Dell Networking N1108T-ON/N1108P-ON/ N1108EP-ON/N1124T-ON/ N1124P-ON/N1148T-ON/ N1148P-ON Switches Getting Started Guide Guide de mise en route Guia de Noções Básicas Guía de introducción Regulatory Model: E17W and E18W Regulatory Type: E17W001/E18W001/E18W002
Dell Networking N1108T-ON/N1108P-ON/ N1108EP-ON/N1124T-ON/ N1124P-ON/N1148T-ON/ N1148P-ON Switches Getting Started Guide Regulatory Models: E17W and E18W
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your switch. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Lithium battery caution: • There is a danger of explosion if a battery is incorrectly replaced. Replace only with the same or equivalent type.
Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . N1100-ON Series Hardware Overview . . . . . . . . . . Power Consumption for N1100-ON Series PoE Switches . . . . . . . . . . . . . . . . Ventilation System . . . . . 5 6 . . . . . . . . . . . . N1108T-ON/N1108P-ON/N1108EP-ON Installation . . . . . . . . . . . . . . . . . . . . . . . . 7 8 Mounting an N1108T-ON/N1108P-ON Switch Using Dell Tandem Tray . . . . . . . . . . . . . . . . . . . . .
4 Starting and Configuring the N1100-ON Series Switch . . . . . . . . . . . . . Connecting an N1100-ON Series Switch to a Terminal . . . . . . . . . . . . . . . . . . . . . . . . 16 Connecting an N1100-ON Series Switch to a Power Source . . . . . . . . . . . . . . . . . . . . . 17 . . . . . . . . . . . 17 AC and DC Power Connection . . . . . . . . . 18 . . . . . . . . . . . . 19 Booting the N1100-ON Series Switch . Performing the N1100-ON Series Initial Configuration . . . . . . .
Introduction This document provides basic information about the Dell Networking N1100-ON Series switches, including how to install a switch and perform the initial configuration. For information about how to configure and monitor switch features, refer to the User Configuration Guide, which is available on the Dell Support website at dell.com/support. See the Support website for the latest updates on documentation and firmware.
Model Input Voltage Power Supply Configuration Maximum Maximum Steady Current Steady Consumption (A) Power (W) N1108EP-ON 100V/60Hz 54VDC External power adaptor 1.62A 157W 110V/60Hz 54VDC External power adaptor 1.47A 157W 120V/60Hz 54VDC External power adaptor 1.35A 157W 220V/50Hz 54VDC External power adaptor 0.74A 157W 240V/50Hz 54VDC External power adaptor 0.67A 157W 100V/60Hz Main PSU 2.66A 260.66W 110V/60Hz Main PSU 2.38A 257.95W 120V/60Hz Main PSU 2.16A 256.
N1100-ON Series Model Summary Table 1-2.
N1108T-ON/N1108P-ON/N1108EP-ON Installation Mounting an N1108T-ON/N1108P-ON Switch Using Dell Tandem Tray The AC power connector is on the rear panel. WARNING: Read the safety information in the Safety and Regulatory Information as well as the safety information for other switches that connect to or support the switch. WARNING: Do not use rack mounting kits to suspend the switch from under a table or desk, or attach it to a wall. CAUTION: Disconnect all cables from the switch before continuing.
3 Secure the kit to the rack with either the rack bolts or cage nuts and cagenut bolts with washers (depending on the kind of rack you have). Fasten the bolts on the bottom before fastening the bolts on the top. Mounting an N1108T-ON/N1108P-ON/N1108EP-ON on a Two-Post Rack Using Large L-brackets NOTE: The AC power connector is on the rear panel of the N1108T-ON/N1108P-ON switches. The DC power connector for the N1108EP-ON is at the center of the rear panel.
4 Insert the switch and rail assembly into the rack from the front of the rack. Make sure that the rack-mounting holes on the switch line up to the mounting holes on the rack. 5 Secure the switch to the rack with the rack screws. Fasten the lower pair of screws before the upper pair of screws. See Figure 1-3. Figure 1-3.
Figure 1-4. Inserting Mounting Brackets 4 Repeat the process for the wall-mounting bracket on the other side of the switch. 5 Place the switch on the wall in the location where the switch is being installed. 6 Mark the locations on the wall where the screws to hold the switch must be prepared. 7 On the marked locations, drill the holes and place all the eight supplied anchors in the holes. 8 Insert the supplied screws into the wall-mounting bracket holes and tighten them with a screwdriver. See Figure 1-5.
Figure 1-5.
N1124T-ON/N1124P-ON/N1148T-ON/ N1148P-ON Installation Rack Mounting an N1124T-ON/N1124P-ON/ N1148T-ON/ N1148P-ON Switch WARNING: Read the safety information in the Safety and Regulatory Information as well as the safety information for other switches that connect to or support the switch. The AC power connector is on the rear panel of the switch. Installing in a Rack WARNING: Do not use rack mounting kits to suspend the switch from under a table or desk, or attach it to a wall.
2 Insert the supplied bolts into the rack-mounting holes and tighten with a screwdriver. 3 Repeat the process for the rack-mounting bracket on the other side of the switch. 4 Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rackmounting holes on the bracket line up with the mounting holes in the rack. 5 Secure the bracket to the rack with either the rack bolts or cage nuts and cage-nut bolts with washers (depending on the kind of rack you have).
Starting and Configuring the N1100-ON Series Switch The following flow chart provides an overview of the steps you use to perform the initial configuration after the switch is unpacked and mounted. Figure 1-7.
Connecting an N1100-ON Series Switch to a Terminal After completing all external connections, configure the switch by connecting it to a terminal. NOTE: Read the Release Notes for this product before proceeding. You can download the Release Notes from the Dell Support website at dell.com/support. NOTE: Dell recommends that you obtain the most recent version of the user documentation from the Dell Support website at dell.com/support.
