust dot1p, do1p-priority, service-class dynamic dot1; all these features work over the mapping in this command output. Related Commands service-class dot1p-mapping — Identifies the class map. show qos policy-map View the QoS policy map information.
PAGE 1238
Example (IPv4) Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series only: Added trust IPv6 diffserv . 6.2.1.1 Introduced on the E-Series.
PAGE 1239
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.0 E-Series Only: Added Trust IPv6 diffserv. 6.1.1.1 Introduced on the E-Series.
PAGE 1240
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1241
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.1 Introduced on the E-Series.
PAGE 1242
Example Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 6.1.1.1 Introduced on the E-Series. Dell#show qos qos-policy-output Qos-policy-output qosOut Rate-limit 50 50 peak 50 50 Wred yellow 1 Wred green 1 show qos statistics View QoS statistics.
PAGE 1243
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.8(0.0) Added the egress-queue keyword. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1244
show qos wred-profile View the WRED profile details. S3048–ON Syntax show qos wred-profile wred-profile-name Parameters Defaults wred-profile-name Enter the WRED profile name to view the profile details. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1245
stack-unitnumber (OPTIONAL) Enter the keyword stack-unit then the stack-unit slot number. port-set portpipe number Enter the keywords port-set then the stack-unit port pipe number. The range is from 0 or 1. stack-unit all (OPTIONAL) Enter the keywords stack-unit all to indicate all stack-unit. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1246
Field Description Status (Allowed ports) Indicates if the input policy map configuration on an interface belonging to a stackunit/port-pipe is successful — Allowed (n) — or not successful — Exception. The allowed number (n) indicates the number of ports in that port-pipe on which the Policy Map can be applied successfully. NOTE: In a Layer 2 Policy Map, IPv4/IPv6 rules are not allowed; therefore, the output contains only L2ACL CAM partition entries.
PAGE 1247
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.8.0 Introduced on the S4810. 6.1.1.1 Introduced on the E-Series. To configure the minimum and maximum threshold values for user-defined profiles, use this command.
PAGE 1248
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added fallback to the E-Series. 8.2.1.
PAGE 1249
wred Designate the WRED profile to yellow or green traffic. S3048–ON Syntax wred {yellow | green} profile-name To remove the WRED drop precedence, use the no wred {yellow | green} [profile-name] command. Parameters yellow | green Enter the keyword yellow for yellow traffic. A DSCP value of xxx110 and xxx100, xxx101 maps to yellow. Enter the keyword green for green traffic. A DSCP value of xxx0xx are green and DSCP 111111 are red packets.
PAGE 1250
wred ecn To indicate network congestion, rather than dropping packets, use explicit congestion notification (ECN). S3048–ON Syntax wred ecn To stop marking packets, use the no wred ecn command. Defaults none Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1251
wred-profile Create a WRED profile and name the profile. S3048–ON Syntax wred-profile wred-profile-name To remove an existing WRED profile, use the no wred-profile command. Parameters wred-profile-name Enter your WRED profile name in character format (32 character maximum). Or use one of the pre-defined WRED profile names. You can configure up to 26 WRED profiles plus the five pre-defined profiles, for a total of 31 WRED profiles.
PAGE 1252
DSCP Color Map Commands The DSCP color map allows you to set the number of specific DSCP values to yellow or red. Traffic marked as yellow delivers traffic to the egress queue which will either transmit the packet if it has available bandwidth or drop the packet due to no ability to send. Traffic marked as red (high drop precedence) is dropped. dscp Sets the number of specific DSCP values for a color map profile to yellow or red.
PAGE 1253
Example Dell(conf-dscp-color-map)# dscp yellow 9,10,11,13,15,16 Related Commands qos dscp-color-map — configures the DSCP color map qos dscp-color-policy— configures a DSCP color policy qos dscp-color-map Configure the DSCP color map. Syntax qos dscp-color-map map-name To remove a color map, use the no qos dscp-color-map map-name command. Parameters map-name Enter the name of the DSCP color map. The map name can have a maximum of 32 characters.
PAGE 1254
To remove a color policy map profile, use the no dscp-color-policy color-map-profile-name command. Parameters color-map-profilename Enter the color map profile name. The name can have a maximum of 32 characters. Defaults None Command Modes CONFIG-INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1255
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL.
PAGE 1256
Example Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5.0.0 Introduced on the Z9000, S6000, S4820T, S4810, and MXL. Display all DSCP color maps. Dell# show qos dscp-color-map Dscp-color-map mapONE yellow 4,7 red 20,30 Dscp-color-map mapTWO yellow 16,55 Display a specific DSCP color map.
PAGE 1257
44 Routing Information Protocol (RIP) Routing information protocol (RIP) is a distance vector routing protocol. The Dell Networking operating software supports both RIP version 1 (RIPv1) and RIP version 2 (RIPv2) on the platform. The Dell Networking OS implementation of RIP is based on IETF RFCs 2453 and RFC 1058. For more information about configuring RIP, refer to the Dell Networking OS Configuration Guide.
PAGE 1258
clear ip rip Update all the RIP routes in the Dell Networking OS routing table. S3048–ON Syntax clear ip rip Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1259
• For a Port Channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. database (OPTIONAL) Enter the keyword database to display messages when there is a change to the RIP database. events (OPTIONAL) Enter the keyword events to debug only RIP protocol changes. trigger (OPTIONAL) Enter the keyword trigger to debug only RIP trigger extensions.
PAGE 1260
metric metric-value (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 1 to 16. The default is 1. route-map mapname (OPTIONAL) Enter the keywords route-map then the name of a configured route-map. Defaults Disabled. Metric: 1. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1261
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1262
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 7.7.1.0 Introduced on the E-Series. router rip — enters ROUTER mode on the switch. distance Assign a weight (for prioritization) to all routes in the RIP routing table or to a specific route.
PAGE 1263
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. default-metric — assigns one distance metric to all routes learned using the redistribute command. distribute-list in Configure a filter for incoming routing updates.
PAGE 1264
Related Commands Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.29.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. ip prefix-list — enters PREFIX-LIST mode and configures a prefix list.
PAGE 1265
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1266
Related Commands Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. ip split-horizon — sets the RIP routing updates to exclude routing prefixes. ip rip receive version To receive specific versions of RIP, set the interface.
PAGE 1267
Version Description 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information If you want the interface to receive both versions of RIP, use the ip rip receive version 1 2 command. Related Commands ip rip send version — sets the RIP version for sending RIP traffic on an interface. version — sets the RIP version the switch software uses. ip rip send version To send a specific version of RIP, set the interface.
PAGE 1268
Version Description 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To enable the interface to send both version of RIP packets, use the ip rip send version 1 2 command. Related Commands ip rip receive version — sets the RIP version for the interface to receive traffic. version — sets the RIP version for the switch software. ip split-horizon Enable split-horizon for RIP data on the interface.
PAGE 1269
maximum-paths Set RIP to forward packets over multiple paths. S3048–ON Syntax maximum-paths number To return to the default values, use the no maximum-paths commands. Parameters number Enter the number of paths. The range is from 1 to 16. The default is 4 paths. Defaults 4 Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1270
Parameters ip-address Enter the IP address, in dotted decimal format, of a router with which to exchange information. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 1271
Defaults No RIP network is configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1272
• For a Port Channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a VLAN, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific.
PAGE 1273
Parameters delay Specify a number of milliseconds as the delay interval. The range is from 8 to 50. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1274
Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1275
Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1276
level-2 (OPTIONAL) Enter the keywords level-2 to redistribute only IS-IS Level-2 routes. metric metric-value (OPTIONAL) Enter the keyword metric then a number as the metric value. The range is from 0 to 16. route-map mapname (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific.
PAGE 1277
route-map mapname (OPTIONAL) Enter the keywords route-map then the name of a configured route map. Defaults Not configured. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1278
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Usage Information To enable RIP, assign a network address using the network command.
PAGE 1279
Example Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. Dell(conf-router_rip)#show config ! router rip network 172.31.0.0 passive-interface GigabitEthernet 1/1 Dell(conf-router_rip)# show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated.
PAGE 1280
Usage Information Example Version Description 7.6.1.0 Introduced on the C-Series. pre- 6.2.1.1 Introduced on the E-Series. The following describes the show ip rip database command shown in the following example. Field Description Total number of routes in RIP database Displays the number of RIP routes stored in the RIP database. 100.10.10.0/24 directly connected Lists the routes directly connected. 150.100.0.0 redistributed Lists the routes learned through redistribution. 209.9.16.0/24...
PAGE 1281
The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the S-Series. 7.7.1.0 Introduced on the C-Series. 7.6.1.
PAGE 1282
flush Defaults Enter the number of seconds to specify the time interval during which the route is advertised as unreachable. When this interval expires, the route is flushed from the routing table. The flush value should be greater than the update value. The range is from zero (0) to 4294967295. The default is 240 seconds. • update = 30 seconds • invalid = 180 seconds • holddown = 180 seconds • flush = 240 seconds Command Modes ROUTER RIP Command History This guide is platform-specific.
PAGE 1283
2 Enter the keyword 2 to specify RIP version 2. Defaults The Dell Networking OS sends RIPv1 and receives RIPv1 and RIPv2. Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1284
45 Remote Monitoring (RMON) The Dell Networking operating software remote monitoring (RMON) is implemented on the S3048–ON platform. Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection.
PAGE 1285
interval Time, in seconds, the alarm monitors the MIB variables; this is the alarmSampleType in the RMON alarm table. The range is from 5 to 3600 seconds. delta Enter the keyword delta to test the change between MIB variables. This is the alarmSampleType in the RMON alarm table. absolute Enter the keyword absolute to test each MIB variable directly. This is the alarmSampleType in the RMON alarm table.
PAGE 1286
rmon collection history Enable the RMON MIB history group of statistics collection on an interface. S3048–ON Syntax rmon collection history {controlEntry integer} [owner name] [buckets number] [interval seconds] To remove a specified RMON history group of statistics collection, use the no rmon collection history {controlEntry integer} command. Parameters controlEntry integer Enter the keyword controlEntry to specify the RMON group of statistics using a value.
PAGE 1287
rmon collection statistics Enable RMON MIB statistics collection on an interface. S3048–ON Syntax rmon collection statistics {controlEntry integer} [owner name] To remove RMON MIB statistics collection on an interface, use the no rmon collection statistics {controlEntry integer} command. Parameters controlEntry integer Enter the keyword controlEntry to specify the RMON group of statistics using a value. Then enter an integer value from 1 to 65535 that identifies the RMON Statistic Table.
PAGE 1288
rmon event Add an event in the RMON event table. S3048–ON Syntax rmon event number [log] [trap community] [description string] To disable RMON on an interface, use the no rmon event number command. Parameters number Assign an event number in integer format. The range is from 1 to 65535. You must ensure that the value you enter is unique in the RMON event table. log (OPTIONAL) Enter the keyword log to generate an RMON event log.
PAGE 1289
rmon hc-alarm Set an alarm on any MIB object. S3048–ON Syntax rmon hc-alarm number variable interval {delta | absolute} rising-threshold value event-number falling-threshold value event-number [owner string] To disable the alarm, use the no rmon hc-alarm number command. Parameters number Enter the alarm integer number from 1 to 65535. The value must be unique in the RMON alarm table. variable The MIB object to monitor. The variable must be in the SNMP OID format; for example, 1.3.6.1.2.1.1.
PAGE 1290
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. show rmon Display the RMON running status including the memory usage. S3048–ON Syntax show rmon Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1291
event table: 500 entries, 206000 bytes log table: 2 entries, 552 bytes Dell# show rmon alarms Display the contents of the RMON alarm table. S3048–ON Syntax Parameters show rmon alarms [index] [brief] index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON alarm table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1292
alarm status: OK Dell# Example (Brief) Dell#show rmon alarm br index SNMP OID -------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.1.3 3 1.3.6.1.2.1.1.3 4 1.3.6.1.2.1.1.3 5 1.3.6.1.2.1.1.3 6 1.3.6.1.2.1.1.3 7 1.3.6.1.2.1.1.3 8 1.3.6.1.2.1.1.3 9 1.3.6.1.2.1.1.3 10 1.3.6.1.2.1.1.3 11 1.3.6.1.2.1.1.3 12 1.3.6.1.2.1.1.3 13 1.3.6.1.2.1.1.3 14 1.3.6.1.2.1.1.3 15 1.3.6.1.2.1.1.3 16 1.3.6.1.2.1.1.3 17 1.3.6.1.2.1.1.3 18 1.3.6.1.2.1.1.3 19 1.3.6.1.2.1.1.3 20 1.3.6.1.2.1.1.3 21 1.3.6.1.2.1.1.3 22 1.3.6.1.2.1.1.
