Dell™ PowerEdge™ 6800 Systems Information Update 信息更新 Mise à jour des informations Aktuelle Informationen アップデート情報 설명서 갱신본 Actualización de información w w w. d e l l . c o m | s u p p o r t . d e l l .
Dell™ PowerEdge™ 6800 Systems Information Update w w w. d e l l . c o m | s u p p o r t . d e l l .
Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2006 Dell Inc. All rights reserved.
Information Update This document provides information for your system on the following topics: • Reconfiguring the system for regional power requirements • Processor upgrades • Adaptec SCSI Card 39160 expansion-card slot restrictions • System start-up behavior • Integrated NIC IPMI port functionality • Remote Access Controller card interaction with integrated video • System messages • Environmental data sheets • Removing and installing the cooling shroud • Linux operating system informati
Reconfiguring the System for Regional Power Requirements CAUTION: If you relocate a system operating in the 120–127 VAC or 200–240 VAC range to a different geographic area, ensure that jumper CB_TYPE matches the AC line voltage range of your new location. If the new power source is less than 120 VAC and you do not reconfigure jumper CB_TYPE for the lower voltage power source, damage to the system power cable or the system itself may occur.
Figure 1-1. Power Configuration Jumper Location Processor Upgrades If you add one or more processors to your system, ensure that all processors have the same stepping value and the same cache size and technology. If you install processors with different speeds, they will operate at the speed of the slowest processor. You must install all voltage regulator modules (VRMs) included in the upgrade kit, in addition to the processors.
System Start-Up Behavior The following system behaviors during system start-up are normal and do not indicate a problem with the system: • When AC power is applied to the system, if the System Setup program’s AC Power Recovery option is not set to allow the system to power up when AC power is applied, the cooling fans will spin-up briefly and then stop. (See your User’s Guide for information on the System Setup program.
Table 1-3. LCD Status Messages Line 1 Message Line 2 Message Causes Corrective Actions SYSTEM ID SYSTEM NAME SYSTEM ID is a unique name, This message is for information five characters or less, defined by only. the user. You can change the system ID SYSTEM NAME is a unique and name in the System Setup name, 16 characters or less, program. See your User's Guide defined by the user. for instructions. The system ID and name display under the following conditions: • The system is powered on.
Table 1-3. 8 LCD Status Messages (continued) Line 1 Message Line 2 Message Causes E0119 TEMP PLANAR System board temperature is out See "Troubleshooting System of acceptable temperature range. Cooling Problems" in your Installation and Troubleshooting Guide. E0212 PROC VTT Processor VTT voltage is out of acceptable voltage range. See "Troubleshooting Power Supplies" in your Installation and Troubleshooting Guide.
Table 1-3. LCD Status Messages (continued) Line 1 Message Line 2 Message Causes E0276 VRM # PG The voltage of the specified VRM See "Troubleshooting the is out of acceptable range. Microprocessors" in your Installation and Troubleshooting Guide. If the problem still persists, see "Getting Help" in your Installation and Troubleshooting Guide. E0276 VCACHE # PG The voltage of the specified VCACHE is out of acceptable range.
Table 1-3. 10 LCD Status Messages (continued) Line 1 Message Line 2 Message Causes Corrective Actions E0780 PROC n PRESENCE Microprocessor is not installed in socket n. Install a microprocessor in socket n. See "Installing a Processor" in your Installation and Troubleshooting Guide. E07F0 PROC n IERR Faulty or improperly installed microprocessor. See "Troubleshooting the Microprocessors" in your Installation and Troubleshooting Guide.
Table 1-3. LCD Status Messages (continued) Line 1 Message Line 2 Message Causes Corrective Actions E0880 PS REDUNDANCY LOST Power supply redundancy has Reinstall the power supply been lost because a power supply to restore redundancy. has been removed from the system. E0D76 BP DRIVE n Faulty or improperly installed hard drive or RAID controller.
Table 1-3. LCD Status Messages (continued) Line 1 Message Line 2 Message Causes EB10C ECC UNCORR ERR Uncorrectable ECC errors have See "Troubleshooting System occurred in system memory. The Memory" in your Installation affected memory bank may be and Troubleshooting Guide. specified. ECC UNCORR ERR BANK # 12 Corrective Actions EB113 I/O CHANNEL CHK System I/O channel check error has occurred. See "Getting Help" in your Installation and Troubleshooting Guide.
Table 1-3. LCD Status Messages (continued) Line 1 Message Line 2 Message Causes Corrective Actions EB113 CHIPSET ERR An error has occurred in the chipset. See "Troubleshooting the Microprocessors" in your Installation and Troubleshooting Guide. If the problem persists, see "Troubleshooting Expansion Cards" in your Installation and Troubleshooting Guide. If the problem still persists, see "Getting Help" in your Installation and Troubleshooting Guide.
Removing and Installing the Cooling Shroud To remove the cooling shroud, grasp each end of the shroud and lift the shroud straight up from the system. To install the cooling shroud, slowly lower the shroud straight down into the system and then press down on the four icons (above the latches) until the shroud snaps into place. See Figure 1-2. Figure 1-2.
Linux Operating System Information Booting Red Hat Enterprise Linux AS (Version 4) for Intel x86 With More than Eight Logical Processors A system running the Red Hat Enterprise Linux AS (version 4) for Intel x86 operating system will fail to boot if it is configured with more than eight logical processors. To work around this issue, pass the parameter apic=bigsmp to the kernel command line at system boot. A correction for this issue will be available in a future Red Hat Enterprise Linux Version 4 Update.
Microsoft Windows 2000 Installation Installation of Microsoft Windows 2000 Server or Microsoft Windows 2000 Advance Server is not supported on PowerEdge 6800 systems featuring dual-core processors with L3 cache. NOTE: Installation of Microsoft Windows 2000 Server or Microsoft Windows 2000 Advanced Server is supported on PowerEdge 6800 systems featuring single-core processors (with or without L3 cache) and dual-core processors with L2 cache only.
Dell™ PowerEdge™ 6800 系统 信息更新 w w w. d e l l . c o m | s u p p o r t . d e l l .
注、注意和警告 注:注表示可以帮助您更好地使用计算机的重要信息。 注意:注意表示可能会损坏硬件或导致数据丢失,并告诉您如何避免此类问题。 警告:警告表示可能会导致财产损失、人身伤害甚至死亡。 ____________________ 本文件中的信息如有更改,恕不另行通知。 © 2006 Dell Inc. 版权所有,翻印必究。 未经 Dell Inc. 书面许可,严禁以任何形式进行复制。 本文中使用的商标:Dell、DELL 徽标和 PowerEdge 是 Dell Inc. 商标; Intel 是 Intel Corporation 的注册商标; Microsoft 和 Windows 是 Microsoft Corporation 的注册商标,Windows Server 是 Microsoft Corporation 的商标; Red Hat 是 Red Hat Corporation 的注册商 标; SUSE 是 SUSE LINUX Products GmbH 的注册商标。 本文件中述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。Dell Inc.