NOTE: Console access to the stack manager is available from any console port via the local CLI. Only one USB console session at a time is supported. Connecting an N1100-ON Series Switch to a Power Source CAUTION: Read the safety information in the Safety and Regulatory Information manual as well as the safety information for other switches that connect to or support the switch. The N1108T-ON and N1108P-ON models have one internal power supply. The power receptacle is on the rear panel.
Booting the N1100-ON Series Switch When the power is turned on with the local terminal already connected, the switch goes through a power-on self-test (POST). POST runs every time the switch is initialized and checks hardware components to determine if the switch is fully operational before completely booting. If POST detects a critical problem, the program flow stops. If POST passes successfully, valid firmware is loaded into RAM.
Performing the N1100-ON Series Initial Configuration The initial configuration procedure is based on the following assumptions: • The Dell Networking switch was never configured before. • The Dell Networking switch booted successfully. • The console connection was established, and the Dell Easy Setup Wizard prompt appears on the screen of a PC running terminal emulation software. The initial switch configuration is performed through the console port.
Initial Configuration Procedure Perform the initial configuration by using the Dell Easy Setup Wizard or by using the CLI. The wizard automatically starts when the switch configuration file is empty. Exit the wizard at any point by entering [ctrl+z], but all configuration settings specified will be discarded, and the switch will use the default values. NOTE: If you do not run the Dell Easy Setup Wizard or do not respond to the initial Easy Setup Wizard prompt within 60 seconds, the switch enters CLI mode.
Example Session This section describes a Dell Easy Setup Wizard session. The following values are used by the example session: • The SNMP community string to be used is public. • The network management system (NMS) IP address is 10.1.2.100. • The user name is admin, and the password is admin123. • The IP address for the VLAN 1 routing interface is 10.1.1.200 with a subnet mask of 255.255.255.0. • The default gateway is 10.1.1.1. The setup wizard configures the initial values as defined above.
Dell Easy Setup Wizard Console Example The following example contains the sequence of prompts and responses associated with running an example Dell Easy Setup Wizard session, using the input values listed earlier. After the switch completes the POST and is booted, the following dialog appears: Unit 1 - Waiting to select management unit)> ___________Dell SupportAssist EULA__________________ I accept the terms of the license agreement.
receive related repair services from Dell. You further agree to allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dell's affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
with normal operation using the default system configuration. Note: You can exit the setup wizard at any point by entering [ctrl+z]. Would you like to run the setup wizard (you must answer this question within 60 seconds)? [Y/N] y Step 1: The system is not set up for SNMP management by default. To manage the switch using SNMP (required for Dell Network Manager) you can . Set up the initial SNMP version 2 account now. . Return later and set up other SNMP accounts.
Step 2: Now we need to set up your initial privilege (Level 15) user account. This account is used to login to the CLI and Web interface. You may set up other accounts and change privilege levels later. For more information on setting up user accounts and changing privilege levels, see the user documentation. To set up a user account: Please enter the user name.
Finally, set up the default gateway. Please enter the IP address of the gateway from which this network is reachable. [0.0.0.0]: 10.1.1.1 This is the configuration information that has been collected: SNMP Interface = “public”@10.1.2.100 User Account setup = admin Password = ******** VLAN1 Router Interface IP = 10.1.1.200 255.255.255.0 Default Gateway = 10.1.1.1 Step 6: If the information is correct, please enter (Y) to save the configuration and copy the settings to the start-up configuration file.
The N1100-ON Series switches support basic switching features such as VLANs and spanning tree protocol. Use the Web-based management interface or the CLI to configure the features your network requires. For information about how to configure the switch features, refer to the User Configuration Guide or CLI Reference Guide available on the support site: dell.com/support.
Agency compliance The N1108T-ON, N1108P-ON, N1108EP-ON, N1124T-ON, N1124P-ON, N1148T-ON, and N1148P-ON switches comply with the following safety and agency requirements: USA Federal Communications Commission statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designated to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Figure 1-8. Canadian department of communication statement Safety standards and compliance agency certifications • IEC 62368-1, 2nd Edition • CUS UL 60950-1, 2nd Edition • Meets or exceeds Hi Pot and Ground Continuity testing per UL 60950-1.
• Europe: EN55032:2015 (CISPR 32), Class A • EN55032 • Japan: VCCI Class A • Korea: KN32, Class A • Taiwan: CNS13438, Class A • USA: FCC CFR47 Part 15, Subpart B, Class A Immunity • EN 300 386 EMC for Network Equipment • EN 55024 • EN 61000-3-2 Harmonic Current Emissions • EN 61000-3-3 Voltage Fluctuations and Flicker • EN 61000-4-2 ESD • EN 61000-4-3 Radiated Immunity • EN 61000-4-4 EFT • EN 61000-4-5 Surge • EN 61000-4-6 Low Frequency Conducted Immunity Product recycling and
NOM Information (Mexico Only) The following information is provided on the device(s) described in this document in compliance with the requirements of the official Mexican standards (NOM): Exporter: Dell Inc. One Dell Way Round Rock, TX 78682 Importer: Dell México, S.A. de C.V Av. Javier Barros Sierra, no 540, Piso 10, Col. Lomas de Santa Fe Delegación Álvaro Obregón, Ciudad de México. C.P. 01219 R.F.C: DME9204099R6 Ship to: Dell México, S.A. de C.V Av. Javier Barros Sierra, no 540, Piso 10, Col.
32 Getting Started Guide
Dell Networking N1108T-ON/N1108P-ON/ N1108EP-ON/N1124T-ON/ N1124P-ON/N1148T-ON/ N1148P-ON Guide de mise en route Modèles réglementaires : E17W et E18W
Remarques, précautions et avertissements REMARQUE: REMARQUE signale des informations importantes qui vous aident à mieux utiliser votre commutateur. PRÉCAUTION: Une PRÉCAUTION indique un risque d’endommagement du matériel ou de perte de données et vous indique comment éviter le problème. AVERTISSEMENT: Un AVERTISSEMENT indique un risque d’endommagement du matériel, de blessures corporelles ou même de mort.
