Dell PowerEdge R620 Owner's Manual Regulatory Model: E16S Series Regulatory Type: E16S001
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2013 Dell Inc.
Contents Notes, Cautions, and Warnings...................................................................................................2 1 About Your System......................................................................................................................9 Front-Panel Features And Indicators.......................................................................................................................9 LCD Panel Features............................................................
Operating With A Setup Password Enabled....................................................................................................32 Entering The UEFI Boot Manager...........................................................................................................................33 Using The Boot Manager Navigation Keys......................................................................................................33 Boot Manager Screen....................................................
Replacing The Internal USB Key......................................................................................................................57 Expansion Cards And Expansion-Card Risers........................................................................................................57 Expansion Card Installation Guidelines............................................................................................................57 Removing An Expansion Card......................................
Installing The Control Panel—8 Hard Drive System........................................................................................92 Removing The Control Panel—10 Hard Drive System.....................................................................................92 Installing The Control Panel—10 Hard Drive System......................................................................................93 VGA Module..........................................................................................
System Board Jumper Settings............................................................................................................................111 System Board Connectors....................................................................................................................................112 Disabling A Forgotten Password..........................................................................................................................114 7 Technical Specifications..............
1 About Your System Front-Panel Features And Indicators Figure 1. Front-Panel Features and Indicators—8 Hard Drive System Item Indicator, Button, or Connector 1 Power-on indicator, power button Icon Description The power-on indicator lights when the system power is on. The power button controls the power supply output to the system.
Item Indicator, Button, or Connector Icon Description NOTE: DVD devices are data only. 6 vFlash media card slot Allows you to insert a vFlash media card. 7 LCD menu buttons Allows you to navigate the control panel LCD menu. 8 LCD panel Displays system ID, status information, and system error messages. The LCD lights blue during normal system operation. The LCD lights amber when the system needs attention, and the LCD panel displays an error code followed by descriptive text.
Item Indicator, Button, or Connector Icon Description NOTE: On ACPI-compliant operating systems, turning off the system using the power button causes the system to perform a graceful shutdown before power to the system is turned off. 4 NMI button Used to troubleshoot software and device driver errors when running certain operating systems. This button can be pressed using the end of a paper clip.
Figure 3. LCD Panel Features Item Button Description 1 Left Moves the cursor back in one-step increments. 2 Select Selects the menu item highlighted by the cursor. 3 Right Moves the cursor forward in one-step increments. During message scrolling: • • • • Press once to increase scrolling speed Press again to stop Press again to return to default scrolling speed Press again to repeat the cycle Home Screen The Home screen displays user-configurable information about the system.
Option Description Set error Select SEL to display LCD error messages in a format that matches the IPMI description in the SEL. This is useful when trying to match an LCD message with an SEL entry. Select Simple to display LCD error messages in a simplified user-friendly description. See System Error Messages for a list of messages in this format. Set home Select the default information to be displayed on the LCD Home screen.
Electrical indicator Condition Corrective Action power supply or voltage regulator). Temperature indicator Condition Corrective Action The indicator blinks amber if the system experiences a thermal error (for example, a temperature out of range or fan failure). Ensure that none of the following conditions exist: • A cooling fan is removed or has failed. • System cover, cooling shroud, EMI filler panel, memorymodule blank, or back-filler bracket is removed. • Ambient temperature is too high.
NOTE: If the hard drive is in Advanced Host Controller Interface (AHCI) mode, the status indicator (on the right side) does not function and remains off. Drive-Status Indicator Pattern (RAID Only) Condition Blinks green two times per second Identifying drive or preparing for removal Off Drive ready for insertion or removal NOTE: The drive status indicator remains off until all hard drives are initialized after the system is turned on. Drives are not ready for insertion or removal during this time.
Item Indicator, Button, or Connector Icon Description To reset iDRAC (if not disabled in F2 iDRAC setup) press and hold for more than 15 seconds. 2 System identification connector Allows you to connect the optional system status indicator assembly through the optional cable management arm. 3 iDRAC7 Enterprise port Dedicated management port. NOTE: The port is available for use only if the iDRAC7 Enterprise license is installed on your system.
Item Indicator, Button, or Connector Icon Description 10 Hard Drive System When one of these buttons is pressed, the system status indicator on the back flashes until one of the buttons is pressed again. 8 Hard Drive System When one of these buttons is pressed, the LCD panel on the front and the system status indicator on the back flashes until one of the buttons is pressed again. Press to toggle the system ID on and off.
Item Indicator, Button, or Connector 12 Power supply (PSU2) Icon Description Or DC 750 W or 1100 W NIC Indicator Codes Figure 7. NIC Indicator 1. link indicator 2. activity indicator Indicator Indicator Code Link and activity indicators are off The NIC is not connected to the network. Link indicator is green The NIC is connected to a valid network at its maximum port speed (1 Gbps or 10 Gbps).
1. AC power supply status indicator/handle Figure 9. DC Power Supply Status Indicator 1. DC power supply status indicator Power Indicator Pattern Condition Not lit Power is not connected. Green The handle/LED indicator lights green indicating that a valid power source is connected to the power supply and that the power supply is operational. Flashing amber Indicates a problem with the power supply.
Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document. • The Getting Started Guide provides an overview of setting up your system, and technical specifications. This document is available online at www.dell.com/support/manuals. • The rack documentation included with your rack solution describes how to install your system into a rack, if required.
Using The System Setup And Boot Manager 2 System Setup enables you to manage your system hardware and specify BIOS-level options. The following keystrokes provide access to system features during startup: Keystroke Description Enters the System Setup. Enters System Services, which opens the Dell Lifecycle Controller 2 (LC2).
mode. Thereafter, you must boot the system in the same boot mode (BIOS or UEFI) to access the installed operating system. Trying to boot the operating system from the other boot mode will cause the system to halt at startup. NOTE: Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS and 32-bit operating systems do not support UEFI and can only be installed from the BIOS boot mode. NOTE: For the latest information on supported operating systems, go to dell.com/ossupport.
System Setup Main Screen NOTE: Press to reset the BIOS or UEFI settings to their default settings. Menu Item Description System BIOS This option is used to view and configure BIOS settings. iDRAC Settings This option is used to view and configure iDRAC settings. Device Settings This option is used to view and configure device settings. System BIOS Screen NOTE: The options for System Setup change based on the system configuration.
Menu Item Description System Service Tag Displays the system Service Tag. System Manufacturer Displays the name of system manufacturer. System Manufacturer Displays the contact information of the system manufacturer. Contact Information Memory Settings Screen Menu Item Description System Memory Size Displays the amount of memory installed in the system. System Memory Type Displays the type of memory installed in the system. System Memory Speed Displays the system memory speed.
Menu Item Description Alternate RTID (Requestor Transaction ID) Setting Allows you to allocate more RTIDs to the remote socket increasing cache performance between the sockets or work in normal mode for NUMA. By default, the Alternate RTID (Requestor Transaction ID) Setting is set to Disabled. Virtualization Technology Allows you to enable or disable the additional hardware capabilities provided for virtualization. By default, the Virtualization Technology option is set to Enabled.
SATA Settings Screen Menu Item Description Embedded SATA Allows the embedded SATA to be set to Off, ATA, AHCI, or RAID modes. By default, the Embedded SATA option is set to AHCI. Port E Auto enables BIOS support for the device attached to SATA port E. Off disables BIOS support for the device. By default, Port E is set to Auto. Port F Auto enables BIOS support for the device attached to SATA port F. Off disables BIOS support for the device. By default, Port F is set to Auto.
Menu Item Description User Accessible USB Allows you enable or disable the user accessible USB ports. Selecting Only Back Ports On Ports disables the front USB ports and selecting All Ports Off disables both front and back USB ports. By default, the User Accessible USB Ports option is set to All Ports On. Internal USB Port Allows you to enable or disable the internal USB port. By default, the Internal USB Port option is set to On.
Menu Item Description NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use console redirection by SOL, configure the same port address for console redirection and the serial device. External Serial Connector Allows you to associate the external serial connector to serial device 1, serial device 2, or remote access device. By default, the External Serial Connector option is set to Serial Device1. NOTE: Only Serial Device 2 can be used for SOL.
Menu Item Description NOTE: When C States is enabled in Custom mode, changing the Monitor/Mwait setting does not impact system power/performance. Memory Patrol Scrub Allows you to set the memory patrol scrub frequency. By default, the Memory Patrol Scrub option is set to Standard. Memory Refresh Rate Allows you to set the memory refresh rate. By default, the Memory Refresh Rate option is set to 1x. Memory Operating Voltage Allows you to set the DIMM voltage selection.
Menu Item Description BIOS Update Control Allows you to update the BIOS using either DOS or UEFI shell-based flash utilities. For environments that do not require local BIOS updates, it is recommended to set this field to Disabled. By default, the BIOS Update Control option is set to Unlocked. NOTE: BIOS updates using Dell Update Package are not affected by this option. Power Button Allows you to enable or disable the power button on the front of the system.
Setup password This is the password that you must enter to access and make changes to the BIOS or UEFI settings of your system. CAUTION: The password features provide a basic level of security for the data on your system. CAUTION: Anyone can access the data stored on your system if the system is running and unattended. NOTE: Your system is shipped with the system and setup password feature disabled.
To delete or change the existing System and/or Setup password: 1. To enter System Setup, press immediately after a power-on or reboot. 2. In the System Setup Main Menu, select System BIOS and press . The System BIOS screen is displayed. 3. In the System BIOS Screen, select System Security and press . The System Security screen is displayed. 4. In the System Security screen, verify that Password Status is Unlocked. 5.
NOTE: You can use the Password Status option in conjunction with the Setup Password option to protect the system password from unauthorized changes. Entering The UEFI Boot Manager NOTE: Operating systems must be 64-bit UEFI-compatible (for example, Microsoft Windows Server 2008 x64 version) to be installed from the UEFI boot mode. DOS and 32-bit operating systems can only be installed from the BIOS boot mode.