信息更新 本说明文件针对您的系统提供了有关以下主题的信息: • 针对地区性的电源要求重新配置系统 • 处理器升级 • Adaptec SCSI Card 39160 扩充卡插槽限制 • 系统启动行为 • 集成 NIC IPMI 端口功能 • 远程访问控制器卡与集成视频的相互影响 • 系统信息 • 环境数据表 • 卸下和安装冷却通风罩 • Linux 操作系统信息 – 当系统配备 8 个以上逻辑处理器时引导适用于 Intel® x86 的 Red Hat® Enterprise Linux AS (第 4 版) – 对适用于 Intel 64 位扩展内存技术 (Intel EM64T) 的 Red Hat Enterprise Linux(第 4 版) 使用多于八个的逻辑处理器 – 重新引导用于 Intel 64 位扩展内存技术 (Intel EM64T) 的 Red Hat Enterprise Linux AS(第 4 版) – NIC 设备名称 • 在多于八个逻辑处理器时安装 Microsoft® Windows Server™ 2003 • M
针对地区性的电源要求重新配置系统 警告:如果将工作在 120-127 VAC 或 200-240 VAC 范围内的系统重新部署到另一个地区,应确保跳线 CB_TYPE 与新位置的交流线电压范围相符。 如果新电源低于 120 VAC 并且没有针对较低电压电源重新配置跳线 CB_TYPE,则可能会导致系统电源线或 系统本身损坏。 表 1-1 列出了交流线电压可能低于 120 V 的国家或地区。请确认您所在的特定位置的电源, 并根据需要重新配置 CB_TYPE 跳线。 表 1-1.
图 1-1.
系统启动行为 在系统启动期间,以下系统行为属于正常现象,并不表示系统有问题。 • 当交流电源施加在系统上时,如果系统设置程序的 AC Power Recovery(交流电源恢复)选项没有 设为允许系统在交流电源接通时启动,冷却风扇将会短暂地转动,然后停止。(有关系统设置程序 的信息,请参阅《用户指南》。) • 在系统通电之后,可能需要 30 秒或更长时间才能显示视频。 集成 NIC IPMI 端口功能 如果将集成 NIC 配置为用于传送智能平台管理接口(IPMI,Intelligent Platform Management Interface)直通流量,同时还将系统配置为使用同一个 IPMI 端口通过网络引导,则在系统引导期间, NIC 将无法用于传送管理流量。系统引导之后,IPMI 功能会自动恢复。 此外,如果将 NIC 配置为支持 IPMI 管理流量,则 NIC 驱动程序的大量传送卸载 (LSO,Large-Send Offload)功能将在该端口上禁用。 远程访问控制器卡与集成视频的相互影响 如果安装可选的远程访问控制器卡以用于远程系统管理,则系统前面板和后面板的视频端口 将被禁用。 系统
表 1-3.
表 1-3.
表 1-3.
表 1-3.
表 1-3.
环境数据表 有关特定系统配置的环境测量值的其它信息,请访问 www.dell.com/environment_datasheets。 卸下和安装冷却通风罩 要卸下冷却通风罩,抓住通风罩的每一端,从系统中竖直向上提起通风罩。要安装冷却通风罩, 缓慢将通风罩竖直向下放低到系统中,然后按下闩锁上的四个图标,直到通风罩卡入到位。 请参阅图 1-2。 图 1-2.
Linux 操作系统信息 当系统配备 8 个以上逻辑处理器时引导适用于 Intel x86 的 Red Hat Enterprise Linux AS(第 4 版) 如果一台运行适用于 Intel x86 的 Red Hat Enterprise Linux AS(第 4 版)操作系统的系统配置了 8 个以 上的逻辑处理器,系统将无法引导。要解决这一问题,请在系统引导时将参数 apic=bigsmp 传递到 内核命令行。在将来的 Red Hat Enterprise Linux 第 4 版更新中将提供此问题的修正。 对适用于 Intel EM64T 的 Red Hat Enterprise Linux(第 4 版)使用多于八个的逻辑处理器 适用于 Intel EM64T 的 Red Hat Enterprise Linux(第 4 版)操作系统存在一个限制,该限制导致操作 系统所使用的逻辑处理器不得超过八个,即使系统中的处理器多于八个也是如此。对于配备的逻辑处 理器超过八个的系统,此 Linux 操作系统将只识别和报告八个处理器。有关这一限制的详情,请参阅 Red Hat 网站 http://www.
F3227eb9.fm Page 30 Tuesday, September 5, 2006 11:14 AM Microsoft Windows 2000 安装 在配备双核处理器(带 L3 高速缓存)的 PowerEdge 6800 系统上,不支持安装 Microsoft Windows 2000 Server 或 Microsoft Windows 2000 Advance Server。 注:如果 PowerEdge 6800 系统配备的是单核心处理器(带或不带 L3 高速缓存)和只带 L2 高速缓 存的双核处理器,则支持安装 Microsoft Windows 2000 Server 或 Microsoft Windows 2000 Advanced Server。 可以通过以下方法之一获得处理器类型: • 检查您的系统采购订单详细信息。 • 检查系统启动屏幕。 • 在系统设置程序中检查 CPU Information(CPU 信息)。 控制台重定向 - 按键转义序列 下表更新了《用户指南》的“使用控制台重定向”部分中的功能键的按键转义序列。 表 1-4.
Systèmes Dell™ PowerEdge™ 6800 Mise à jour des informations w w w. d e l l . c o m | s u p p o r t . d e l l .
Remarques, avis et précautions REMARQUE : une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. AVIS : un AVIS vous avertit d'un risque de dommage matériel ou de perte de données et vous indique comment éviter le problème. PRÉCAUTION : une PRÉCAUTION indique un risque potentiel d'endommagement du matériel, de blessure corporelle ou de mort. ____________________ Les informations contenues dans ce document peuvent être modifiées sans préavis.
Mise à jour des informations Ce document traite des sujets suivants : • Reconfiguration du système en fonction de normes électriques locales • Mises à niveau des processeurs • Restriction liée à l'installation de la carte SCSI 39160 Adaptec dans un logement d'extension • Comportement du système au démarrage • Port IPMI intégré du NIC • Interaction de la carte RAC avec la vidéo intégrée • Messages du système • Feuilles techniques sur l'environnement système • Installation et retrait du carén
Reconfiguration du système en fonction de normes électriques locales PRÉCAUTION : si vous déplacez le système d'une région utilisant une alimentation de 120–127 ou 200–240 V.c.a vers une autre zone géographique, vérifiez que le cavalier CB_TYPE est sur la position appropriée pour la région de destination. Si vous ne réglez pas ce cavalier sur la tension la plus basse alors que la nouvelle source d'alimentation utilise une tension inférieure à 120 V.c.
Figure 1-1. Emplacement du cavalier de configuration de l'alimentation Mises à niveau des processeurs Si vous ajoutez un ou plusieurs processeurs au système, vérifiez que tous les processeurs ont le même numéro de série type (stepping) et utilisent une mémoire cache de même taille et basée sur la même technologie. Si les processeurs ont des vitesses différentes, ils fonctionneront tous à la vitesse du processeur le plus lent.
Test de la mémoire au démarrage du système Par défaut, l'option System Memory Testing (Test de la mémoire système) est désactivée dans le programme de configuration du système. Si elle est activée, la mémoire système est testée à chaque démarrage. Ce test peut durer plus longtemps sur les systèmes disposant d'une quantité de mémoire importante. Consultez le Guide d'utilisation pour plus d'informations sur le programme de configuration du système.
Messages système Le tableau 1-3 contient la liste à jour des messages d'état qui peuvent s'afficher sur l'écran LCD du panneau avant si une erreur mémoire se produit au démarrage du système. Pour plus d'informations sur les messages du système, voir la section “Messages système” dans le Guide d'installation et de dépannage. Tableau 1-3.