PAGE 1293
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1294
14 15 16 17 18 19 20 21 22 Dell# 14 15 16 17 18 19 20 21 22 show rmon hc-alarm Display the contents of RMON High-Capacity alarm table. S3048–ON Syntax show rmon hc-alarm [index] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON High-Capacity alarm table in an easy-to-read format. Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1295
sample interval: 10 sample type: delta value. value: 0, value status: positive alarm type: rising or falling alarm. alarm rising threshold value: positive. rising threshold: 500, RMON event index: 3 alarm falling threshold value: positive. falling threshold: 300, RMON event index: 4 alarm sampling failed 0 times. alarm owner: alarm storage type: non-volatile. alarm status: OK Dell# Example (Brief) Dell#show rmon hc-alarm brief index SNMP OID ---------------------------------1 1.3.6.1.2.1.1.3 2 1.3.6.1.2.1.
PAGE 1296
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Example (Index) Dell#show rmon history 6001 RMON history control entry 6001 interface: ifIndex.
PAGE 1297
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. Usage Information The log table has a maximum of 500 entries.
PAGE 1298
The following is a list of the Dell Networking OS version history for this command. Example (Index) 1298 Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1299
Example (Brief) Dell#show rmon statistics br index ifIndex interface ---------------------------------------6001 100974631 GigabitEthernet 2/2 6002 100974631 GigabitEthernet 2/2 6003 101236775 GigabitEthernet 2/1 6004 101236775 GigabitEthernet 2/1 9001 134529054 GigabitEthernet 3/2 9002 134529054 GigabitEthernet 3/2 9003 134791198 GigabitEthernet 3/1 9004 134791198 GigabitEthernet 3/1 Dell# Remote Monitoring (RMON) 1299
PAGE 1300
46 Rapid Spanning Tree Protocol (RSTP) The Dell Networking operating software implementation of rapid spanning tree protocol (RSTP) is based on the IEEE 802.1w standard spanning-tree protocol. The RSTP algorithm configures connectivity throughout a bridged local area network (LAN) that is comprised of LANs interconnected by bridges. Dell Networking OS supports RSTP. bridge-priority Set the bridge priority for RSTP.
PAGE 1301
Related Commands protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol. Syntax debug spanning-tree rstp [all | bpdu interface {in | out} | events] To disable debugging, use the no debug spanning-tree rstp command. Parameters all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu interface {in | out} (OPTIONAL) Enter the keyword bpdu to debug the bridge protocol data units.
PAGE 1302
Example Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell#debug spanning-tree rstp bpdu gigabitethernet 2/1 ? in Receive (in) out Transmit (out) description Enter a description of the rapid spanning tree. Syntax description {description} To remove the description, use the no description {description} command. Parameters description Enter a description to identify the rapid spanning tree (80 characters maximum).
PAGE 1303
disable Disable RSTP globally on the system. Syntax disable To enable Rapid Spanning Tree Protocol, use the no disable command. Defaults RSTP is disabled. Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.
PAGE 1304
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1305
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Added the milli-second option to the S-Series. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1306
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1307
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information RSTP is not enabled when you enter RSTP mode. To enable RSTP globally on the system, use the no disable command from RSTP mode. Example Dell(conf)#protocol spanning-tree rstp Dell(config-rstp)##no disable Related Commands disable — disables RSTP globally on the system. show config View the current configuration for the mode.
PAGE 1308
show spanning-tree rstp Display the RSTP configuration. Syntax show spanning-tree rstp [brief] [guard] Parameters Command Modes Command History Usage Information Example (Brief) 1308 brief (OPTIONAL) Enter the keyword brief to view a synopsis of the RSTP configuration information. guard (OPTIONAL) Enter the keyword guard to display the type of guard enabled on an RSTP interface and the current port state. • EXEC • EXEC Privilege Version Description 9.8(0.0P5) Introduced on the S4048-ON.
PAGE 1309
Root Bridge hello time 4, max age 20, forward delay 15 Bridge ID Priority 16384, Address 0001.e801.6aa8 Configured hello time 2, max age 20, forward delay 15 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------- ------- --- ------- -------------------- -------Gi 4/2 128.418 128 20000 FWD 20000 16384 0001.e801.6aa8 128.418 Gi 4/1 128.419 128 20000 FWD 20000 16384 0001.e801.6aa8 128.419 Gi 4/8 128.426 128 20000 FWD 20000 8192 0001.e805.e306 128.130 Gi 4/9 128.
PAGE 1310
spanning-tree rstp Configure an RSTP interface with one of these settings: port cost, edge port with optional bridge port data unit (BPDU) guard, port priority, loop guard, or root guard. Syntax spanning-tree rstp {cost port-cost | edge-port [bpduguard [shutdown-onviolation]] | priority priority | {loopguard | rootguard}} Parameters cost port-cost Enter the keyword cost then the port cost value. The range is from 1 to 200000.
PAGE 1311
Usage Information Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.2.1 Added support for the optional guard keyword on the C-Series, S-Series, and ESeries TeraScale. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced the hardware shutdown-on-violation options. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 7.4.1.
PAGE 1312
tc-flush-standard Enable the MAC address flushing after receiving every topology change notification. Syntax tc-flush-standard To disable, use the no tc-flush-standard command. Defaults Disabled Command Modes CONFIGURATION (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1313
47 Software-Defined Networking (SDN) Dell Networking operating software supports Software-Defined Networking (SDN). For more information, refer to the SDN Deployment Guide.
PAGE 1314
48 Security The commands in this chapter are available on Dell Networking OS. For configuration details, see the Security chapter in the Dell Networking OS Configuration Guide. NOTE: Dell Networking OS implements LEAP with MSCHAP v2 supplicant. AAA Accounting Commands AAA Accounting enables tracking of services that users are accessing and the amount of network resources being consumed by those services.
PAGE 1315
wait-start Enter the keywords wait-start to ensure that the TACACS+ security server acknowledges the start notice before granting the user’s process request. stop-only Enter the keywords stop-only to instruct the TACACS+ security server to send a “stop record accounting” notice at the end of the requested user process. tacacs+ Enter the keyword tacacs+ to use TACACS+ data for accounting. The Dell Networking OS currently only supports TACACS+ accounting.
PAGE 1316
tacacs-server host — specifies a TACACS+ server host. accounting Apply an accounting method list to terminal lines. Syntax accounting {exec | commands {level | role role-name} method-list Parameters exec Enter the keyword exec to apply an EXEC level accounting method list.
PAGE 1317
To permit accounting records to users with user name value of NULL, use the no aaa accounting suppress null-username command. Defaults Accounting records are recorded for all users. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.
PAGE 1318
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. You can use this command to configure the group of Radius servers used for Authentication, Authorization, and Accounting purposes.
PAGE 1319
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.0 Introduced on the E-Series. Usage Information This command steps through all active sessions and then displays the accounting records for the active account functions.
PAGE 1320
Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.3.1.
PAGE 1321
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.0) Added support for roles on the Z9000, S6000, S4820T, S4810, MXL 9.2(1.0) Introduced on the Z9500. 9.0.
PAGE 1322
Usage Information Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the E-Series. By default, the aaa authorization commands command configures the system to check both EXEC level and CONFIGURATION level commands. Use the command no aaa authorization configcommands to enable only EXEC-level command checking. aaa authorization exec Set parameters that restrict (or permit) a user’s access to EXEC-level commands.
PAGE 1323
privilege level (CONFIGURATION mode) Change the access or privilege level of one or more commands. Syntax privilege mode {level level command | reset command} To delete access to a level and command, use the no privilege mode level level command command.
PAGE 1324
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. To define a password for the level to which you are assigning privilege or access, use the enable password command. privilege level (LINE mode) Change the access level for users on the terminal lines. Syntax privilege level level To delete access to a terminal line, use the no privilege level level command. Parameters level level Enter the keyword level then a number for the access level. The range is from 0 to 15.
PAGE 1325
Obscure Password Commands To enable the obscure password, use the following commands. service obscure-passwords Enable the obscuring of passwords and keys. Syntax service obscure-passwords Enable the obscuring of passwords and keys, including RADIUS, TACACS+ keys, router authentication strings, VRRP authentication, use the service obscure-passwords command. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1326
Authentication and Password Commands To manage access to the system, use the following the commands. aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). Syntax aaa authentication enable {default | method-list-name} method [... method2] To return to the default setting, use the no aaa authentication enable {default | methodlist-name} method [... method2] command.
PAGE 1327
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.0 Introduced on the E-Series. By default, the Enable password is used. If you configure aaa authentication enable default, Dell Networking OS uses the methods defined for Enable access instead. Methods configured with the aaa authentication enable command are evaluated in the order they are configured.
PAGE 1328
• ... method4 tacacs+: use the TACACS+ servers configured with the tacacs-server host command. (OPTIONAL) Enter up to four additional methods. In the event of a “no response” from the first method, the system applies the next configured method (up to four configured methods). Defaults Not configured (that is, no authentication is performed). Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1329
Connections to the SSH server work with the following login mechanisms: local, radius, and tacacs. Related Commands login authentication — enables AAA login authentication on the terminal lines. password — creates a password. radius-server host — specifies a RADIUS server host. tacacs-server host — specifies a TACACS+ server host. access-class Restrict incoming connections to a particular IP address in a defined IP access control list (ACL).
PAGE 1330
enable password Change the password for the enable command. Syntax enable password [level level] [encryption-type] password To delete a password, use the no enable password [encryption-type] password [level level] command. Parameters level level (OPTIONAL) Enter the keyword level then a number as the level of access. The range is from 1 to 15. encryption-type (OPTIONAL) Enter the number 7 or 0 as the encryption type. Enter a 7 then a text string as the hidden password.
PAGE 1331
• Start with a letter, not a number. • Passwords can have a regular expression as the password. To create a password with a regular expression in it, use CNTL + v prior to entering regular expression. For example, to create the password abcd]e, you type “abcd CNTL v ]e”. When the password is created, you do not use the CNTL + v key combination and enter “abcd]e”. NOTE: The question mark (?) and the tilde (~) are not supported characters.
PAGE 1332
Usage Information Version Description pre-6.1.1.0 Introduced on the E-Series. Only Dell Networking Technical Support staff use this command. enable secret Change the password for the enable command. Syntax enable secret [level level] [encryption-type] password To delete a password, use the no enable secret [encryption-type] password [level level] command. Parameters level level (OPTIONAL) Enter the keyword level then a number as the level of access. The range is from 1 to 15.
PAGE 1333
Usage Information To control access to command modes, use this command to define a password for a level and use the privilege level (CONFIGURATION mode) command. Passwords must meet the following criteria: • Start with a letter, not a number. • Passwords can have a regular expression as the password. To create a password with a regular expression in it, use CNTL + v prior to entering regular expression. For example, to create the password abcd]e, you type “abcd CNTL v ]e”.
PAGE 1334
Usage Information Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. If you configure the aaa authentication login default command, the login authentication default command automatically is applied to all terminal lines.
PAGE 1335
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series.
PAGE 1336
locking out sessions on the Telnet or SSH sessions for which there has been a consecutive failed login attempts. The console is not locked out. characterrestriction (OPTIONAL) Enter the keywords character-restriction to indicate a character restriction for the password. upper number (OPTIONAL) Enter the keyword upper then the upper number. The range is from 0 to 31. lower number (OPTIONAL) Enter the keyword lower then the lower number. The range is from 0 to 31.
PAGE 1337
Example In the following example, after 5 un-successful login attempts, the session (SSH/TELNET) goes into a locked state for 5 minutes. If all the 10 sessions are locked out with 5 un-successful attempts in each session, no users can login during the lockout-period. Dell(conf)#password-attributes max-retry 5 lockout-period 5 Related Commands password — specifies a password for users on terminal lines. service password-encryption Encrypt all passwords configured in Dell Networking OS.
PAGE 1338
show privilege View your access level. Syntax show privilege Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON.
PAGE 1339
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Example Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Added support for roles on the Z9500. 9.5(0.
PAGE 1340
timeout login response Specify how long the software waits for the login input (for example, the user name and password) before timing out. Syntax timeout login response seconds To return to the default values, use the no timeout login response command. Parameters seconds Enter a number of seconds the software waits before logging you out. The range is: • VTY: the range is from 1 to 30 seconds, the default is 30 seconds.