Table des matières 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . Présentation du matériel Série N1100-ON . . . . . . . Consommation électrique des commutateurs PoE Série N1100-ON . . . . . . . . . . . . . Système de ventilation 37 . . . . . . . . . . . . . . . 39 . . . . . . . . . . Installation des commutateurs N1108T-ON/N1108P-ON/N1108EP-ON . . . 39 40 Montage d’un commutateur N1108T-ON/N1108P-ON à l’aide d’un plateau tandem Dell . . . . . . . . . . . .
4 Démarrage et configuration des commutateurs Série N1100-ON . . . . . . . . Connexion d’un commutateur Série N1100-ON à un terminal . . . . . . . . . . . . . . . . . . . . . . . 48 Série N1100-ONConnexion d’un commutateur à une source d’alimentation . . . . . . . . . . . . . . . 49 . . . . . . . . 49 Connexion du câble d’alimentation secteur et CC . . . . . . . . . . . . Démarrage du commutateur Série N1100-ON . . . . . . Réalisation de la configuration initiale du Série N1100-ON . . . . . .
Introduction Ce document fournit des informations de base concernant les commutateurs Dell Networking Série N1100-ON, y compris leur installation et leur configuration initiale. Pour en savoir plus sur la façon de configurer et surveiller les fonctions du commutateur, reportez-vous au User Configuration Guide (Guide de configuration utilisateur), qui est disponible sur le site Web du support de Dell dell.com/support.
Tableau1-1.
Système de ventilation Un seul ventilateur refroidit les commutateurs N1108T-ON/N1108P-ON et deux ventilateurs refroidissent les commutateurs N1024T-ON/N1024P-ON/ N1048T-ON/N1048P-ON. Les ventilateurs ne sont pas remplaçables sur le terrain. Le commutateur N1108EP-ON n’est pas équipé d’un ventilateur. Résumé du modèle Série N1100-ON Tableau1-2.
Installation des commutateurs N1108T-ON/N1108P-ON/N1108EP-ON Montage d’un commutateur N1108T-ON/N1108P-ON à l’aide d’un plateau tandem Dell Le connecteur d’alimentation CA se trouve sur le panneau arrière.
2 Insérez le commutateur dans le rack de 48,26 cm (19 pouces) en veillant à ce que les orifices de montage en rack situés sur le kit s’alignent bien sur ceux du rack. 3 Fixez le kit sur le rack en utilisant les boulons de rack ou les écrous à cage et les écrous à cage avec rondelles (selon le type du rack). Fixez d’abord les boulons sur le bas avant de fixer ceux du haut.
2 Insérez les vis fournies dans les orifices de montage en rack et serrez-les à l’aide d’un tournevis. 3 Répétez l’opération de l’autre côté du commutateur. 4 Insérez l’assemblage du commutateur et du rail dans le rack depuis l’avant du rack. Assurez-vous de bien aligner les orifices de montage en rack du commutateur avec ceux du rack. 5 Fixez le commutateur au rack à l’aide des vis du rack. Fixez les vis du bas avant les vis du haut. Voir la Figure 1-3. Figure 1-3.
2 Placez le support de montage mural fourni sur un côté du commutateur, en alignant bien les orifices de montage du commutateur avec ceux situés sur le support de montage mural. 3 Insérez les vis fournies dans les orifices du support de montage mural et serrez-les avec un tournevis. Voir la Figure 1-4. Figure 1-4. Insertion des supports de montage 4 Répétez le processus pour le support de montage mural situé de l’autre côté du commutateur.
7 Percez les trous sur les emplacements que vous avez marqués et insérez les huit chevilles fournies dans les trous. 8 Insérez les vis fournies dans les orifices des supports de montage mural et serrez-les avec un tournevis. Voir la Figure 1-5. Figure 1-5.
Installation des N1124T-ON/N1124PON/N1148T-ON/ N1148P-ON Montage en rack d’un commutateur N1124T-ON/ N1124P-ON/ N1148T-ON/ N1148P-ON AVERTISSEMENT: Prenez connaissance des consignes de sécurité exposées dans le manuel Safety and Regulatory Information (Informations relatives à la réglementation et la sécurité) ainsi que des informations relatives à la sécurité des autres commutateurs qui se connectent au commutateur ou qui le prennent en charge.
2 Insérez les boulons fournis dans les orifices de montage en rack et serrez-les à l’aide d’un tournevis. 3 Répétez le processus pour le support de montage situé sur l’autre côté du commutateur. 4 Insérez le commutateur dans le rack de 48,26 cm (19 pouces) en faisant en sorte que les orifices de montage en rack situés sur le support s’alignent sur ceux du rack. 5 Fixez le support sur le rack en utilisant les boulons de rack ou les écrous à cage et les écrous à cage avec rondelles (selon le type du rack).
Démarrage et configuration des commutateurs Série N1100-ON Le diagramme qui suit donne une vue générale de la procédure à suivre pour effectuer la configuration initiale une fois que le commutateur a été déballé et monté. Figure 1-7.
Connexion d’un commutateur Série N1100-ON à un terminal Après avoir effectué toutes les connexions externes, configurez le commutateur en le connectant à un terminal. REMARQUE: Avant de continuer, lisez les notes de mise à jour concernant ce produit. Vous pouvez télécharger les notes de mise à jour à partir du site web du support de Dell dell.com/ support. REMARQUE: Dell vous recommande de vous procurer la version la plus récente de la documentation utilisateur, disponible sur le site dell.com/support.
f Choisissez l’option Touches de terminal pour les touches de fonction, de direction et Ctrl. Assurez-vous que le paramètre correspond bien aux touches de terminal (et non aux touches Microsoft Windows). 3 Branchez le connecteur USB de type B du câble directement sur le port de console du commutateur. Le port de console du Dell Networking est situé sur le côté droit du panneau avant et est identifiable par le symbole |O|O|.