Boot Manager Screen Menu Item Description Continue Normal Boot The system attempts to boot to devices starting with the first item in the boot order. If the boot attempt fails, the system continues with the next item in the boot order until the boot is successful or no more boot options are found. BIOS Boot Menu Displays the list of available BIOS boot options (marked with asterisks). Select the boot option you wish to use and press .
For more information on using iDRAC, see the iDRAC7 User's Guide under Software → Systems Management → Dell Remote Access Controllers, at dell.com/support/manuals. Entering The iDRAC Settings Utility 1. Turn on or restart the managed system. 2. Press during Power-on Self-test (POST). 3. In the System Setup Main Menu page, click iDRAC Settings. The iDRAC Settings screen is displayed.
Installing System Components 3 Recommended Tools You may need the following items to perform the procedures in this section: • Key to the system keylock • #1 and #2 Phillips screwdrivers • T10 and T15 Torx screwdrivers • Wrist grounding strap connected to ground Following tools are required for assembling cables for a DC power supply unit (PSU), when available: • Wire-stripper pliers capable of removing insulation from size 10 AWG solid or stranded, insulated copper wire • AMP 90871-1 hand-crim
1. 2. 3. 4. release latch keylock front bezel locking hook Installing The Front Bezel 1. Hook the right end of the bezel onto the chassis. 2. Fit the free end of the bezel onto the system. 3. Secure the bezel with the keylock. Opening And Closing The System WARNING: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift the system by yourself.
Figure 11. Opening and Closing the System 1. system cover 2. latch 3. latch release lock Closing The System 1. Lift the latch on the cover. 2. Place the cover onto the chassis and offset the cover slightly back so that it clears the chassis hooks and lays flush on the chassis. 3. Push down the latch to move the cover into the closed position. 4. Rotate the latch release lock in a clockwise direction to secure the cover. 5.
Figure 12. Inside the System—8 Hard Drive System 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 40 control panel assembly cable securing clip cooling fans (7) cable securing bracket cooling shroud power supplies (2) chassis intrusion switch riser card 3 network daughter card riser card 2 11. 12. 13. 14. 15. 16. 17. 18.
Figure 13. Inside the System—10 Hard Drive System 1. 2. 3. 4. 5. 6. 7. 8. 9. control panel cable securing clip cooling fans (7) cable securing bracket cooling shroud power supplies (2) chassis intrusion switch riser card 3 network daughter card 10. 11. 12. 13. 14. 15. 16.
Figure 14. Removing and Installing the Cooling Shroud 1. cooling shroud Installing The Cooling Shroud CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
The system contains 24 memory sockets split into two sets of 12 sockets, one set per processor. Each 12-socket set is organized into four channels. In each channel, the release levers of the first socket are marked white, the second socket black, and the third socket green. NOTE: DIMMs in sockets A1 to A12 are assigned to processor 1 and DIMMs in sockets B1 to B12 are assigned to processor 2. Figure 15.
Processor 2 channel 0: slots B1, B5, and B9 channel 1: slots B2, B6, and B10 channel 2: slots B3, B7, and B11 channel 3: slots B4, B8, and B12 The following table shows the memory populations and operating frequencies for the supported configurations. DIMM Type DIMMs Populated/ Channel Operating Frequency (in MT/s) 1.5 V Maximum DIMM Rank/ Channel 1.
• Memory modules of different sizes can be mixed provided that other memory population rules are followed (for example, 2 GB and 4 GB memory modules can be mixed). • Populate four DIMMs per processor (one DIMM per channel) at a time to maximize performance. • If memory modules with different speeds are installed, they will operate at the speed of the slowest installed memory module(s) or slower depending on system DIMM configuration.
• Memory modules must be identical in size, speed, and technology. • DIMMs installed in memory sockets with white release tabs must be identical and similar rule applies for sockets with black and green release tabs. This ensures that identical DIMMs are installed in matched pairs for example, A1 with A2, A3 with A4, A5 with A6, and so on.
System Capacity DIMM Size (in Number of (in GB) GB) DIMMs DIMM Rank, Organization, and Frequency DIMM Slot Population NOTE: 16 GB DIMMs must be installed in slots numbered A1, A2, A3, A4, A5, A6, A7, and A8 and 8 GB DIMMs must be installed in slots A9 and A11. 384 32 12 LRDIMM, x4, 1333 MT/s A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, A12 Table 2.
System Capacity (in GB) DIMM Size (in GB) Number of DIMMs DIMM Rank, Organization, and Frequency DIMM Slot Population NOTE: 16 GB DIMMs must be installed in slots numbered A1, A2, A3, A4, B1, B2, B3, and B4 and 8 GB DIMMs must be installed in slots A5, A6, B5, and B6.
CAUTION: Handle each memory module only on either card edge, making sure not to touch the middle of the memory module. 5. Press down and out on the ejectors on each end of the socket until the memory module pops out of the socket. Figure 16. Removing and Installing a Memory Module 1. memory module 2. memory-module socket ejectors (2) 3. alignment key 6. Install memory-module blanks in vacant memory-module socket(s) to ensure proper system cooling. 7. Install the cooling shroud. 8. Close the system.
