Dell EMC Configuration Guide for the S3100 Series 9.13.0.
Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2017 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Contents 1 About this Guide...........................................................................................................................................34 Audience............................................................................................................................................................................34 Conventions.....................................................................................................................................................
Upgrading Dell EMC Networking OS............................................................................................................................ 59 Verify Software Images Before Installation...................................................................................................................59 Using HTTP for File Transfers........................................................................................................................................ 60 4 Management...........
Setting Timeout for EXEC Privilege Mode................................................................................................................... 82 Using Telnet to get to Another Network Device..........................................................................................................83 Lock CONFIGURATION Mode....................................................................................................................................... 83 Viewing the Configuration Lock Status.
Continue Clause........................................................................................................................................................ 115 IP Fragment Handling..................................................................................................................................................... 116 IP Fragments ACL Examples...................................................................................................................................
9 Border Gateway Protocol IPv4 (BGPv4).................................................................................................... 169 Autonomous Systems (AS)........................................................................................................................................... 169 Sessions and Peers......................................................................................................................................................... 171 Establish a Session.......
Changing the WEIGHT Attribute........................................................................................................................... 207 Enabling Multipath................................................................................................................................................... 207 Filtering BGP Routes...............................................................................................................................................
Configure the System to be a DHCP Server..............................................................................................................249 Configuring the Server for Automatic Address Allocation..................................................................................250 Specifying a Default Gateway................................................................................................................................. 251 Configure a Method of Hostname Resolution..............
15 Force10 Resilient Ring Protocol (FRRP)................................................................................................... 276 Protocol Overview......................................................................................................................................................... 276 Ring Status................................................................................................................................................................
18 Internet Group Management Protocol (IGMP)..........................................................................................297 IGMP Implementation Information...............................................................................................................................297 IGMP Protocol Overview.............................................................................................................................................. 297 IGMP Version 2.............................
Enabling a Physical Interface........................................................................................................................................329 Physical Interfaces.........................................................................................................................................................329 Configuration Task List for Physical Interfaces....................................................................................................
Link Bundle Monitoring................................................................................................................................................. 353 Using Ethernet Pause Frames for Flow Control........................................................................................................ 354 Enabling Pause Frames...........................................................................................................................................
UDP Helper..................................................................................................................................................................... 377 Configure UDP Helper............................................................................................................................................. 377 Important Points to Remember..............................................................................................................................
23 iSCSI Optimization...................................................................................................................................403 iSCSI Optimization Overview....................................................................................................................................... 403 Monitoring iSCSI Traffic Flows...............................................................................................................................
LACP Configuration Tasks............................................................................................................................................ 437 Creating a LAG......................................................................................................................................................... 437 Configuring the LAG Interfaces as Dynamic........................................................................................................
LLDP Compatibility.................................................................................................................................................. 472 CONFIGURATION versus INTERFACE Configurations............................................................................................ 472 Enabling LLDP................................................................................................................................................................
Preventing MSDP from Advertising a Local Source................................................................................................. 503 Logging Changes in Peership States...........................................................................................................................504 Terminating a Peership..................................................................................................................................................504 Clearing Peer Statistics......
Track IPv4 and IPv6 Routes................................................................................................................................... 546 Set Tracking Delays................................................................................................................................................. 547 VRRP Object Tracking.............................................................................................................................................
Configuration Task List for Policy-based Routing......................................................................................................594 PBR Exceptions (Permit)....................................................................................................................................... 594 Create a Redirect List.............................................................................................................................................
Suspend Power Delivery on a Port...............................................................................................................................618 Restore Power Delivery on a Port................................................................................................................................ 619 Display the Power Details..............................................................................................................................................
Enabling PVST+ Extend System ID............................................................................................................................. 653 PVST+ Sample Configurations.....................................................................................................................................654 41 Quality of Service (QoS).......................................................................................................................... 657 Implementation Information.......
Configuration Information..............................................................................................................................................691 Configuration Task List............................................................................................................................................ 691 RIP Configuration Example.....................................................................................................................................
TACACS+ Remote Authentication......................................................................................................................... 744 Command Authorization......................................................................................................................................... 745 Protection from TCP Tiny and Overlapping Fragment Attacks............................................................................... 745 Enabling SCP and SSH.................................
Honoring the Incoming DEI Value.......................................................................................................................... 782 Marking Egress Packets with a DEI Value............................................................................................................ 782 Dynamic Mode CoS for VLAN Stacking..................................................................................................................... 783 Mapping C-Tag to S-Tag dot1p Values...........
Copying a Configuration File...................................................................................................................................807 Copying Configuration Files via SNMP.................................................................................................................808 Copying the Startup-Config Files to the Running-Config.................................................................................. 809 Copying the Startup-Config Files to the Server via FTP.
Stack Management Roles....................................................................................................................................... 837 Stack Master Election............................................................................................................................................. 837 Virtual IP....................................................................................................................................................................
STP Root Guard............................................................................................................................................................. 875 Root Guard Scenario............................................................................................................................................... 875 Configuring Root Guard..........................................................................................................................................
UFD and NIC Teaming...................................................................................................................................................904 Important Points to Remember................................................................................................................................... 904 Configuring Uplink Failure Detection...........................................................................................................................
PVST+ Configuration.................................................................................................................................................... 949 Sample PVST+ Configuration.................................................................................................................................949 Peer Routing Configuration Example..........................................................................................................................
Dell-2 VLT Configuration.........................................................................................................................................993 Dell-3 VLT Configuration.........................................................................................................................................994 Dell-4 VLT Configuration........................................................................................................................................
Recognize an Overtemperature Condition..........................................................................................................1042 Troubleshoot an Over-temperature Condition....................................................................................................1043 Recognize an Under-Voltage Condition.............................................................................................................. 1043 Troubleshoot an Under-Voltage Condition.........................
Configuring OSCP responder preference........................................................................................................... 1069 Verifying certificates....................................................................................................................................................1069 Verifying Server certificates..................................................................................................................................
1 About this Guide This guide describes the protocols and features the Dell EMC Networking Operating System (OS) supports and provides configuration instructions and examples for implementing them. For complete information about all the CLI commands, see the Dell EMC Command Line Reference Guide for your system. The S3100 series consists of S3124, S3124F, S3148, S3124P, S3148P platforms. The S3124, S3124F, S3124P, S3148P platforms are available with Dell EMC Networking OS version 9.8(2.0) and later.
2 Configuration Fundamentals The Dell EMC Networking Operating System (OS) command line interface (CLI) is a text-based interface you can use to configure interfaces and protocols. The CLI is largely the same for each platform except for some commands and command outputs. The CLI is structured in modes for security and management purposes. Different sets of commands are available in each mode, and you can limit user access to modes using privilege levels.
You can set user access rights to commands and command modes using privilege levels. For more information about privilege levels and security options, refer to the Privilege Levels Overview section in the Security chapter. The Dell EMC Networking OS CLI is divided into three major mode levels: • EXEC mode is the default mode and has a privilege level of 1, which is the most restricted level.
uBoot PORT-CHANNEL FAILOVER-GROUP PREFIX-LIST PRIORITY-GROUP PROTOCOL GVRP QOS POLICY RSTP ROUTE-MAP ROUTER BGP BGP ADDRESS-FAMILY ROUTER ISIS ISIS ADDRESS-FAMILY ROUTER OSPF ROUTER OSPFV3 ROUTER RIP SPANNING TREE TRACE-LIST VLT DOMAIN VRRP UPLINK STATE GROUP Navigating CLI Modes The Dell EMC Networking OS prompt changes to indicate the CLI mode. The following table lists the CLI mode, its prompt, and information about how to access and exit the CLI mode.
CLI Command Mode Prompt 40 Gigabit Ethernet Interface Access Command interface (INTERFACE modes) Interface Group DellEMC(conf-if-group)# interface(INTERFACE modes) Interface Range DellEMC(conf-if-range)# interface (INTERFACE modes) Loopback Interface DellEMC(conf-if-lo-0)# interface (INTERFACE modes) Management Ethernet Interface DellEMC(conf-if-ma-1/1)# interface (INTERFACE modes) Null Interface DellEMC(conf-if-nu-0)# interface (INTERFACE modes) Port-channel Interface DellEMC(conf-if-po
CLI Command Mode Prompt Access Command ROUTER RIP DellEMC(conf-router_rip)# router rip SPANNING TREE DellEMC(config-span)# protocol spanning-tree 0 TRACE-LIST DellEMC(conf-trace-acl)# ip trace-list CLASS-MAP DellEMC(config-class-map)# class-map CONTROL-PLANE DellEMC(conf-control-cpuqos)# control-plane-cpuqos DHCP DellEMC(config-dhcp)# ip dhcp server DHCP POOL DellEMC(config-dhcp-pool-name)# pool (DHCP Mode) ECMP DellEMC(conf-ecmp-group-ecmpgroup-id)# ecmp-group EIS DellEMC(conf-mg
The do Command You can enter an EXEC mode command from any CONFIGURATION mode (CONFIGURATION, INTERFACE, SPANNING TREE, and so on.) without having to return to EXEC mode by preceding the EXEC mode command with the do command. The following example shows the output of the do command.
Layer 2 protocols are disabled by default. To enable Layer 2 protocols, use the no disable command. For example, in PROTOCOL SPANNING TREE mode, enter no disable to enable Spanning Tree. Obtaining Help Obtain a list of keywords and a brief functional description of those keywords at any CLI mode using the ? or help command: • To list the keywords available in the current mode, enter ? at the prompt or after a keyword. • Enter ? after a command prompt to list all of the available keywords.
Short-Cut Key Combination Action CNTL-N Return to more recent commands in the history buffer after recalling commands with CTRL-P or the UP arrow key. CNTL-P Recalls commands, beginning with the last command. CNTL-R Re-enters the previous command. CNTL-U Deletes the line. CNTL-W Deletes the previous word. CNTL-X Deletes the line. CNTL-Z Ends continuous scrolling of command outputs. Esc B Moves the cursor back one word. Esc F Moves the cursor forward one word.
The except keyword displays text that does not match the specified text. The following example shows this command used in combination with the show system brief command. Example of the except Keyword DellEMC#show system brief | except 1 Stack MAC Reload-Type : 4c:76:25:e5:49:40 : normal-reload [Next boot : normal-reload] The find keyword displays the output of the show command beginning from the first occurrence of specified text.
• On the system that is connected over the console, this message appears: % Warning: User "" on line vty0 "10.11.130.2" is in configuration mode If either of these messages appears, Dell EMC Networking recommends coordinating with the users listed in the message so that you do not unintentionally overwrite each other’s configuration changes.
3 Getting Started This chapter describes how you start configuring your system. When you power up the chassis, the system performs a power-on self test (POST) and system then loads the Dell EMC Networking Operating System. Boot messages scroll up the terminal window during this process. No user interaction is required if the boot process proceeds without interruption. When the boot process completes, the system status LEDs remain online (green) and the console monitor displays the EXEC mode prompt.
Console Access The device has one RJ-45/RS-232 console port, an out-of-band (OOB) Ethernet port, and a micro USB-B console port. Serial Console The RJ-45/RS-232 console port is labeled on the upper right-hand side, as you face the I/O side of the chassis. Figure 1. RJ-45 Console Port 1 RJ-45 console port. Accessing the Console Port To access the console port, follow these steps: For the console port pinout, refer to Accessing the RJ-45 Console Port with a DB-9 Adapter.
Table 2.
• To avoid denial of service (DoS) attacks, a rate-limit of 10 concurrent sessions per minute in SSH is devised. Therefore, you might experience a failure in executing SSH-related scripts when multiple short SSH commands are executed. • If you issue an interactive command in the SSH session, the behavior may not really be interactive.
interface ManagementEthernet slot/port 2 Assign an IP address to the interface. INTERFACE mode ip address ip-address/mask 3 • ip-address: an address in dotted-decimal format (A.B.C.D). • mask: a subnet mask in /prefix-length format (/ xx). Enable the interface. INTERFACE mode no shutdown Configure a Management Route Define a path from the system to the network from which you are accessing the system remotely.
