Dell EMC OpenManage Enterprise Modular Edition Version 1.00.10 for PowerEdge MX7000 Chassis RACADM Command Line Reference Guide February 2019 Rev.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2018 - 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents Chapter 1: Introduction................................................................................................................. 5 Supported RACADM Interfaces....................................................................................................................................... 5 RACADM Command Options............................................................................................................................................ 5 Other documents you may need......
cfgDNSDomainNameFromDHCP (Read or Write).............................................................................................. 26 cfgStorageModule.............................................................................................................................................................27 cfgStorageModuleStorageMode..............................................................................................................................27 cfgStorageModuleServiceTag................
1 Introduction This document provides information about the RACADM subcommands, supported RACADM interfaces, and property database groups and object definitions for Dell EMC OpenManage Enterprise Modular (OME – Modular). Topics: • • • Supported RACADM Interfaces RACADM Command Options Other documents you may need Supported RACADM Interfaces The RACADM command-line utility provides a scriptable interface that allows you to configure your OME - Modular.
Table 2. Supported RACADM interfaces Type Local RACADM Address SSH RACADM Remote RACADM OME-Modular No Yes Yes NOTE: Multiple instances of remote RACADM can be run on a management station. Displayable Characters Displayable characters include the following set: ● abcdefghijklmnopqrstuvwxwz ● ABCDEFGHIJKLMNOPQRSTUVWXYZ ● 0123456789~`!@#$%^&*()_+-={}[]|\:";'<>,.?/ Other documents you may need Table 3.
2 RACADM sub command details This section provides detailed descriptions about the RACADM subcommands, including the syntax and valid entries.
● # (pound) ● ASCII code 32 (space) NOTE: The - (dash) character cannot be the first character of the string, regardless of whether the string is quoted. There are different escaping rules for double quotation marks. There are different escaping rules for using single quotation mark and double quotation marks.
arp chassisaction config ...
Table 4. racadm arp (continued) Address HWtype HWaddress Flags Mask Iface 192.168.0.121 ether 90:b1:1c:f4:34:f4 C pub chassisaction Description Synopsis Input Executes the turn on, turn off, power cycle, or reset operation. racadm chassisaction [-m ] ● -m—Must be one of the following values: ○ chassis—Default state if -m is not specified. ○ switch-—Where n=1-6 ● —Must be one of the following values: ○ powerdown—Graceful shutdown of the module.
● View members present in a group: racadm chassisgroup view members ○ --pending— Pending requests to join the group. ○ --discovered— Discovered chassis in the wired environment. ● Executes on a standalone, adds a standalone chassis to the group: racadm chassisgroup add -g ● Executes on a standalone using lead IP, adds a standalone chassis to the group: racadm chassisgroup add -l 192.168.0.1 ● Admits a chassis to the chassis group racadm chassisgroup admit -m 192.168.0.
config Description Modifies RAC configuration properties. Synopsis racadm config -g -o
Synopsis racadm deploy -m server- -u root -p -s racadm deploy -m switch- -u root -p -d racadm deploy -a [server|switch] -u root -p Input ● -m——must be one of the following values: ○ server ○ switch ● -a—[server|switch]—applies options to all modules present in the chassis of the given module type; if specified must be one of the following values: ○ server ○ switch NOTE: If the module type is not specified, the default type is s
faultlist Description Displays the active error message in the chassis subsystem. Synopsis racadm faultlist view $ racadm faultlist view Example SubSystem = System.Modular.7 Message = CPU 1 is absent InstanceId = Fault#02200004#1 Severity = Critical MessageId = CPU0003 SubSystem = PowerSupply Message = The power input of power supply 1 is lost. InstanceId = Fault#02200005#1 Severity = Critical MessageId = PSU0003 SubSystem = PowerSupply Message = The power input of power supply 5 is lost.
● Display a single object from a particular group: racadm getconfig -g cfgLanNetworking -o cfgDNSRacName ● Display an indexed group: racadm getconfig -g cfgUserAdmin -o cfgUserAdminPassword -i 2 ● Display information about the service tag of the storage module: racadm getconfig -g cfgStorageModule -mm storage-<1 to 8> -o cfgStorageModuleServiceTag ● Display all available configuration groups: racadm getconfig -h getmodinfo Description Gets module configuration and status information.
● Display chassis network settings racadm getniccfg -m chassis getpbinfo Description Synopsis Input Gets power budget status information. If there is no power supply to the PSU, the output of the command is displayed as "failed". If there is a mismatch in the power source, for example, a PSU of 220 volts and PSU of 110 volts are combined, then the output of the command is displayed as "Configuration Error".