4. Locate the memory-module sockets. 5. Press the ejectors on the memory module socket down and out to allow the memory module to be inserted into the socket. If a memory module blank is installed in the socket, remove it. NOTE: Retain removed memory-module blank(s) for future use. CAUTION: Handle each memory module only on either card edge, making sure not to touch the middle of the memory module. 6.
Figure 17. Removing and Installing a 2.5 Inch Hard-Drive Blank 1. hard-drive blank 2. release button Installing A 2.5 Inch Hard-Drive Blank 1. If installed, remove the front bezel. 2. Insert the hard-drive blank into the hard-drive slot until the release button clicks into place. 3. If applicable, install the front bezel. Removing A Hot-Swap Hard Drive CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive installation.
Figure 18. Removing and Installing a Hot-Swap Hard Drive 1. release button 2. hard drive 3. hard-drive carrier handle Installing A Hot-Swap Hard Drive CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Removing A Hard Drive From A Hard-Drive Carrier 1. Remove the screws from the slide rails on the hard-drive carrier. 2. Lift the hard drive out of the hard-drive carrier. Figure 19. Removing and Installing a Hard Drive Into a Hard-Drive Carrier 1. hard-drive carrier 2. hard drive 3. screws (4) Installing A Hard Drive Into A Hard-Drive Carrier CAUTION: Many repairs may only be done by a certified service technician.
Optical Drive (Optional) Removing The Optical Drive CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
3. release tab Installing The Optical Drive CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. NOTE: This procedure applies only to the 8-hard drive system. 1.
Figure 21. Removing and Installing a Cooling Fan 1. cooling fans assembly 2. cooling fans (7) 3. cooling fan connectors (7) Installing A Cooling Fan CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Replacing The Internal USB Key CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
NOTE: A missing or an unsupported riser logs an SEL event. It does not prevent your system from powering on and no BIOS POST message or F1/F2 pause is displayed. Table 3.
Card Priority Card Type Systems Supporting up to 2 PCIe Expansion Cards Systems Supporting up to 3 PCIe Expansion Cards Slot Priority Max Allowed Slot Priority Max Allowed 10 1 Gb NICs 2 1 3, 2, 1 3 11 Non-RAID 2 1 1, 2, 3 3 Removing An Expansion Card CAUTION: Many repairs may only be done by a certified service technician.
3. expansion-card latch Installing An Expansion Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Figure 24. Removing and Installing the Expansion Card Riser 1 1. 2. 3. 4. 5. expansion-card riser 1 expansion card riser guide back (right) riser guide back (left) connector Figure 25.
1. connector 2. expansion card riser 3 4. If applicable, remove or install an expansion card on the riser. 5. Replace the expansion-card riser. 6. Close the system. 7. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. Installing Expansion-Card Risers CAUTION: Many repairs may only be done by a certified service technician.
1. SD vFlash card 2. SD vFlash card slot 4. To install the SD vFlash card, with the label side facing up, insert the contact-pin end of the SD card into the card slot on the module. NOTE: The slot is keyed to ensure correct insertion of the card. 5. Press inward on the card to lock it into the slot. Internal Dual SD Module NOTE: When the Redundancy option is set to Mirror Mode in the Integrated Devices screen of the System Setup, the information is replicated from one SD card to another.
Figure 27. Removing and Installing the Internal Dual SD Module 1. 2. 3. 4. 5. blue pull tab SD card 1 SD card 2 dual SD module connector on the system board Installing The Internal Dual SD Module CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Internal SD Card Removing An Internal SD Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Removing The Integrated Storage Controller CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Installing The Integrated Storage Controller CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Figure 28. Removing and Installing the Network Daughter Card 1. 2. 3. 4. captive screw sockets (2) connector on the system board captive screws (2) touch point 5. network daughter card 6. back panel slots for RJ-45 connectors Installing The Network Daughter Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
• Installing an additional processor • Replacing a processor NOTE: To ensure proper system cooling, you must install a processor blank and a heat-sink blank in any empty processor socket. Removing A Processor CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Figure 29. Removing and Installing the Heat Sink 1. 2. 3. 4. heat sink retention sockets (2) retention screws (2) processor CAUTION: The processor is held in its socket under strong pressure. Be aware that the release lever can spring up suddenly if not firmly grasped. 8. 9. 70 Position your thumb firmly over the processor socket-release lever near the unlock icon from the locked position by pushing down and out from under the tab.
Figure 30. Processor Shield Opening and Closing Lever Sequence 1. 2. 3. 4. 5. close-lock symbol processor socket-release lever processor processor socket-release lever open-lock symbol 10. Rotate the processor shield upward and out of the way. CAUTION: The socket pins are fragile and can be permanently damaged. Be careful not to bend the pins in the socket when removing the processor out of the socket. 11.
Figure 31. Removing and Installing a Processor 1. 2. 3. 4. 5. processor socket-release lever pin 1 indicator processor socket-release lever processor shield processor 6. ZIF socket 7. socket keys (4) 8. notches in processor (4) NOTE: After removing the processor, place it in an antistatic container for reuse, return, or temporary storage. Do not touch the bottom of the processor. Touch only the side edges of the processor.