PAGE 1341
If you do not want a specific user to enter a password, use the nopassword option. To delete authentication for a user, use the no username name command. Parameters name Enter a text string for the name of the user up to 63 characters. access-class access-list-name Enter the keywords access-class then the name of a configured access control list (either an IP access control list or MAC access control list). nopassword Enter the keyword nopassword to specify that the user should not enter a password.
PAGE 1342
Version Description 7.7.1.0 Added support for the secret option and the MD5 password encryption. Extended the name from 25 to 63 characters. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information To view the defined user names, use the show running-config user command. Related Commands password — specifies a password for users on terminal lines. show running-config — views the current configuration.
PAGE 1343
Version Description pre-6.2.1.0 Introduced on the E-Series. ip radius source-interface Specify an interface’s IP address as the source IP address for RADIUS connections. Syntax ip radius source-interface interface To delete a source interface, use the no ip radius source-interface command. Parameters interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1344
radius-server deadtime Configure a time interval during which non-responsive RADIUS servers to authentication requests are skipped. Syntax radius-server deadtime seconds To disable this function or return to the default value, use the no radius-server deadtime command. Parameters seconds Enter a number of seconds during which non-responsive RADIUS servers are skipped. The range is from 0 to 2147483647 seconds. The default is 0 seconds.
PAGE 1345
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Introduced on the S-Series and Z-Series. Example Dell(conf)#radius-server group group1 Dell(conf-radius-group)#radius-server host 1.1.1.1 key secret Dell(conf-radius-group)#radius-server host 2.2.2.
PAGE 1346
key [encryptiontype] key (OPTIONAL) Enter the keyword key then an optional encryption-type and a string up to 42 characters long as the authentication key. The RADIUS host server uses this authentication key and the RADIUS daemon operating on this switch. For the encryption-type, enter either zero (0) or 7 as the encryption type for the key entered. The options are: • 0 is the default and means the password is not encrypted and stored as clear text. • 7 means that the password is encrypted and hidden.
PAGE 1347
You can use duplicate host names or IP addresses among RADIUS groups. However, you cannot use duplicate host names or IP addresses within the same RADIUS group. If a VRF is not configured on the RADIUS group, then servers configured in the group are considered to be on the default VRF. RADIUS servers that are configured in the CONFIGURATION mode are also considered to be on the default VRF.
PAGE 1348
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4(0.
PAGE 1349
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.
PAGE 1350
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1351
Related Commands Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.2.1.0 Introduced on the E-Series. radius-server host — configures a RADIUS host. TACACS+ Commands Dell Networking OS supports TACACS+ as an alternate method for login authentication.
PAGE 1352
gigabitethernet 1/40 Dell(conf)#exit Dell(conf)#aaa tacacsgroup group1 Related Commands aaa authentication login — specifies the login authentication method. tacacs-server key — configures a TACACS+ key for the TACACS server. debug tacacs+ To assist with troubleshooting, view TACACS+ transactions. Syntax debug tacacs+ To disable debugging of TACACS+, use the no debug tacacs+ command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific.
PAGE 1353
• For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. • For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured.
PAGE 1354
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z-Series. Usage Information You can associate a TACACS server group with a VRF. Example Dell(conf)#tacacs-server group group1 Dell(conf-tacacs-group)#tacacs-server host 1.1.1.
PAGE 1355
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1356
tacacs-server key Configure a key for communication between a TACACS+ server and a client. Syntax tacacs-server key [encryption-type] key To delete a key, use the no tacacs-server key key command. Parameters encryption-type key (OPTIONAL) Enter either zero (0) or 7 as the encryption type for the key entered. The options are: • 0 is the default and means the key is not encrypted and stored as clear text. • 7 means that the key is encrypted and hidden.
PAGE 1357
To delete the association between a TACACS server group and a VRF and source interface, use the no tacacs-server vrf vrf-name [source-interface interface] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate a TACACS server group with that VRF. interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1358
Port Authentication (802.1X) Commands An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only Extensible Authentication Protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic passes through the port. Dell Networking OS supports RADIUS and Active Directory environments using 802.1X Port Authentication.
PAGE 1359
Related Commands Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x authentication (Interface) — enables dot1x on an interface. dot1x authentication (Interface) Enable dot1x on an interface; dot1x must be enabled both globally and at the interface level. Syntax dot1x authentication To disable dot1x on an interface, use the no dot1x authentication command. Defaults Disabled.
PAGE 1360
max-attempts number (OPTIONAL) Enter the keywords max-attempts then number of attempts desired before authentication fails. The range is from 1 to 5. The default is 3. Defaults 3 attempts Command Modes CONFIGURATION (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1361
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x guest-vlan Configure a guest VLAN for limited access users or for devices that are not 802.
PAGE 1362
If a device does not respond within 30 seconds, it is assumed that the device is not 802.1X capable. Therefore, a guest VLAN is allocated to the interface and authentication for the device occurs at the next re-authentication interval (dot1x reauthentication). If the host fails authentication for the designated number of times, the authenticator places the port in authentication failed VLAN (dot1x auth-fail-vlan).
PAGE 1363
dot1x max-eap-req Configure the maximum number of times an extensive authentication protocol (EAP) request is transmitted before the session times out. Syntax dot1x max-eap-req number To return to the default, use the no dot1x max-eap-req command. Parameters number Enter the number of times an EAP request is transmitted before a session timeout. The range is from 1 to 10. The default is 2. Defaults 2 Command Modes INTERFACE Command History This guide is platform-specific.
PAGE 1364
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1365
Version Description 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x reauthentication Enable periodic re-authentication of the client. Syntax dot1x reauthentication [interval seconds] To disable periodic re-authentication, use the no dot1x reauthentication command. Parameters interval seconds (Optional) Enter the keyword interval then the interval time, in seconds, after which re-authentication is initiated.
PAGE 1366
Parameters number Enter the permitted number of re-authentications. The range is from 1 to 10. The default is 2. Defaults 2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON.
PAGE 1367
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-Series and S-Series. 7.4.1.0 Introduced on the E-Series. dot1x supplicant-timeout Configure the amount of time after which exchanges with the supplicant time-out. Syntax dot1x supplicant-timeout seconds To return to the default, use theno dot1x supplicant-timeout command.
PAGE 1368
To return to the default, use the no dot1x tx-period command. Parameters seconds Enter the interval time, in seconds, that EAPOL PDUs are transmitted. The range is from 1 to 65535 (1 year). The default is 30. Defaults 30 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1369
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T.
PAGE 1370
Auth-Fail VLAN id: Auth-Fail Max-Attempts: Mac-Auth-Bypass: Mac-Auth-Bypass Only: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: Dell# NONE NONE Disable Disable 30 seconds 60 seconds 2 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Initialize Initialize SSH Server and SCP Commands Dell Networking OS supports secure shell (SSH) protocol versions 1.5 and 2.0.
PAGE 1371
Usage Information Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.0 Added support for FIPS mode on the S4810. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. The host keys are required for key-exchange by the SSH server.
PAGE 1372
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL debug ip ssh Enables collecting SSH debug information. Syntax debug ip ssh {client | server} To disable debugging, use the no debug ip ssh {client | server} command. Parameters client Enter the keyword client to enable collecting debug information on the client.
PAGE 1373
ip scp topdir Identify a location for files used in secure copy transfer. Syntax ip scp topdir directory To return to the default setting, use the no ip scp topdir command. Parameters directory Enter a directory name. Defaults The internal flash (flash:) is the default directory. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1374
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1375
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. ip ssh hostbased-authentication Enable hostbased-authentication for the SSHv2 server. Syntax ip ssh hostbased-authentication enable To disable hostbased-authentication for SSHv2 server, use the no ip ssh hostbasedauthentication enable command.
PAGE 1376
• checking client host-keys is done with the file specified in the ip ssh pub-key-file command. NOTE: Administrators must specify the two files (rhosts and pub-key-file) to configure host-based authentication. Related Commands ip ssh pub-key-file — public keys of trusted hosts from a file. ip ssh rhostsfile — trusted hosts and users for rhost authentication. ip ssh key-size Configure the size of the server-generated RSA SSHv1 key.
PAGE 1377
To disable password-authentication, use the no ip ssh password-authentication enable command. Parameters enable Enter the keyword enable to enable password-authentication for the SSH server. Defaults Enabled Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1378
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. This command specifies the file used for the host-based authentication.
PAGE 1379
Command Modes CONFIGURATION mode Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.
PAGE 1380
Usage Information This command specifies the rhost file used for host-based authentication. This creates/ file overwrites the flash:/ADMIN_DIR/ssh/shosts file and deletes the user-specified file. Even though this command is a global configuration command, it does not appear in the running configuration because you only need to run this command once. This file contains hostnames and usernames, for which hosts and users, rhost-authentication can be allowed.
PAGE 1381
ip ssh server Configure an SSH server. SSH server is enabled by default. Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative.
PAGE 1382
When FIPS is enabled, the default HMAC algorithm is hmac-sha1-96. When FIPS is not enabled, the default HMAC algorithms are the following: kex key-exchangealgorithm • hmac-md5 • hmac-md5-96 • hmac-sha1 • hmac-sha1-96 • hmac-sha2-256 • hmac-sha2-256-96 Enter the keyword kex and then a space-delimited list of key exchange algorithms supported by the SSH server.
PAGE 1383
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.5(0.1) Introduced the cipher , kex and mac options on the Z9500. 9.5(0.
PAGE 1384
vrf vrf-name Enter the key word vrf followed by the VRF name to configure an SSH server on that VRF. Defaults None Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1385
• For a Null interface, enter the keyword null then the Null interface number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 1386
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S-Series and Z9000. Usage Information If you configure a VRF for an SSH session, then you need not explicitly mention the same VRF for the SSH client sessions intended for that VRF. The vrf attribute in the ip ssh vrf command is applicable for both the SSH client as well as the COPY (SCP) commands.
PAGE 1387
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information This command is useful if the remote SSH client implements Strict Host Key Checking. You can copy the host key to your list of known hosts.
PAGE 1388
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Example Dell#show ip ssh SSH server : enabled. SSH server version : v1 and v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256cbc,aes128-ctr,aes192-ctr,aes256-ctr. SSH server macs : hmac-md5,hmac-md5-96,hmac-sha1,hmacsha1-96,hmac-sha2-256,hmac-sha2-256-96.
PAGE 1389
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information This command displays the contents of the flash://ADMIN_DIRssh/knownhosts file. Example Dell# show ip ssh client-pub-keys 4.8.1.
PAGE 1390
Version Description 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. pre-6.1.1.0 Introduced on the E-Series. Usage Information This command displays the contents of the flash:/ADMIN_DIR/ssh/authorized-keys.username file.
PAGE 1391
ipv6-address prefixlength (OPTIONAL) Enter the IPv6 address in the x:x:x:x::x format then the prefix length in the /x format. The range is from /0 to /128. NOTE: The :: notation specifies successive hexadecimal fields of zeros. -c encryption cipher Enable the “FIPS mode enable", this mode will support only v2 client. "no fips mode enable"(disable) will support v1 & v2 client. This comment is applicable for both ciphers & HMAC algorithms: • 3des-cbc: Force ssh to use 3des-cbc encryption cipher.
PAGE 1392
Version Description 9.5(0.1) Added support for the following ciphers and HMAC alogorithms on the Z9000, S6000, S4820T, S4820T. S6000–ON. • aes128-cbc • aes192-cbc • aes256-cbc • aes128-ctr • aes192-ctr • aes256-ctr • hmac-sha2-256 • hmac-sha2-256-96 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.12.
PAGE 1393
clear ip dhcp snooping Clear the DHCP binding table. Syntax clear ip dhcp snooping binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1394
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.4.(0.0) Added support for VRF. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping Enable DHCP Snooping globally. Syntax [no] ip dhcp snooping Defaults Disabled.
PAGE 1395
ip dhcp snooping binding Create a static entry in the DHCP binding table. Syntax Parameters Defaults Command Modes Command History [no] ip dhcp snooping binding mac address vlan-id vlan-id ip ip-address interface type slot/port lease number mac address Enter the keyword mac then the MAC address of the host to which the server is leasing the IP address. vlan-id vlan-id Enter the keywords vlan-id then the VLAN to which the host belongs. The range is from 2 to 4094.
PAGE 1396
Related Commands Version Description 7.8.1.0 Introduced on the C-Series and S-Series. show ip dhcp snooping — displays the contents of the DHCP binding table. ip dhcp snooping database Delay writing the binding table for a specified time. Syntax ip dhcp snooping database write-delay minutes Parameters minutes The range is from 5 to 21600. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1397
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping trust Configure an interface as trusted.