Tableau 1-3. 38 Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes Actions correctrices E1000 MISCONFIG Des modules VRM sont mal installés ou manquants. Voir “Installing a Processor VRM” (Installation d'un module VRM de processeur), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 E0212 E0212 VOLT PG n Causes Actions correctrices L'alimentation du système a dépassé la plage de tension autorisée ; installation incorrecte ou panne d'alimentation. Voir “Troubleshooting Power Supplies” (Dépannage des blocs d'alimentation), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. 40 Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes E0276 PROC # VCORE La tension VCORE du processeur Voir “Troubleshooting the spécifié est en dehors des limites Microprocessors” (Dépannage autorisées. des microprocesseurs), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes Actions correctrices E0276 PS AC CURRENT Le courant alternatif du bloc d'alimentation est en dehors des limites autorisées. Voir “Troubleshooting Power Supplies” (Dépannage des blocs d'alimentation), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 42 Causes Actions correctrices E0780 PROC n PRESENCE Le microprocesseur n'est pas installé dans le support n. Installez un microprocesseur dans le support n. Voir “Installing a Processor” (Installation d'un processeur), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage). E07F0 PROC n IERR Le microprocesseur est défectueux ou mal installé.
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes Actions correctrices E07FA PROC n THERMTRIP La température du microprocesseur spécifié est en dehors des limites autorisées et celui-ci s'est arrêté. Voir “Troubleshooting System Cooling Problems” (Dépannage des incidents de refroidissement du système), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 44 Causes Actions correctrices Voir “Troubleshooting Power Supplies” (Dépannage des blocs d'alimentation), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage). E0876 PS n PREDICTIVE La tension du bloc d'alimentation est en dehors des limites autorisées. Le bloc d'alimentation indiqué est défectueux ou mal installé.
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes Actions correctrices E0D76 SCSI CONNECTOR Le câble SCSI n'est pas connecté. Voir “Troubleshooting SCSI Hard Drives” (Dépannage des disques durs SCSI), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes Actions correctrices EB10C Des erreurs ECC ne pouvant pas être corrigées se sont produites dans la mémoire système. Le banc de mémoire affecté peut également être indiqué. Voir “Troubleshooting System Memory” (Dépannage de la mémoire système), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes Actions correctrices EB113 PCIE FATAL ERR Erreur fatale PCIe. Voir “Troubleshooting Expansion Cards” (Dépannage des cartes d'extension), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Tableau 1-3. Messages d'état affichés sur l'écran LCD (suite) Message sur Message sur la ligne 2 la ligne 1 Causes Actions correctrices EFFF2 ROMB PRESENCE Le contrôleur RAID intégré est activé. Ce message s'affiche uniquement à titre d'information. I0000 BIB Le contrôleur BMC ne parvient pas à lire le bloc initial du BIOS (BIB). Voir “Getting Help” (Obtention d'aide), dans le document Installation and Troubleshooting Guide (Guide d'installation et de dépannage).
Installation et retrait du carénage de ventilation Pour retirer le carénage de ventilation, saisissez-le à chaque extrémité puis soulevez-le pour l'extraire du système. Pour l'installer, abaissez-le doucement sur le système et appuyez sur les quatre icônes situées au-dessus des loquets, jusqu'à ce que le carénage se mette en place. Voir la figure 1-2. Figure 1-2.
Informations concernant le système d'exploitation Linux Démarrage de Red Hat Enterprise Linux AS version 4 pour Intel x86 sur les systèmes comprenant plus de huit processeurs logiques Les systèmes Red Hat Enterprise Linux AS version 4 pour Intel x86 ne peuvent pas démarrer s'ils sont configurés avec plus de huit processeurs logiques. Pour éviter ce problème, indiquez le paramètre apic=bigsmp sur la ligne de commande du noyau au démarrage du système.
F3227eb9.fm Page 51 Wednesday, September 6, 2006 3:43 PM Installation de Microsoft Windows 2000 L'installation de Microsoft Windows 2000 Server ou de Microsoft Windows 2000 Advanced Server n'est pas prise en charge sur les systèmes PowerEdge 6800 équipés de processeurs double cœur avec mémoire cache L3.
52 Mise à jour des informations
Dell™ PowerEdge™ 6800-Systeme Aktuelle Informationen w w w. d e l l . c o m | s u p p o r t . d e l l .
Anmerkungen, Hinweise und Warnungen ANMERKUNG: Eine ANMERKUNG macht auf wichtige Informationen aufmerksam, die die Arbeit mit dem Computer erleichtern. HINWEIS: Ein HINWEIS warnt vor möglichen Beschädigungen der Hardware oder vor Datenverlust und zeigt auf, wie derartige Probleme vermieden werden können. VORSICHT: Hiermit werden Sie auf eine potentiell gefährliche Situation hingewiesen, die zu Sachschäden, Verletzungen oder zum Tod führen könnte.
Aktuelle Informationen Dieses Dokument enthält aktuelle Informationen zum System.
Umkonfigurieren des Systems für regionale Stromversorgungsbedingungen VORSICHT: Wenn Sie ein System für die Betriebsbereiche 120-127 VAC oder 200-240 VAC in einen anderen geographischen Bereich verlegen, müssen Sie darauf achten, dass die Einstellung des Jumpers CB_TYPE der Netzspannung am neuen Standort entspricht.
Abbildung 1-1. Position des Jumpers für die Betriebsspannungsanpassung Prozessor-Upgrades Wenn Sie dem System einen oder mehrere Prozessoren hinzufügen, achten Sie darauf, dass alle Prozessoren hinsichtlich Stepping-Wert, Cache-Größe und Technologie gleich sind. Wenn Sie Prozessoren mit unterschiedlichen Taktfrequenzen installieren, werden sie mit der Frequenz des langsamsten Prozessors betrieben. Zusätzlich müssen Sie alle im Upgrade-Kit enthaltenen Spannungsreglermodule (VRMs) installieren.
Speicherprüfung bei Systemstart Die Option System Memory Testing im System-Setup-Programm ist standardmäßig deaktiviert. Wenn die Option aktiviert ist, wird der Systemspeicher bei jedem Systemstart überprüft. Bei Systemen mit großem Speicher dauert diese Überprüfung unter Umständen eine gewisse Zeit. (Informationen zum SystemSetup-Programm finden Sie im User’s Guide [Benutzerhandbuch].
Systemmeldungen Tabelle 1-3 enthält eine aktualisierte Liste mit Systemstatusmeldungen, die im Fall eines Speicherfehlers eventuell beim Systemstart auf der vorderen LCD-Anzeige erscheinen. Weitere Informationen über Systemmeldungen erhalten Sie im Abschnitt „Systemmeldungen“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung). Tabelle 1-3.
Tabelle 1-3. 60 Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung Ursachen Maßnahmen E1000 MISCONFIG Fehlende und falsch installierte Spannungsreglermodule (VRM). Siehe dazu „Installation eines Prozessor-Spannungsreglermoduls (VRM)“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung).
Tabelle 1-3. Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung Ursachen Maßnahmen E0212 VOLT PG n Video Grafikspannung ist außerhalb des zulässigen Bereichs. Lesen Sie den Abschnitt „Wie Sie Hilfe bekommen“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung). E0212 VOLT BATT ROMB Defekter RAID-Akku. Ersetzen Sie den RAID-Akku.
Tabelle 1-3. 62 Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung Ursachen Maßnahmen E0276 VRM # PG Die Spannung des angegebenen Spannungsreglermoduls (VRM) ist außerhalb des zulässigen Bereichs. Siehe „Fehlerbehebung bei den Mikroprozessoren“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung).
Tabelle 1-3. Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung Ursachen Maßnahmen E0412 RPM FAN n Angegebener Lüfter ist defekt, nicht ordnungsgemäß installiert oder fehlt. Siehe „Troubleshooting System Cooling Problems“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung). FAN REDUNDANCY LOST E0780 PROC # CONFIG ERR Der angegebene Prozessor weist einen Konfigurationsfehler auf.