3. Open the system. 4. Remove the cooling shroud. WARNING: The heat sink and processor are hot to the touch for some time after the system has been powered down. Allow the heat sink and processor to cool before handling them. CAUTION: Never remove the heat sink from a processor unless you intend to remove the processor. The heat sink is necessary to maintain proper thermal conditions. 5. Remove the heat sink/heat-sink blank and processor/processor blank, as applicable.
When only one power supply is installed, the power supply configuration is non-redundant (1 + 0). Power is supplied to the system only by the single power supply. NOTE: The DC power supply does not support mixed mode (one AC and one DC). NOTE: To avoid unplanned error logging, remove power from the source before unplugging the power cord from the 750 W DC power supply. NOTE: If two power supplies are used, they must be of the same type and have the same maximum output power.
Figure 32. Removing and Installing an AC Power Supply 1. 2. 3. 4. connector power supply release latch power supply handle Installing An AC Power Supply CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty.
Wiring Instructions For A DC Power Supply Your system supports up to two –(48–60) V DC power supplies (when available). WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself. All electrical wiring must comply with applicable local or national codes and practices.
3. Connect the safety ground wire to the grounding post on the back of the system using a #6-32 nut equipped with a locking washer. Figure 33. Assembling and Connecting the Safety Ground Wire 1. 2. 3. 4. 5. safety ground wire grounding post locking washer spring washer #6-32 nut Assembling The DC Input Power Wires WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds.
Figure 34. Assembling the DC Input Power Wires 1. 2. 3. 4. DC power socket rubber cap captive screws (2) DC power connector 5. wire –48 V 6. wire RTN 7. grounding wire Removing A DC Power Supply WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself. All electrical wiring must comply with applicable local or national codes and practices.
Figure 35. Removing and Installing a DC Power Supply 1. 2. 3. 4. 5. connector power supply power supply status indicator release latch power supply handle Installing A DC Power Supply WARNING: For equipment using –(48–60) V DC power supplies, a qualified electrician must perform all connections to DC power and to safety grounds. Do not attempt connecting to DC power or installing grounds yourself. All electrical wiring must comply with applicable local or national codes and practices.
Removing The Power Supply Blank CAUTION: To ensure proper system cooling, the power supply blank must be installed in the second power supply bay in a non-redundant configuration. Remove the power supply blank only if you are installing a second power supply. If you are installing a second power supply, remove the power supply blank in the bay by pulling outward on the blank. Figure 36. Removing and Installing the Power Supply Blank 1.
1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 2. Open the system. 3. Press the touch points and lift the system battery cover up and away from the network daughter card cooling shroud. Figure 37. Removing the System Battery Cover 1. system battery cover 2. network daughter card cooling shroud 3. touch points 4. Locate the battery socket.
6. To install a new system battery, hold the battery with the "+" facing up and slide it under the securing tabs at the positive side of the connector. 7. Press the battery straight down into the connector until it snaps into place. 8. Align the back of the system battery cover with the notch on the network daughter card cooling shroud and push the system battery cover down into the notches till it snaps into place. 9. Close the system. 10.
Figure 39. Removing and Installing the 2.5 Inch (x4) Hard-Drive Backplane 1. 2. 3. 4. 5. hard-drive backplane backplane signal cable backplane power cable release tab SAS A cable Figure 40. Cabling Diagram—2.
1. 2. 3. 4. 5. cable retention bracket system board integrated storage controller card SAS connector on system board SAS backplane Figure 41. Removing and Installing the 2.5 Inch (x4 SAS Hard-Drive and x2 Dell PowerEdge Express Flash [PCIe SSD]) Backplane 1. 2. 3. 4. 5. 84 backplane signal cable PCIe A cable backplane signal cable PCIe B cable backplane power cable 6. 7. 8. 9.
Figure 42. Cabling Diagram—Systems With the 2.5 Inch (x4 SAS and x2 PCIe SSD) Hard-Drive Backplane 1. 2. 3. 4. cable retention bracket system board PCIe SSD card integrated SAS controller card 5. SAS connector on system board 6. SAS and PCIe SSD backplane Figure 43. Removing and Installing the 2.
1. 2. 3. 4. 5. backplane signal cable backplane power cable SAS A cable release tabs (2) SAS B cable Figure 44. Cabling Diagram—2.5 Inch (x8) Systems 1. 2. 3. 4. 5.
Figure 45. Cabling Diagram—2.5 Inch (x8) Systems 1. 2. 3. 4. cable retention bracket system board SAS controller card SAS backplane Figure 46. Removing and Installing the 2.
1. 2. 3. 4. 5. SAS backplane backplane power cable SD signal cable backplane signal cable SD card socket 6. SAS cables (2) 7. release tabs (2) 8. hard-drive connector Figure 47. Cabling Diagram—2.5 Inch (x10) Systems 1. 2. 3. 4. 5. cable retention bracket system board integrated storage controller card SAS connector on system board SAS backplane expander card Installing The Hard-Drive Backplane CAUTION: Many repairs may only be done by a certified service technician.