PS5 PS6 V N/A PSU.Slot.5 PSU.Slot.6 N/A 3000 W Absent N/A N/A Absent N/A N/A [Server Module Power Allocation Table] 3 7 SLOT-3 1 1 lade Type> De
[Power Budgeting] System Input Max Power Capacity Input Redundancy Reserve Input Power Allocated to Servers Input Power Allocated to Chassis Infrastructure Total Input Power Available for Allocation Standby Input Power Capacity = = = = = = 11571 W Not Applicable Not Applicable Not Applicable 2384 W (8134 BTU/h) Not Applicable getsensorinfo Description Displays system sensors.
● racadm getsensorinfo -c Sensor Type: Fan 1 Fan-1 2 Fan-2 3 Fan-3 4 Fan-4 5 Fan-5 6 Fan-6 7 Fan-7 8 Fan-8 9 Fan-9 Not OK OK OK OK OK Not OK OK OK OK N/A rpm 17174 rpm 17238 rpm 17081 rpm 14499 rpm N/A rpm 14502 rpm 14505 rpm 14479 rpm N/A N/A N/A N/A N/A N/A N/A N/A N/A Sensor Type: Temp 1 Chassis Inlet Temperature OK 47 Sensor Type: Power 1 PS-1 2 PS-2 3 PS-3 4 PS-4 5 PS-5 6 PS-6 Offline Slot Empt
ping Description Synopsis Sends ICMP echo packets on the network. racadm ping Input —The IP address of the remote endpoint to ping. Example To ping ip address 192.168.0.1 racadm ping 192.168.0.1 ping6 Description Synopsis Sends ICMP echo packets on the network. racadm ping6 Input —The IPv6 address of the remote endpoint to ping.
serveraction Description Manages the server or storage power. Supported actions are: ● powerdown—perform server power off ● powerup—perform server power on ● powercycle—perform server power cycle ● hardreset—force hard server power reset ● graceshutdown—perform graceful shutdown of server ● reseat—perform a virtual reseat of a server/storage NOTE: This action requires -f option to force the action.
Example ● Enable DHCP for a switch: racadm setniccfg -m switch-1 -d ● Configuration of switch to a static IPv4 address: racadm setniccfg -m switch-1 -s 192.168.0.120 255.255.255.0 192.168.0.1 ● Configuration of chassis to a static IPv4 address: racadm setniccfg -m chassis -s 192.168.0.120 255.255.255.0 192.168.0.
Example To execute a trace route for address FE80:0000:0000:0000:0202:B3FF:FE1E:8329: racadm traceroute6 FE80:0000:0000:0000:0202:B3FF:FE1E:8329 RACADM sub command details 23
3 OME Modular property database group and object descriptions Replace this text with your content. Topics: • • • • cfgLanNetworking cfgStorageModule cfgUserAdmin cfgRacTuning cfgLanNetworking This group contains parameters to configure OME Modular NIC for IPv4. One instance of the group is allowed. Some objects in this group may require management module NIC to be reset, which may cause a brief loss in connectivity.
2. racadm config -g cfglannetworking -o cfgDNSServersFromDHCP 0 3. racadm config -g cfglannetworking -o cfgDNSServer1 100.69.112.5 For Alternate DNS Server name use cfgDNSServer2. 4. racadm config -g cfglannetworking -o cfgDNSRegisterRac 1 To return to the original state if step 1 is applied. NOTE: You can modify the cfgDNSServer1 and cfgDNSServer2 only when cfgDNSServersFromDHCP is 0. Else, the static DNS server settings are ignored.
Legal Values ● 1 — True ● 0 — False Default 0 NOTE: For IPv6, only the DHCPv6 address or static address is registered. Example: racadm getconfig -g cfgLanNetworking cfgDNSServersFromDHCP=1 cfgDNSServer1=192.168.0.5 cfgDNSServer2=192.168.0.6 cfgDNSRacName=cmc-frankly cfgDNSDomainName=fwad.lab cfgDNSDomainNameFromDHCP=1 cfgDNSRegisterRac=1 cfgDNSRacName (Read or Write) Description Displays the management module name, which is Service Tag by default.
This property is used only if cfgNicUseDhcp is set to 1(true), or if both cfgIPv6Enable and cfgIPv6AutoConfig are set to 1(true).
cfgStorageModuleServiceTag Description Synopsis Input Displays the service tag. cfgStorageModuleServiceTag= cfgStorageModuleServiceTag= Example cfgStorageModuleServiceTag=MX0000 cfgStorageModuleAssetTag Description Synopsis Input Displays the asset tag. cfgStorageModuleAssetTag= cfgStorageModuleAssetTag Example cfgStorageModuleAssetTag=xxxxxx cfgStorageModuleConnectedSlots Description Synopsis Input Displays the connected slots.
Use this object with the config or getconfig subcommands. To use the command as follows: -i , supply an index group number. To use this object property, you must have the Chassis Configuration Administrator privilege. NOTE: You can configure a setting that does not have the hash sign (#) prefixed in the output. To modify a configurable object, use the —o option. cfgUserAdminPassword - Write Only Description The password for this user.