Démarrage du commutateur Série N1100-ON Lorsque le système est mis sous tension alors que le terminal local est déjà connecté, le commutateur effectue un POST (auto-test de démarrage). Ce test s’exécute chaque fois que le commutateur est initialisé et il vérifie les composants afin de déterminer si le commutateur est entièrement opérationnel avant de démarrer complètement. Si le test détecte un problème critique, le processus s’arrête.
Réalisation de la configuration initiale du Série N1100-ON La procédure de configuration initiale présuppose les éléments suivants : • Le commutateur Dell Networking n’a jamais été configuré auparavant. • Le commutateur Dell Networking a bien démarré. • La connexion à la console a été établie et l’invite de l’Assistant Dell d’installation facile est affichée sur l’écran d’un PC exécutant un logiciel d’émulation de terminal. La configuration initiale du commutateur est effectuée via le port de console.
Procédure de configuration initiale Effectuez la configuration initiale à l’aide de l’ Assistant Dell d’installation facile ou en utilisant la CLI. L’Assistant démarre automatiquement si le fichier de configuration du commutateur est vide. Vous pouvez quitter l’Assistant à tout moment en entrant [Ctrl+Z], mais tous les paramètres configurés seront ignorés et le commutateur utilisera les valeurs par défaut.
Exemple de session Cette section décrit une session Assistant Dell d’installation facile. Les valeurs suivantes sont utilisées dans la session : • La chaîne de communauté SNMP à utiliser est public. • L’adresse IP du système de gestion du réseau (NMS) est 10.1.2.100. • Le nom d’utilisateur est admin et le mot de passe admin123. • L’adresse IP de l’interface de routage VLAN 1 est 10.1.1.200 avec un masque de sous-réseau 255.255.255.0. • La passerelle par défaut est 10.1.1.1.
Exemple de la console Assistant Dell d’installation facile L’exemple suivant contient la séquence d’invites et de réponses d’un exemple de session Assistant Dell d’installation facile avec les valeurs indiquées plus haut. Au démarrage du commutateur après le POST, la boîte de dialogue suivante s’affiche : Unit 1 - Waiting to select management unit)> ___________Dell SupportAssist EULA__________________ I accept the terms of the license agreement.
receive related repair services from Dell. You further agree to allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dell's affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
with normal operation using the default system configuration. Note: You can exit the setup wizard at any point by entering [ctrl+z]. Would you like to run the setup wizard (you must answer this question within 60 seconds)? [Y/N] y Step 1: The system is not set up for SNMP management by default. To manage the switch using SNMP (required for Dell Network Manager) you can . Set up the initial SNMP version 2 account now. . Return later and set up other SNMP accounts.
Step 2: Now we need to set up your initial privilege (Level 15) user account. This account is used to login to the CLI and Web interface. You may set up other accounts and change privilege levels later. For more information on setting up user accounts and changing privilege levels, see the user documentation. To set up a user account: Please enter the user name.
Finally, set up the default gateway. Please enter the IP address of the gateway from which this network is reachable. [0.0.0.0]: 10.1.1.1 This is the configuration information that has been collected: SNMP Interface = “public”@10.1.2.100 User Account setup = admin Password = ******** VLAN1 Router Interface IP = 10.1.1.200 255.255.255.0 Default Gateway = 10.1.1.1 Step 6: If the information is correct, please enter (Y) to save the configuration and copy the settings to the start-up configuration file.
Les commutateurs Série N1100-ON prennent en charge les fonctions de commutation de base telles que les VLAN et le protocole spanning tree. Utilisez l’interface de gestion via le web ou via l’interface CLI pour configurer les caractéristiques requises par votre réseau.
Conformité avec les organismes Les commutateurs N1108T-ON, N1108P-ON, N1108EP-ON, N1124T-ON, N1124P-ON, N1148T-ON et N1148P-ON sont conformes aux exigences des organismes et de sécurité suivantes : Déclaration de la USA Federal Communications Commission (FCC) Cet équipement a été testé et déclaré conforme aux limites des appareils numériques de classe A définies à l’alinéa 15 du règlement de la FCC.
Figure 1-8. Déclaration du ministère canadien des Communications Normes de sécurité et certificats de conformité des organismes • IEC 62368-1, 2e édition • CUS UL 60950-1, 2e édition • Répond ou dépasse les exigences des tests de rigidité diélectrique et de continuité de la mise à la terre conformément au standard UL 60950-1.
• EN55032 • Japon : VCCI, classe A • Corée : KN32, classe A • Taïwan : CNS13438, classe A • États-Unis : FCC CFR47, alinéa 15, sous-partie B, classe A Immunité • EN 300 386 : Compatibilité électromagnétique pour l’équipement réseau • EN 55024 • EN 61000-3-2 : Limites pour les émissions de courant harmonique • EN 61000-3-3 : Limitation des variations de tension, des fluctuations de tension et du papillotement • EN 61000-4-2 ESD • EN 61000-4-3 : Essai d’immunité aux champs électromagnétiq
Switches Dell Comutadores N1108T-ON/ N1108P-ON/N1108EP-ON/ N1124T-ON/N1124P-ON/ N1148T-ON/N1148P-ON Guia de Noções Básicas Modelos normativos: E17W e E18W
Notas, avisos e advertências NOTA: uma NOTA contém informações importantes para ajudar você a usar melhor os recursos do seu comutador. AVISO: Um AVISO indica possíveis danos ao hardware ou perda de dados e ensina como evitar o problema. ADVERTÊNCIA: Uma ADVERTÊNCIA indica possíveis danos à propriedade, risco de lesões corporais ou mesmo risco de vida. Aviso sobre a bateria de lítio: • há perigo de explosão se a bateria for trocada incorretamente.