1. Holding the blue tabs, align the slots on the hard-drive backplane with the tabs on the chassis. 2. Slide down the hard-drive backplane until the release tabs snaps into place. 3. Attach the SAS A cable to the SAS A connector on the hard-drive backplane and the SAS B cable to the SAS B connector. 4. Connect the power cable(s) to the hard-drive backplane. 5. Route the power/data cables along the chassis wall. 6. Install the hard drives in their original locations. 7. Close the system. 8.
Figure 48. Removing and Installing the Control Panel Board 1. 2. 3. 4. control panel board screws (2) control-panel cable display module cable Installing The Control Panel Board—8 Hard Drive System CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
1. If installed, remove the front bezel. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet and peripherals. 3. Open the system. CAUTION: The display module connector is a ZIF (zero insertion force) connector. Ensure that the locking tab on the connector is released before removal and insertion. The locking tab must be engaged after insertion. 4. Disconnect the display module cable from the control panel board. 5.
Installing The Control Panel—8 Hard Drive System CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1.
Figure 50. Removing and Installing the Control Panel 1. control panel release latch 2. J_CP connector on system board 3. control panel cable connecting to system board 4. J_FP_USB connector on system board 5. cable securing clip 6. screw 7. control panel Installing The Control Panel—10 Hard Drive System CAUTION: Many repairs may only be done by a certified service technician.
NOTE: To locate the connectors on the system board, see System Board Connectors. 5. Connect the control panel cable to the connectors on the system board (J_CP and J_FP_USB) and the hard-drive expander card. NOTE: Ensure that the control panel cable inside the system is routed along the chassis wall and secured using the cable securing bracket. 6. Close the system. 7. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. 8.
Figure 51. Removing and Installing the VGA Module 1. 2. 3. 4. control panel display module cable screw (top) VGA module cable 5. screw (bottom) 6. VGA module Installing The VGA Module NOTE: This procedure applies only to the 8-hard drive system. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
System Board Removing The System Board CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
a. mini SAS cable connector b. metal tab c. connector on the system board 6. Disconnect all other cables from the system board. CAUTION: Take care not to damage the system identification button while removing the system board from the chassis. 7. Grasp the system-board holder, lift the blue release pin, slide the system board toward the front of the system, and lift the system board out of the chassis.
Installing The System Board CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Unpack the new system board assembly.
Troubleshooting Your System 4 Safety First—For You And Your System CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
7. Power down all attached USB devices and disconnect them from the system. 8. Restart the system and, if your keyboard is functioning, enter the System Setup. Verify that all USB ports are enabled on the Integrated Devices screen, in the System Setup options. If your keyboard is not functioning, you can also use remote access. If the system is not accessible, reset the NVRAM_CLR jumper inside your system and restore the BIOS to the default settings. 9.
3. Disassemble components from the system: – Hard drives – Hard-drive backplane – USB memory key – Cooling shroud – Expansion-card risers (if present) – Expansion cards – Power supply(s) – Cooling-fan assembly (if present) – Cooling fans – Processor(s) and heat sink(s) 4. – Memory modules Let the system dry thoroughly for at least 24 hours. 5. Reinstall the components you removed in step 3. 6. Close the system. 7. Turn on the system and attached peripherals.
If the tests fail, see Getting Help. Troubleshooting The System Battery CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
Troubleshooting Cooling Fans CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Open the system. 2. Reseat the fan or the fan's power cable. 3.
15. As the system boots, observe any error message that is displayed and the diagnostic indicators on the front of the system. 16. If the memory problem is still indicated, repeat step 12 through step 15 for each memory module installed. If the problem persists after all memory modules have been checked, see Getting Help. Troubleshooting An Internal USB Key CAUTION: Many repairs may only be done by a certified service technician.
9. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. 10. Enter the System Setup and ensure that the Internal SD Card Port and Internal SD Card Redundancy mode is enabled. 11. Check if the SD card is functioning properly. If the problem persists, see Getting Help. Troubleshooting An Optical Drive CAUTION: Many repairs may only be done by a certified service technician.
Troubleshooting A Hard Drive CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. CAUTION: This troubleshooting procedure can erase data stored on the hard drive.
12. Reconnect the system to the electrical outlet, and turn on the system and attached peripherals. 13. Run the appropriate diagnostic test. For more information, see Using System Diagnostics. If the tests fail, see Getting Help. 14. For each expansion card you removed in step 10, perform the following steps: a. Turn off the system and attached peripherals, and disconnect the system from the electrical outlet. b. Open the system. c. Reinstall one of the expansion cards. d. Close the system. e.
Troubleshooting Processors CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1. Run the appropriate diagnostics test.
Using System Diagnostics 5 If you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance. The purpose of running system diagnostics is to test your system hardware without requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service and support personnel can use the diagnostics results to help you solve the problem.
The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the system. The diagnostics starts executing the tests on all the detected devices. System Diagnostic Controls Menu Description Configuration Displays the configuration and status information of all detected devices. Results Displays the results of all tests that are executed. System Health Provides the current overview of the system performance.