PAGE 1398
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000–ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1399
NOTE: Learning only happens if there is a trusted port in the VLAN. Related Commands ip dhcp snooping trust — configures an interface as trusted. show ip dhcp snooping Display the contents of the DHCP binding table. Syntax show ip dhcp snooping binding Defaults none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1400
• show users • username aaa authorization role-only Configure authentication to use the user’s role only when determining if access to commands is permitted. Syntax aaa authorization role-only To return to the default setting, use the no aaa authentication role-only command. Parameters name Enter a text string for the name of the user up to 63 characters. It cannot be one of the system defined roles (sysadmin, secadmin, netadmin, netoperator).
PAGE 1401
Defaults 15 Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.
PAGE 1402
interface for INTERFACE modes line for LINE mode route-map for Route-map mode router for Router mode addrole Enter the keyword addrole to add permission to the command. You cannot add or delete rights for the sysadmin role. deleterole Enter the keyword deleterole to remove access to the command. You cannot add or delete rights for the sysadmin role. role-name Enter a text string for the name of the user role up to 63 characters.
PAGE 1403
Defaults none Command Modes EXEC Privilege Command History Examples Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.5(0.
PAGE 1404
secadmin sysadmin netoperator testadmin Related Commands Exec Config Exec Config Interface Line Router IP Route-map Protocol MAC netadmin Exec Config Interface Line Router IP Route-map Protocol MAC userrole, username userrole Create user roles for the role-based security model. Syntax userrole name inherit existing-role-name To delete a role name, use the no userrole name command. Note that the reserved role names may not be deleted.
PAGE 1405
NOTE: If you inherit a user role, you cannot modify or delete the inheritance. If you want to change or remove the inheritance, delete the user role and create it again. If the user role is in use, you cannot delete the user role. role mode { { { addrole | deleterole } role-name } | reset } command – Modifies (adds or deletes) command permissions for newly created user roles and system defined roles.
PAGE 1406
49 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell Networking OS Configuration Guide Service Provider Bridging chapter. This chapter includes command line information (CLI) for the Dell Networking operating software Layer 2 Protocol Tunneling (L2PT). L2PT enables protocols to tunnel through an 802.1q tunnel. Dell Networking OS supports L2PT on Dell Networking OS.
PAGE 1407
• For a Port Channel interface, enter the keywords port-channel then a number. The range is from 1 to 128. in | out | both Enter the keyword in, out, or both to debug incoming interfaces, outgoing interfaces, or both incoming and outgoing interfaces. vlan vlan-id Enter the keyword vlan then the VLAN ID. The range is from 1 to 4094. count value Enter the keyword count then the number of debug outputs. The range is from 1 to 100. Defaults Debug disabled.
PAGE 1408
Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guid. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.11.
PAGE 1409
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on the C-Series, and S-Series. 7.4.1.0 Introduced Usage Information When you enable VLAN-Stacking, no protocol packets are tunneled. Related Command show protocol-tunnel — displays tunneling information for all VLANs.
PAGE 1410
protocol-tunnel rate-limit Enable traffic rate limiting per box. Syntax protocol-tunnel rate-limit rate To reset the rate limit to the default, use the no protocol-tunnel rate-limit rate command. Parameters rate Enter the rate in frames per second. The range is from 75 to 3000. The default is 75. Defaults 75 frames per second. Command Modes CONF-IF-VLAN-STACK Command History This guide is platform-specific.
PAGE 1411
show protocol-tunnel Display protocol tunnel information for all or a specified VLAN-Stack VLAN. Syntax Parameters show protocol-tunnel [vlan vlan-id] vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID to display information for the one VLAN. The range is from 1 to 4094. Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1412
Gi1/2 Dell# Related Commands 1412 2 STP, PVST show running-config — displays the current configuration.
PAGE 1413
50 sFlow The Dell Networking operating software (OS) supports sFlow commands on Dell Networking OS. Dell Networking operating software sFlow monitoring system includes an sFlow Agent and an sFlow Collector. • The sFlow Agent combines the flow samples and interface counters into sFlow datagrams and forwards them to the sFlow Collector. • The sFlow Collector analyses the sFlow Datagrams received from the different devices and produces a network-wide view of traffic flows.
PAGE 1414
To delete a configured collector, use the no sflow collector {ip-address | ipv6-address} agent-addr {ipv4-address | ipv6-address} [number [max-datagram-size number]] | [max-datagram-size number] [vrf management] command. Parameters sflow collector ipaddress | ipv6address Enter the IP address of the collector in dotted decimal format for IPv4 or x:x:x:x::x format for IPv6.
PAGE 1415
Usage Information Version Description 7.6.1.0 Introduced on the C-Series. 6.5.1.0 Expanded the no form of the command to mirror the syntax used to configure. 6.2.1.1 Introduced on the E-Series. You can configure up to two sFlow collectors (IPv4 or IPv6). If two collectors are configured, traffic samples are sent to both. The sFlow agent address is carried in a field in SFlow packets and is used by the collector to identify the sFlow agent.
PAGE 1416
Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information sFlow is disabled by default. In addition to this command, sFlow needs to be enable on individual interfaces where sFlow sampling is desired.
PAGE 1417
sflow extended-switch enable Enable packing information on a switch only. Syntax sflow extended-switch enable To disable packing information, use the no sflow extended-switch [enable] command. Parameters enable Enter the keyword enable to enable global extended information. Defaults Disabled. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1418
To reset the maximum header size of a packet, use the[no] sflow max-header-size extended command. Parameters extended Defaults 128 bytes Command Modes CONFIGURATION Enter the keyword extended to copy 256 bytes from the sample packets to sFlow datagram. INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1419
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series.
PAGE 1420
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information This command sets the counter polling interval for an interface. Related Commands sflow polling-interval (Global) — globally sets the polling interval.
PAGE 1421
Version Description 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 7.4.1.0 Introduced on the E-Series. Usage Information Sample-rate is the average number of packets skipped before the sample is taken. This command changes the global default sampling rate. You can configure an interface to use a different sampling rate than the global sampling rate.
PAGE 1422
Version Description 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information This command changes the sampling rate for an interface. By default, the sampling rate of an interface is set to the same value as the current global default sampling rate. If the value entered is not a correct power of 2, the command generates an error message with the previous and next power-of-2 value.
PAGE 1423
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.2.1.0 Introduced on S-Series Stacking. 8.1.1.0 Introduced on the E-Series ExaScale. 7.7.1.0 Introduced on the S-Series. 7.6.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1424
51 Simple Network Management Protocol (SNMP) and Syslog This chapter contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on Dell Networking OS. SNMP Commands The following SNMP commands are available in the Dell Networking OS. The simple network management protocol (SNMP) is used to communicate management information between the network management stations and the agents in the network elements.
PAGE 1425
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1426
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1427
Version Description 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information The following Example displays a group named ngroup. The ngroup has a security model of version 3 (v3) with authentication (auth), the read and notify name is nview with no write view name specified, and finally the row status is active.
PAGE 1428
storage-type: nonvolatile active Authentication Protocol: None Privacy Protocol: None Dell# snmp ifmib ifalias long Display the entire description string through the Interface MIB, which would be truncated otherwise to 63 characters. Syntax snmp ifmib ifalias long Defaults Interface description truncated beyond 63 characters. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1429
snmp-server community Configure a new community string access for SNMPv1 v2 and v3.
PAGE 1430
Usage Information The following example configures a community named public that is mapped to the security named guestuser with Read Only (ro) permissions. The security-name parameter maps the community string to an SNMPv3 user/security name as defined by the community MIB.
PAGE 1431
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1432
notification-option For the envmon notification-type, enter one of the following optional parameters: • cam-utilization • fan • supply • temperature For the snmp notification-type, enter one of the following optional parameters: • authentication • coldstart • linkdown • linkup • syslog-reachable • syslog-unreachable Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1433
Usage Information Dell Networking OS supports up to 16 SNMP trap receivers. If you do not configure this command, traps that controlled by this command are not sent. If you do not specify a notification-type and notification-option, all traps are enabled. Related Commands snmp-server community — enables SNMP and sets the community string. snmp-server engineID Configure the name for both the local and remote SNMP engines on the router.
PAGE 1434
Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Changing the value of the SNMP Engine ID has important side effects. A user’s password (entered on the command line) is converted to a message digest algorithm (MD5) or secure hash algorithm (SHA) security digest. This digest is based on both the password and the local Engine ID. The command line password is then destroyed, as required by RFC 2274.
PAGE 1435
noauth (OPTIONAL) Enter the keyword noauth to specify no authentication of a packet. priv (OPTIONAL) Enter the keyword priv to specify both authentication and then scrambling of the packet. read name (OPTIONAL) Enter the keyword read then a name (a string of up to 20 characters long) as the read view name. The default is GlobalView and is assumed to be every object belonging to the internet (1.3.6.1) OID space.
PAGE 1436
NOTE: The number of configurable groups is limited to 16 groups. Example Dell#conf Dell(conf)# snmp-server group harig 3 priv read rview Dell# Related Commands show snmp group — displays the group name, security model, view status, and storage type of each group. show running-config — displays the SNMP running configuration. snmp-server host Configure the recipient of an SNMP trap operation.
PAGE 1437
priv (OPTIONAL) Enter the keyword priv to specify both authentication and then scrambling of the packet. community-string Enter a text string (up to 20 characters long) as the name of the SNMP community. NOTE: For version 1 and version 2c security models, this string represents the name of the SNMP community. The string can be set using this command; however, Dell Networking OS recommends setting the community string using the snmp-server community command before executing this command.
PAGE 1438
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.1(0.0) Added support for config and ecmp traps. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.0 Added support for VRRP traps. 7.6.1.0 Added support for STP and xSTP notification types. Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1439
snmp-server community — configures a new community SNMPv1 or SNMPv2c. snmp-server location Configure the location of the SNMP server. Syntax snmp-server location text To delete the SNMP location, use the no snmp-server location command. Parameters text Enter an alpha-numeric text string, up to 55 characters long. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1440
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1441
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1442
NOTE: Use this attribute to specify a VRF name that is used to connect to the remote host. If no VRF is specified, then the default VRF is used. udp-port portnumber Enter the keywords udp-port then the UDP (User Datagram Protocol) port number on the remote device. The range is from 0 to 65535. The default is 162. 1 | 2c | 3 (OPTIONAL) Enter the security model version number (1, 2c, or 3): • 1 is the least secure version. • 3 is the most secure of the security modes.
PAGE 1443
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.6.(0.0) Added aes 128 encryption algorithm parameter. 9.4.(0.0) Added support for VRF. 9.
PAGE 1444
snmp-server user (for AES128-CFB Encryption) Specify that AES128-CFB encryption algorithm needs to be used for transmission of SNMP information. The Advanced Encryption Standard (AES) Cipher Feedback (CFB) 128-bit encryption algorithm is in compliance with RFC 3826. RFCs for SNMPv3 define two authentication hash algorithms, namely, HMAC-MD5-96 and HMAC-SHA1-96. These are the full forms or editions of the truncated versions, namely, HMAC-MD5 and HMAC-SHA1 authentication algorithms.
PAGE 1445
previously set up. Otherwise, you must remove the previously configured users before you change the FIPS mode. Example Dell# snmp-server user privuser v3group v3 encrypted auth md5 9fc53d9d908118b2804fe80e3ba8763d priv aes128 d0452401a8c3ce42804fe80e3ba8763d Related Commands show snmp user — Displays the information configured on each SNMP user name. snmp-server view Configure an SNMPv3 view.
PAGE 1446
Example Dell# conf Dell#(conf) snmp-server view rview 1.3.6.1 included Related Commands show running-config snmp — displays the SNMP running configuration. snmp-server vrf Configures an SNMP agent to bind to a specific VRF. Syntax snmp-server vrf vrf-name To undo the SNMP agent configuration, use the no snmp-server vrf vrf-name command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to associate an SNMP agent with that VRF. Defaults Not Enabled.
PAGE 1447
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1448
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands show logging — displays logging settings and system messages in the internal buffer. clear logging auditlog Clears audit log. Syntax clear logging auditlog Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1449
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands logging buffered — sets the logging buffered parameters.
PAGE 1450
default logging monitor Return to the default settings for messages logged to the terminal. Syntax default logging monitor Defaults level = 7 or debugging Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1451
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands logging trap — limit messages logged to the Syslog servers based on severity.
PAGE 1452
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Added udp and tcp keywords for the Z9500. 9.5(0.0) Added udp and tcp keywords for the S4810, S4820T, S6000, Z9000, and MXL. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.4.1.