Índice 1 Introdução . . . . . . . . . . . . . . . . . . . . . . . . Visão geral do hardware Série N1100-ON . . . . . . . Consumo de energia de comutadores PoE Série N1100-ON . . . . . . . . . . . . . . . Sistema de ventilação 67 . . . . . . . . . . . . . . . 68 . . . . . . . . . . Instalação do N1108T-ON/N1108P-ON/ N1108EP-ON . . . . . . . . . . . . . . . . . . . . . Montar um comutador N1108T-ON/N1108P-ON usando a bandeja em série Dell . . . . . . . . .
4 Iniciar e configurar o comutador Série N1100-ON . . . . . . . . . . . . . . . . . . . . 77 Conectar um comutador Série N1100-ON em um terminal . . . . . . . . . . . . . . . . . . . . . . . . 78 Série N1100-ONConectar um comutador a uma fonte de alimentação . . . . . . . . . . . . . . . . . . . . . Conexão de alimentação CA e CC . 79 . . . . . . . . . 79 Inicializar o comutador Série N1100-ON . . . . . . . . . . 81 . . . . . . . . .
Introdução Este documento fornece informações básicas sobre os comutadores Switches Dell Série N1100-ON, inclusive a forma de instalar o comutador e executar a configuração inicial. Para obter informações sobre como configurar e monitorar os recursos do comutador, consulte o Guia de configuração usuário, que está disponível no site de suporte da Dell em dell.com/support. Consulte o site de suporte para obter as atualizações mais recentes de documentação e firmware.
Modelo Tensão de entrada Configuração de fonte Consumo de Potência de alimentação corrente contínua contínua máxima (A) máxima (W) N1108EP-ON 100V/60Hz Adaptador de energia externo 54VCC 1,62A 157W 110V/60Hz Adaptador de energia externo 54VCC 1,47A 157W 120V/60Hz Adaptador de energia externo 54VCC 1,35A 157W 220V/50Hz Adaptador de energia externo 54VCC 0,74A 157W 240V/50Hz Adaptador de energia externo 54VCC 0,67A 157W 100V/60Hz PSU principal 2,66A 260,66W 110V/60Hz PSU principal
Resumo do modelo Série N1100-ON Tabela 1-2.
Instalação do N1108T-ON/N1108PON/N1108EP-ON Montar um comutador N1108T-ON/N1108P-ON usando a bandeja em série Dell O conector de alimentação CA está no painel traseiro. ADVERTÊNCIA: Leia as informações de segurança em Informações sobre segurança e regulamentações, bem como as informações de segurança para outros comutadores que se conectam ou suportam o comutador. ADVERTÊNCIA: Não use kits de montagem em rack para sustentar o comutador sob mesas ou estantes ou para fixá-lo na parede.
3 Fixe o kit no rack com parafusos de rack ou porcas gaiola e parafusos de porca gaiola com arruelas (dependendo do tipo de rack que você possui). Aperte os parafusos na parte inferior antes de apertar os parafusos na parte superior. Montar um N1108T-ON/N1108P-ON/N1108EP-ON em um rack de dois postes usando suportes em L grandes NOTA: O conector de alimentação CA está no painel traseiro dos comutadores N1108TON/N1108P-ON. O conector de alimentação CC do N1108EP-ON fica no centro do painel traseiro.
3 Repita o processo no outro lado do comutador. 4 Insira o comutador e o conjunto do trilho no rack pela parte frontal do rack. Certifique-se de que os orifícios de montagem em rack no comutador estejam alinhados com os orifícios de montagem no rack. 5 Prenda o comutador ao rack com os parafusos do rack. Aperte o par inferior dos parafusos antes do par superior dos parafusos. Consulte Figura 1-3. Figura 1-3.
3 Insira os parafusos fornecidos nos orifícios do suporte de montagem em parede e aperte-os com uma chave de fenda. Consulte Figura 1-4. Figura 1-4. Inserir suportes de montagem 4 Repita o processo para instalar o suporte de montagem em parede no outro lado do comutador. 5 Coloque o comutador na parede no local onde ele está sendo instalado. 6 Marque os locais na parede onde os parafusos que prenderão o comutador deverão ser preparados.
Figura 1-5.
Instalação dos modelos N1124T-ON/ N1124P-ON/N1148T-ON/ N1148P-ON Montagem em rack dos comutadores N1124T-ON/ N1124P-ON/ N1148T-ON/ N1148P-ON ADVERTÊNCIA: Leia as informações de segurança em Informações sobre segurança e regulamentações, bem como as informações de segurança para outros comutadores que se conectam ou suportam o comutador. O conector de alimentação CA está no painel traseiro do comutador.
2 Insira os parafusos fornecidos nos orifícios de montagem em rack e aperte-os com uma chave de fenda. 3 Repita o processo para instalar o suporte de montagem em rack no outro lado do comutador. 4 Insira o comutador no rack de 48,26 cm (19") rack, garantindo de que os orifícios de montagem de rack no suporte se alinhem com os orifícios no rack. 5 Fixe o suporte no rack com parafusos de rack ou porcas gaiola e parafusos de porca gaiola com arruelas (dependendo do tipo de rack que você possui).
Iniciar e configurar o comutador Série N1100-ON O fluxograma a seguir fornece uma visão geral das etapas que você usa para fazer a configuração inicial depois que o comutador é desembalado e montado. Figura 1-7.
Conectar um comutador Série N1100-ON em um terminal Após completar todas as conexões externas, configure o comutador conectando a um terminal. NOTA: Antes de continuar, leia as Notas de versão do produto. Você pode fazer o download das Notas de versão no site de suporte da Dell em dell.com/support. NOTA: A Dell recomenda que você obtenha a versão mais recente da documentação do usuário no site de suporte da Dell em dell.com/support.
f Selecione a opção de teclas de Terminal para Função, Seta e Ctrl. Garanta que a configuração seja para teclas de terminal (e não para teclas do Windows). 3 Conecte o conector USB tipo B no cabo diretamente à porta do console do comutador. A porta de console Switches Dell está localizada no lado direito do painel frontal e está identificada com um símbolo |O|O|. NOTA: O acesso do console ao gerenciador de pilha está disponível através de qualquer porta do console através da CLI local.