• 8 — input the password that is already encrypted using sha256–based encryption method. • password: Enter the password string for the user. • dynamic-salt: Generates an additional random input to password encryption process whenever the password is configured. • privilege level: Assign a privilege levels to the user. The range is from 0 to 15. • role role-name: Assign a role name for the user.
Copy Files to and from the System The command syntax for copying files is similar to UNIX. The copy command uses the format copy source-file-url destination-file-url. NOTE: For a detailed description of the copy command, refer to the Dell EMC Networking OS Command Reference. • To copy a local file to a remote system, combine the file-origin syntax for a local file location with the file-destination syntax for a remote file location.
Before executing any CLI command to perform file operations, you must first mount the NFS file system to a mount-point on the device. Since multiple mount-points exist on a device, it is mandatory to specify the mount-point to which you want to load the system. The /f10/mnt/nfs directory is the root of all mount-points. To mount an NFS file system, perform the following steps: Table 4.
15 bytes successfully copied DellEMC#copy flash://test/capture.txt.pcap nfsmount:/// Destination file name [test.txt]: ! 15 bytes successfully copied DellEMC#copy flash://test/capture.txt.pcap nfsmount:///username/snoop.pcap ! 24 bytes successfully copied DellEMC# DellEMC#copy tftp://10.16.127.35/username/dv-maa-test ? flash: Copy to local file system ([flash://]filepath) nfsmount: Copy to nfs mount file system (nfsmount:///filepath) running-config remote host: Destination file name [test.
Configure the Overload Bit for a Startup Scenario For information about setting the router overload bit for a specific period of time after a switch reload is implemented, see the Intermediate System to Intermediate System (IS-IS) section in the Dell Command Line Reference Guide for your system. Viewing Files You can only view file information and content on local file systems. To view a list of files or the contents of a file, use the following commands. • View a list of files on the internal flash.
! Version 9.4(0.0) ! Last configuration change at Tue Mar 11 21:33:56 2014 by admin ! Startup-config last updated at Tue Mar 11 12:11:00 2014 by default !
interface TenGigabitEthernet 1/2 no ip address shutdown ! interface TenGigabitEthernet 1/3 no ip address shutdown ! interface TenGigabitEthernet 1/4 no ip address shutdown ! interface TenGigabitEthernet 1/10 no ip address shutdown ! interface TenGigabitEthernet 1/34 ip address 2.1.1.
shutdown ! interface Vlan 5 tagged te 1/1 no ip address shutdown ! interface Vlan 100 no ip address no shutdown ! interface Vlan 1000 ip address 1.1.1.1/16 no shutdown Uncompressed config size – 52 lines write memory compressed The write memory compressed CLI will write the operating configuration to the startup-config file in the compressed mode. In stacking scenario, it will also take care of syncing it to all the standby and member units.
The output of the show file-systems command in the following example shows the total capacity, amount of free memory, file structure, media type, read/write privileges for each storage device in use. DellEMC#show file-systems Size(b) Free(b) Feature Type Flags 520962048 213778432 dosFs2.0 USERFLASH 127772672 21936128 dosFs2.
View Command History The command-history trace feature captures all commands entered by all users of the system with a time stamp and writes these messages to a dedicated trace log buffer. The system generates a trace message for each executed command. No password information is saved to the file. To view the command-history trace, use the show command-history command.
• hash-value: (Optional). Specify the relevant hash published on iSupport.
DellEMC(conf)#ip http vrf {management | } Getting Started 61
4 Management This chapter describes the different protocols or services used to manage the Dell EMC Networking system.
• restricting access to an EXEC mode command • moving commands from EXEC Privilege to EXEC mode • restricting access A user can access all commands at his privilege level and below. Removing a Command from EXEC Mode To remove a command from the list of available commands in EXEC mode for a specific privilege level, use the privilege exec command from CONFIGURATION mode.
• Remove a command from the list of available commands in EXEC mode. CONFIGURATION mode privilege exec level level {command ||...|| command} • Move a command from EXEC Privilege to EXEC mode. CONFIGURATION mode privilege exec level level {command ||...|| command} • Allow access to CONFIGURATION mode. CONFIGURATION mode privilege exec level level configure • Allow access to INTERFACE, LINE, ROUTE-MAP, and/or ROUTER mode. Specify all the keywords in the command.
managementethernet Management Ethernet interface null Null interface port-channel Port-channel interface range Configure interface range sonet SONET interface tengigabitethernet TenGigabit Ethernet interface vlan VLAN interface DellEMC(conf)#interface tengigabitethernet 1/1 DellEMC(conf-if-gi-1/1)#? end Exit from configuration mode exit Exit from interface configuration mode DellEMC(conf-if-gi-1/1)#exit DellEMC(conf)#line ? aux Auxiliary line console Primary terminal line vty Virtual terminal DellEMC(conf)#
• Disable all logging except on the console. CONFIGURATION mode no logging on • Disable logging to the logging buffer. CONFIGURATION mode no logging buffer • Disable logging to terminal lines. CONFIGURATION mode no logging monitor • Disable console logging. CONFIGURATION mode no logging console Audit and Security Logs This section describes how to configure, display, and clear audit and security logs.
• Adding and deleting of users. • User access and configuration changes to the security and crypto parameters (not the key information but the crypto configuration) Important Points to Remember When you enabled RBAC and extended logging: • Only the system administrator user role can execute this command. • The system administrator and system security administrator user roles can view security events and system events.
The following describes the two log messages formats: • 0 – Displays syslog messages format as described in RFC 3164, The BSD syslog Protocol • 1 – Displays syslog message format as described in RFC 5424, The SYSLOG Protocol Example of Configuring the Logging Message Format DellEMC(conf)#logging version ? <0-1> Select syslog version (default = 0) DellEMC(conf)#logging version 1 Display the Logging Buffer and the Logging Configuration To display the current contents of the logging buffer and the logging
Figure 2. Setting Up a Secure Connection to a Syslog Server Pre-requisites To configure a secure connection from the switch to the syslog server: 1 On the switch, enable the SSH server DellEMC(conf)#ip ssh server enable 2 On the syslog server, create a reverse SSH tunnel from the syslog server to the Dell OS switch, using following syntax: ssh -R :: user@remote_host -nNf In the following example the syslog server IP address is 10.156.166.
Sending System Messages to a Syslog Server To send system messages to a specified syslog server, use the following command. The following syslog standards are supported: RFC 5424 The SYSLOG Protocol, R.Gerhards and Adiscon GmbH, March 2009, obsoletes RFC 3164 and RFC 5426 Transmission of Syslog Messages over UDP. • Specify the server to which you want to send system messages. You can configure up to eight syslog servers.
The following example enables login activity tracking and configures the system to store the login activity details for 12 days. DellEMC(config)#login statistics enable DellEMC(config)#login statistics time-period 12 Display Login Statistics To view the login statistics, use the show login statistics command.
Example of the show login statistics user user-id command The show login statistics user user-id command displays the successful and failed login details of a specific user in the last 30 days or the custom defined time period. DellEMC# show login statistics user admin -----------------------------------------------------------------User: admin Last login time: 12:52:01 UTC Tue Mar 22 2016 Last login location: Line vty0 ( 10.16.127.
login concurrent-session limit number-of-sessions Example of Configuring Concurrent Session Limit The following example limits the permitted number of concurrent login sessions to 4. DellEMC(config)#login concurrent-session limit 4 Enabling the System to Clear Existing Sessions To enable the system to clear existing login sessions, follow this procedure: • Use the following command.
Enabling Secured CLI Mode The secured CLI mode prevents the users from enhancing the permissions or promoting the privilege levels. • Enter the following command to enable the secured CLI mode: CONFIGURATION Mode secure-cli enable After entering the command, save the running-configuration. Once you save the running-configuration, the secured CLI mode is enabled. If you do not want to enter the secured mode, do not save the running-configuration.
Sending System Messages to a Syslog Server To send system messages to a specified syslog server, use the following command. The following syslog standards are supported: RFC 5424 The SYSLOG Protocol, R.Gerhards and Adiscon GmbH, March 2009, obsoletes RFC 3164 and RFC 5426 Transmission of Syslog Messages over UDP. • Specify the server to which you want to send system messages. You can configure up to eight syslog servers.
logging buffered size • NOTE: When you decrease the buffer size, Dell EMC Networking OS deletes all messages stored in the buffer. Increasing the buffer size does not affect messages in the buffer. Specify the number of messages that Dell EMC Networking OS saves to its logging history table.
logging facility [facility-type] • auth (for authorization messages) • cron (for system scheduler messages) • daemon (for system daemons) • kern (for kernel messages) • local0 (for local use) • local1 (for local use) • local2 (for local use) • local3 (for local use) • local4 (for local use) • local5 (for local use) • local6 (for local use) • local7 (for local use) • lpr (for line printer system messages) • mail (for mail system messages) • news (for USENET news messages) • sys
Configure the following parameters for the virtual terminal lines: • number: the range is from zero (0) to 8. • end-number: the range is from 1 to 8. You can configure multiple virtual terminals at one time by entering a number and an end-number. 2 Configure a level and set the maximum number of messages to print. LINE mode logging synchronous [level severity-level | all] [limit] Configure the following optional parameters: • level severity-level: the range is from 0 to 7. The default is 2.
Configuration Task List for File Transfer Services The configuration tasks for file transfer services are: • Enable FTP Server (mandatory) • Configure FTP Server Parameters (optional) • Configure FTP Client Parameters (optional) Enabling the FTP Server To enable the system as an FTP server, use the following command. To view FTP configuration, use the show running-config ftp command in EXEC privilege mode. • Enable FTP on the system.
Configuring FTP Client Parameters To configure FTP client parameters, use the following commands. • Enter the following keywords and the interface information: • For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
access-class access-list-name [ipv4 | ipv6] NOTE: If you already have configured generic IP ACL on a terminal line, then you cannot further apply IPv4 or IPv6 specific filtering on top of this configuration. Similarly, if you have configured either IPv4 or IPv6 specific filtering on a terminal line, you cannot apply generic IP ACL on top of this configuration.
tacacs+ 1 Prompt for a username and password and use a TACACS+ server to authenticate. Configure an authentication method list. You may use a mnemonic name or use the keyword default. The default authentication method for terminal lines is local and the default method list is empty. CONFIGURATION mode aaa authentication login {method-list-name | default} [method-1] [method-2] [method-3] [method-4] [method-5] [method-6] 2 Apply the method list from Step 1 to a terminal line.
line console 0 exec-timeout 0 0 DellEMC(config-line-console)# Using Telnet to get to Another Network Device To telnet to another device, use the following commands. NOTE: The device allows 120 Telnet sessions per minute, allowing the login and logout of 10 Telnet sessions, 12 times in a minute. If the system reaches this non-practical limit, the Telnet service is stopped for 10 minutes. You can use console and SSH service to access the system during downtime.
You can then send any user a message using the send command from EXEC Privilege mode. Alternatively, you can clear any line using the clear command from EXEC Privilege mode. If you clear a console session, the user is returned to EXEC mode. Example of Locking CONFIGURATION Mode for Single-User Access DellEMC(conf)#configuration mode exclusive auto BATMAN(conf)#exit 3d23h35m: %RPM0-P:CP %SYS-5-CONFIG_I: Configured from console by console DellEMC#config ! Locks configuration mode exclusively.
5 802.1X 802.1X is a port-based Network Access Control (PNAC) that provides an authentication mechanism to devices wishing to attach to a LAN or WLAN. A device connected to a port that is enabled with 802.1X is disallowed from sending or receiving packets on the network until its identity is verified (through a username and password, for example). 802.
Figure 4. EAP Frames Encapsulated in Ethernet and RADUIS The authentication process involves three devices: • The device attempting to access the network is the supplicant. The supplicant is not allowed to communicate on the network until the authenticator authorizes the port. It can only communicate with the authenticator in response to 802.1X requests. • The device with which the supplicant communicates is the authenticator. The authenticator is the gate keeper of the network.