PAGE 1453
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1454
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1455
Usage Information Version Description 9.5(0.0) Introduced on the S4810, S4820T, S6000, Z9000, and MXL. This command is available with or without RBAC enabled. When RBAC is enabled you can restrict access to audit and security logs based on the CLI sessions’ user roles. If extended logging is disabled, you can only view system events, regardless of RBAC user role. When you enabled RBAC and extended logging: • Only the system administrator role can execute this command.
PAGE 1456
• sys14 (system use) • syslog (Syslog process) • user (user process) • uucp (Unix to Unix copy process) The default is local7. Defaults local7 Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1457
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1458
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series.
PAGE 1459
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Related Commands default logging monitor — returns the logging monitor parameters to the default setting.
PAGE 1460
Related Commands logging — enables logging to the Syslog server. logging buffered — sets the logging buffered parameters. logging console — sets the logging console parameters. logging monitor — sets the logging parameters for the terminal connections. logging source-interface Specify that the IP address of an interface is the source IP address of Syslog packets sent to the Syslog server.
PAGE 1461
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Syslog messages contain the IP address of the interface used to egress the router.
PAGE 1462
Version Description 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information When you enable logging synchronous, unsolicited messages appear between software prompts and outputs. Only the messages with a severity at or below the set level are sent to the console.
PAGE 1463
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series, S55. 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information To block a type of message parameter, set the logging trap level to a lower number. For example, to block severity messages at level 6, set the level to 5. Related Commands logging — enables the logging to another device.
PAGE 1464
Example Dell(conf)#logging version ? <0-1> Select syslog version (default = 0) Dell(conf)#logging version 1 show logging Display the logging settings and system messages logged to the internal buffer of the switch. Syntax show logging [number | history [reverse][number] | reverse [number] | summary] Parameters Command Modes Command History number (OPTIONAL) Enter the number of messages displayed in the output. The range is from 1 to 65535.
PAGE 1465
Console logging: level debugging Monitor logging: level debugging Buffer logging: level debugging, 5604 Messages Logged, Size (524288 bytes) Trap logging: level informational Oct 8 09:25:37: %RPM1:RP1 %BGP-5-ADJCHANGE: Connection with neighbor 223.80.255.254 closed. Hold time expired Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.200.13.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.1.1.13 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 1.1.14.
PAGE 1466
Example Dell(conf)#show logging audit Related Commands clear logging auditlog — clears audit log. show logging driverlog stack-unit Display the driver log for the specified hardware component. Syntax show logging driverlog {cp | rp | linecard slot-id] Parameters defaults stack-unit stackunit-number Enter the keywords stack-unit followed by the stack member ID of the switch for which you want to display the driver log.
PAGE 1467
Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.
PAGE 1468
52 SNMP Traps This chapter lists the traps sent by the Dell Networking operating software. Each trap is listed by the fields Message ID, Trap Type, and Trap Option. Table 4. SNMP Trap List Message ID Trap Type Trap Option COLD_START SNMP COLDSTART WARM_START SNMP WARMSTART COPY_CONFIG_COMPLETE SNMP NONE SNMP LINKDOWN SNMP LINKUP SNMP AUTH EGP_NEIGHBOR_LOSS SNMP NONE OSTATE_DOWN SNMP LINKDOWN SNMP LINKUP SNMP NONE %SNMP-5-SNMP_COLD_START: SNMP COLD_START trap sent.
PAGE 1469
Message ID Trap Type Trap Option SNMP NONE SNMP NONE SNMP NONE SNMP NONE SNMP NONE SNMP NONE NONE NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE rising threshold alarm from SNMP OID RMON_FALLING_THRESHOLD %RPM0-P:CP %SNMP-4RMON_FALLING_THRESHOLD: RMON falling threshold alarm from SNMP OID RMON_HC_RISHING_THRESHOLD %RPM0-P:CP %SNMP-4RMON_HC_RISING_THRESHOLD: RMON high-capacity rising threshold alarm from SNMP OID RMON_HC_FALLING_THRESHOLD %RPM0-P:CP %SNMP-4RMO
PAGE 1470
Message ID Trap Type Trap Option CHM_ALARM_CUTOFF ENVMON NONE CHM_SFM_UP ENVMON NONE CHM_SFM_DOWN ENVMON NONE CHM_RPM_UP ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON SUPPLY %RAM-6-RPM_STATE: RPM1 is in Active State %RAM-6-RPM_STATE: RPM0 is in Standby State CHM_RPM_DOWN %CHMGR-2-RPM_DOWN: RPM 0 down - hard reset %CHMGR-2-RPM_DOWN: RPM 0 down - card removed CHM_RPM_PRIMARY %RAM-5-COLD_FAILOVER: RPM Failover
PAGE 1471
Message ID Trap Type Trap Option ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON SUPPLY ENVMON TEMP ENVMON TEMP ENVMON TEMP ENVMON TEMP ENVMON FAN %CHMGR-2-PEM_PRBLM: Major alarm: problem with power entry module %s CHM_PWRSRC_CLR %CHMGR-5-PEM_OK: Major alarm cleared: power entry module %s is good CHM_MAJ_ALARM_PS %CHMGR-0-MAJOR_PS: Major alarm: insufficient power %s CHM_MAJ_ALARM_PS_CLR %CHMGR-5-MAJOR_PS_CLR: major alarm cleared: sufficient power CHM_MIN_ALARM_PS %CHMGR
PAGE 1472
Message ID Trap Type Trap Option ENVMON FAN ENVMON FAN ENVMON FAN ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE %CHMGR-2-ALL_FAN_BAD: Major alarm: all fans in fan tray %d are down.
PAGE 1473
Message ID Trap Type Trap Option ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE ENVMON NONE PROTO NONE PROTO NONE PROTO NONE PROTO NONE %CHMGR-5-CPU_THRESHOLD_CLR: Cpu %s usage drops below threshold. Cpu5SecUsage (%d) CHM_MEM_THRESHOLD %CHMGR-5-MEM_THRESHOLD: Memory %s usage above threshold. MemUsage (%d) CHM_MEM_THRESHOLD_CLR %CHMGR-5-MEM_THRESHOLD_CLR: Memory %s usage drops below threshold.
PAGE 1474
Message ID Trap Type Trap Option BGP4_BACKW_XSITION PROTO NONE %TRAP-5-BACKWARD_STATE_TRANS: Neighbor %a, state %s 1474 SNMP Traps
PAGE 1475
53 Stacking All commands in this chapter are specific to the Dell Networking operating software. You can use the commands to pre-configure a switch, so that the configuration settings are invoked when the switch is attached to other S-Series units. For information about using the S-Series stacking feature, refer to the “Stacking S-Series Switches” chapter in the Dell Networking OS Configuration Guide. CAUTION: You cannot enable stacking simultaneously with virtual link trunking (VLT).
PAGE 1476
Version Description 8.3.1.0 Added the members option. Usage Information Enabling this command keeps the failed switch in the Failed state. The switch does not reboot until it is manually rebooted. When enabled, it is not displayed in the running-config. When disabled, it is displayed in the running-config. Related Commands show redundancy — displays the current redundancy status. redundancy force-failover stack-unit Force the standby unit in the stack to become the management unit.
PAGE 1477
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.
PAGE 1478
Usage Information Resetting the management unit is not allowed, and an error message displays if you try to do so. Resetting is a soft reboot, including flushing the forwarding tables. Starting with Dell Networking OS version 7.8.1.0, you can run this command directly on the stack standby unit (standby master) to reset the standby. You cannot reset any other unit from the standby unit.
PAGE 1479
Example • no-more — do not paginate the output. • save — save the output to a file.
PAGE 1480
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.
PAGE 1481
Interface Link Speed Admin Link (Gb/s) Status Status -------------------------------------------1/25/1 10 up up 1/26/1 10 up down 1/27/1 10 up down 1/28/1 10 up down 3/25/1 10 up up 3/26/1 10 up down 3/27/1 10 up down 3/28/1 10 up down Example (Topology) Related Commands Dell#show system stack-port topology Topology: Daisy chain Interface Connection --------------------1/25 3/25 1/26 1/27 1/28 3/25 1/25 3/26 3/27 3/28 • reset stack-unit – resets the designated stack member.
PAGE 1482
Related Commands Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.7.0 Introduced on the S4810. 8.3.11.1 Introduced on the Z9000. • reload – reboots Dell Networking OS. stack-unit provision Preconfigure a logical stacking ID of a switch that joins the stack. This is an optional command that is executed on the management unit.
PAGE 1483
stack-unit stack-group Configure the stacking unit and stacking group by specifying an ID when adding units to a stack to ensure the unit is assigned to the correct group. Syntax stack-unit unit-id stack-group stack-group-id To remove the current stack group configuration, use the no stack-unit unit-id stack-group stack-id command. Parameters unit-id Enter the stack unit ID. stack-group-id Enter the stack group ID.
PAGE 1484
system Enter the keyword system to copy the Dell Networking OS image from the management unit to the designated stack members. stack-unit Enter the stack-unit number. The range is from 1 to 6. all Enter the keyword all to copy the designated image to all stack members. A Enter the keyword A to upgrade all stacked units in System A ( only). B Enter the keyword B to upgrade all stacked units in System B ( only). Defaults none Command Modes EXEC Command History This guide is platform-specific.
PAGE 1485
54 Storm Control The Dell Networking operating software storm control feature allows you to limit or suppress traffic during a traffic storm (Broadcast/Unknown Unicast Rate Limiting or Multicast on the C-Series and S-Series). Storm control is supported on Dell Networking OS. Important Points to Remember • Interface commands can only be applied on physical interfaces (virtual local area networks [VLANs] and link aggregation group [LAG] interfaces are not supported).
PAGE 1486
Defaults • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/ port information. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1487
• Defaults Command Modes Command History For a port channel interface, enter the keywords port-channel then a number. none • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1488
Defaults • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a port channel interface, enter the keywords port-channel then a number. none Command Modes Command History • EXEC • EXEC Privilege This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1489
To disable broadcast rate-limiting, use the storm-control broadcast [percentage decimal_value in | out] | [wred-profile name]] [packets_per_second in] command. Parameters percentagedecimal _value in | out Enter the percentage of broadcast traffic allowed in or out of the network. Optionally, you can designate a decimal value percentage, for example, 55.5%. The decimal range is from .1 to .9. wred-profile name Enter the keyword wred-profile followed by the profile name to designate a wredprofile.
PAGE 1490
To disable broadcast storm control on the interface, use the no storm-control broadcast [packets_per_second in] command. Parameters packets_per_secon d in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368. Defaults none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1491
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.2(0.
PAGE 1492
Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the C-series and S-Series. storm-control PFC/LLFC Shut down the port if it receives the PFC/LLFC frames more than the configured rate.
PAGE 1493
Parameters packets_per_secon d in Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554368. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 1494
• 100% allows all traffic into the interface. The decimal range is from 0.1 to 0.9. wred-profile name E-Series Only: (Optionally) Enter the keywords wred-profile followed by the profile name to designate a wred-profile. packets_per_secon d in C-Series and S-Series Only: Enter the packets per second of broadcast traffic allowed into the network. The range is from 0 to 33554431. Defaults none Command Modes INTERFACE (conf-if-interface-slot/port) Command History This guide is platform-specific.
PAGE 1495
55 Spanning Tree Protocol (STP) The commands in this chapter configure and monitor the IEEE 802.1d spanning tree protocol (STP) and are supported on the Dell Networking switch/routing platform. bridge-priority Set the bridge priority of the switch in an IEEE 802.1D spanning tree. Syntax bridge-priority {priority-value | primary | secondary} To return to the default value, use the no bridge-priority command. Parameters priority-value Enter a number as the bridge priority value.
PAGE 1496
Version Description 6.2.1.1 Introduced on the E-Series. bpdu-destination-mac-address Use the Provider Bridge Group address in Spanning Tree or GVRP PDUs. Syntax bpdu-destination-mac-address [stp | gvrp] provider-bridge-group Parameters xstp Force STP, RSTP, and MSTP to use the Provider Bridge Group address as the destination MAC address in its BPDUs. gvrp Forces GVRP to use the Provider Bridge GVRP Address as the destination MAC address in its PDUs.
PAGE 1497
protocol Enter the keyword for the type of STP to debug, either mstp, pvst, or rstp. all (OPTIONAL) Enter the keyword all to debug all spanning tree operations. bpdu (OPTIONAL) Enter the keyword bpdu to debug bridge protocol data units. config (OPTIONAL) Enter the keyword config to debug configuration information. events (OPTIONAL) Enter the keyword events to debug STP events. general (OPTIONAL) Enter the keyword general to debug general STP operations.