Inicializar o comutador Série N1100-ON Quando a alimentação é ativada com o terminal local já conectado, o comutador passará pelo teste automático de inicialização (POST). O POST é executado toda vez que o dispositivo é inicializado e examina os componentes de hardware para determinar se o comutador está completamente operacional antes de ser completamente inicializado. Se o POST detectar um problema crítico, o fluxo do programa será interrompido.
Executar a configuração inicial do Série N1100-ON O procedimento de configuração inicial é baseado nas suposições a seguir: • O comutador Switches Dell nunca foi configurado antes. • O comutador Switches Dell foi inicializado com sucesso. • A conexão do console foi estabelecida e o prompt Assistente de configuração fácil Dell aparece na tela de um computador executando um software de emulação de terminal. A configuração inicial do comutador é efetuada através da porta do console.
Procedimento de configuração inicial Efetue a configuração inicial usando o Assistente de configuração fácil Dell ou usando a CLI. O assistente é iniciado automaticamente quando o arquivo de configuração do comutador está vazio. Saia do assistente a qualquer momento pressionando [Ctrl+Z], mas todos os parâmetros de configuração especificados serão descartados e o comutador usará os valores padrão.
Sessão de exemplo Esta seção descreve uma sessão Assistente de configuração fácil Dell. Os valores a seguir são usados na sessão de exemplo: • A string de comunidade SNMP a ser usada é public. • O endereço IP do sistema de gerenciamento de rede (NMS) é 10.1.2.100. • O nome de usuário é admin e a senha é admin123. • O endereço IP para a interface de roteamento de VLAN 1 é 10.1.1.200 com uma máscara de sub-rede de 255.255.255.0. • O gateway padrão é 10.1.1.1.
Exemplo do console Assistente de configuração fácil Dell O exemplo a seguir contém a sequência de prompts e as respostas associadas à execução de uma sessão de exemplo do Assistente de configuração fácil Dell, usando os valores de entrada listados anteriormente. Depois que o comutador concluir o POST e for inicializado, o sistema exibirá a seguinte caixa de diálogo: Unit 1 - Waiting to select management unit)> ___________Dell SupportAssist EULA__________________ I accept the terms of the license agreement.
receive related repair services from Dell. You further agree to allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dell's affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
with normal operation using the default system configuration. Note: You can exit the setup wizard at any point by entering [ctrl+z]. Would you like to run the setup wizard (you must answer this question within 60 seconds)? [Y/N] y Step 1: The system is not set up for SNMP management by default. To manage the switch using SNMP (required for Dell Network Manager) you can . Set up the initial SNMP version 2 account now. . Return later and set up other SNMP accounts.
Please enter the IP address of the Management System (A.B.C.D) or wildcard (0.0.0.0) to manage from any Management Station. [0.0.0.0]: 10.1.2.100 Step 2: Now we need to set up your initial privilege (Level 15) user account. This account is used to login to the CLI and Web interface. You may set up other accounts and change privilege levels later. For more information on setting up user accounts and changing privilege levels, see the user documentation. To set up a user account: Please enter the user name.
Step 5: Finally, set up the default gateway. Please enter the IP address of the gateway from which this network is reachable. [0.0.0.0]: 10.1.1.1 This is the configuration information that has been collected: SNMP Interface = “public”@10.1.2.100 User Account setup = admin Password = ******** VLAN1 Router Interface IP = 10.1.1.200 255.255.255.0 Default Gateway = 10.1.1.1 Step 6: If the information is correct, please enter (Y) to save the configuration and copy the settings to the start-up configuration file.
Para acessar a interface do administrador de comutador Dell OpenManage, digite o endereço IP da interface de gerenciamento VLAN 1 no campo de endereço de um navegador da Web. Para acessar o gerenciamento remoto para CLI, digite o endereço IP da interface de gerenciamento VLAN 1 em um cliente SSH ou Telnet. Opcionalmente, continue a usar a porta do console para o acesso ao CLI local ao comutador.
Conformidade com a Entidade Os comutadores N1108T-ON, N1108P-ON, N1108EP-ON, N1124T-ON, N1124P-ON, N1148T-ON e N1148P-ON estão em conformidade com os seguintes requisitos de segurança e da entidade: Declaração da Comissão Federal de Comunicações dos EUA Este equipamento foi testado e constatado como compatível com os limites de dispositivos digitais de Classe A, de acordo com as normas FCC Parte 15.
Figura 1-8. Declaração do Ministério de Comunicação do Canadá Padrões de segurança e certificações da entidade de conformidade • IEC 62368-1, 2ª edição • CUS UL 60950-1, 2ª edição • Atende ou supera os testes de continuidade de aterramento e de Hi Pot de acordo com a UL 60950-1.
• Europa: EN55032:2015 (CISPR 32), Classe A • EN55032 • Japão: VCCI Classe A • Coreia: KN32, Classe A • Taiwan: CNS13438, Classe A • EUA: FCC CFR47 Parte 15, Subparte B, Classe A Imunidade • EN 300 386 EMC para equipamentos de rede • EN 55024 • EN 61000-3-2 Emissões harmônicas atuais • EN 61000-3-3 Flutuações de tensão e tremulação • EN 61000-4-2 ESD • EN 61000-4-3 Imunidade radiada • EN 61000-4-4 EFT • EN 61000-4-5 Sobrecarga • 61000-4-6 Imunidade conduzida em baixa frequência
Conmutadores de Dell Conmutadores N1108T-ON/ N1108P-ON/N1108EP-ON/ N1124T-ON/N1124P-ON/ N1148T-ON/N1148P-ON Guía de introducción Modelos regulatorios: E17W y E18W
Notas, precauciones y avisos NOTA: Una NOTA le indica que hay información importante que le ayuda a hacer un mejor uso de su producto. PRECAUCIÓN: Una ADVERTENCIA indica un potencial daño al hardware o pérdida de datos y le informa cómo evitar el problema. AVISO: Una señal de PRECAUCIÓN indica la posibilidad de sufrir daño a la propiedad, heridas personales o la muerte. Precaución sobre la batería de litio: • Existe el peligro de explosión si una batería se reemplaza de forma incorrecta.