• Configuring Timeouts • Configuring Dynamic VLAN Assignment with Port Authentication • Guest and Authentication-Fail VLANs Port-Authentication Process The authentication process begins when the authenticator senses that a link status has changed from down to up: 1 When the authenticator senses a link state change, it requests that the supplicant identify itself using an EAP Identity Request frame. 2 The supplicant responds with its identity in an EAP Response Identity frame.
Figure 6. EAP Over RADIUS RADIUS Attributes for 802.1X Support Dell EMC Networking systems include the following RADIUS attributes in all 802.1X-triggered Access-Request messages: Attribute 31 Calling-station-id: relays the supplicant MAC address to the authentication server. Attribute 41 NAS-Port-Type: NAS-port physical port type. 15 indicates Ethernet. Attribute 61 NAS-Port: the physical port number by which the authenticator is connected to the supplicant.
Enabling 802.1X Enable 802.1X globally. Figure 7. 802.1X Enabled 1 Enable 802.1X globally. CONFIGURATION mode dot1x authentication 2 Enter INTERFACE mode on an interface or a range of interfaces. INTERFACE mode interface [range] 3 Enable 802.1X on the supplicant interface only. INTERFACE mode dot1x authentication Examples of Verifying that 802.1X is Enabled Globally and on an Interface Verify that 802.
In the following example, the bold lines show that 802.1X is enabled. DellEMC#show running-config | find dot1x dot1x authentication ! [output omitted] ! interface GigabitEthernet 2/1 no ip address dot1x authentication no shutdown ! DellEMC# To view 802.1X configuration information for an interface, use the show dot1x interface command. In the following example, the bold lines show that 802.1X is enabled on all ports unauthorized by default. DellEMC#show dot1x interface GigabitEthernet 2/1/ 802.
802.1x profile information ----------------------------Dot1x Profile test Profile MACs 00:00:00:00:01:11 Configuring MAC addresses for a do1x Profile To configure a list of MAC addresses for a dot1x profile, use the mac command. You can configure 1 to 6 MAC addresses. • Configure a list of MAC addresses for a dot1x profile. DOT1X PROFILE CONFIG (conf-dot1x-profile) mac mac-address mac-address — Enter the keyword mac and type up to the 48– bit MAC addresses using the nn:nn:nn:nn:nn:nn format.
Untagged VLAN id: Guest VLAN: Guest VLAN id: Auth-Fail VLAN: Auth-Fail VLAN id: Auth-Fail Max-Attempts:3 Critical VLAN: Critical VLAN id: Mac-Auth-Bypass Only: Static-MAB: Static-MAB Profile: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Auth Type: Auth PAE State: Backend State: None Enable 100 Enable 200 Enable 300 Disable Enable Sample 90 seconds 120 seconds 10 30 seconds 30 seconds 7200 seconds 10 SINGLE_HOST Authenticated Idle Configuring Criti
Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Host Mode: Auth PAE State: Backend State: 30 seconds 30 seconds 3600 seconds 2 SINGLE_HOST Authenticated Idle Configuring Request Identity Re-Transmissions When the authenticator sends a Request Identity frame and the supplicant does not respond, the authenticator waits for 30 seconds and then re-transmits the frame.
Example of Configuring and Verifying Port Authentication The following example shows configuration information for a port for which the authenticator re-transmits an EAP Request Identity frame: • after 90 seconds and a maximum of 10 times for an unresponsive supplicant • re-transmits an EAP Request Identity frame The bold lines show the new re-transmit interval, new quiet period, and new maximum re-transmissions.
Port Control: Port Auth Status: Re-Authentication: Untagged VLAN id: Tx Period: Quiet Period: ReAuth Max: Supplicant Timeout: Server Timeout: Re-Auth Interval: Max-EAP-Req: Auth Type: Auth PAE State: Backend State: Auth PAE State: Backend State: FORCE_AUTHORIZED UNAUTHORIZED Disable None 90 seconds 120 seconds 2 30 seconds 30 seconds 3600 seconds 10 SINGLE_HOST Initialize Initialize Initialize Initialize Re-Authenticating a Port You can configure the authenticator for periodic re-authentication.
Auth Type: Auth PAE State: Backend State: Auth PAE State: Backend State: SINGLE_HOST Initialize Initialize Initialize Initialize Configuring Timeouts If the supplicant or the authentication server is unresponsive, the authenticator terminates the authentication process after 30 seconds by default. You can configure the amount of time the authenticator waits for a response.
Configuring Dynamic VLAN Assignment with Port Authentication Dell EMC Networking OS supports dynamic VLAN assignment when using 802.1X. The basis for VLAN assignment is RADIUS attribute 81, Tunnel-Private-Group-ID.
5 Verify that the port has been authorized and placed in the desired VLAN (refer to the illustration in Dynamic VLAN Assignment with Port Authentication). Guest and Authentication-Fail VLANs Typically, the authenticator (the Dell system) denies the supplicant access to the network until the supplicant is authenticated.
Configure a port to be placed in the VLAN after failing the authentication process as specified number of times using the dot1x authfail-vlan command from INTERFACE mode. Configure the maximum number of authentication attempts by the authenticator using the keyword max-attempts with this command.
6 Access Control List (ACL) VLAN Groups and Content Addressable Memory (CAM) This section describes the access control list (ACL) virtual local area network (VLAN) group, and content addressable memory (CAM) enhancements. Optimizing CAM Utilization During the Attachment of ACLs to VLANs To minimize the number of entries in CAM, enable and configure the ACL CAM feature. Use this feature when you apply ACLs to a VLAN (or a set of VLANs) and when you apply ACLs to a set of ports.
• The ACL VLAN group is deleted and it does not contain VLAN members. • The ACL is applied or removed from a group and the ACL group does not contain a VLAN member. • The description of the ACL group is added or removed. Guidelines for Configuring ACL VLAN Groups Keep the following points in mind when you configure ACL VLAN groups: • The interfaces where you apply the ACL VLAN group function as restricted interfaces.
description description 3 Apply an egress IP ACL to the ACL VLAN group. CONFIGURATION (conf-acl-vl-grp) mode ip access-group {group name} out implicit-permit 4 Add VLAN member(s) to an ACL VLAN group. CONFIGURATION (conf-acl-vl-grp) mode member vlan {VLAN-range} 5 Display all the ACL VLAN groups or display a specific ACL VLAN group, identified by name.
EXEC Privilege mode DellEMC#show cam-usage switch Stackunit|Portpipe| CAM Partition | Total CAM | Used CAM |Available CAM ========|========|=================|============|============|============= 1 | 0 | IN-L2 ACL | 1536 | 0 | 1536 | | OUT-L2 ACL | 206 | 9 | 197 Codes: * - cam usage is above 90%. Viewing CAM Usage View the amount of CAM space available, used, and remaining in each partition (including IPv4Flow and Layer 2 ACL sub- partitions) using the show cam-usage command in EXEC Privilege mode.
2 | 0 | IN-L2 ACL | | IN-L3 ACL | | IN-V6 ACL | | OUT-L2 ACL | | OUT-L3 ACL | | OUT-V6 ACL 3 | 0 | IN-L2 ACL | | IN-L3 ACL | | IN-V6 ACL | | OUT-L2 ACL | | OUT-L3 ACL | | OUT-V6 ACL Codes: * - cam usage is above 90%.
To reset the number of FP blocks to the default, use the no version of these commands. By default, zero groups are allocated for the ACL in VCAP. ACL VLAN groups or CAM optimization is not enabled by default. You must also allocate the slices for CAM optimization. To display the number of FP blocks that is allocated for the different VLAN services, use the show cam-acl-vlan command. After you configure the ACL VLAN groups, reboot the system to store the settings in nonvolatile storage.
7 Access Control Lists (ACLs) This chapter describes access control lists (ACLs), prefix lists, and route-maps. At their simplest, access control lists (ACLs), prefix lists, and route-maps permit or deny traffic based on MAC and/or IP addresses. This chapter describes implementing IP ACLs, IP prefix lists and route-maps. For MAC ACLS, refer to Layer 2.
Topics: • IP Access Control Lists (ACLs) • Important Points to Remember • IP Fragment Handling • Configure a Standard IP ACL • Configure an Extended IP ACL • Configure Layer 2 and Layer 3 ACLs • Assign an IP ACL to an Interface • Applying an IP ACL • Configure Ingress ACLs • Configure Egress ACLs • IP Prefix Lists • ACL Resequencing • Route Maps • Logging of ACL Processes • Flow-Based Monitoring IP Access Control Lists (ACLs) In Dell EMC Networking switch/routers, you can creat
CAM Usage The following section describes CAM allocation and CAM optimization. • User Configurable CAM Allocation • CAM Optimization User Configurable CAM Allocation Allocate space for IPV6 ACLs by using the cam-acl command in CONFIGURATION mode. The CAM space is allotted in filter processor (FP) blocks. The total space allocated must equal 13 FP blocks. (There are 16 FP blocks, but System Flow requires three blocks that cannot be reallocated.
If counters are enabled on ACL rules that are already configured, those counters are reset when a new rule which is inserted or prepended or appended requires a hardware shift in the flow table. Resetting the counters to 0 is transient as the proginal counter values are retained after a few seconds. If there is no need to shift the flow in the hardware, the counters are not affected.
DellEMC(conf-class-map)#match ip access-group acl2 DellEMC(conf-class-map)#exit DellEMC(conf)#policy-map-input pmap DellEMC(conf-policy-map-in)#service-queue 7 class-map cmap1 DellEMC(conf-policy-map-in)#service-queue 4 class-map cmap2 DellEMC(conf-policy-map-in)#exit DellEMC(conf)#interface gigabitethernet 10/1 DellEMC(conf-if-gi-10/1)#service-policy input pmap Important Points to Remember • For route-maps with more than one match clause: • Two or more match clauses within the same route-map sequence ha
To view the configuration, use the show config command in ROUTE-MAP mode. DellEMC(config-route-map)#show config ! route-map dilling permit 10 DellEMC(config-route-map)# You can create multiple instances of this route map by using the sequence number option to place the route maps in the correct order. Dell EMC Networking OS processes the route maps with the lowest sequence number first.
does a match ONLY if there is a match among ALL the match commands. In the following example, there is a match if a route has any of the tag values specified in the match commands. Example of the match Command to Match Any of Several Values The following example shows using the match command to match any of several values.
• • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Match destination routes specified in a prefix list (IPv4). CONFIG-ROUTE-MAP mode match ip address prefix-list-name • Match destination routes specified in a prefix list (IPv6).
set as-path prepend as-number [... as-number] • Generate a tag to be added to redistributed routes. CONFIG-ROUTE-MAP mode set automatic-tag • Specify an OSPF area or ISIS level for redistributed routes. CONFIG-ROUTE-MAP mode set level {backbone | level-1 | level-1-2 | level-2 | stub-area} • Specify a value for the BGP route’s LOCAL_PREF attribute. CONFIG-ROUTE-MAP mode set local-preference value • Specify a value for redistributed routes.
redistribute command in OSPF, RIP, ISIS, and BGP to set some of these attributes for routes that are redistributed into those protocols. Route maps add to that redistribution capability by allowing you to match specific routes and set or change more attributes when redistributing those routes. In the following example, the redistribute command calls the route map static ospf to redistribute only certain static routes into OSPF.
set as-path prepend 1 2 3 4 5 continue 30! IP Fragment Handling Dell EMC Networking OS supports a configurable option to explicitly deny IP fragmented packets, particularly second and subsequent packets. It extends the existing ACL command syntax with the fragments keyword for all Layer 3 rules applicable to all Layer protocols (permit/ deny ip/tcp/udp/icmp). • Both standard and extended ACLs support IP fragments.
• If a packet's FO > 0, the packet is denied. • If a packet's FO = 0, the next ACL line is processed. Example of Permitting All Packets from a Specified Host In this first example, TCP packets from host 10.1.1.1 with TCP destination port equal to 24 are permitted. All others are denied. DellEMC(conf)#ip access-list extended ABC DellEMC(conf-ext-nacl)#permit tcp host 10.1.1.