PAGE 1498
Defaults none Command Modes SPANNING TREE (The prompt is “config-stp”.) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.
PAGE 1499
Related Commands Version Description 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. protocol spanning-tree — enters SPANNING TREE mode on the switch. forward-delay The amount of time the interface waits in the Listening state and the Learning state before transitioning to the Forwarding state.
PAGE 1500
hello-time — changes the time interval between BPDUs. hello-time Set the time interval between generation of the spanning tree bridge protocol data units (BPDUs). Syntax hello-time seconds To return to the default value, use the no hello-time command. Parameters seconds Enter a number as the time interval between transmission of BPDUs. The range is from 1 to 10. The default is 2 seconds. Defaults 2 seconds Command Modes SPANNING TREE Command History This guide is platform-specific.
PAGE 1501
max-age To maintain configuration information before refreshing that information, set the time interval for the spanning tree bridge. Syntax max-age seconds To return to the default values, use the no max-age command. Parameters seconds Enter a number of seconds the Dell Networking OS waits before refreshing configuration information. The range is from 6 to 40. The default is 20 seconds. Defaults 20 seconds Command Modes SPANNING TREE Command History This guide is platform-specific.
PAGE 1502
Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1503
Example Version Description 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.7.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series.
PAGE 1504
Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1505
Example Field Description “Port 1...” Displays the Interface type slot/port information and the status of the interface (Disabled or Enabled). “Port path...” Displays the path cost, priority, and identifier for the interface. “Designated root...” Displays the priority and MAC address of the root bridge of the STG that the interface belongs. “Designated port...” Displays the designated port ID.
PAGE 1506
Name PortID Prio Cost Sts Cost Bridge ID PortID -------------- ------ ---- ---- --- ----- -----------------Gi 1/1 8.26 8 4 FWD 0 32768 0001.e800.0a56 8.26 Gi 1/2 8.27 8 4 FWD 0 32768 0001.e800.0a56 8.27 Gi 1/3 8.28 8 4 FWD 0 32768 0001.e800.0a56 8.28 Dell# Usage Information Example (Guard) The following describes the show spanning-tree 0 guard command shown in the example. Field Description Interface Name STP interface. Instance STP 0 instance.
PAGE 1507
portfast [bpduguard [shutdown-on-viol ation]] Enter the keyword portfast to enable Portfast to move the interface into Forwarding mode immediately after the root fails. Enter the optional keyword bpduguard to disable the port when it receives a BPDU. Enter the optional keyword shutdown-on-violation to hardware disable an interface when a BPDU is received and the port is disabled. priority priority Enter keyword priority then a number as the priority. The range is from zero (0) to 15. The default is 8.
PAGE 1508
Root guard is supported on any STP-enabled port or port-channel except when used as a stacking port. When enabled on a port, root guard applies to all VLANs configured on the port. STP root guard and loop guard cannot be enabled at the same time on a port. For example, if you configure loop guard on a port on which root guard is already configured, the following error message is displayed: % Error: RootGuard is configured. Cannot configure LoopGuard.
PAGE 1509
56 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell Networking device. eula-consent Accept or reject the end user license agreement (EULA).
PAGE 1510
configuration information, user supplied contact information, names of data volumes, IP addresses, access control lists, diagnostics & performance information, network configuration information, host/server configuration & performance information and related data ("Collected Data") and transmits this information to Dell. By downloading SupportAssist and agreeing to be bound by these terms and the Dell end user license agreement, available at: www.dell.
PAGE 1511
Command History Usage Information Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. You are guided through a series of queries to configure SupportAssist. The generated commands are added to the running configuration, including the DNS resolve commands, if configured. This command starts the configuration wizard for the SupportAssist. At any time, you can exit by entering Ctrl-C. If necessary, you can skip some data entry.
PAGE 1512
Command History Usage Information Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. By default, each activity follows a set of default actions using a default schedule. Using this command, you can customize the set of actions and disable a certain activity. contact-company Configure the contact information for the company. Syntax contact-company name {company-name}[company-next-name] ...
PAGE 1513
Command Modes Command History Usage Information SUPPORTASSIST Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. Each contact person must be unique by their name. You can configure only one contact person. It is not possible to remove the first name or last name. The no form of the command removes the entire contact-person entry. This command is optional for SupportAssist service configuration.
PAGE 1514
Usage Information The server-name is used as a reference only and is not required to be used as part of a URL definition. There is a reserved name of default for the default server at stor.g3.ph.dell.com. You can customize the defaults for this server by entering the server default command and use the custom commands. You can configure one additional server. SupportAssist Activity Commands Dell Networking OS supports the following SupportAssist Activity mode commands.
PAGE 1515
Parameters default Enter the keyword default to revert back to the default set of actions for an activity. local-file-name Enter the name of the local action-manifest file. Allowable characters are: a to z, A to Z, 0 to 9, -, _, and space. Defaults default Command Modes SUPPORTASSIST ACTIVITY Command History Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1516
action-manifest show View the list of action-manifest for a specific activity. Syntax action-manifest show {all} Parameters Command Modes Command History Related Commands all Enter the keyword all to view the entire list of action-manifests that are available for an activity. SUPPORTASSIST ACTIVITY Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1517
To remove the complete company contact information, use the no address command. Parameters Command Modes Command History Usage Information city company-city (OPTIONAL) Enter the keyword city then the city or town for the company site. To include a space, enter a space within double quotes. province | region | state name (OPTIONAL) Enter the keyword province, region or state then the name of province, region or state for the company site. To include a space, enter a space within double quotes.
PAGE 1518
territory Configure the territory and set the coverage for the company site. Syntax territory company-territory To remove the company territory information, use the no territory command. Parameters Command Modes Command History Usage Information company-territory Enter the territory name for the company. To include a space, enter a space within double quotes. SUPPORTASSIST COMPANY Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1519
phone Configure phone numbers to reach the contact person. Syntax phone primary phone [alternate phone] To remove a phone number, use either the no phone primary or no phone alternate commands. Parameters Command Modes Command History Usage Information primary phone Enter the keyword primary then the primary phone number for the person. alternate phone Enter the keyword alternate then the alternate phone number for the person. SUPPORTASSIST PERSON Version Description 9.9(0.
PAGE 1520
To remove the time zone, use the no time-zone [zone | start-time | end-time] command. Parameters Command Modes Enter the keyword zone then a time difference from GMT expressed as HH:MM. This number may be preceded by either a + or – sign. start-time HH:MM Enter the keywords start-time then a starting time expressed as HH:MM. Use the 24-hour clock format. stop-time HH:MM Enter the keywords stop-time then a stopping time expressed as HH:MM. Use the 24-hour clock format.
PAGE 1521
Defaults encryption-type for the password is 0. Command Modes SUPPORTASSIST SERVER Command History Usage Information Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. The passwords are stored encrypted in the running configuration. enable Enable communication with the SupportAssist server. Syntax enable To disable communication to a specific SupportAssist server, use the no enable command.
PAGE 1522
show eula-consent Display the EULA for the feature. Syntax show eula-consent {support-assist | other feature} Parameters Command Modes Command History Example support-assist | other feature Enter the keywords support-assist or the text corresponding to other feature. EXEC Privilege Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL.
PAGE 1523
behalf of a company or other legal entity, you are further certifying to Dell that you have appropriate authority to provide this consent on behalf of that entity. If you do not consent to the collection, transmission and/or use of the Collected Data, you may not download, install or otherwise use SupportAssist. show running-config Display the current configuration and changes from the default values.
PAGE 1524
Command History Example Version Description 9.9(0.0) Introduced on the S4810, S4820T, S3048–ON, S4048–ON, S5000, S6000, S6000–ON, Z9500, MXL. Dell#show support-assist status SupportAssist Service: Installed EULA: Accepted Server: default Enabled: Yes URL: https://stor.g3.ph.dell.com Server: chennai Enabled: Yes URL: http://10.16.148.
PAGE 1525
57 System Time and Date The commands in this chapter configure time values on the system, either using the Dell Networking operating software, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host. For more information, refer to the “Network Time Protocol” section of the Management chapter in the Dell Networking OS Configuration Guide.
PAGE 1526
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.
PAGE 1527
start-day Enter the name of the day that you want daylight saving time to begin. Use English three letter abbreviations; for example, Sun, Sat, Mon, and so on. The range is from Sun to Sat. start-month Enter the name of one of the 12 months in English. start-time Enter the time in hours:minutes. For the hour variable, use the 24-hour format; example, 17:15 is 5:15 pm.
PAGE 1528
Related Commands Version Description 6.1.1.0 Introduced on the E-Series. clock summer-time date — sets a date (and time zone) on which to convert the switch to daylight saving time on a one-time basis. show clock — displays the current clock settings. clock timezone Configure a timezone for the switch. Syntax clock timezone timezone-name offset To delete a timezone configuration, use the no clock timezone command. Parameters timezone-name Enter the name of the timezone. You cannot use spaces.
PAGE 1529
Usage Information Coordinated universal time (UTC) is the time standard based on the International Atomic Time standard, commonly known as Greenwich Mean time. When determining system time, include the differentiator between UTC and your local timezone. For example, San Jose, CA is the Pacific Timezone with a UTC offset of -8. debug ntp Display network time protocol (NTP) transactions and protocol messages for troubleshooting.
PAGE 1530
Version Description 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series. ntp authenticate Enable authentication of NTP traffic between the switch and the NTP time serving hosts. Syntax ntp authenticate To disable NTP authentication, use the no ntp authentication command. Defaults Not enabled. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1531
Parameters number Specify a number for the authentication key. The range is from 1 to 4294967295. This number must be the same as the number parameter configured in the ntp trusted-key command. md5 Specify that the authentication key is encrypted using MD5 encryption algorithm. 0 Specify that authentication key is entered in an unencrypted format (default). 7 Specify that the authentication key is entered in DES encrypted format. key Enter the authentication key in the previously specified format.
PAGE 1532
ntp broadcast client Set up the interface to receive NTP broadcasts from an NTP server. Syntax ntp broadcast client To disable broadcast, use the no ntp broadcast client command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 1533
Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1534
Version Description 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.4.1.0 Added support for IPv6 multicast addresses. 8.3.7.0 Introduced on the S4810. 6.1.1.0 Introduced on the E-Series. ntp master Configure the switch as NTP Server. Syntax ntp master Parameters ntp master Enter the stratum number to identify the NTP Server's hierarchy. Defaults Not configured.
PAGE 1535
ipv4-address | ipv6address Enter an IPv4 address (A.B.C.D) or IPv6 address (X:X:X:X::X) of NTP server. hostname Enter the hostname of the server. key keyid (OPTIONAL) Enter the keyword key and a number as the NTP peer key. The range is from 1 to 4294967295. prefer (OPTIONAL) Enter the keyword prefer to indicate that this peer has priority over other servers. version number (OPTIONAL) Enter the keyword version and a number to correspond to the NTP version used on the server.
PAGE 1536
ntp source Specify an interface’s IP address to be included in the NTP packets. Syntax ntp source interface To delete the configuration, use the no ntp source command. Parameters interface Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
PAGE 1537
To delete the key, use the no ntp trusted-key number command. Parameters number Enter a number as the trusted key ID. The range is from 1 to 4294967295. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 1538
Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1539
Usage Information Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.0 Introduced on the E-Series.
PAGE 1540
* master (synced), # master (unsynced), + selected, - candidate Dell# Related Commands show ntp status — displays the current NTP status. show ntp vrf associations Displays the NTP servers configured for the VRF instance . Syntax show ntp [vrf] associations. Command Modes EXECEXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1541
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.1.1.
PAGE 1542
58 Tunneling Tunneling is supported on Dell Networking OS. ip unnumbered Configure a tunnel interface to operate without a unique IPv4 address and select the interface from which the tunnel borrows its address. Syntax ip unnumbered {interface-type slot/port} To set the tunnel back to default logical address use the no ip unnumbered command. If the tunnel was previously operational, the tunnel interface is operationally down unless you also configure the tunnel IPv6 address.
PAGE 1543
ipv6 unnumbered Configure a tunnel interface to operate without a unique IPv6 address and select the interface from which the tunnel borrows its address. Syntax ipv6 unnumbered {interface-type interface-number} To set the tunnel back to default logical address use the no ipv6 unnumbered command. If the tunnel was previously operational, the tunnel interface is operationally down unless you also configure the tunnel IPv4 address. Parameters interface-type interface-number Defaults None.
PAGE 1544
Parameters ip-address Enter the source IPv4 address in A.B.C.D format. ipv6–address Enter the source IPv6 address in X:X:X:X::X format. mask (OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D to match a range of remote addresses. The default mask is /32 for IPv4 addresses and /128 for IPv6 addresses, which match only the specified address. Defaults If you do not configure tunnel allow remote , all traffic which is destined to tunnel source address is decapsulated.