Jumpers And Connectors 6 System Board Jumper Settings For information on resetting the password jumper to disable a password, see Disabling A Forgotten Password. Table 6. System Board Jumper Settings Jumper PWRD_EN Setting (default) Description The password feature is enabled (pins 4–6). The password feature is disabled (pins 2–4). iDRAC local access is unlocked at the next AC power cycle. NVRAM_CLR (default) The configuration settings are retained at system boot (pins 1–3).
System Board Connectors Figure 53.
Item Connector Description 11 J_VIDEO_REAR Video connector 12 J_COM1 Serial connector 13 J_IDRAC_RJ45 iDRAC7 connector 14 J_CYC System identification connector 15 CYC_ID System identification button 16 J_RISER_2A Riser 2 connector 17 J_RISER_1A Riser 1 connector 18 TOUCH POINT Touch point for holding system board 19 J_RISER_2B Riser 2 connector 20 J_RISER_1B Riser 1 connector 21 J_STORAGE Storage controller card connector 22 J_SASX8 SATA connector 23 J_USB_INT Intern
Disabling A Forgotten Password The system's software security features include a system password and a setup password. The password jumper enables these password features or disables them and clears any password(s) currently in use. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
7 Technical Specifications Processor Processor type One or two Intel Xeon processor E5-2600 product family Expansion Bus Bus type PCI Express Generation 3 Expansion slots using riser card: Riser 1 (Slot 1) One half-height, half-length x8 link (Slot 2) One half-height, half-length x16 link Riser 2 (Slot 1) One half-height, half-length x8 link or one halfheight, half-length x16 link NOTE: Both processors must be installed to use the slots on riser 1 and the x16 link on riser 2.
Memory UDIMM Up to 128 GB Drives Hard drives 4–hard-drive systems Up to four 2.5 inch, internal, hot-swappable SAS, SATA, or Nearline SAS hard drives NOTE: Four–hard-drive systems support software RAID. For more information on software RAID, see the Dell PowerEdge RAID Controller (PERC) documentation at support.dell.com/manuals. 6–hard-drive systems Up to four 2.5 inch, internal, hot-swappable SAS, SATA, or Nearline SAS hard drives and up to two 2.
Connectors Internal USB One 4-pin, USB 2.0-compliant Internal Dual SD Module (IDSDM) Two optional flash memory card slots with the internal SD module NOTE: One card slot is dedicated for redundancy. Video Video type Integrated Matrox G200 Video memory 16 MB shared Expanded Operating Temperature NOTE: When operating in the expanded temperature range, system performance may be impacted.
Environmental NOTE: For additional information about environmental measurements for specific system configurations, see dell.com/environmental_datasheets. Temperature Maximum Temperature Gradient (Operating and Storage) 20 °C/h (36 °F/h) Storage Temperature Limits –40 °C to 65 °C (–40 °F to 149 °F) Temperature (Continuous Operation) Temperature Ranges (for altitude less than 950 m or 3117 ft) 10 °C to 35 °C (50 °F to 95 °F) with no direct sunlight on the equipment.
Environmental NOTE: This section defines the limits to help avoid IT equipment damage and/or failure from particulates and gaseous contamination. If it is determined that levels of particulates or gaseous pollution are beyond the limits specified below and are the reason for the damage and/or failures to your equipment, it may be necessary for you to re-mediate the environmental conditions that are causing the damage and/or failures.
System Messages 8 LCD Messages NOTE: Applicable only if your system has an LCD display. The LCD messages consist of brief text messages that refer to events recorded in the System Event Log (SEL). For information on the SEL and configuring system management settings, see the systems management software documentation. NOTE: If your system fails to boot, press the System ID button for at least 5 seconds until an error code is displayed on the LCD. Record the code, then see System Error Messages.
Error Code AMP0302 Message Information Message The system board current is greater than the upper warning threshold. Details System board current is outside of the optimum range. Action 1. Review system power policy. 2. Check system logs for power related failures. 3. Review system configuration changes. 4. If the issue persists, see Getting Help. AMP0303 Message The system board current is greater than the upper critical threshold.
Error Code ASR0003 BAT0002 BAT0017 CPU0000 CPU0001 CPU0005 Message Information Message The watchdog timer power cycled the system. Details The operating system or an application failed to communicate within the time-out period. The system was power-cycled. Action Check the operating system, application, hardware, and system event log for exception events. Message The system board battery has failed. LCD Message The system board battery has failed. Check battery.
Error Code CPU0010 CPU0023 CPU0204 Message Information Action Review the technical specifications for supported processor types. Message CPU is throttled. Details The CPU is throttled due to thermal or power conditions. Action Review system logs for power or thermal exceptions. Message CPU is absent. LCD Message CPU is absent. Check CPU. Action Verify processor installation. If present, re-seat the processor.
Error Code Message Information 2. Turn off the system and remove input power for one minute. 3. Ensure the processor is seated correctly. 4. Reapply input power and turn on the system. 5. If the issue persists, see Getting Help. CPU0702 Message CPU bus parity error detected. LCD Message CPU bus parity error detected. Power cycle system. Details System event log and operating system logs may indicate that the exception is external to the processor. Action 1.