To view the rules of a particular ACL configured on a particular interface, use the show ip accounting access-list ACL-name interface interface command in EXEC Privilege mode. Example of Viewing the Rules of a Specific ACL on an Interface The following is an example of viewing the rules of a specific ACL on an interface. DellEMC#show ip accounting access-list ToOspf interface gig 1/6 Standard IP access list ToOspf seq 5 deny any seq 10 deny 10.2.0.0 /16 seq 15 deny 10.3.0.0 /16 seq 20 deny 10.4.0.
! ip access-list standard acl1 seq 5 permit 10.1.0.0/16 monitor 177 DellEMC(config-std-nacl)# To view all configured IP ACLs, use the show ip accounting access-list command in EXEC Privilege mode. The following examples shows how to view a standard ACL filter sequence for an interface.
ip access-list extended access-list-name 2 Configure an extended IP ACL filter for TCP packets. CONFIG-EXT-NACL mode seq sequence-number {deny | permit} tcp {source mask | any | host ip-address} [count [byte]] [order] [monitor [session-id]] [fragments] Configure Filters, UDP Packets To create a filter for UDP packets with a specified sequence number, use the following commands. 1 Create an extended IP ACL and assign it a unique name.
{deny | permit} tcp {source mask] | any | host ip-address}} [count [byte]] [order] [monitor [session-id]] [fragments] • Configure a deny or permit filter to examine UDP packets. CONFIG-EXT-NACL mode {deny | permit} udp {source mask | any | host ip-address}} [count [byte]] [order] [monitor [session-id]] [fragments] When you use the log keyword, the CP logs details about the packets that match.
For information about MAC ACLs, refer to Layer 2. Assign an IP ACL to an Interface To pass traffic through a configured IP ACL, assign that ACL to a physical interface, a port channel interface, or a VLAN. The IP ACL is applied to all traffic entering a physical or port channel interface and the traffic is either forwarded or dropped depending on the criteria and actions specified in the ACL. The same ACL may be applied to different interfaces and that changes its functionality.
Counting ACL Hits You can view the number of packets matching the ACL by using the count option when creating ACL entries. 1 Create an ACL that uses rules with the count option. Refer to Configure a Standard IP ACL Filter. 2 Apply the ACL as an inbound or outbound ACL on an interface. 3 show ip accounting access-list EXEC Privilege mode View the number of packets matching the ACL. Configure Ingress ACLs Ingress ACLs are applied to interfaces and to traffic entering the system.
To create an egress ACL, use the ip access-group command in EXEC Privilege mode. The example shows viewing the configuration, applying rules to the newly created access group, and viewing the access list. NOTE: VRF based ACL configurations are not supported on the egress traffic. Example of Applying ACL Rules to Egress Traffic and Viewing ACL Configuration To specify ingress, use the out keyword. Begin applying rules to the ACL with the ip access-list extended abcd command.
CONFIGURATION mode ipv6 control-plane [egress filter] 3 Create a Layer 3 ACL using permit rules with the count option to describe the desired CPU traffic. CONFIG-NACL mode permit ip {source mask | any | host ip-address} {destination mask | any | host ip-address} count [monitor [session-id]] Dell EMC Networking OS Behavior: Virtual router redundancy protocol (VRRP) hellos and internet group management protocol (IGMP) packets are not affected when you enable egress ACL filtering for CPU traffic.
• Configuring a prefix list • Use a prefix list for route redistribution For a complete listing of all commands related to prefix lists, refer to the Dell EMC Networking OS Command Line Interface Reference Guide. Creating a Prefix List To create a prefix list, use the following commands. 1 Create a prefix list and assign it a unique name. You are in PREFIX LIST mode. CONFIGURATION mode ip prefix-list prefix-name 2 Create a prefix list with a sequence number and a deny or permit action.
ip prefix-list prefix-name 2 Create a prefix list filter with a deny or permit action. CONFIG-NPREFIXL mode {deny | permit} ip-prefix [ge min-prefix-length] [le max-prefix-length] The optional parameters are: • • ge min-prefix-length: is the minimum prefix length to be matched (0 to 32). le max-prefix-length: is the maximum prefix length to be matched (0 to 32).
Prefix-list with the last deletion/insertion: filter_ospf ip prefix-list filter_in: count: 3, range entries: 3, sequences: 5 - 10 ip prefix-list filter_ospf: count: 4, range entries: 1, sequences: 5 - 10 DellEMC> Applying a Prefix List for Route Redistribution To pass traffic through a configured prefix list, use the prefix list in a route redistribution command. Apply the prefix list to all traffic redistributed into the routing process.
If you enter the name of a non-existent prefix list, all routes are forwarded. CONFIG-ROUTER-OSPF mode distribute-list prefix-list-name out [connected | rip | static] Example of Viewing Configured Prefix Lists (ROUTER OSPF mode) To view the configuration, use the show config command in ROUTER OSPF mode, or the show running-config ospf command in EXEC mode. DellEMC(conf-router_ospf)#show config ! router ospf 34 network 10.2.1.1 255.255.255.255 area 0.0.0.
resequence access-list {ipv4 | ipv6 | mac} {access-list-name StartingSeqNum Step-to-Increment} • IPv4 or IPv6 prefix-list EXEC mode resequence prefix-list {ipv4 | ipv6} {prefix-list-name StartingSeqNum Step-to-Increment} Examples of Resequencing ACLs When Remarks and Rules Have the Same Number or Different Numbers Remarks and rules that originally have the same sequence number have the same sequence number after you apply the resequence command.
Route Maps Although route maps are similar to ACLs and prefix lists in that they consist of a series of commands that contain a matching criterion and an action, route maps can modify parameters in matching packets. Implementation Information ACLs and prefix lists can only drop or forward the packet or traffic. Route maps process routes for route redistribution. For example, a route map can be called to filter only specific routes and to add a metric. Route maps also have an “implicit deny.
• For IP packets that contain the transport layer protocol as Transmission Control Protocol (TCP) or User Datagram Protocol (UDP), the ACL name, sequence number, ACL action (permit or deny), source and destination MAC addresses, source and destination IP addresses, and the source and destination ports (Layer 4 parameters) are also recorded. If the packet contains an unidentified EtherType or transport layer protocol, the values for these parameters are saved as Unknown in the log message.
CONFIG-STD-NACL mode seq sequence-number {deny | permit} {source [mask] | any | host ip-address} [log [thresholdin-msgs count] ] 2 Specify the interval in minutes at which ACL logs must be generated. You can enter an interval in the range of 1-10 minutes. The default frequency at which ACL logs are generated is 5 minutes. If ACL logging is stopped because the configured threshold has exceeded, it is re-enabled after the logging interval period elapses.
monitored interface. Flow monitoring is supported for standard and extended IPv4 ACLs, standard and extended IPv6 ACLs, and standard and extended MAC ACLs. CONFIG-STD-NACL mode seq sequence-number {deny | permit} {source [mask] | any | host ip-address} [count [byte]] [order] [fragments] [log [threshold-in-msgs count]] [monitor] If you configure the flow-based enable command and do not apply an ACL on the source port or the monitored port, both flow-based monitoring and port mirroring do not function.
Enabling Flow-Based Monitoring Flow-based monitoring is supported on the platform. Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead of all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 2 and Layer 3 ingress and egress traffic. You can specify traffic using standard or extended access-lists. 1 Enable flow-based monitoring for a monitoring session.
0 N/A 136 Gi 1/1 yes Gi 1/2 Access Control Lists (ACLs) rx Flow N/A N/A 0 0 No N/A
8 Bidirectional Forwarding Detection (BFD) BFD is a protocol that is used to rapidly detect communication failures between two adjacent systems. It is a simple and lightweight replacement for existing routing protocol link state detection mechanisms. It also provides a failure detection solution for links on which no routing protocol is used. BFD is a simple hello mechanism. Two neighboring systems running BFD establish a session using a three-way handshake.
BFD Packet Format Control packets are encapsulated in user datagram protocol (UDP) packets. The following illustration shows the complete encapsulation of a BFD control packet inside an IPv4 packet. Figure 9. BFD in IPv4 Packet Format Field Description Diagnostic Code The reason that the last session failed. State The current local session state. Refer to BFD Sessions. Flag A bit that indicates packet function.
Field Description Detection Multiplier The number of packets that must be missed in order to declare a session down. Length The entire length of the BFD packet. My Discriminator A random number generated by the local system to identify the session. Your Discriminator A random number generated by the remote system to identify the session. Discriminator values are necessary to identify the session to which a control packet belongs because there can be many sessions running on a single interface.
Demand mode If one system requests Demand mode, the other system stops sending periodic control packets; it only sends a response to status inquiries from the Demand mode initiator. Either system (but not both) can request Demand mode at any time. NOTE: Dell EMC Networking OS supports Asynchronous mode only. A session can have four states: Administratively Down, Down, Init, and Up. State Description Administratively Down The local system does not participate in a particular session.
Figure 10.
Session State Changes The following illustration shows how the session state on a system changes based on the status notification it receives from the remote system. For example, if a session on a system is down and it receives a Down status notification from the remote system, the session state on the local system changes to Init. Figure 11.
• Configure BFD for OSPF • Configure BFD for OSPFv3 • Configure BFD for IS-IS • Configure BFD for BGP • Configure BFD for VRRP • Configuring Protocol Liveness Configure BFD for Physical Ports Configuring BFD for physical ports is supported on the C-Series and E-Series platforms only. BFD on physical ports is useful when you do not enable the routing protocol.
Example of Viewing Session Parameters R1(conf-if-gi-4/24)#bfd interval 100 min_rx 100 multiplier 4 role passive R1(conf-if-gi-4/24)#do show bfd neighbors detail Session Discriminator: 1 Neighbor Discriminator: 1 Local Addr: 2.2.2.1 Local MAC Addr: 00:01:e8:09:c3:e5 Remote Addr: 2.2.2.
Configuring BFD for static routes is a three-step process: 1 Enable BFD globally. 2 Configure static routes on both routers on the system (either local or remote). 3 Configure an IP route to connect BFD on the static routes using the ip route bfd command.
Establishing Static Route Sessions on Specific Neighbors You can selectively enable BFD sessions on specific neighbors based on a destination prefix-list. When you establish a BFD session using the ip route bfd command, all the next-hop neighbors in the static route become part of the BFD session. Starting with Dell EMC Networking OS release 9.11.0.0, you can enable BFD sessions on specific next-hop neighbors.
CONFIGURATION mode ip route bfd [prefix-list prefix-list-name] interval milliseconds min_rx milliseconds multiplier value role [active | passive] To view session parameters, use the show bfd neighbors detail command. Disabling BFD for Static Routes If you disable BFD, all static route BFD sessions are torn down. A final Admin Down packet is sent to all neighbors on the remote systems, and those neighbors change to the Down state. To disable BFD for static routes, use the following command.
Establishing Sessions with OSPF Neighbors for the Default VRF BFD sessions can be established with all OSPF neighbors at once or sessions can be established with all neighbors out of a specific interface. Sessions are only established when the OSPF adjacency is in the Full state. Figure 13. Establishing Sessions with OSPF Neighbors To establish BFD with all OSPF neighbors or with OSPF neighbors on a single interface, use the following commands. • Enable BFD globally.
INTERFACE mode ip ospf bfd all-neighbors Example of Verifying Sessions with OSPF Neighbors To view the established sessions, use the show bfd neighbors command. The bold line shows the OSPF BFD sessions. R2(conf-router_ospf)#bfd all-neighbors R2(conf-router_ospf)#do show bfd neighbors * - Active session role Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr * 2.2.2.2 * 2.2.3.1 RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.2.1 Gi 2/1 Up 100 100 3 O 2.2.3.
B C I O O3 R - BGP CLI ISIS OSPF OSPFv3 Static Route (RTM) LocalAddr * 10.1.3.2 RemoteAddr 10.1.3.1 Interface State Rx-int Tx-int Mult Clients Gi 1/3 Up 300 250 3 C DellEMC# show bfd neighbors detail Session Discriminator: 1 Neighbor Discriminator: 1 Local Addr: 10.1.3.2 Local MAC Addr: 00:01:e8:02:15:0e Remote Addr: 10.1.3.