Contenido 1 Introducción . . . . . . . . . . . . . . . . . . . . . . N1100-ON Series Descripción general del hardware . 97 . . 97 . . . . . . . . . . . . . . . 99 Consumo de energía para conmutadores PoE N1100-ON Series . . . . . . . . . . . . . . . . Sistema de ventilación Resumen del modelo N1100-ON Series . 2 . . . . . . . . 99 N1108T-ON/N1108P-ON/Instalación de N1108EP-ON . . . . . . . . . . . . . . . . . . . . .
4 Inicio y configuración del conmutador N1100-ON Series . . . . . . . . . . . . . . . . . . 107 Conexión de un conmutador N1100-ON Series a un terminal . . . . . . . . . . . . . . . . . . . . . . 108 N1100-ON SeriesConexión de un conmutador a una fuente de alimentación . . . . . . . . . . . . . 109 . . . . . . 109 . . . . . . . 110 Conexión de la alimentación CA y CC Inicio del conmutador N1100-ON Series Cómo realizar la configuración inicial de N1100-ON Series . . . . . . . . . . . . . . .
Introducción Este documento proporciona información básica acerca de los conmutadores Conmutadores de Dell N1100-ON Series, incluyendo cómo instalar el conmutador y realizar la configuración inicial. Para obtener información acerca de cómo configurar y supervisar las características del conmutador, consulte la Guía de configuración del usuario, que está disponible en el sitio web de asistencia de Dell en dell.com/support.
Tabla 1-1.
Sistema de ventilación Un ventilador enfría los conmutadores N1108T-ON/N1108P-ON, y dos ventiladores enfrían los conmutadores N1024T-ON/N1024P-ON/N1048T-ON/ N1048P-ON. Los ventiladores no son sustituibles en campo. N1108EP-ON es un switch sin ventilador. Resumen del modelo N1100-ON Series Tabla 1-2.
N1108T-ON/N1108P-ON/Instalación de N1108EP-ON Montaje de un switch N1108T-ON/N1108P-ON mediante la bandeja de tándem de Dell El conector de alimentación de CA se encuentra en el panel posterior. AVISO: Lea la información de seguridad en Información reglamentaria y de seguridad, así como la información de seguridad para otros conmutadores que se conectan al conmutador o que son compatibles con este.
3 Fije el kit en el bastidor con los pernos o bien con las tuercas prisioneras y sus pernos y arandelas (según el tipo de bastidor de que disponga). Apriete los pernos en la parte inferior y después apriete los pernos en la parte superior. Montaje de un N1108T-ON/N1108P-ON/N1108EP-ON en un rack de dos postes con soportes L grandes NOTA: El conector de alimentación de CA se encuentra en el panel posterior de los switches N1108T-ON/N1108P-ON.
4 Inserte el ensamblaje de rieles y el switch en el rack desde la parte frontal del rack. Asegúrese de que los orificios de montaje en rack en el switch se alineen con los orificios de montaje del rack. 5 Fije el switch al rack mediante los tornillos. Ajuste el par de tornillos de la parte inferior antes de ajustar el de la parte superior. Consulte el apartado Figura 1-3. Figura 1-3.
Figura 1-4. Inserción de los soportes de montaje 4 Repita el proceso con el soporte de montaje en pared del otro lado del conmutador. 5 Coloque el conmutador en la pared en la ubicación donde se instalará el conmutador. 6 En la pared, marque las posiciones donde deberán ir los tornillos para sujetar el switch. 7 En las posiciones marcadas, taladre los orificios y coloque los ocho puntos de ancla enviados en los orificios.
Figura 1-5.
Instalación de N1124T-ON/N1124PON/N1148T-ON/ N1148P-ON Montaje en bastidor de un conmutador N1124T-ON/ N1124P-ON/ N1148T-ON/ N1148P-ON AVISO: Lea la información de seguridad en Información reglamentaria y de seguridad, así como la información de seguridad para otros conmutadores que se conectan al conmutador o que son compatibles con este. El conector de alimentación de CA se encuentra en el lado del conmutador.
2 Inserte los pernos suministrados en los orificios de montaje en bastidor y apriételos con un destornillador. 3 Repita el proceso con el soporte de montaje en bastidor del otro lado del conmutador. 4 Inserte el conmutador en el bastidor de 48,26 cm (19 pulg.), asegurándose de que los orificios de montaje en bastidor del soporte están alineados con los orificios de montaje del bastidor.
Inicio y configuración del conmutador N1100-ON Series El siguiente diagrama de flujo proporciona una descripción general de los pasos que debe seguir para realizar la configuración inicial una vez que el conmutador se haya desempaquetado y montado. Figura 1-7.
Conexión de un conmutador N1100-ON Series a un terminal Una vez realizadas todas las conexiones externas, configure el conmutador conectándolo a un terminal. NOTA: Lea las notas de publicación de este producto antes de continuar. Puede descargar las notas de publicación de la página web de asistencia de Dell en dell.com/support. NOTA: Dell recomienda encarecidamente que obtenga la versión más reciente de la documentación del usuario desde el sitio web de asistencia de Dell en dell.com/support.
e Establezca el modo de emulación de terminal en VT100. f Seleccione las teclas del terminal para Función, Flecha y Ctrl. Asegúrese de que la configuración es para las teclas del terminal (y no para las teclas de Microsoft Windows). 3 Conecte el conector USB tipo B del cable directamente al puerto de la consola del conmutador. El puerto de la consola Conmutadores de Dell se encuentra en el lado derecho del panel frontal y está etiquetado con un símbolo |O|O|.