Tabelle 1-3. 64 Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung E07FA PROC n THERMTRIP Angegebener Mikroprozessor befindet sich außerhalb des zulässigen Temperaturbereichs und wurde angehalten. Siehe „Troubleshooting System Cooling Problems“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung). Wenn das Problem weiterhin besteht, überprüfen Sie, ob die Kühlkörper der Mikroprozessoren ordnungsgemäß installiert sind.
Tabelle 1-3. Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung Ursachen Maßnahmen E0876 PS n AC LOST PS n AC RANGE Die Spannungsquelle für das angegebene Netzteil ist nicht verfügbar oder befindet sich außerhalb des zulässigen Bereichs. Überprüfen Sie die Wechselstromquelle für das angegebene Netzteil. E0880 PS REDUNDANCY LOST Die Lüfterredundanz ist aufgehoben, Installieren Sie das Netzteil da ein Netzteil aus dem System wieder, um die Redundanz entfernt wurde.
Tabelle 1-3. Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung EB107 PROC MACHINE CHK Mikroprozessor oder Systemplatine defekt oder nicht ordnungsgemäß installiert. Siehe „Fehlerbehebung bei den Mikroprozessoren“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung).
Tabelle 1-3. Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung Ursachen Maßnahmen EB113 PCI SYSTEM ERR PCI-Systemfehler ist aufgetreten. Siehe „Fehlerbehebung bei Erweiterungskarten“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung). Wenn das Problem weiterhin besteht, lesen Sie den Abschnitt „Wie Sie Hilfe bekommen“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung).
Tabelle 1-3. Meldungen auf der LCD-Statusanzeige (Fortsetzung) Zeile 1 Meldung Zeile 2 Meldung Ursachen Maßnahmen EB113 CHIPSET ERR Ein Fehler ist im Chipsatz aufgetreten. Siehe „Fehlerbehebung bei den Mikroprozessoren“ in der Installation and Troubleshooting Guide (Anleitung zur Installation und Fehlerbehebung).
Umwelt-Datenblätter Weitere Informationen über Umweltdaten bei spezifischen Systemkonfigurationen finden Sie unter www.dell.com/environment_datasheets. Entfernen und Installieren des Kühlgehäuses Um das Kühlgehäuse zu entfernen, fassen Sie es an beiden Enden an und heben Sie es dann gerade nach oben aus dem System. Um das Kühlgehäuse zu installieren, senken Sie das Blech gerade nach unten in das System ab.
Informationen zum Betriebssystem Linux Starten von Red Hat Enterprise Linux AS (Version 4) für Intel x86 mit mehr als acht logischen Prozessoren Ein System mit dem Betriebssystem Red Hat Enterprise Linux AS (Version 4) für Intel x86 lässt sich nicht starten, wenn es mit mehr als acht logischen Prozessoren konfiguriert ist. Um dieses Problem zu umgehen, übergeben Sie beim Systemstart auf der Kernel-Befehlszeile den Parameter apic=bigsmp.
F3227eb9.fm Page 71 Wednesday, September 6, 2006 3:48 PM Installation von Microsoft Windows 2000 PowerEdge 6800-Systeme, die Dual-Core-Prozessoren mit L3-Cache verwenden, laufen nicht unter den Betriebssystemen Microsoft Windows 2000 Server oder Microsoft Windows 2000 Advance Server. ANMERKUNG: PowerEdge 6800-Systeme, die Single-Core-Prozessoren mit oder ohne L3-Cache bzw.
72 Aktuelle Informationen
Dell™ PowerEdge™ 6800 システム アップデート情報 w w w. d e l l . c o m | s u p p o r t . d e l l .
メモ、注意、警告 メモ:コンピュータを使いやすくするための重要な情報を説明しています。 注意:ハードウェアの損傷やデータの損失の可能性を示し、その危険を回避するための方法を説明してい ます。 警告:物的損害、けが、または死亡の原因となる可能性があることを示します。 ____________________ 本書の内容は予告なく変更されることがあります。 © 2006 すべての著作権は Dell Inc. にあります。 Dell Inc. の書面による許可のない複製は、いかなる形態においても厳重に禁じられています。 本書で使用されている商標について:Dell、DELL ロゴ、および PowerEdge は Dell Inc.
アップデート情報 本書では、以下のトピックについて、ご使用のシステムに関する情報を提供します。 • ご使用になる地域の電源の要件に合わせたシステムの再設定 • プロセッサのアップグレード • Adaptec SCSI カード 39160 の拡張カードスロットの制限事項 • システム起動時の動作 • 内蔵 NIC IPMI ポートの機能 • リモートアクセスコントローラカードとオンボードビデオのやり取り • システムメッセージ • 環境データシート • エアフローカバーの取り外しと取り付け • Linux オペレーティングシステムの情報 – 9 つ以上の論理プロセッサを搭載した Red Hat® Enterprise Linux AS(バージョン 4) for Intel x86 の起動 – Red Hat Enterprise Linux(バージョン 4)for Intel Extended Memory 64 Technology (Intel EM64T)で 9 つ以上の論理プロセッサを使用する場合 – Red Hat Enterprise Linux AS
ご使用になる地域の電源の要件に合わせたシステムの再設定 警告:AC 120 ~ 127 V または 200 ~ 240 V の範囲で動作しているシステムを別の地域に移動する場合 は、ジャンパ CB_TYPE が新しい場所の AC ライン電圧範囲に適合することを確認してください。 新しい電源が AC 120 V を下回る場合は、ジャンパ CB_TYPE を低い電圧の電源向けに再設定しないと、 システムの電源ケーブルまたはシステム自体が損傷する可能性があります。 AC ライン電圧が 120 V を下回る可能性のある国の一覧を示します。システムをご使用にな 表 1-1 に、 る地域の電源を確認し、必要に応じて、CB_TYPE ジャンパを再設定してください。 表 1-1 AC ライン電圧が 120 V を下回る可能性のある地域 AC ライン電圧 国 100 V 日本、韓国、沖縄 105 V 韓国 110 V アングイラ、アゾレス諸島、ベルギー、ベリーズ、ボリビア、ブラジル、コロンビ ア、キュラソー島、ドミニカ共和国、エクアドル、エルサルバドル、フランス、グ アム、ガイアナ、ハイチ、ホンジュラス、ジャマイカ
図 1-1 電源構成のジャンパの位置 プロセッサのアップグレード 1 つまたは複数のプロセッサをシステムに追加する場合は、すべてのプロセッサのステッピング番 号、キャッシュサイズ、およびテクノロジが同じであることを確認してください。動作速度の異な るプロセッサを取り付けると、遅い方のプロセッサの速度で動作します。 プロセッサに加えて、アップグレードキットに含まれているすべての電圧レギュレータモジュール (VRM)を取り付ける必要があります。プロセッサと VRM の取り付けの詳細については、 『インストー ル&トラブルシューティング』の「プロセッサ」を参照してください。 Adaptec SCSI カード 39160 の拡張カードスロットの制限事項 Microsoft Windows 2000 Server オペレーティングシステムを実行しているシステムに Adaptec SCSI Card 39160 を追加し、Dell™ Remote Access Controller 4/P(DRAC 4/P)カードが拡張カード スロット 7 に取り付けられている場合、Adaptec 39160 カードは拡張カードス