Disabling BFD for OSPF If you disable BFD globally, all sessions are torn down and sessions on the remote system are placed in a Down state. If you disable BFD on an interface, sessions on the interface are torn down and sessions on the remote system are placed in a Down state. Disabling BFD does not trigger a change in BFD clients; a final Admin Down packet is sent before the session is terminated. To disable BFD sessions, use the following commands. • Disable BFD sessions with all OSPF neighbors.
C I O O3 R M V VT - CLI ISIS OSPF OSPFv3 Static Route (RTM) MPLS VRRP Vxlan Tunnel LocalAddr * 1.1.1.1 RemoteAddr 1.1.1.2 Interface Gi 1/1 State Rx-int Tx-int Mult Clients Up 200 200 3 O * 2.1.1.1 2.1.1.
R M V VT - Static Route (RTM) MPLS VRRP Vxlan Tunnel LocalAddr Clients * 10.1.1.1 511 O RemoteAddr Interface State Rx-int Tx-int Mult VRF 10.1.1.2 Vl 100 Up 150 150 3 * 11.1.1.1 511 O 11.1.1.2 Vl 101 Up 150 150 3 * 12.1.1.1 511 O 12.1.1.2 Vl 102 Up 150 150 3 * 13.1.1.1 511 O 13.1.1.
To disable BFD sessions, use the following commands. • Disable BFD sessions with all OSPFv3 neighbors. ROUTER-OSPFv3 mode no bfd all-neighbors • Disable BFD sessions with OSPFv3 neighbors on a single interface. INTERFACE mode ipv6 ospf bfd all-neighbors disable Configure BFD for IS-IS When using BFD with IS-IS, the IS-IS protocol registers with the BFD manager on the RPM. BFD sessions are then established with all neighboring interfaces participating in IS-IS.
Establishing Sessions with IS-IS Neighbors BFD sessions can be established for all IS-IS neighbors at once or sessions can be established for all neighbors out of a specific interface. Figure 14. Establishing Sessions with IS-IS Neighbors To establish BFD with all IS-IS neighbors or with IS-IS neighbors on a single interface, use the following commands. • Establish sessions with all IS-IS neighbors. ROUTER-ISIS mode • bfd all-neighbors Establish sessions with IS-IS neighbors on a single interface.
Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) LocalAddr * 2.2.2.2 RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.2.1 Gi 2/1 Up 100 100 3 I Changing IS-IS Session Parameters BFD sessions are configured with default intervals and a default role. The parameters that you can configure are: Desired TX Interval, Required Min RX Interval, Detection Multiplier, and system role. These parameters are configured for all IS-IS sessions or all IS-IS sessions out of an interface.
Prerequisites Before configuring BFD for BGP, you must first configure the following settings: 1 Configure BGP on the routers that you want to interconnect. 2 Enable fast fall-over for BGP neighbors to reduce convergence time (the neighbor fall-over command)s. Establishing Sessions with BGP Neighbors Before configuring BFD for BGP, you must first configure BGP on the routers that you want to interconnect.
BFD for BGP is supported only on directly-connected BGP neighbors and only in BGP IPv4 networks. As long as each BFD for BGP neighbor receives a BFD control packet within the configured BFD interval for failure detection, the BFD session remains up and BGP maintains its adjacencies. If a BFD for BGP neighbor does not receive a control packet within the detection interval, the router informs any clients of the BFD session (other routing protocols) about the failure.
bfd enable 2 Specify the AS number and enter ROUTER BGP configuration mode. CONFIGURATION mode router bgp as-number 3 Add a BGP neighbor or peer group in a remote AS. CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group name} remote-as as-number 4 Enable the BGP neighbor. CONFIG-ROUTERBGP mode neighbor {ip-address | peer-group-name} no shutdown 5 Add a BGP neighbor or peer group in a remote AS.
Establishing Sessions with BGP Neighbors for Nondefault VRF To establish sessions with either IPv6 or IPv4 BGP neighbors for nondefault VRFs, follow these steps: 1 Enable BFD globally. CONFIGURATION mode bfd enable 2 Specify the AS number and enter ROUTER BGP configuration mode. CONFIGURATION mode router bgp as-number 3 Specify the address family as IPv4. CONFIG-ROUTERBGP mode address-family ipv4 vrf vrf-name 4 Add an IPv4 BGP neighbor or peer group in a remote AS.
DellEMC(conf-router_bgp_af)#address-family ipv6 unicast vrf vrf1 DellEMC(conf-router_bgpv6_af)#neighbor 20::2 activate DellEMC(conf-router_bgpv6_af)#address-family ipv4 vrf vrf1 DellEMC(conf-router_bgp_af)#bfd all-neighbors DellEMC(conf-router_bgp_af)#exit DellEMC(conf-router_bgp)#show config ! router bgp 1 ! address-family ipv4 vrf vrf1 neighbor 10.1.1.2 remote-as 2 neighbor 10.1.1.
If you explicitly enable (or disable) a peer group for BFD that has no BFD parameters configured (for example, advertisement interval) using the neighbor peer-group-name bfd command, the peer group inherits any BFD settings configured with the bfd allneighbors command. Displaying BFD for BGP Information You can display related information for BFD for BGP. To display information about BFD for BGP sessions on a router, use the following commands and refer to the following examples.
M V - MPLS - VRRP LocalAddr * 1.1.1.3 * 2.2.2.3 * 3.3.3.3 RemoteAddr 1.1.1.2 2.2.2.2 3.3.3.2 Interface Te 6/0 Te 6/1 Te 6/2 State Up Up Up Rx-int 200 200 200 Tx-int 200 200 200 Mult 3 3 3 Clients B B B The bold lines show the BFD session parameters: TX (packet transmission), RX (packet reception), and multiplier (maximum number of missed packets). R2# show bfd neighbors detail Session Discriminator: 9 Neighbor Discriminator: 10 Local Addr: 1.1.1.3 Local MAC Addr: 00:01:e8:66:da:33 Remote Addr: 1.
Registration De-registration Init Up Down Admin Down : : : : : : 5 4 0 6 0 2 Interface TenGigabitEthernet 6/1 Protocol BGP Messages: Registration De-registration Init Up Down Admin Down : : : : : : 5 4 0 6 0 2 Interface TenGigabitEthernet 6/2 Protocol BGP Messages: Registration De-registration Init Up Down Admin Down : : : : : : 1 0 0 1 0 2 The bold line shows the message displayed when you enable BFD for BGP connections. R2# show ip bgp summary BGP router identifier 10.0.0.
ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Neighbor is using BGP global mode BFD configuration For address family: IPv4 Unicast BGP table version 0, neighbor version 0 Prefixes accepted 0 (consume 0 bytes), withdrawn 0 by peer, martian prefixes ignored 0 Prefixes advertised 0, denied 0, withdrawn 0 from peer Connections established 1; dropped 0 Last reset never Local host: 2.2.2.
Establishing Sessions with All VRRP Neighbors BFD sessions can be established for all VRRP neighbors at once, or a session can be established with a particular neighbor. Figure 16. Establishing Sessions with All VRRP Neighbors To establish sessions with all VRRP neighbors, use the following command. • Establish sessions with all VRRP neighbors.
The bold line shows that VRRP BFD sessions are enabled. DellEMC(conf-if-gi-4/25)#vrrp bfd all-neighbors DellEMC(conf-if-gi-4/25)#do show bfd neighbor * - Active session role Ad Dn - Admin Down C - CLI I - ISIS O - OSPF R - Static Route (RTM) V - VRRP LocalAddr * 2.2.5.1 RemoteAddr Interface State Rx-int Tx-int Mult Clients 2.2.5.2 Gi 4/25 Down 1000 1000 3 V To view session state information, use the show vrrp command. The bold line shows the VRRP BFD session.
To disable all VRRP sessions on an interface, sessions for a particular VRRP group, or for a particular VRRP session on an interface, use the following commands. • Disable all VRRP sessions on an interface. INTERFACE mode no vrrp bfd all-neighbors • Disable all VRRP sessions in a VRRP group. VRRP mode bfd disable • Disable a particular VRRP session on an interface.
9 Border Gateway Protocol IPv4 (BGPv4) This chapter provides a general description of BGPv4 as it is supported in the Dell EMC Networking Operating System (OS). BGP protocol standards are listed in the Standards Compliance chapter. BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). The primary function of the BGP is to exchange network reachability information with other BGP systems.
IBGP provides routers inside the AS with the knowledge to reach routers external to the AS. EBGP routers exchange information with other EBGP routers as well as IBGP routers to maintain connectivity and accessibility. Figure 17. Internal BGP BGP version 4 (BGPv4) supports classless interdomain routing and aggregate routes and AS paths. BGP is a path vector protocol — a computer network in which BGP maintains the path that updated information takes as it diffuses through the network.
Figure 18. BGP Routers in Full Mesh The number of BGP speakers each BGP peer must maintain increases exponentially. Network management quickly becomes impossible. Sessions and Peers When two routers communicate using the BGP protocol, a BGP session is started. The two end-points of that session are Peers. A Peer is also called a Neighbor. Establish a Session Information exchange between peers is driven by events and timers. The focus in BGP is on the traffic routing policies.
State Description Idle BGP initializes all resources, refuses all inbound BGP connection attempts, and initiates a TCP connection to the peer. Connect In this state the router waits for the TCP connection to complete, transitioning to the OpenSent state if successful. If that transition is not successful, BGP resets the ConnectRetry timer and transitions to the Active state when the timer expires. Active The router resets the ConnectRetry timer to zero and returns to the Connect state.
Figure 19. BGP Router Rules 1 Router B receives an advertisement from Router A through eBGP. Because the route is learned through eBGP, Router B advertises it to all its iBGP peers: Routers C and D. 2 Router C receives the advertisement but does not advertise it to any peer because its only other peer is Router D, an iBGP peer, and Router D has already learned it through iBGP from Router B.
In non-deterministic mode (the bgp non-deterministic-med command is applied), paths are compared in the order in which they arrive. This method can lead to Dell EMC Networking OS choosing different best paths from a set of paths, depending on the order in which they were received from the neighbors because MED may or may not get compared between the adjacent paths.
c Paths with no MED are treated as “worst” and assigned a MED of 4294967295. 7 Prefer external (EBGP) to internal (IBGP) paths or confederation EBGP paths. 8 Prefer the path with the lowest IGP metric to the BGP if next-hop is selected when synchronization is disabled and only an internal path remains.
Figure 21. BGP Local Preference Multi-Exit Discriminators (MEDs) If two ASs connect in more than one place, a multi-exit discriminator (MED) can be used to assign a preference to a preferred path. MED is one of the criteria used to determine the best path, so keep in mind that other criteria may impact selection, as shown in the illustration in Best Path Selection Criteria. One AS assigns the MED a value and the other AS uses that value to decide the preferred path.
Figure 22. Multi-Exit Discriminators NOTE: Configuring the set metric-type internal command in a route-map advertises the IGP cost as MED to outbound EBGP peers when redistributing routes. The configured set metric value overwrites the default IGP cost. If the outbound route-map uses MED, it overwrites IGP MED. Origin The origin indicates the origin of the prefix, or how the prefix came into BGP. There are three origin codes: IGP, EGP, INCOMPLETE.
AS Path The AS path is the list of all ASs that all the prefixes listed in the update have passed through. The local AS number is added by the BGP speaker when advertising to a eBGP neighbor. NOTE: Any update that contains the AS path number 0 is valid. The AS path is shown in the following example. The origin attribute is shown following the AS path information (shown in bold).
MBGP uses either an IPv4 address configured on the interface (which is used to establish the IPv6 session) or a stable IPv4 address that is available in the box as the next-hop address. As a result, while advertising an IPv6 network, exchange of IPv4 routes does not lead to martian next-hop message logs. NOTE: It is possible to configure BGP peers that exchange both unicast and multicast network layer reachability information (NLRI), but you cannot connect multiprotocol BGP with BGP.
Ignore Router-ID in Best-Path Calculation You can avoid unnecessary BGP best-path transitions between external paths under certain conditions. The bgp bestpath routerid ignore command reduces network disruption caused by routing and forwarding plane changes and allows for faster convergence. Four-Byte AS Numbers You can use the 4-Byte (32-bit) format when configuring autonomous system numbers (ASNs). The 4-Byte support is advertised as a new BGP capability (4-BYTE-AS) in the OPEN message.