Error Code Message Information 5. If the issue persists, see Getting Help. FAN0000 FAN0001 FAN1201 HWC1001 HWC2003 HWC2005 126 Message Fan RPM is less than the lower warning threshold. Details Fan operating speed is out of range. Action Remove and reinstall the fan. If the issue persists, see Getting Help. Message Fan RPM is less than the lower critical threshold. LCD Message Fan RPM is outside of range. Check fan. Details Fan operating speed is out of range.
Error Code MEM0000 MEM0001 MEM0007 MEM0701 MEM0702 MEM1205 Message Information Action Check if the cable is present, then reinstall or reconnect. Message Persistent correctable memory errors detected on a memory device at location(s) . Details This is an early indicator of a possible future uncorrectable error. Action Re-seat the memory modules. If the issue persists, see Getting Help . Message Multi-bit memory errors detected on a memory device at location(s) .
Error Code MEM1208 MEM8000 PCI1302 PCI1304 PCI1308 128 Message Information LCD Message Memory mirror lost on . Power cycle system. Details The memory may not be seated correctly, misconfigured, or has failed. Action Check the memory configuration. Re-seat the memory modules. If the issue persists, see Getting Help. Message Memory spare redundancy is lost. Check memory device at location . LCD Message Memory spare lost on . Power cycle system.
Error Code PCI1320 PCI1342 PCI1348 PCI1360 PDR0001 PDR1016 Message Information Action Cycle input power, update component drivers, if device is removable, reinstall the device. Message A bus fatal error was detected on a component at bus devicefunction . LCD Message Bus fatal error on bus device function . Power cycle system. Details System performance may be degraded, or system may fail to operate.
Error Code PST0128 PST0129 PSU0001 PSU0002 PSU0003 130 Message Information LCD Message Drive removed from disk drive bay . Check drive. Details The controller detected that the drive was removed. Action Verify drive installation. Re-seat the failed drive. If the issue persists, see Getting Help. Message No memory is detected. LCD Message No memory is detected. Inspect memory devices. Details System BIOS was unable to detect memory in the system.
Error Code PSU0006 PSU0016 Message Information Message Power supply type mismatch. LCD Message Power supply is incorrectly configured. Check PSU. Details Power supplies should be of the same input type and power rating. Action Install matched power supplies and review proper configuration in this manual. Message Power supply is absent. LCD Message PSU is absent. Check PSU. Details The power supply has been removed or has failed. Action 1.
Error Code PSU0034 Message Information Message An under voltage fault detected on power supply . LCD Message An under voltage fault detected on PSU . Check power source. Details This failure may be the result of an electrical issue with cables or subsystem components in the system. Action 1. Remove and reinstall the power supply. 2. Check cables and subsystem components in the system for damage. 3. If the issue persists, see Getting Help.
Error Code PSU1201 PSU1204 PWR1004 PWR1005 PWR1006 RFM1008 Message Information Message Power supply redundancy is lost. Details The power supply tries to operate in a degraded state. System Performance and power redundancy may be degraded or lost. Action Check input power. Reinstall the power supply. If the issue persists, see Getting Help. Message The power supplies are not redundant. Insufficient resources to maintain normal operations. LCD Message PSU redundancy degraded.
Error Code RFM1014 RFM1201 RFM2001 RFM2002 RFM2004 RFM2006 134 Message Information Details An error was reported during a SD card read or write. Action Reseat the flash media. If the problem persists, see Getting Help. Message Removable Flash Media is write protected. LCD Message Removable Flash Media is write protected. Check SD Card. Details The card is write-protected by the physical latch on the SD card. A write-protected card cannot be used.
Error Code SEC0031 SEC0033 SEL0006 SEL0008 SEL0012 SEL1204 Message Information Message The chassis is open while the power is on. LCD Message Intrusion detected. Check chassis cover. Details The chassis is open. System performance may be degraded, and security may be compromised. Action Close the chassis. Check system logs. Message The chassis is open while the power is off. LCD Message Intrusion detected. Check chassis cover. Details The chassis was opened while the power was off.
Error Code TMP0118 TMP0119 TMP0120 TMP0121 VLT0204 Message Information Action Re-configure system to the minimum supported configuration. If issues persists, contact support. Message The system inlet temperature is less than the lower warning threshold. LCD Message System inlet temperature is outside of range. Details Ambient air temperature is too cool. Action Check the system operating environment. Message The system inlet temperature is less than the lower critical threshold.
Error Code Message Information Action 1. Review system logs for power supply exceptions. 2. Re-configure the system to minimum configuration, inspect and reinstall system cables. 3. If the issue persists, see Getting Help. Warning Messages A warning message alerts you to a possible problem and prompts you to respond before the system continues a task. For example, before you format a hard drive, a message warns you that you may lose all data on the hard drive.
Getting Help 9 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be available in your area. To contact Dell for sales, technical support, or customer service issues: 1. Visit dell.com/support 2. Select your support category. 3.