システム起動時のメモリテスト セットアップユーティリティの システムメモリテスト オプションは、デフォルトで無効に設定され ています。このオプションを有効にすると、システムを起動するたびにシステムメモリのテストが実 行されます。メモリの容量が大きい構成のシステムは、メモリテストに要する時間が長くなる場合が あります。セットアップユーティリティについては、『ユーザーズガイド』を参照してください。 システム起動時の動作 システム起動時における以下のシステム動作は正常であり、システムに問題があることを示すもの ではありません。 • セットアップユーティリティの AC Power Recovery オプションが AC 電力の供給時にシス テムの電源が入るように設定されていない状態で、システムに AC 電力を供給した場合に、 冷却ファンが一時的にスピンアップした後、停止する(セットアップユーティリティについて は、『ユーザーズガイド』を参照してください)。 • システムの電源を入れた後、ビデオが表示されるまでに 30 秒またはそれ以上かかる場合 がある。 内蔵 NIC IPMI ポートの機能 内蔵 NIC を
システムメッセージ 表 1-3 には、メモリエラーが発生した場合にシステム起動時に前面パネルの LCD に表示されるシス テムステータスメッセージの新しい一覧を示します。システムメッセージの詳細については、 『インストール & トラブルシューティング』の「システムメッセージ」を参照してください。 表 1-3 LCD ステータスメッセージ 1 行目の 2 行目の メッセージ メッセージ 原因 対応処置 SYSTEM ID SYSTEM ID は、 ユーザーが定 義する 5 文字以下の一意の名 前です。 このメッセージは情報の表示の みです。 SYSTEM NAME システムの ID と名前はセット アップユーティリティで変更で きます。手順については、 『ユー ザーズガイド』を参照してくだ システム ID とシステム名は、 さい。 以下の状況で表示されます。 • システムの電源が入っ ている。 • 電源が切れており、アク ティブ POST エラーが表示さ れている。 SYSTEM NAME は、ユーザー が定義する 16 文字以下の一 意の名前です。 E0000 OVRFLW CHECK L
表 1-3 LCD ステータスメッセージ (続き) 80 1 行目の 2 行目の メッセージ メッセージ 原因 E0119 TEMP AMBIENT システム環境温度が許容範囲 『インストール&トラブル 外です。 シューティング』 の 「Troubleshooting System Cooling Problems」を参照して ください。 E0119 TEMP PROC # 表示されているプロセッサの 『インストール&トラブル 温度が許容範囲外です。 シューティング』 の「システム冷 却問題のトラブルシューティン グ」を参照してください。 E0119 TEMP PLANAR システム基板の温度が許容範 『インストール&トラブル 囲外です。 シューティング』 の「システム冷 却問題のトラブルシューティン グ」を参照してください。 E0212 PROC VTT プロセッサ VTT の電圧が許 容範囲外です。 E0212 VOLT PG n 電源ユニットの電圧が許容範 『インストール&トラブル 囲外です。 電源ユニットに障 シューティング』 の「電源ユニッ 害があるか、または正し
表 1-3 LCD ステータスメッセージ (続き) 1 行目の 2 行目の メッセージ メッセージ 原因 対応処置 E0276 PROC # STATUS プロセッサに障害があるか、 『インストール&トラブル または正しく取り付けられ シューティング』 の「マイクロプ ていません。 ロセッサのトラブルシューティ ング」 を参照してください。 E0276 PROC # VCORE 表示されているプロセッサの 『インストール&トラブル VCORE 電圧が許容範囲 シューティング』 の「マイクロプ 外です。 ロセッサのトラブルシューティ ング」 を参照してください。問 題が解決しない場合は、 『インス トール&トラブルシューティン グ』の「困ったときは」を参照し てください。 E0276 VRM # PG 表示されている VRM の電 圧が許容範囲外です。 『インストール&トラブル シューティング』 の「マイクロプ ロセッサのトラブルシューティ ング」 を参照してください。問 題が解決しない場合は、 『インス トール&トラブルシューティン グ』の「困ったときは」を参照し てください。 E0
表 1-3 LCD ステータスメッセージ (続き) 1 行目の 2 行目の メッセージ メッセージ E0412 RPM FAN n FAN REDUNDANCY LOST 82 原因 対応処置 表示されている冷却ファンに 『インストール&トラブル 障害があるか、取り付けが正 シューティング』 の「システム冷 しくないか、または取り付け 却問題のトラブルシューティン られていません。 グ」を参照してください。 E0780 PROC # CONFIG ERR 表示されているプロセッサの 『インストール&トラブル 構成にエラーがあります。 シューティング』 の「マイクロプ ロセッサのトラブルシューティ ング」 を参照してください。 E0780 PROC # DISABLED 表示されているプロセッサは 『インストール&トラブル 無効になっています。 シューティング』 の「マイクロプ ロセッサのトラブルシューティ ング」 を参照してください。 E0780 PROC n PRESENCE マイクロプロセッサがソケッ ト n に取り付けられていま せん。 E07F0 PROC n IERR
表 1-3 LCD ステータスメッセージ (続き) 1 行目の 2 行目の メッセージ メッセージ 原因 対応処置 E07FA PROC n THERMTRIP 表示されているマイクロプロ 『インストール&トラブル セッサが温度の許容範囲を超 シューティング』 の「インストー えたため動作を停止しま ル&トラブルシューティング」 した。 を参照してください。問題が解 決しない場合は、 マイクロプロ セッサのヒートシンクが正しく 取り付けられていることを確認 します。 『インストール&トラブ ルシューティング』の「プロセッ サの取り外し」を参照してくだ さい。 メモ:システムの電源コードを AC コンセントから抜いてもう 一度つなぐか、Server Assistant または BMC 管理ユーティリ ティのいずれかを使用して SEL をクリアするまで、LCD にはこ のメッセージが表示されます。 ユーティリティの使い方につい ては、『Dell OpenManage ベー スボード管理コントローラユー ザーズガイド』を参照してくだ さい。 E0876 PS n MISSING PS n STATUS
表 1-3 LCD ステータスメッセージ (続き) 1 行目の 2 行目の メッセージ メッセージ 原因 対応処置 E0D76 BP DRIVE n ハードドライブまたは RAID コントローラに障害がある か、 または正しく取り付けら れていません。 E0D76 1x2 Drive n 1x2 バックプレーン上の表示 『インストール&トラブル されているドライブが故障し シューティング』 の「SCSI ハー ているか、 正しく取り付けら ドドライブのトラブルシュー れていないか、 または RAID ティング」、 「RAID コントロー コントローラが故障している ラカードのトラブルシューティ か、 正しく取り付けられてい ング」 、および「内蔵 RAID コン ません。 トローラのトラブルシューティ ング」 を参照してください。 E0D76 SCSI CONNECTOR SCSI ケーブルが接続されてい 『インストール&トラブル ません。 シューティング』 の「SCSI ハー ドドライブのトラブルシュー ティング」を参照してください。 EB107 PROC BUS PERR PRO
表 1-3 LCD ステータスメッセージ (続き) 1 行目の 2 行目の メッセージ メッセージ 原因 EB10C システムメモリに修正不能な 『インストール & トラブル ECC エラーが発生しました。 シューティングガイド』の「シス エラーの発生したメモリバン テムメモリのトラブルシュー クが表示される場合があり ティング」を参照してください。 ます。 ECC UNCORR ERR ECC UNCORR ERR BANK # 対応処置 EB113 I/O CHANNEL CHK システム I/O チャネルの チェックエラーが発生し ました。 『インストール&トラブル シューティング』 の「困ったとき は」を参照してください。 EB113 PCI PARITY ERR PCI パリティーエラーが発生 しました。 『インストール&トラブル シューティング』 の「拡張カード のトラブルシューティング」を 参照してください。問題が解決 しない場合は、 『インストール& トラブルシューティング』の 「困ったときは」を参照してくだ さい。 EB113 PCI SYSTEM ERR P
表 1-3 LCD ステータスメッセージ (続き) 1 行目の 2 行目の メッセージ メッセージ 原因 対応処置 EB113 CHIPSET ERR チップセットにエラーが発生 『インストール&トラブル しました。 シューティング』 の「マイクロプ ロセッサのトラブルシューティ ング」 を参照してください。問 題が解決しない場合は、 『インス トール&トラブルシューティン グ』の「拡張カードのトラブル シューティング」 を参照してく ださい。問題が解決しない場合 は、 『インストール&トラブル シューティング』 の「困ったとき は」を参照してください。 EFFF2 ROMB PRESENCE 内蔵 RAID コントローラがア クティブです。 I0000 BIB BMC が BIB(BIOS Initial 『インストール&トラブル Block)を読み取ることができ シューティング』 の「困ったとき ません。 は」を参照してください。 IB110 SBE LOG DISABLED シングルビットエラーのログ が無効になっています。 情報表示のみです。 IB110 LOGGING
環境データシート 特定のシステム構成でのその他の環境条件の詳細については、 www.dell.