ASDOT representation combines the ASPLAIN and ASDOT+ representations. AS numbers less than 65536 appear in integer format (asplain); AS numbers equal to or greater than 65536 appear in the decimal format (asdot+). For example, the AS number 65526 appears as 65526 and the AS number 65546 appears as 1.10. Dynamic AS Number Notation Application Dell EMC Networking OS applies the ASN notation type change dynamically to the running-config statements.
DellEMC(conf-router_bgp)#sho conf ! router bgp 100 neighbor 172.30.1.250 local-as 65057 DellEMC(conf-router_bgp)#do show ip bgp BGP table version is 28093, local router ID is 172.30.1.57 AS Number Migration With this feature you can transparently change the AS number of an entire BGP network and ensure that the routes are propagated throughout the network while the migration is in progress.
3 Prepend "65001 65002" to as-path. Local-AS is prepended before the route-map to give an impression that update passed through a router in AS 200 before it reached Router B. BGP4 Management Information Base (MIB) The FORCE10-BGP4-V2-MIB enhances support for BGP management information base (MIB) with many new simple network management protocol (SNMP) objects and notifications (traps) defined in draft-ietf-idr-bgp4-mibv2-05. To see these enhancements, download the MIB from the Dell website.
• Multiple BPG process instances are not supported. Thus, the f10BgpM2PeerInstance field in various tables is not used to locate a peer. • Multiple instances of the same NLRI in the BGP RIB are not supported and are set to zero in the SNMP query response. • The f10BgpM2NlriIndex and f10BgpM2AdjRibsOutIndex fields are not used. • Carrying MPLS labels in BGP is not supported. The f10BgpM2NlriOpaqueType and f10BgpM2NlriOpaquePointer fields are set to zero. • 4-byte ASN is supported.
Item Default reuse = 750 suppress = 2000 max-suppress-time = 60 minutes external distance = 20 Distance internal distance = 200 local distance = 200 keepalive = 60 seconds Timers holdtime = 180 seconds Add-path Disabled Enabling BGP By default, BGP is not enabled on the system. Dell EMC Networking OS supports one autonomous system (AS) and assigns the AS number (ASN). To establish BGP sessions and route traffic, configure at least one BGP neighbor or peer.
NOTE: Use it only if you support 4-Byte AS numbers or if you support AS4 number representation. If you are supporting 4-Byte ASNs, enable this command. Disable 4-Byte support and return to the default 2-Byte format by using the no bgp four-octet-as-support command. You cannot disable 4-Byte support if you currently have a 4-Byte ASN configured. b Disabling 4-Byte AS numbers also disables ASDOT and ASDOT+ number representation. All AS numbers are displayed in ASPLAIN format.
The following example shows the show ip bgp summary command output (4–byte AS number displays). R2#show ip bgp summary BGP router identifier 192.168.10.2, local AS number 48735.
BGP state IDLE, in this state for 17:12:40 Last read 17:12:40, hold time is 180, keepalive interval is 60 seconds Received 0 messages, 0 notifications, 0 in queue Sent 0 messages, 0 notifications, 0 in queue Received 0 updates, Sent 0 updates Minimum time between advertisement runs is 5 seconds For address family: IPv4 Unicast BGP table version 0, neighbor version 0 0 accepted prefixes consume 0 bytes Prefix advertised 0, rejected 0, withdrawn 0 Connections established 0; dropped 0 Last reset never No activ
To configure AS4 number representations, use the following commands. • Enable ASPLAIN AS Number representation. CONFIG-ROUTER-BGP mode bgp asnotation asplain • NOTE: ASPLAIN is the default method Dell EMC Networking OS uses and does not appear in the configuration display. Enable ASDOT AS Number representation. CONFIG-ROUTER-BGP mode bgp asnotation asdot • Enable ASDOT+ AS Number representation.
Configuring Peer Groups To configure multiple BGP neighbors at one time, create and populate a BGP peer group. An advantage of peer groups is that members of a peer group inherit the configuration properties of the group and share same update policy. A maximum of 256 peer groups are allowed on the system. Create a peer group by assigning it a name, then adding members to the peer group. After you create a peer group, you can configure route policies for it.
When you add a peer to a peer group, it inherits all the peer group’s configured parameters.
BGP version 4 Minimum time between advertisement runs is 5 seconds For address family: IPv4 Unicast BGP neighbor is zanzibar, peer-group internal, Number of peers in this group 26 Peer-group members (* - outbound optimized): 10.68.160.1 10.68.161.1 10.68.162.1 10.68.163.1 10.68.164.1 10.68.165.1 10.68.166.1 10.68.167.1 10.68.168.1 10.68.169.1 10.68.170.1 10.68.171.1 10.68.172.1 10.68.173.1 10.68.174.1 10.68.175.1 10.68.176.1 10.68.177.1 10.68.178.1 10.68.179.1 10.68.180.1 10.68.181.1 10.68.182.1 10.68.183.
BGP neighbor is 100.100.100.100, remote AS 65517, internal link Member of peer-group test for session parameters BGP version 4, remote router ID 30.30.30.
neighbor 100.100.100.100 no shutdown DellEMC# Configuring Passive Peering When you enable a peer-group, the software sends an OPEN message to initiate a TCP connection. If you enable passive peering for the peer group, the software does not send an OPEN message, but it responds to an OPEN message.
• No Prepend: specifies that local AS values are not prepended to announcements from the neighbor. Format: IP Address: A.B.C.D. You must Configure Peer Groups before assigning it to an AS. This feature is not supported on passive peer groups. Example of the Verifying that Local AS Numbering is Disabled The first line in bold shows the actual AS number. The second two lines in bold show the local AS number (6500) maintained during migration.
router bgp 65123 bgp router-id 192.168.10.2 network 10.10.21.0/24 network 10.10.32.0/24 network 100.10.92.0/24 network 192.168.10.0/24 bgp four-octet-as-support neighbor 10.10.21.1 remote-as 65123 neighbor 10.10.21.1 filter-list Laura in neighbor 10.10.21.1 no shutdown neighbor 10.10.32.3 remote-as 65123 neighbor 10.10.32.3 no shutdown neighbor 100.10.92.9 remote-as 65192 neighbor 100.10.92.9 local-as 6500 neighbor 100.10.92.9 no shutdown neighbor 192.168.10.1 remote-as 65123 neighbor 192.168.10.
• The default is 120 seconds. Set maximum time to retain the restarting peer’s stale paths. CONFIG-ROUTER-BGP mode bgp graceful-restart [stale-path-time time-in-seconds] • The default is 360 seconds. Local router supports graceful restart as a receiver only. CONFIG-ROUTER-BGP mode bgp graceful-restart [role receiver-only] Enabling Neighbor Graceful Restart BGP graceful restart is active only when the neighbor becomes established. Otherwise, it is disabled.
To configure an AS-PATH ACL to filter a specific AS_PATH value, use these commands in the following sequence. 1 Assign a name to a AS-PATH ACL and enter AS-PATH ACL mode. CONFIGURATION mode ip as-path access-list as-path-name 2 Enter the parameter to match BGP AS-PATH for filtering. CONFIG-AS-PATH mode {deny | permit} filter parameter This is the filter that is used to match the AS-path. The entries can be any format, letters, numbers, or regular expressions.
Regular Expressions as Filters Regular expressions are used to filter AS paths or community lists. A regular expression is a special character used to define a pattern that is then compared with an input string. For an AS-path access list, as shown in the previous commands, if the AS path matches the regular expression in the access list, the route matches the access list. The following lists the regular expressions accepted in Dell EMC Networking OS.
DellEMC(config-as-path)#deny 32$ DellEMC(config-as-path)#ex DellEMC(conf)#router bgp 99 DellEMC(conf-router_bgp)#neighbor AAA filter-list Eagle in DellEMC(conf-router_bgp)#show conf ! router bgp 99 neighbor AAA peer-group neighbor AAA filter-list Eaglein neighbor AAA no shutdown neighbor 10.155.15.2 remote-as 32 neighbor 10.155.15.2 filter-list 1 in neighbor 10.155.15.
Enabling Additional Paths The add-path feature is disabled by default. NOTE: Dell EMC Networking OS recommends not using multipath and add path simultaneously in a route reflector. To allow multiple paths sent to peers, use the following commands. 1 Allow the advertisement of multiple paths for the same address prefix without the new paths replacing any previous ones. CONFIG-ROUTER-BGP mode bgp add-path [both|received|send] path-count count The range is from 2 to 64.
• • • • • local-AS: routes with the COMMUNITY attribute of NO_EXPORT_SUBCONFED. no-advertise: routes with the COMMUNITY attribute of NO_ADVERTISE. no-export: routes with the COMMUNITY attribute of NO_EXPORT. quote-regexp: then any number of regular expressions. The software applies all regular expressions in the list. regexp: then a regular expression.
deny 701:20 deny 702:20 deny 703:20 deny 704:20 deny 705:20 deny 14551:20 deny 701:112 deny 702:112 deny 703:112 deny 704:112 deny 705:112 deny 14551:112 deny 701:667 deny 702:667 deny 703:667 deny 704:666 deny 705:666 deny 14551:666 DellEMC# Filtering Routes with Community Lists To use an IP community list or IP extended community list to filter routes, you must apply a match community filter to a route map and then apply that route map to a BGP neighbor or peer group.
Manipulating the COMMUNITY Attribute In addition to permitting or denying routes based on the values of the COMMUNITY attributes, you can manipulate the COMMUNITY attribute value and send the COMMUNITY attribute with the route information. By default, Dell EMC Networking OS does not send the COMMUNITY attribute. To send the COMMUNITY attribute to BGP neighbors, use the following command. • Enable the software to send the router’s COMMUNITY attribute to the BGP neighbor or peer group specified.
Example of the show ip bgp community Command To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode. To view a route map configuration, use the show route-map command in EXEC Privilege mode. To view BGP routes matching a certain community number or a pre-defined BGP community, use the show ip bgp community command in EXEC Privilege mode. DellEMC>show ip bgp community BGP table version is 3762622, local router ID is 10.114.8.
• Change the LOCAL_PREF value. CONFIG-ROUTER-BGP mode bgp default local-preference value • value: the range is from 0 to 4294967295. The default is 100. To view the BGP configuration, use the show config command in CONFIGURATION ROUTER BGP mode or the show runningconfig bgp command in EXEC Privilege mode. A more flexible method for manipulating the LOCAL_PREF attribute value is to use a route map. 1 Enter the ROUTE-MAP mode and assign a name to a route map.
• If you do not use the all keyword, the next hop of only eBGP-learned routes is updated by the route reflector. If you use the all keyword, the next hop of both eBGP- and iBGP-learned routes are updated by the route reflector. Sets the next hop address. CONFIG-ROUTE-MAP mode set next-hop ip-address If the set next-hop command is applied on the out-bound interface using a route map, it takes precedence over the neighbor next-hop-self command.
NOTE: Dell EMC Networking OS supports up to 255 characters in a set community statement inside a route map. NOTE: You can create inbound and outbound policies. Each of the commands used for filtering has in and out parameters that you must apply. In Dell EMC Networking OS, the order of preference varies depending on whether the attributes are applied for inbound updates or outbound updates.
• If none of the routes match any of the filters in the prefix list, the route is denied. This action is called an implicit deny. (If you want to forward all routes that do not match the prefix list criteria, you must configure a prefix list filter to permit all routes. For example, you could have the following filter as the last filter in your prefix list permit 0.0.0.0/0 le 32). • After a route matches a filter, the filter’s action is applied. No additional filters are applied to the route.
ip as-path access-list as-path-name 2 Create a AS-PATH ACL filter with a deny or permit action. AS-PATH ACL mode {deny | permit} as-regular-expression 3 Return to CONFIGURATION mode. AS-PATH ACL exit 4 Enter ROUTER BGP mode. CONFIGURATION mode router bgp as-number 5 Filter routes based on the criteria in the configured route map.