PAGE 1545
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S4810, S4820T, S6000 and Z9000. The tunnel interface is inoperable without a valid tunnel destination address for the configured Tunnel mode. To establish a logical tunnel to the particular destination address, use the destination address of the outer tunnel header.
PAGE 1546
A value of 0 copies original packet DSCP (IPv4)/Traffic Class (IPv6) to the tunnel header DSCP (IPv4)/ Traffic Class (IPv6) depending on the mode of tunnel. tunnel flow-label Configure the method to set the IPv6 flow label value in the outer tunnel header. Syntax tunnel flow-label value To return to the default value of 0, use the no tunnel flow-label value command. Parameters value Enter a value to set the IPv6 flow label value in the tunnel header. The range is from 0 to 1048575.
PAGE 1547
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.3(0.0) Introduced on the S6000, S4810, S4820T, Z9000. A value of 0 copies the inner packet hop limit (ipv6) or time-to-live (ipv4) in the encapsulated packet to the tunnel header hop limit (ipv6) or time-to-live (ipv4) value. tunnel keepalive Configure the tunnel keepalive target, interval and attempts.
PAGE 1548
Usage Information Enabling tunnel keepalive causes ICMP echo packets to be sent to the keepalive target. The ICMP echo will be sourced from the tunnel interface logical IPv4 or IPv6 address and will be tunnel encapsulated. The response will be accepted whether it returns tunnel encapsulated or not.
PAGE 1549
keepalive. Conversely, if you configure any tunnel allow-remote entries, the tunnel—mode command fails unless the decapsulate-any option is included. Configuration of IPv6 commands over decapsulate-any tunnel causes an error. tunnel source Set a source address for the tunnel. Syntax tunnel source {ip-address | ipv6–address | interface-type-number | anylocal} To delete the current tunnel source address, use the no tunnel source command. Parameters ip-address Enter the source IPv4 address in A.B.C.
PAGE 1550
59 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if you use this with NIC teaming, automatic recovery from a failed link. clear ufd-disable Re-enable one or more downstream interfaces on the switch/router that are in a UFD-Disabled Error state so that an interface can send and receive traffic.
PAGE 1551
Related Commands Version Description 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. • downstream — assigns a port or port-channel to the uplink-state group as a downstream interface. • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. debug uplink-state-group Enable debug messages for events related to a specified uplink-state group or all groups.
PAGE 1552
description Enter a text description of an uplink-state group. Syntax description text Parameters text Text description of the uplink-state group. The maximum length is 80 alphanumeric characters. Defaults none Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1553
example: gigabitethernet 1/1-2,5,9,11-12 port-channel 1-3,5. A comma is required to separate each port and port-range entry. Defaults none Command Modes UPLINK-STATE-GROUP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.
PAGE 1554
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1555
Usage Information Version Description 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. When one upstream interface in an uplink-state group goes down, you can configure the number of downstream interfaces in an uplink-state group are put into a link-down state with an UFD-Disabled error message.
PAGE 1556
Related Commands • uplink-state-group — creates an uplink-state group and enables the tracking of upstream links. show running-config uplink-state-group Display the current configuration of one or more uplink-state groups. Syntax show running-config uplink-state-group [group-id] Parameters Defaults group-id Displays the current configuration of all uplink-state groups or a specified group. The valid group-id values are from 1 to 16.
PAGE 1557
show uplink-state-group Display status information on a specified uplink-state group or all groups. Syntax Parameters Defaults Command Modes Command History show uplink-state-group [group-id] [detail] group-id Displays status information on a specified uplink-state group or all groups. The valid group-id values are from 1 to 16. detail Displays additional status information on the upstream and downstream interfaces in each group none • EXEC • EXEC Privilege This guide is platform-specific.
PAGE 1558
Downstream Interfaces : Te 5/2(Dis) Te 5/4(Dis) Te 5/11(Dis) Te 5/12(Dis) Te 5/13(Dis) Te 5/14(Dis) Te 5/15(Dis) Uplink State Group : 6 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 7 Status: Enabled, Up Upstream Interfaces : Downstream Interfaces : Uplink State Group : 16 Status: Disabled, Up Upstream Interfaces : Gi 1/25(Dwn) Po 8(Dwn) Downstream Interfaces : Gi 1/30(Dwn) Related Commands • show running-config uplink-state-group — displays the current configurati
PAGE 1559
An uplink-state group is considered operationally up if at least one upstream interface in the group is in the Link-Up state. An uplink-state group is considered operationally down if no upstream interfaces in the group are in the LinkUp state. No uplink-state tracking is performed when a group is disabled or in an operationally down state. To disable upstream-link tracking without deleting the uplink-state group, use the no enable command in uplink-state-group configuration mode.
PAGE 1560
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810. 8.4.2.3 Introduced on the S-Series S50. You can assign physical port or port-channel interfaces to an uplink-state group. You can assign an interface to only one uplink-state group.
PAGE 1561
60 VLAN Stacking With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one tunnel and switch them through the network transparently. The Dell Networking operating software supports this feature on Dell Networking OS. For more information about basic VLAN commands, refer to the Virtual LAN (VLAN) Commands section in the Layer 2 chapter.
PAGE 1562
• Red: Lowest priority packets that are always dropped (regardless of congestion status). Defaults Disabled; Packets with an unmapped DEI value are colored green. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.
PAGE 1563
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 8.3.1.0 Introduced on the C-Series and S-Series. Enable DEI before using this command. member Assign a stackable VLAN access or trunk port to a VLAN.
PAGE 1564
Version Description 8.3.11.1 Introduced on the Z9000. 8.2.1.0 Introduced on the E-Series ExaScale. 7.6.1.0 Introduced on the C-Series and S-Series. Usage Information Enable the stackable VLAN (using the vlan-stack compatible command) on the VLAN prior to adding a member to the VLAN. Related Commands vlan-stack compatible — enables stackable VLAN on a VLAN. stack-unit stack-group Configure a stacking group specified by an ID.
PAGE 1565
vlan-stack access Specify a Layer 2 port or port channel as an access port to the stackable VLAN network. Syntax vlan-stack access To remove access port designation, use the no vlan-stack access command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command.
PAGE 1566
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.
PAGE 1567
vlan-stack dot1p-mapping Map C-Tag dot1p values to an S-Tag dot1p value. Syntax Parameters vlan-stack dot1p-mapping c-tag-dot1p values sp-tag-dot1p value c-tag-dot1p value Enter the keyword c-tag-dot1p then the customer dot1p value that is mapped to a service provider do1p value. The range is from 0 to 7. sp-tag-dot1p value Enter the keyword sp-tag-dot1p then the service provider dot1p value. The range is from 0 to 7.
PAGE 1568
Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.
PAGE 1569
To remove a trunk port designation from the selected interface, use the no vlan-stack trunk command. Defaults Not configured. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.
PAGE 1570
vlan-stack trunk no shutdown Dell(conf-if-gi-1/42)#interface vlan 100 Dell(conf-if-vl-100)#vlan-stack compatible Dell(conf-if-vl-100-stack)#member gigabitethernet 1/42 Dell(conf-if-vl-100-stack)#show config ! interface Vlan 100 no ip address vlan-stack compatible member GigabitEthernet 1/42 shutdown Dell(conf-if-vl-100-stack)#interface vlan 20 Dell(conf-if-vl-20)#tagged gigabitethernet 1/42 Dell(conf-if-vl-20)#show config ! interface Vlan 20 no ip address tagged GigabitEthernet 1/42 shutdown Dell(conf-if-vl
PAGE 1571
61 Virtual Routing and Forwarding (VRF) Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist on the same router at the same time. ip vrf Create or delete a customer VRF. Syntax ip vrf {vrf-name | management} [vrf_id] To delete a customer VRF, use the no ip vrf {vrf-name | management} [vrf_id] command. Parameters vrf-name Enter the name of the VRF that you create. management Enter the keyword management to create the management VRF.
PAGE 1572
ip http vrf Configure an HTTP client with a VRF used to connect to the HTTP server. Syntax ip http vrf {management | vrf-name} To undo the HTTP client configuration, use the ip http vrf command. Parameters management Enter the keyword management for configuring the management VRF that uses an HTTP client. vrf-name Enter a VRF name that the HTTP client uses. If you do not specify a VRF name, the HTTP client uses the default VRF.
PAGE 1573
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series. ip vrf forwarding Attach an interface to a VRF.
PAGE 1574
You can configure an IP subnet or address on a physical or VLAN interface that overlaps the same IP subnet or address configured on another interface only if the interfaces are assigned to different VRFs. If you assign two interfaces to the same VRF, you cannot configure overlapping IP subnets or the same IP address to them.
PAGE 1575
The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To export all the routes corresponding to a source VRF, you can use the ip route-export tag command without specifying the route-map attribute.
PAGE 1576
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500.
PAGE 1577
Usage Information Version Description 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. To export all the routes corresponding to a source VRF, use the ip route-export tag command without specifying the route-map attribute. This action exposes source VRF routes to other VRFs, which then import these routes using the ip route-import tag command. In Dell Networking OS, you can configure one route-export per VRF as you can only expose one set of routes for leaking.
PAGE 1578
Usage Information Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S4810, S4820T, S5000, S6000, S6000–ON, and Z9500. It is possible to configure multiple import conditions per VRF depending on the exporting VRF. The export-target and import-target support only the match the protocol and prefix-list options. Other options that you configure in the route-maps are ignored. Related Commands ipv6 route-export — exports IPv6 routes to another VRF.
PAGE 1579
redistribute Redistributes leaked or exported routes corresponding to specific protocols. Syntax Parameters redistribute {imported-bgp | import-ospf | import-isis} imported-bgp Enter the keywords imported-bgp to redistribute leaked routes that are learned using the BGP protocol. imported-ospf Enter the keywords imported-ospf to redistribute leaked routes that are learned using the OSPF protocol.
PAGE 1580
Usage Information Version Description 9.5(0.0) Introduced on the Z9500. 9.4.(0.0) Introduced on the S-Series and Z9000. When you use this command, the management ports corresponding to both the active unit and the standby unit are associated with the management VRF. maximum dynamic-routes Specify the maximum number of dynamic (protocol) routes a VRF can have.
PAGE 1581
Usage Information If you do not specify the maximum route limit for a VRF, the VRF has unlimited space that extends to the maximum number of entries allowed for the system. This command does not apply to default and management VRFs. show ip vrf Displays information corresponding to the VRFs that you configure in the system.
PAGE 1582
test1 1 Gi 1/14,16-17 show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax show run vrf vrf-name Parameters Command Modes Command History vrf vrf-name • EXEC • EXEC Privilege Enter the keyword vrf and then the name of the VRF. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1583
62 VLT Proxy Gateway The Virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, refer to Dell Networking OS Command Line Reference Guide. proxy-gateway lldp Enables the proxy-gateway feature using the LLDP protocol.
PAGE 1584
proxy-gateway static Enables the proxy-gateway feature using static configurations. S3048–ON Syntax [no] proxy-gateway static Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.
PAGE 1585
Combination: 3, 4, 5-10, 8 Command Modes VLT DOMAIN PROXY GW STATIC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.4(0.
PAGE 1586
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.4(0.0) Introduced on the S4810, S4820T, S6000, and Z9000. Usage Information You must configure the VLT port channel interface which is connecting to the remote VLT domain as peerdomain-link.
PAGE 1587
Use this timer when you enable vlt-peer-mac transmit. A typical use example is a square VLT topology with a single link connecting to the remote peers. Example Dell(conf-vlt-domain-proxy-gw-lldp)# peer-timeout 5 vlt-peer-mac transmit Enables the device to transmit the peer MAC address along with its own MAC address in LLDP TLV packets to the remote VLT domain. S3048–ON Syntax [no] vlt-peer-mac transmit Command Modes VLT DOMAIN PROXY GW LLDP Command History This guide is platform-specific.
PAGE 1588
static Command Modes Command History • EXEC • EXEC Privilege Enter the keyword static to display details about the static VLT proxy gateway configuration. This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1589
63 Virtual Link Trunking (VLT) Virtual link trunking (VLT) allows physical links between two chassis to appear as a single virtual link to the network core. VLT eliminates the requirement for Spanning Tree protocols by allowing link aggregation group (LAG) terminations on two separate distribution or core switches, and by supporting a loop-free topology.
PAGE 1590
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1591
Version Description 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.2(0.2) Added multicast and ndp parameters. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Introduced on the S4810.