Inicio del conmutador N1100-ON Series Cuando se enciende la alimentación con el terminal local ya conectado, el conmutador realiza una autoprueba de encendido (POST). La autoprueba POST se ejecuta cada vez que se inicializa el conmutador y comprueba los componentes de hardware para determinar si el conmutador está completamente operativo antes del inicio completo. Si la POST detecta un problema crítico, el flujo de programa se detiene.
Cómo realizar la configuración inicial de N1100-ON Series El procedimiento de configuración inicial se basa en los siguientes supuestos: • El conmutador Conmutadores de Dell nunca fue configurado. • El conmutador Conmutadores de Dell se ha iniciado correctamente. • La conexión de la consola se estableció y la petición Asistente de configuración rápida de Dell aparece en la pantalla de un equipo que ejecute software de emulación de terminal.
Procedimiento para la configuración inicial Realice la configuración inicial mediante Asistente de configuración rápida de Dell o mediante la CLI. El asistente se inicia automáticamente cuando el archivo de configuración del conmutador está vacío. Salga del asistente en cualquier momento con Ctrl+z, aunque se descartarán todos los parámetros de configuración especificados y el conmutador utilizará los valores predeterminados.
Ejemplo de sesión Esta sección describe una sesión Asistente de configuración rápida de Dell. Los siguientes valores se utilizan en la sesión de ejemplo: • La cadena de comunidad SNMP que se utiliza es pública. • La dirección IP del sistema de administración de red (NMS) es 10.1.2.100. • El nombre de usuario es admin y la contraseña es admin123. • La dirección IP para la interfaz de enrutamiento VLAN 1 es 10.1.1.200 con una máscara de subred 255.255.255.0.
Ejemplo de consola Asistente de configuración rápida de Dell El siguiente ejemplo contiene la secuencia de peticiones y respuestas asociadas a la ejecución de una sesión de ejemplo Asistente de configuración rápida de Dell, usando los valores de entrada presentados anteriormente. Cuando el conmutador finaliza la POST y se inicia, aparece el diálogo siguiente: Unit 1 - Waiting to select management unit)> ___________Dell SupportAssist EULA__________________ I accept the terms of the license agreement.
receive related repair services from Dell. You further agree to allow Dell to transmit and store the Collected Data from SupportAssist in accordance with these terms. You agree that the provision of SupportAssist may involve international transfers of data from you to Dell and/or to Dell's affiliates, subcontractors or business partners. When making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist.
with normal operation using the default system configuration. Note: You can exit the setup wizard at any point by entering [ctrl+z]. Would you like to run the setup wizard (you must answer this question within 60 seconds)? [Y/N] y Step 1: The system is not set up for SNMP management by default. To manage the switch using SNMP (required for Dell Network Manager) you can . Set up the initial SNMP version 2 account now. . Return later and set up other SNMP accounts.
Step 2: Now we need to set up your initial privilege (Level 15) user account. This account is used to login to the CLI and Web interface. You may set up other accounts and change privilege levels later. For more information on setting up user accounts and changing privilege levels, see the user documentation. To set up a user account: Please enter the user name.
Finally, set up the default gateway. Please enter the IP address of the gateway from which this network is reachable. [0.0.0.0]: 10.1.1.1 This is the configuration information that has been collected: SNMP Interface = “public”@10.1.2.100 User Account setup = admin Password = ******** VLAN1 Router Interface IP = 10.1.1.200 255.255.255.0 Default Gateway = 10.1.1.1 Step 6: If the information is correct, please enter (Y) to save the configuration and copy the settings to the start-up configuration file.
administración VLAN 1 en un cliente Telnet o SSH. De manera alternativa, continúe para utilizar el puerto de la consola para acceder al CLI local del conmutador. Los conmutadores N1100-ON Series admiten características de conmutación como VLAN y el protocolo de árbol de extensión. Utilice la interfaz de administración basada en web o la CLI para configurar las características que su red requiere.
Cumplimiento de normas de agencia Los switches N1108T-ON, N1108P-ON, N1108EP-ON, N1124T-ON, N1124P-ON, N1148T-ON y N1148P-ON cumplen con los siguientes requisitos de agencia y de seguridad. Declaración de la Comisión Federal de Comunicaciones de EE. UU. Este equipo ha sido probado y cumple con los límites establecidos para los dispositivos digitales de clase A, de conformidad con la parte 15 de las reglas de la FCC.
Figura 1-8. Declaración del departamento canadiense de comunicación Certificaciones de agencias de cumplimiento de normas y estándares de seguridad • IEC 62368-1, 2.ª edición • CUS UL 60950-1, 2.ª edición • Cumple con o supera los requisitos de UL 60950-1 de pruebas de continuidad de conexión a tierra y de alta tensión. • AS/NZS 60950 • CSA 60950-1-03, 2.ª edición • EN 60950-1, 2.ª edición • EN 60825-1, 1.
• Europa: EN55032:2015 (CISPR 32), clase A • EN55032 • Japón: VCCI, clase A • Corea: KN32, clase A • Taiwán: CNS13438, clase A • EE. UU.
Información NOM (solo para México) La información que se proporciona a continuación aparece en el dispositivo descrito en este documento, de conformidad con los requisitos de la Norma Oficial Mexicana (NOM): Exportador: Dell Inc. One Dell Way Round Rock, TX 78682 Importador: Dell México, S.A. de C.V Av. Javier Barros Sierra, no 540, Piso 10, Col. Lomas de Santa Fe Delegación Álvaro Obregón, Ciudad de México. C.P. 01219 R.F.C: DME9204099R6 Enviar a: Dell México, S.A. de C.V Av.
124 Guía de introducción
Guía de introducción 125
126 Guía de introducción
w w w .d el l .c om | d el l .