To view a route reflector configuration, use the show config command in CONFIGURATION ROUTER BGP mode or the show running-config bgp in EXEC Privilege mode. Aggregating Routes Dell EMC Networking OS provides multiple ways to aggregate routes in the BGP routing table. At least one specific route of the aggregate must be in the routing table for the configured aggregate to become active. To aggregate routes, use the following command.
To view the configuration, use the show config command in CONFIGURATION ROUTER BGP mode. Enabling Route Flap Dampening When EBGP routes become unavailable, they “flap” and the router issues both WITHDRAWN and UPDATE notices. A flap is when a route: • is withdrawn • is readvertised after being withdrawn • has an attribute change The constant router reaction to the WITHDRAWN and UPDATE notices causes instability in the BGP process.
• • reuse: the range is from 1 to 20000. This number is compared to the flapping route’s Penalty value. If the Penalty value is less than the reuse value, the flapping route is once again advertised (or no longer suppressed). The default is 750. • suppress: the range is from 1 to 20000. This number is compared to the flapping route’s Penalty value. If the Penalty value is greater than the suppress value, the flapping route is no longer advertised (that is, it is suppressed). The default is 2000.
BGP table version is 855562, main routing table version 780266 122836 network entrie(s) and 221664 paths using 29697640 bytes of memory 34298 BGP path attribute entrie(s) using 1920688 bytes of memory 29577 BGP AS-PATH entrie(s) using 1384403 bytes of memory 184 BGP community entrie(s) using 7616 bytes of memory Dampening enabled. 0 history paths, 0 dampened paths, 0 penalized paths Neighbor AS MsgRcvd MsgSent TblVer 10.114.8.34 18508 82883 79977 780266 10.114.8.
To reset a BGP connection using BGP soft reconfiguration, use the clear ip bgp command in EXEC Privilege mode at the system prompt. When you enable soft-reconfiguration for a neighbor and you execute the clear ip bgp soft in command, the update database stored in the router is replayed and updates are reevaluated. With this command, the replay and update process is triggered only if a routerefresh request is not negotiated with the peer.
2 In ROUTER BGP mode, enter the following command: ROUTER BGP Mode shutdown all You can use the no shutdown all command in the ROUTER BGP mode to re-enable all the BGP interface. You can also enable or disable BGP neighbors corresponding to the IPv4 unicast or multicast groups and the IPv6 unicast groups.
NOTE: This behavior applies to all BGP neighbors. Meaning, BGP neighbors that were explicitly disabled before global shutdown also remain in disabled state. Enable these neighbors individually using the no shutdown command. Route Map Continue The BGP route map continue feature, continue [sequence-number], (in ROUTE-MAP mode) allows movement from one routemap entry to a specific route-map entry (the sequence number).
• If the peer has not been activated in any AFI/SAFI, the peer remains in Idle state. Most Dell EMC Networking OS BGP IPv4 unicast commands are extended to support the IPv4 multicast RIB using extra options to the command. For a detailed description of the MBGP commands, refer to the Dell EMC Networking OS Command Line Interface Reference Guide. • Enables support for the IPv4 multicast family on the BGP node.
• debug ip bgp dampening [in | out] View information about local BGP state changes and other BGP events. EXEC Privilege mode • debug ip bgp [ip-address | peer-group peer-group-name] events [in | out] View information about BGP KEEPALIVE messages. EXEC Privilege mode • debug ip bgp [ip-address | peer-group peer-group-name] keepalive [in | out] View information about BGP notifications received from or sent to neighbors.
Minimum time between advertisement runs is 30 seconds Minimum time before advertisements start is 0 seconds Capabilities received from neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) For address family: IPv4 Unicast BGP table version 1395, neighbor version 1394 Prefixes accepted 1 (consume 4 bytes), 0 withdrawn by peer Prefixes advertised 0, rejected 0, 0
00000000 00000001 0181a1e4 0181a25c 41af9400 00000000 PDU[2] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[3] : len 19, captured 00:34:51 ago ffffffff ffffffff ffffffff ffffffff 00130400 PDU[4] : len 19, captured 00:34:22 ago ffffffff ffffffff ffffffff ffffffff 00130400 [. . .] Outgoing packet capture enabled for BGP neighbor 20.20.20.
Figure 24. Sample Configurations Example of Enabling BGP (Router 1) R1# conf R1(conf)#int loop 0 R1(conf-if-lo-0)#ip address 192.168.128.1/24 R1(conf-if-lo-0)#no shutdown R1(conf-if-lo-0)#show config ! interface Loopback 0 ip address 192.168.128.1/24 no shutdown R1(conf-if-lo-0)#int gi 1/21 R1(conf-if-gi-1/21)#ip address 10.0.1.21/24 R1(conf-if-gi-1/21)#no shutdown R1(conf-if-gi-1/21)#show config ! interface GigabitEthernet 1/21 ip address 10.0.1.
R1(conf-router_bgp)#neighbor 192.168.128.2 update-source loop 0 R1(conf-router_bgp)#neighbor 192.168.128.3 remote 100 R1(conf-router_bgp)#neighbor 192.168.128.3 no shut R1(conf-router_bgp)#neighbor 192.168.128.3 update-source loop 0 R1(conf-router_bgp)#show config ! router bgp 99 network 192.168.128.0/24 neighbor 192.168.128.2 remote-as 99 neighbor 192.168.128.2 update-source Loopback 0 neighbor 192.168.128.2 no shutdown neighbor 192.168.128.3 remote-as 100 neighbor 192.168.128.
R3(conf-if-gi-3/11)#no shutdown R3(conf-if-gi-3/11)#show config ! interface GigabitEthernet 3/11 ip address 10.0.3.33/24 no shutdown R3(conf-if-lo-0)#int gi 3/21 R3(conf-if-gi-3/21)#ip address 10.0.2.3/24 R3(conf-if-gi-3/21)#no shutdown R3(conf-if-gi-3/21)#show config ! interface GigabitEthernet 3/21 ip address 10.0.2.3/24 no shutdown R3(conf-if-gi-3/21)# R3(conf-if-gi-3/21)#router bgp 100 R3(conf-router_bgp)#show config ! router bgp 100 R3(conf-router_bgp)#network 192.168.128.
CISCO_ROUTE_REFRESH(128) Capabilities advertised to neighbor for IPv4 Unicast : MULTIPROTO_EXT(1) ROUTE_REFRESH(2) CISCO_ROUTE_REFRESH(128) Update source set to Loopback 0 Peer active in peer-group outbound optimization For address family: IPv4 Unicast BGP table version 1, neighbor version 1 Prefixes accepted 1 (consume 4 bytes), withdrawn 0 by peer Prefixes advertised 1, denied 0, withdrawn 0 from peer Connections established 2; dropped 1 Last reset 00:00:57, due to user reset Notification History 'Connect
2 BGP path attribute entrie(s) using 128 bytes of memory 2 BGP AS-PATH entrie(s) using 90 bytes of memory 2 neighbor(s) using 9216 bytes of memory Neighbor AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/Pfx 192.168.128.1 99 140 136 2 0 (0) 00:11:24 1 192.168.128.
BGP version 4, remote router ID 192.168.128.
10 Content Addressable Memory (CAM) CAM is a type of memory that stores information in the form of a lookup table. On Dell EMC Networking systems, CAM stores Layer 2 (L2) and Layer 3 (L3) forwarding information, access-lists (ACLs), flows, and routing policies. CAM Allocation CAM Allocation for Ingress To allocate the space for regions such has L2 ingress ACL, IPV4 ingress ACL, IPV6 ingress ACL, IPV4 QoS, L2 QoS, PBR, VRF ACL, and so forth, use the cam-acl command in CONFIGURATION mode.
NOTE: When you reconfigure CAM allocation, use the nlbclusteracl number command to change the number of NLB ARP entries. The range is from 0 to 2. The default value is 0. At the default value of 0, eight NLB ARP entries are available for use. This platform supports upto 512 CAM entries. Select 1 to configure 256 entries. Select 2 to configure 1024 entries.
cam-acl {default | l2acl number ipv4acl number ipv6acl number ipv4qos number l2qos number l2pt number ipmacacl number vman-qos | vman-dual-qos number ecfmacl number nlbcluster number ipv4pbr number openflow number | fcoe number iscsioptacl number [vrfv4acl number] NOTE: If you do not enter the allocation values for the CAM regions, the value is 0. 3 Execute write memory and verify that the new settings are written to the CAM on the next boot. EXEC Privilege mode show cam-acl 4 Reload the system.
L2Qos L2PT IpMacAcl VmanQos VmanDualQos EcfmAcl FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl : : : : : : : : : : : : 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 2 2 0 0 DellEMC(conf)# Example of Viewing CAM-ACL Settings NOTE: If you change the cam-acl setting from CONFIGURATION mode, the output of this command does not reflect any changes until you save the running-configuration and reload the chassis.
Ipv6Acl Ipv4Qos L2Qos L2PT IpMacAcl VmanQos VmanDualQos EcfmAcl FcoeAcl iscsiOptAcl ipv4pbr vrfv4Acl Openflow fedgovacl : : : : : : : : : : : : : : 0 2 1 0 0 0 0 0 0 0 0 0 0 0 DellEMC# View CAM Usage View the amount of CAM space available, used, and remaining in each partition (including IPv4Flow and Layer 2 ACL sub- partitions) using the show cam-usage command in EXEC Privilege mode The following output shows CAM blocks usage for Layer 2 and Layer 3 ACLs and other processes that use CAM space: Example
Setting CAM Threshold and Silence Period To configure the CAM threshold and silence period, use the following commands. • Assign the CAM threshold percentage CONFIGURATION mode cam-threshold threshold {default | threshold-percent} The range of threshold value is from 1 to 100. The default threshold value is 90 percent. • Assign the silence period for syslog warning.
92 90 89 No syslog CAM Optimization When you enable the CAM optimization, if a Policy Map containing classification rules (ACL and/or DSCP/ ip-precedence rules) is applied to more than one physical interface on the same port-pipe, only a single copy of the policy is written (only one FP entry is used). When you disable this command, the system behaves as described in this chapter. Troubleshoot CAM Profiling The following section describes CAM profiling troubleshooting.
11 Control Plane Policing (CoPP) Control plane policing (CoPP) uses access control list (ACL) rules and quality of service (QoS) policies to create filters for a system’s control plane. That filter prevents traffic not specifically identified as legitimate from reaching the system control plane, rate-limits, traffic to an acceptable level.
Figure 26. CoPP Implemented Versus CoPP Not Implemented Configure Control Plane Policing The system can process a maximum of 4200 packets per second (PPS). Protocols that share a single queue may experience flaps if one of the protocols receives a high rate of control traffic even though per protocol CoPP is applied. This happens because queue-based rate limiting is applied first.
CoPP policies are configured by creating extended ACL rules and specifying rate-limits through QoS policies. The ACLs and QoS policies are assigned as service-policies. Configuring CoPP for Protocols This section lists the commands necessary to create and enable the service-policies for CoPP. For complete information about creating ACLs and QoS rules, refer to Access Control Lists (ACLs) and Quality of Service (QoS).
8 Assign the protocol based the service policy on the control plane. Enabling this command on a port-pipe automatically enables the ACL and QoS rules creates with the cpu-qos keyword. CONTROL-PLANE mode service-policy rate-limit-protocols Examples of Configuring CoPP for Different Protocols The following example shows creating the IP/IPv6/MAC extended ACL.
DellEMC(conf-policy-map-in-cpuqos)#class-map class-ipv6 qos-policy rate_limit_200k DellEMC(conf-policy-map-in-cpuqos)#exit The following example shows creating the control plane service policy. DellEMC(conf)#control-plane-cpuqos DellEMC(conf-control-cpuqos)#service-policy rate-limit-protocols egressFP_rate_policy DellEMC(conf-control-cpuqos)#exit Configuring CoPP for CPU Queues Controlling traffic on the CPU queues does not require ACL rules, but does require QoS policies.