Linux オペレーティングシステムの情報 8 つ以上の論理プロセッサを搭載した Red Hat Enterprise Linux AS(バージョン 4) for Intel x86 の起動 8 つ以上の論理プロセッサを使用するシステム構成で Red Hat Enterprise Linux AS(バージョン 4) for Intel x86 オペレーティングシステムを実行しようとすると、起動しない場合があります。この 問題を回避するには、システム起動時にカーネルコマンドラインにパラメータ apic=bigsmp をパ スします。この問題を修正するパッチは、将来の Red Hat Enterprise Linux バージョン 4 アップ デートで用意される予定です。 Red Hat Enterprise Linux(バージョン 4)for Intel EM64T で 9 つ以上の論理プロセッサを使 用する場合 システムに 9 つ以上のプロセッサがある場合でも、Red Hat Enterprise Linux(バージョン 4)for Intel EM64T の制限により、この OS で使用できる論理プロセッサ
F3227eb9.
コンソールリダイレクション ― エスケープキーシーケンス 次の表は、『ユーザーズガイド』の「コンソールリダイレクションの使い方」にあるファンク ションキーのエスケープキーシーケンスを更新するものです。 表 1-4 90 ファンクションキーのエスケープシーケンス キー 対応するシーケンス <1> <2> <3> <4> <5> <6> <7> <8> <9> <0> <@> アップデート情報
Dell™ PowerEdge™ 6800 시스템 설명서 갱신본 w w w. d e l l . c o m | s u p p o r t . d e l l .
참고 , 알림 , 주의 참고: 참고는 컴퓨터를 보다 효율적으로 사용하는데 도움이 되는 중요 정보를 제공합니다. 주의사항: 알림은 하드웨어의 손상 또는 데이터 유실 위험을 설명하며, 이러한 문제를 방지할 수 있는 방법을 알려줍니다. 주의: 주의는 재산상의 피해나 심각한 부상 또는 사망을 유발할 수 있는 위험이 있음을 나타냅니다. ____________________ 본 설명서에 수록된 정보는 사전 통보 없이 변경될 수 있습니다. © 2006 Dell Inc. All rights reserved. 어떠한 경우에도 Dell Inc.의 사전 승인 없이 무단 복제하는 행위는 엄격하게 금지되어 있습니다. 본 설명서에 사용된 상표인 Dell, DELL 로고 및 PowerEdge는 Dell Inc.의 상표입니다. Intel은 Intel Corporation의 등록 상표입니다.
설명서 갱신본 본 설명서는 다음 내용에 관한 시스템의 정보를 제공합니다.
지역별 전원 사양에 따른 시스템 재구성 주의 : 120–127 VAC 또는 200–240 VAC 범위에서 작동하는 시스템을 다른 지역으로 옮기려는 경우 점퍼 CB_TYPE 가 새 지역의 AC 회선 전압 범위와 일치하는지 확인하십시오 . 새로운 전원이 120 VAC 보다 낮고 저전압 전원에 맞춰 점퍼 CB_TYPE 를 재구성하지 않을 경우 시스템 전원 케이블이나 시 스템 자체에 손상이 발생할 수 있습니다 . 표 1-1은 AC 회선 전압이 120 V보다 낮을 수 있는 국가의 목록입니다. 특정 위치의 전원을 확인하고 필요 한 경우 CB_TYPE 점퍼를 재구성하십시오. 표 1-1.
그림 1-1. 전원 구성 점퍼 위치 프로세서 업그레이드 시스템에 하나 이상의 프로세서를 추가하는 경우 모든 프로세서가 동일한 스테핑 값을 가지며 동일한 캐쉬 크기 및 기술을 사용하는지 확인하십시오. 속도가 다른 프로세서를 설치할 경우 가장 느린 프로세 서의 속도로 작동됩니다. 프로세서 외에도 업그레이드 키트에 포함된 모든 VRM (Voltage Regulator Module)을 설치해야 합니다. 프로세서 및 VRM 설치에 대한 자세한 내용은 설치 및 문제 해결 설명서의 "프로세서"를 참조하십시오. Adaptec SCSI 카드 39160 확장 카드 슬롯 제한 Adaptec SCSI 카드 39160을 Microsoft Windows 2000 Server 운영 체제를 실행하고 있는 시스템에 추가 하고 Dell™ Remote Access Controller 4/P(DRAC 4/P) 카드가 확장 카드 슬롯 7에 설치되어 있는 경우 확 장 카드 슬롯 2에 Adaptec 39160 카드가 설치되어야 합니다.
시스템 시동 시 동작 시스템 시작 중에 다음과 같은 시스템 동작은 정상적인 동작으로서 시스템 문제가 아닙니다. • AC 전원 공급 시 시스템 전원을 켤 수 있도록 시스템 설치 프로그램의 AC Power Recovery (AC 전 원 복구) 옵션을 설정하지 않은 경우에는 시스템에 AC 전원이 공급될 때 냉각 팬이 잠시 회전하다 가 정지합니다. (시스템 설치 프로그램에 대한 자세한 내용은 사용 설명서를 참조하십시오.) • 시스템 전원이 켜진 후 비디오가 표시되는 데 30초 이상이 걸릴 수 있습니다. 내장 NIC IPMI 포트 기능 IPMI(Intelligent Platform Management Interface) Pass-Through 트래픽용 내장 NIC를 구성하고 동일한 IPMI 포트를 사용하여 네트워크에서 부팅하도록 시스템을 구성하는 경우 시스템 부팅 중에 관리 트래 픽에 NIC을 사용할 수 없게 됩니다. 시스템 부팅이 완료되면 IPMI 기능이 자동으로 복원됩니다.
표 1-3. LCD 상태 메시지 ( 계속 ) 라인 1 메시지 라인 2 메시지 원인 E0000 OVRFLW CHECK LOG LCD 오버플로 메시지. 최대 세 개의 오류 메시지를 LCD에 순차적으로 표시할 수 있습니다. 네 번째 메시지가 표 준 오버플로 메시지로 표시됩 니다. 조치 이벤트에 대한 세부사항은 SEL 을 참조하십시오. E1000 FAIL SAFE Failsafe 이벤트. 이벤트 로그를 캡쳐하고 설치 및 문제 해결 설명서의 "도움말 얻기"를 참조하십시오. E1000 MISCONFIG VRM이 설치되어 있지 않거나 잘못 설치되었습니다. 설치 및 문제 해결 설명서의 "프로세서 VRM 설치"를 참조 하십시오. VRM의 설치 및 구 성이 제대로 이루어졌다고 생 각되면 설치 및 문제 해결 설 명서의 "도움말 얻기"를 참조 하십시오. E0119 TEMP AMBIENT 시스템 온도가 적당한 범위를 벗어납니다.