PAGE 1592
Usage Information Related Commands Version Description 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S8420T. 8.3.12.0 Introduced on the S4810. To delay the system from bringing up the VLT port for a brief period to allow IGMP snooping and Layer 3 routing protocols to converge, use the delay-restore command. Use this command: • after a VLT device reloads. • if the peer VLT device was up at the time the VLTi link failed.
PAGE 1593
lacp ungroup member-independent Prevent possible loop during the VLT peer switch bootup or on a device that accesses the VLT domain. Syntax Parameters lacp ungroup member-independent {vlt | port-channel} vlt Force all VLT LACP members to become switchports. port-channel Force all LACP port-channel members to become switchports. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is platform-specific.
PAGE 1594
multicast peer-routing timeout To retain synced multicast routes or synced multicast outgoing interface (OIF) after a VLT peer node failure, configure the timeout value for a VLT node. Syntax multicast peer-routing timeout value To restore the default value, use the no multicast peer-routing timeout command. Parameters value Enter the timeout value (in seconds). The range is from 1 to 1200. The default is 150.
PAGE 1595
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.12.0 Added support for the peer-down-vlan option. 8.3.8.0 Introduced on the S4810.
PAGE 1596
peer-routing-timeout Configure the delay after which peer routing disables when the peer is unavailable. This command is applicable for both IPv6 and IPv4. Syntax peer-routing-timeout value To restore the default value, use the no peer-routing-timeout command. Parameters value Enter the timeout value (in seconds). The range is from 1 to 65535. The default value is infinity. Command Modes VLT DOMAIN (conf-vlt-domain) Default Infinity Command History This guide is platform-specific.
PAGE 1597
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator.
PAGE 1598
Version Description 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810. Usage Information The version shown in the show vlt brief output command displays the VLT version number which is different from the Dell Networking OS version number. VLT version numbers begin with odd numbers.
PAGE 1599
Example Version Description 8.3.8.0 Introduced on the S4810. Dell_VLTpeer1# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.18 Up 1 3 34998 1026 1025 show vlt counters Displays counter information.
PAGE 1600
Version Description 8.3.12.0 Introduced on the S4810. Usage Information If you do not add a parameter such as arp or mac, the output displays all the counters.
PAGE 1601
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.
PAGE 1602
Multicast Route LocalIIF -----------------------(22.22.22.200, 225.1.1.2) VLAN 5 (*, 225.1.1.2) VLAN 15 Dell# PeerIIF --------VLAN 6 gi 1/5 show vlt mismatch Display mismatches in VLT parameters. Syntax show vlt mismatch Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. Version The following is a list of the Dell Networking OS version history for this command.
PAGE 1603
Example for Q-in-Q Dell#show vlt implementation over Domain -----VLT Parameters ---------PB for stp mismatch Local ----Enabled Peer ---Disabled Vlan-type-config ---------------Codes:: P - Primary, C - Community, I - Isolated, N - Normal vlan, M Vlan-stack Vlan-ID ------- Local ----- 100 Peer ---- N M Port-type-config ---------------Codes:: p - PVLAN Promiscuous port, h - PVLAN Host port, t - PVLAN Trunk port, mt - Vlan-stack trunk port, mu - Vlan-stack access port, n Normal port Vlt Lag ------128
PAGE 1604
Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.0 Introduced on the S4810.
PAGE 1605
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Related Commands Example Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.2) Added parameters multicast and ndp 9.0.2.
PAGE 1606
Info Pkts Sent: 4 Info Pkts Rcvd: 2 Reg Request Sent: 2 Reg Request Rcvd: 2 Reg Response Sent: 1 Reg Response Rcvd: 0 Route updates sent to Peer: 0 Route updates rcvd from Peer: 0 Route update pkts sent to Peer: 0 Route update pkts rcvd from Peer: 0 VLT NDP Statistics -------------------NDP NA VLT Tunnel Pkts sent:16 NDP NA VLT Tunnel Pkts Rcvd:46 NDP NA Non-VLT Tunnel Pkts sent:0 NDP NA Non-VLT Tunnel Pkts Rcvd:0 Ndp-sync Pkts Sent:144 Ndp-sync Pkts Rcvd:105 Ndp Reg Request sent:25 Ndp Reg Request rcvd:24
PAGE 1607
IGMP PDU Tunnel Pkt rcvd:10 IGMP Tunnel PDUs sent: 10 IGMP Tunnel PDUs rcvd: 19 system-mac Reconfigure the default MAC address for the domain. Syntax Parameters system-mac mac-address mac-address Enter the system MAC address for the VLT domain. Defaults Not configured. Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1608
Parameters 0|1 Configure the default unit ID of a VLT peer switch. Enter 0 for the first peer. Enter 1 for the second peer. Defaults Automatically assigned based on the MAC address of each VLT peer. The peer with the lower MAC address is assigned unit 0; the peer with the higher MAC address is assigned unit 1. Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1609
The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.5(0.1) Introduced on the Z9500. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.0 Introduced on the S4820T. 8.3.8.
PAGE 1610
Version Description 8.3.8.0 Introduced on the S4810. 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in ProgrammableMux (PMUX) mode only. show vlt private-vlan Display the private VLAN (PVLAN) associated with the VLT LAG for VLT peer nodes. Syntax show vlt private-vlan Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1611
64 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell Networking operating system on Dell Networking OS. IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. Syntax advertise-interval {seconds | centisecs centisecs } To return to the default settings, use the no advertise-interval command. Parameters seconds Enter the number of seconds. The range is from 1 to 255.
PAGE 1612
Usage Information Version Description 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Dell Networking recommends keeping the default setting for this command. If you do change the time interval between VRRP advertisements on one router, change it on all routers. authentication-type Enable authentication of VRRP data exchanges. Syntax authentication-type simple [encryption-type] password To delete an authentication type and password, use the no authentication-type command.
PAGE 1613
Usage Information The system encrypts the password and the show config command displays the encrypted text string. clear counters vrrp Clear the counters maintained on VRRP operations. Syntax Parameters clear counters vrrp [vrrp-id] [ipv6] vrrp-id (OPTIONAL) Enter the number of the VRRP group ID to clear the group’s counters. The range is from 1 to 255. ipv6 (OPTIONAL) Enter the keyword ipv6 to clear counters from the IPv6 VRRP group.
PAGE 1614
Usage Information NOTE: This command also enables you to clear the port configurations corresponding to a range of ports. However, for Open Networking (ON) platforms the notation for specifying port range in the command is different from how you specify in non-ON platforms. • For non-ON platforms, you can specify multiple ports as slot/port-range.
PAGE 1615
Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. If you do not specify an option, debug is active on all interfaces and all VRRP groups.
PAGE 1616
Version Description 6.2.1.1 Introduced on the E-Series. disable Disable a VRRP group. Syntax disable To re-enable a disabled VRRP group, use the no disable command. Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1617
centisecs centisecs Enter the keyword centisecs then the number of centisecs in units of 25 centisecs. The range is from 0 to 65525 in units of 25 centisecs. Defaults zero (0) seconds or (0) centiseconds Command Modes VRRP Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version Description 9.8(0.
PAGE 1618
Version Description 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 9.0.2.0 Introduced on the S6000. 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. priority Specify a VRRP priority value for the VRRP group.
PAGE 1619
Usage Information Version Description 6.2.1.1 Introduced on the E-Series. To guarantee that a VRRP group becomes MASTER, configure the VRRP group’s virtual address with same IP address as the interface’s primary IP address and change the priority of the VRRP group to 255. If you set the priority command to 255 and the virtual-address is not equal to the interface’s primary IP address, an error message appears. show config View the nondefault VRRP configuration.
PAGE 1620
show vrrp View the VRRP groups that are active. If no VRRP groups are active, the Dell Networking OS returns No Active VRRP group. Syntax show vrrp [vrrp-id][brief][interface type][ipv6][interface type][vrf vrfname] Parameters Command Modes Command History vrrp-id (OPTIONAL) Enter the virtual router identifier for the VRRP group to view only that group. The range is from 1 to 255. brief (OPTIONAL) Enter the keyword brief to view a table of information about the VRRP groups.
PAGE 1621
Usage Information Version Description 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. The following describes the show vrrp brief command shown in the following example. Item Description Interface Lists the interface type, slot, and port of the configured VRRP group. Grp Displays the VRRP group ID. Pri Displays the priority value assigned to the interface.
PAGE 1622
Item Description Hold Down:... Displays additional VRRP configuration information: Adv rcvd:... Example 1622 • Hold Down displays the hold down timer interval in seconds. • Preempt displays TRUE if preempt is configured and FALSE if preempt is not configured. • AdvInt displays the Advertise Interval in seconds. Displays counters for the following: • Adv rcvd displays the number of VRRP advertisements received on the interface.
PAGE 1623
Example (VRRP VRF) track Monitor an interface and lower the priority value of the VRRP group on that interface if it is disabled. Syntax track interface [priority-cost cost] To disable monitoring, use the no track interface command. Parameters interface priority-cost (OPTIONAL) Enter the following keywords and slot/port or number information: • For a 1-Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
PAGE 1624
virtual-address Configure up to 12 virtual router IP addresses in the VRRP group. To start sending VRRP packets, set at least one virtual IP address for the VRRP group. Syntax virtual-address ip-address1 [... ip-address12] To delete one or more virtual IP addresses, use the no virtual-address ip-address1 [... ipaddress12] command. Parameters ip-address1 Enter an IP address of the virtual router in dotted decimal format. The IP address must be on the same subnet as the interface’s primary IP address. ..
PAGE 1625
vrrp delay minimum Set the delay time for VRRP initialization after an interface comes up. Syntax Parameters vrrp delay minimum seconds seconds Enter the number of seconds for the delay for VRRP initialization after an interface becomes operational. The range is from 0 to 900 (0 indicates no delay). Defaults 0 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide.
PAGE 1626
Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.0.2.0 Introduced on the S6000. 9.0.0.0 Introduced on the Z9000. 8.3.19.
PAGE 1627
Version Description 8.3.19.0 Introduced on the S4820T. 8.3.11.1 Introduced on the Z9000. 8.3.7.0 Introduced on the S4810. 7.6.1.0 Introduced on the S-Series. 7.5.1.0 Introduced on the C-Series. 6.2.1.1 Introduced on the E-Series. Usage Information The VRRP group only becomes active and sends VRRP packets when you configure a virtual IP address. When you delete the virtual IP address, the VRRP group stops sending VRRP packets.
PAGE 1628
2. Set the switch with the highest priority to version 3. 3. Set all the switches from both to version 3. NOTE: Do not run VRRP version 2 and version 3 in the same group for an extended period of time. Example Dell(conf-if-gi-1/1-vrid-100)#version ? 2 VRRPv2 3 VRRPv3 both Interoperable, send VRRPv3 receive both Dell(conf-if-gi-1/1-vrid-100)#version 3 IPv6 VRRP Commands The following are IPv6 VRRP commands.
PAGE 1629
Version Description 9.9(0.0) Added support to clear the interface configurations corresponding to a range of ports. 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.7(0.0) Introduced on the S6000-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.4.1.0 Introduced on E-Series ExaScale, C-Series, and S-Series. Support was added for IPv6 VRRP groups in nondefault VRF instances. 8.3.2.
PAGE 1630
state Enter the keyword state to enable debugging of VRRP state changes timer Enter the keyword timer to enable debugging of the VRRP timer. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.
PAGE 1631
• Command History EXEC Privilege This guide is platform-specific. For command information about other platforms, see the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Usage Information Version Description 9.8(0.0P5) Introduced on the S4048-ON. 9.8(0.0P2) Introduced on the S3048-ON. 9.2(1.0) Introduced on the Z9500. 8.3.19.0 Introduced on the S4820T. 8.3.10.0 Introduced on the S4810. 8.3.2.
PAGE 1632
Example Line starting with Description Tracking states... Displays information on the tracked interfaces or objects configured for a VRRP group (track command), including: • UP or DOWN state of the tracked interface or object (Up or Dn). • Interface type and slot/port or object number, description, and time since the last change in the state of the tracked object. • Cost subtracted from the VRRP group priority if the state of the tracked interface/object goes DOWN.
PAGE 1633
Usage Information Version Description 8.3.2.0 Introduced on the E-Series TeraScale. The VRRP group only becomes active and sends VRRP packets when you configure a link-local virtual IP address. When you delete the virtual address, the VRRP group stops sending VRRP packets. • When you do not load the VRF microcode in the CAM, the VRID for a VRRP group is the same as the VRID number configured with the vrrp-group or vrrp-ipv6-group commands.