표 1-3. LCD 상태 메시지 ( 계속 ) 98 라인 1 메시지 라인 2 메시지 원인 조치 E0212 VOLT BATT ROMB 결함 있는 RAID 전지 RAID 전지를 교체하십시오. 설치 및 문제 해결 설명서의 "선택적인 통합된 RAID 컨트롤러 활성화"를 참조하십시오. E0212 VOLT BATT CMOS 시스템 전지에 결함이 있습 니다. 설치 및 문제 해결 설명서의 "시스템 전지 문제 해결"을 참조하십시오. 설치 및 문제 해결 설명서의 "도움말 얻기" 를 참조하십시오. E0276 PROC # STATUS 프로세서에 결함이 있거나 잘못 설치되었습니다. 설치 및 문제 해결 설명서의 "마이크로프로세서 문제 해 결"을 참조하십시오. E0276 PROC # VCORE 지정한 프로세서의 VCORE 전압이 적당한 범위를 벗어납 니다. 설치 및 문제 해결 설명서의 "마이크로프로세서 문제 해 결"을 참조하십시오.
표 1-3. LCD 상태 메시지 ( 계속 ) 라인 1 메시지 라인 2 메시지 원인 조치 E0412 RPM FAN n FAN REDUNDANCY LOST 지정한 냉각 팬에 결함이 있거 나 잘못 설치되었거나 없습 니다. 설치 및 문제 해결 설명서의 "시스템 냉각 문제점 해결"을 참조하십시오. E0780 PROC # CONFIG ERR 지정한 프로세서에 구성 오류 가 있습니다. 설치 및 문제 해결 설명서의 "마이크로프로세서 문제 해 결"을 참조하십시오. E0780 PROC # DISABLED 지정한 프로세서가 비활성화되 어 있습니다. 설치 및 문제 해결 설명서의 "마이크로프로세서 문제 해 결"을 참조하십시오. E0780 PROC n PRESENCE 마이크로프로세서가 n 소켓에 설치되지 않았습니다. 마이크로프로세서를 n 소켓 에 설치하십시오. 설치 및 문 제 해결 설명서의 "프로세서 설치" 를 참조하십시오.
표 1-3. LCD 상태 메시지 ( 계속 ) 100 라인 1 메시지 라인 2 메시지 원인 조치 E0876 PS n MISSING PS n STATUS 지정한 전원 공급 장치에서 전 원을 사용할 수 없습니다. 지정 한 전원 공급 장치가 잘못 설치 되었거나 결함이 있습니다. 설치 및 문제 해결 설명서의 "전원 공급 장치 문제 해결" 을 참조하십시오. E0876 PS n PREDICTIVE 전원 공급 장치 전압이 적당한 범위를 벗어납니다. 지정한 전 원 공급 장치가 잘못 설치되었 거나 결함이 있습니다 설치 및 문제 해결 설명서의 "전원 공급 장치 문제 해결" 을 참조하십시오. E0876 PS n AC LOST PS n AC RANGE 지정한 전원 공급 장치의 전원 을 사용할 수 없거나 적당한 범 위를 벗어납니다. 지정한 전원 공급 장치의 AC 전원을 확인하십시오.
표 1-3. LCD 상태 메시지 ( 계속 ) 라인 1 메시지 라인 2 메시지 EB107 PROC MACHINE CHK 설치된 마이크로프로세서나 시 스템 보드에 결함이 있거나 잘 못 설치되었습니다. EB107 PROC HOT 프로세서가 적당한 온도 범위 를 벗어났고 작동이 정지되었 습니다. 설치 및 문제 해결 설명서의 "시스템 냉각 문제 해결"을 참조하십시오. ECC UNCORR ERR 시스템 메모리에 복구할 수 없 는 ECC 오류가 발생했습니다. 영향을 받은 메모리 뱅크가 지 정될 수 있습니다. 설치 및 문제 해결 설명서의 "시스템 메모리 문제 해결"을 참조하십시오. EB10C ECC UNCORR ERR BANK # 원인 조치 설치 및 문제 해결 설명서의 "마이크로프로세서 문제 해 결"을 참조하십시오. 문제가 계속되면 설치 및 문제 해결 설명서의 "도움말 얻기"를 참 조하십시오. EB113 I/O CHANNEL CHK 시스템 I/O 채널 점검 오류가 발생했습니다.
표 1-3. LCD 상태 메시지 ( 계속 ) 라인 1 메시지 라인 2 메시지 원인 조치 EB113 CHIPSET ERR 칩셋에 오류가 발생했습니다. 설치 및 문제 해결 설명서의 "마이크로프로세서 문제 해 결"을 참조하십시오. 문제가 계속되면 설치 및 문제 해결 설명서의 "확장 카드 문제 해 결"을 참조하십시오. 문제가 계속되면 설치 및 문제 해결 설명서의 "도움말 얻기"를 참 조하십시오. EFFF2 ROMB PRESENCE 통합된 RAID 컨트롤러가 활성화되었습니다. 참조용입니다. I0000 BIB BMC가 BIB(BIOS Initial Block) 를 읽을 수 없습니다. 설치 및 문제 해결 설명서의 "도움말 얻기"를 참조하십시 오. IB110 SBE LOG DISABLED 단일 비트 오류 로그가 비활성 화되어 있습니다. 참조용입니다. IB110 LOGGING DISABLED BIOS 로깅이 비활성화되어 있 습니다. 참조용입니다.
냉각기 덮개 제거 및 설치 냉각기 덮개를 분리하려면 덮개의 각 끝을 잡고 시스템에서 덮개를 수직으로 들어 올립니다. 냉각기 덮 개를 설치하려면 덮개를 시스템에 똑바로 놓은 다음 덮개가 제자리로 들어갈 때까지 래치 위의 아이콘 4개를 아래로 누릅니다. 그림 1-2를 참조하십시오. 그림 1-2.
Linux 운영 체제 정보 8개 이상의 논리 프로세서를 가지는 시스템에 Intel x86용 Red Hat Enterprise Linux AS (버전 4) 부팅 Intel x86 운영 체제용 Red Hat Enterprise Linux AS(버전 4)를 실행하는 시스템은 8개 이상의 논리 프 로세서로 구성되는 경우 부팅에 실패합니다. 이 문제를 해결하려면 apic=bigsmp 매개변수를 시스 템 부팅 시 커널 명령줄로 전달하십시오. 이 문제는 추후 Red Hat Enterprise Linux 버전 4 Update에 서 해결될 것입니다. Intel EM64T 용 Red Hat Enterprise Linux (Version 4) 에 8 개 이상의 논리 프로세서 사용 Intel EM64T용 Red Hat Enterprise Linux (version 4) 운영 체제의 제한으로 인해 시스템에 더 많은 프로 세서가 있을 경우 운영 체제에서 8개 이상의 논리 프로세서를 사용하게 됩니다.
F3227eb9.fm Page 105 Tuesday, September 5, 2006 3:07 PM Microsoft Windows 2000 설치 Microsoft Windows 2000 Server 또는 Microsoft Windows 2000 Advance Server 설치는 L3 캐쉬의 듀얼 코어 프로세서가 탑재된 PowerEdge 6800 시스템에서는 지원되지 않습니다. 참고: Microsoft Windows 2000 Server 또는 Microsoft Windows 2000 Advanced Server 설치는 단일 코어 프로세서(L3 캐쉬 장착 또는 미장착) 및 L2 캐쉬의 듀얼 코어 프로세서가 탑재된 PowerEdge 6800 시스템에서는 지원됩니다. 프로세서 종류는 다음 방법 중 하나를 사용하여 알아낼 수 있습니다. • 시스템 구매 주문서를 확인합니다. • 시스템 시작 화면을 확인합니다. • 시스템 설치 프로그램에서 CPU Information(CPU 정보)을 확인합니다.
106 설명서 갱신본
Sistemas Dell™ PowerEdge™ 6800 Actualización de información w w w. d e l l . c o m | s u p p o r t . d e l l .
Notas, avisos y precauciones NOTA: una NOTA proporciona información importante que le ayudará a utilizar mejor el ordenador. AVISO: un AVISO indica la posibilidad de daños en el hardware o la pérdida de datos, e informa de cómo evitar el problema. PRECAUCIÓN: un mensaje de PRECAUCIÓN indica el riesgo de daños materiales, lesiones corporales o incluso la muerte. ____________________ La información contenida en este documento puede modificarse sin previo aviso. © 2006 Dell Inc.
Actualización de información En este documento se proporciona información sobre los temas siguientes relativos al sistema: • Nueva configuración del sistema según los requisitos regionales de alimentación • Adición de procesadores • Restricciones para la ranura de la tarjeta de expansión Adaptec SCSI 39160 • Comportamiento de inicio del sistema • Funciones de puerto IPMI de NIC integrada • Interacción de la tarjeta controladora de acceso remoto con las funciones de vídeo integradas • Mensajes d
Nueva configuración del sistema según los requisitos regionales de alimentación PRECAUCIÓN: si traslada un sistema que funciona en el rango de 120 a 127 V o de 200 a 240 V CA a un área geográfica diferente, compruebe que el puente CB_TYPE se corresponda con el rango de voltaje de línea de CA de la nueva ubicación.
Figura 1-1. Ubicación del puente de configuración de alimentación Adición de procesadores Si añade al sistema uno o varios procesadores, asegúrese de que todos los procesadores tengan el mismo número de versión y de que el tamaño de caché y la tecnología sean iguales. Si instala procesadores de velocidades diferentes, funcionarán a la velocidad del procesador más lento. Debe instalar todos los módulos reguladores de voltaje (VRM) incluidos en el kit de actualización, además de los procesadores.
Prueba de memoria al iniciar el sistema La opción System Memory Testing (Prueba de memoria del sistema) del programa de configuración del sistema está desactivada de manera predeterminada. Si se activa esta opción, se realizará una prueba de memoria del sistema cada vez que se inicie el sistema. En los sistemas con grandes configuraciones de memoria, la prueba de memoria puede tardar más tiempo en completarse.
Tabla 1-3. Mensajes de estado de la pantalla LCD Línea 1 mensaje Línea 2 mensaje Causas Acciones correctivas SYSTEM ID SYSTEM NAME SYSTEM ID es un nombre exclusivo de cinco caracteres como máximo definido por el usuario. Este mensaje es meramente informativo. SYSTEM NAME es un nombre exclusivo de 16 caracteres como máximo definido por el usuario. La ID y el nombre del sistema aparecen en las siguientes condiciones: • El sistema está encendido.
Tabla 1-3. 114 Mensajes de estado de la pantalla LCD (continuación) Línea 1 mensaje Línea 2 mensaje Causas Acciones correctivas E0119 TEMP PROC # La temperatura del procesador especificado se encuentra fuera del intervalo de temperaturas aceptable. Consulte “Solución de problemas de refrigeración del sistema” en la Guía de instalación y solución de problemas. E0119 TEMP PLANAR La temperatura de la placa base se encuentra fuera del intervalo de temperaturas aceptable.
Tabla 1-3. Mensajes de estado de la pantalla LCD (continuación) Línea 1 mensaje Línea 2 mensaje Causas E0276 PROC # VCORE El voltaje VCORE del procesador Consulte “Solución de problemas especificado se encuentra fuera de los microprocesadores” en la del intervalo aceptable. Guía de instalación y solución de problemas. Si el problema persiste, consulte “Obtención de ayuda” en la Guía de instalación y solución de problemas.
Tabla 1-3. 116 Mensajes de estado de la pantalla LCD (continuación) Línea 1 mensaje Línea 2 mensaje Causas Acciones correctivas E0780 PROC # CONFIG ERR Hay un error de configuración en el procesador especificado. Consulte “Solución de problemas de los microprocesadores” en la Guía de instalación y solución de problemas. E0780 PROC # DISABLED El procesador especificado está desactivado. Consulte “Solución de problemas de los microprocesadores” en la Guía de instalación y solución de problemas.
Tabla 1-3. Mensajes de estado de la pantalla LCD (continuación) Línea 1 mensaje Línea 2 mensaje Causas Acciones correctivas E07FA PROC n THERMTRIP La temperatura del microprocesador especificado se encuentra fuera del intervalo de temperaturas aceptable, y se ha interrumpido su funcionamiento. Consulte “Solución de problemas de refrigeración del sistema” en la Guía de instalación y solución de problemas.
Tabla 1-3. Mensajes de estado de la pantalla LCD (continuación) Línea 1 mensaje Línea 2 mensaje Causas Acciones correctivas E0876 PS n AC LOST PS n AC RANGE La fuente de energía para Compruebe si existe corriente la fuente de alimentación alterna para la fuente de especificada no está disponible alimentación especificada. o se encuentra fuera del intervalo aceptable.
Tabla 1-3. Mensajes de estado de la pantalla LCD (continuación) Línea 1 mensaje Línea 2 mensaje EB107 PROC MACHINE CHK El microprocesador o la placa base son defectuosos o se han instalado incorrectamente. EB107 PROC HOT La temperatura del procesador se encuentra fuera del intervalo de temperaturas aceptable, y se ha interrumpido su funcionamiento. Consulte “Solución de problemas de refrigeración del sistema” en la Guía de instalación y solución de problemas.
Tabla 1-3. Mensajes de estado de la pantalla LCD (continuación) Línea 1 mensaje Línea 2 mensaje Causas Acciones correctivas EB113 PCIE NON FATAL ERR Se ha producido un error PCIe que no es grave. Consulte “Solución de problemas de tarjetas de expansión” en la Guía de instalación y solución de problemas. Si el problema persiste, consulte “Obtención de ayuda” en la Guía de instalación y solución de problemas. EB113 CHIPSET ERR Se ha producido un error en el conjunto de chips.
Hojas de datos medioambientales En www.dell.com/environment_datasheets, hallará más información sobre medidas medioambientales relativas a determinadas configuraciones de sistema. Extracción e instalación de la cubierta de refrigeración Para extraer la cubierta de refrigeración, sujete la cubierta por cada extremo y extráigala del sistema hacia arriba.
Información sobre el sistema operativo Linux Inicio de Red Hat Enterprise Linux AS (versión 4) para Intel x86 con más de ocho procesadores lógicos Un sistema que ejecute Red Hat Enterprise Linux AS (versión 4) para el sistema operativo Intel x86 no podrá iniciarse si está configurado con más de ocho procesadores lógicos. Para solucionar este problema, introduzca el parámetro apic=bigsmp en la línea de comandos del kernel al iniciar el sistema.
F3227eb9.fm Page 123 Wednesday, September 6, 2006 3:48 PM Instalación de Microsoft Windows 2000 Los sistemas PowerEdge 6800 con procesadores de doble núcleo con caché L3 no admiten la instalación de Microsoft Windows 2000 Server o Microsoft Windows 2000 Advanced Server. NOTA: los sistemas PowerEdge 6800 con procesadores de un solo núcleo (con o sin caché L3) y procesadores de doble núcleo sólo con caché L2 admiten la instalación de Microsoft Windows 2000 Server o Microsoft Windows 2000 Advanced Server.
124 Actualización de información