The following example shows creating the control plane service policy. DellEMC#conf DellEMC(conf)#control-plane DellEMC(conf-control-plane)#service-policy rate-limit-cpu-queues cpuq_rate_policy CoPP for OSPFv3 Packets You can create an IPv6 ACL for control-plane traffic policing for OSPFv3, in addition to the CoPP support for VRRP, BGP, and ICMP. You can use the ipv6 access-list name cpu-qos permit ospfv3 command to allow CoPP traffic for OSPFv3.
As part of enhancements, CPU queues are increased from 8 to 12 on CPU port. However, the front-end port and the backplane ports support only 8 queues. As a result, when packets are transmitted to the local CPU, the CPU uses Q0-Q11 queues. The control packets that are tunneled to the master unit are isolated from the data queues and the control queues in the backplane links. Control traffic must be sent over the control queues Q4-Q7 on higig links.
• NDP Packets in VLT peer routing enable • • VLT peer routing enable cases each VLT node will have route entry for link local address of both self and peer VLT node. Peer VLT link local entry will have egress port as ICL link. And Actual link local address will have entry to CopyToCpu. But NDP packets destined to peer VLT node needs to be taken to CPU and tunneled to the peer VLT node..
unicast packets. This CLI knob to turn off the catch-all route is of use in networks where the user does not want to generate Destination Unreachable messages and have the CPU queue’s bandwidth available for higher priority control-plane traffic. Configuring CoPP for OSPFv3 You can create an IPv6 ACL for control-plane traffic policing for OSPFv3, in addition to the CoPP support for VRRPv3, BGPv6, and ICMPv6.
Viewing Queue Rates Example of Viewing Queue Rates DellEMC#show cpu-queue rate cp Service-Queue Rate (PPS) -----------------------Q0 1300 Q1 300 Q2 275 Q3 400 Q4 2000 Q5 300 Q6 400 Q7 400 Q8 400 Q9 600 Q10 300 Q11 300 DellEMC# Burst (Packets) ---------512 50 50 50 50 50 50 50 50 50 50 50 Example of Viewing Queue Mapping To view the queue mapping for each configured protocol, use the show ip protocol-queue-mapping command.
TCP (BGP) ICMP VRRP any/179 any any 179/any any any _ _ _ Q6 Q6 Q7 CP CP CP _ _ _ DellEMC# Control Plane Policing (CoPP) 245
12 Dynamic Host Configuration Protocol (DHCP) DHCP is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on configuration policies determined by network administrators.
The following table lists common DHCP options. Option Number and Description Subnet Mask Option 1 Specifies the client’s subnet mask. Router Option 3 Specifies the router IP addresses that may serve as the client’s default gateway. Domain Name Server Option 6 Domain Name Option 15 Specifies the domain name servers (DNSs) that are available to the client. Specifies the domain name that clients should use when resolving hostnames via DNS.
Option Number and Description User Port Stacking Option 230 Set the stacking option variable to provide DHCP server stack-port detail when the DHCP offer is set. End Option 255 Signals the last option in the DHCP packet. Assign an IP Address using DHCP The following section describes DHCP and the client in a network. When a client joins a network: 1 The client initially broadcasts a DHCPDISCOVER message on the subnet to discover available DHCP servers.
Implementation Information The following describes DHCP implementation. • Dell EMC Networking implements DHCP based on RFC 2131 and RFC 3046. • IP source address validation is a sub-feature of DHCP Snooping; the Dell EMC Networking OS uses access control lists (ACLs) internally to implement this feature and as such, you cannot apply ACLs to an interface which has IP source address validation.
Configuring the Server for Automatic Address Allocation Automatic address allocation is an address assignment method by which the DHCP server leases an IP address to a client from a pool of available addresses. An address pool is a range of IP addresses that the DHCP server may assign. The subnet number indexes the address pools. To create an address pool, follow these steps. 1 Access the DHCP server CLI context. CONFIGURATION mode ip dhcp server 2 Create an address pool and give it a name.
Excluding Addresses from the Address Pool The DHCP server assumes that all IP addresses in a DHCP address pool are available for assigning to DHCP clients. You must specify the IP address that the DHCP server should not assign to clients. To exclude an address, follow this step. • Exclude an address range from DHCP assignment. The exclusion applies to all configured pools. DHCP mode excluded-address Specifying an Address Lease Time To specify an address lease time, use the following command.
Using NetBIOS WINS for Address Resolution Windows internet naming service (WINS) is a name resolution service that Microsoft DHCP clients use to correlate host names to IP addresses within a group of networks. Microsoft DHCP clients can be one of four types of NetBIOS nodes: broadcast, peer-to-peer, mixed, or hybrid. 1 Specify the NetBIOS WINS name servers, in order of preference, that are available to Microsoft Dynamic Host Configuration Protocol (DHCP) clients.
Using DHCP Clear Commands To clear DHCP binding entries, address conflicts, and server counters, use the following commands. • Clear DHCP binding entries for the entire binding table. EXEC Privilege mode. clear ip dhcp binding • Clear a DHCP binding entry for an individual IP address. EXEC Privilege mode. clear ip dhcp binding ip address Configure the System to be a Relay Agent DHCP clients and servers request and offer configuration information via broadcast DHCP messages.
Figure 29. Configuring a Relay Agent To view the ip helper-address configuration for an interface, use the show ip interface command from EXEC privilege mode. Example of the show ip interface Command R1_E600#show ip int gigabitethernet 1/3 GigabitEthernet 1/3 is up, line protocol is down Internet address is 10.11.0.1/24 Broadcast address is 10.11.0.255 Address determined by user input IP MTU is 1500 bytes Helper address is 192.168.0.1 192.168.0.
Configure the System to be a DHCP Client A DHCP client is a network device that requests an IP address and configuration parameters from a DHCP server. Implement the DHCP client functionality as follows: • The switch can obtain a dynamically assigned IP address from a DHCP server. A start-up configuration is not received. Use bare metal provisioning (BMP) to receive configuration parameters (Dell EMC Networking OS version and a configuration file). BMP is enabled as a factory-default setting on a switch.
To manually configure a static IP address on an interface, use the ip address command. A prompt displays to release an existing dynamically acquired IP address. If you confirm, the ability to receive a DHCP server-assigned IP address is removed. To enable acquiring a dynamic IP address from a DHCP server on an interface configured with a static IP address, use the ip address dhcp command. A prompt displays to confirm the IP address reconfiguration.
server are in the same or different subnets. The management default route is deleted if the management IP address is released like other DHCP client management routes. • ip route for 0.0.0.0 takes precedence if it is present or added later. • Management routes added by a DHCP client display with Route Source as DHCP in the show ip management route and show ip management-route dynamic command output.
• An entry in the DHCP snooping table is not added for a DHCP client interface. DHCP Server A switch can operate as a DHCP client and a DHCP server. DHCP client interfaces cannot acquire a dynamic IP address from the DHCP server running on the switch. Acquire a dynamic IP address from another DHCP server. Virtual Router Redundancy Protocol (VRRP) Do not enable the DHCP client on an interface and set the priority to 255 or assign the same DHCP interface IP address to a VRRP virtual group.
• track the number of address requests per relay agent. Restricting the number of addresses available per relay agent can harden a server against address exhaustion attacks. • associate client MAC addresses with a relay agent to prevent offering an IP address to a client spoofing the same MAC address on a different relay agent. • assign IP addresses according to the relay agent. This prevents generating DHCP offers in response to requests from an unauthorized relay agent.
DHCP Snooping for a Multi-Tenant Host You can configure the DHCP snooping feature such that multiple IP addresses are expected for the same MAC address. You can use the ip dhcp snooping command multiple times to map the same MAC address with different IP addresses. This configuration is also used for dynamic ARP inspection (DAI) and source address validation (SAV). The DAI and SAV tables reflect the same entries in the DHCP snooping binding table.
CONFIGURATION mode ipv6 dhcp snooping vlan vlan-id Adding a Static Entry in the Binding Table To add a static entry in the binding table, use the following command. • Add a static entry in the binding table. EXEC Privilege mode ip dhcp snooping binding mac mac-address vlan-id vlan-id ip ip-address interface interfacetype interface-number lease lease-value If multiple IP addresses are expected for the same MAC address, repeat this step for all IP addresses.
show ip dhcp snooping • Display the contents of the binding table. EXEC Privilege mode show ip dhcp snooping binding Example of the show ip dhcp snooping Command View the DHCP snooping statistics with the show ip dhcp snooping command. DellEMC#show ip dhcp snooping IP IP IP IP DHCP DHCP DHCP DHCP Snooping Snooping Mac Verification Relay Information-option Relay Trust Downstream : : : : Enabled. Disabled. Disabled. Disabled.
The following example shows a sample output of the show ip dhcp snooping binding command for a device connected to one of the VLT peers only (orphaned). The physical interface is the one that is directly connected to the VLT peer. DellEMC#show ip dhcp snooping binding Codes : S - Static D - Dynamic IP Address MAC Address Expires(Sec) Type VLAN Interface ========================================================================= 10.1.1.100 00:00:a0:00:00:00 39735 S Vl 200 Gi 1/4 10.1.1.
Drop DHCP Packets on Snooped VLANs Only Binding table entries are deleted when a lease expires or the relay agent encounters a DHCPRELEASE. Line cards maintain a list of snooped VLANs. When the binding table fills, DHCP packets are dropped only on snooped VLANs, while such packets are forwarded across non-snooped VLANs. Because DHCP packets are dropped, no new IP address assignments are made. However, DHCP release and decline packets are allowed so that the DHCP snooping table can decrease in size.
NOTE: Dynamic ARP inspection (DAI) uses entries in the L2SysFlow CAM region, a sub-region of SystemFlow. One CAM entry is required for every DAI-enabled VLAN. You can enable DAI on up to 16 VLANs on a system. SystemFlow has 102 entries by default. This region comprises two sub-regions: L2Protocol and L2SystemFlow. L2Protocol has 87 entries; L2SystemFlow has 15 entries. Six L2SystemFlow entries are used by Layer 2 protocols, leaving nine for DAI.
• Specify an interface as trusted so that ARPs are not validated against the binding table. INTERFACE mode arp inspection-trust Dynamic ARP inspection is supported on Layer 2 and Layer 3. Source Address Validation Using the DHCP binding table, Dell EMC Networking OS can perform three types of source address validation (SAV). Table 16.
NOTE: Before enabling SAV With VLAN option, allocate at least one FP block to the ipmacacl CAM region. DHCP MAC Source Address Validation DHCP MAC source address validation (SAV) validates a DHCP packet’s source hardware address against the client hardware address field (CHADDR) in the payload. Dell EMC Networking OS ensures that the packet’s source MAC address is checked against the CHADDR field in the DHCP header only for packets from snooped VLANs. • Enable DHCP MAC SAV.
Viewing the Number of SAV Dropped Packets The following output of the show ip dhcp snooping source-address-validation discard-counters command displays the number of SAV dropped packets.
13 Equal Cost Multi-Path (ECMP) This chapter describes configuring ECMP. This chapter describes configuring ECMP. ECMP for Flow-Based Affinity ECMP for flow-based affinity includes link bundle monitoring. Configuring the Hash Algorithm TeraScale has one algorithm that is used for link aggregation groups (LAGs), ECMP, and NH-ECMP, and ExaScale can use three different algorithms for each of these features. To adjust the ExaScale behavior to match TeraScale, use the following command.
Configuring the Hash Algorithm Seed Deterministic ECMP sorts ECMPs in order even though RTM provides them in a random order. However, the hash algorithm uses as a seed the lower 12 bits of the chassis MAC, which yields a different hash result for every chassis. This behavior means that for a given flow, even though the prefixes are sorted, two unrelated chassis can select different hops.
ECMP bundle - 1 Utilization[In Percent] - 44 Alarm State - Active Interface Line Protocol Utilization[In Percent] Gi 1/1 Up 36 Gi 1/1 Up 52 Managing ECMP Group Paths To avoid path degeneration, configure the maximum number of paths for an ECMP route that the L3 CAM can hold. When you do not configure the maximum number of routes, the CAM can hold a maximum ECMP per route. To configure the maximum number of paths, use the following command.
• Modify the threshold for monitoring ECMP group bundles. CONFIGURATION mode link-bundle-distribution trigger-threshold {percent} The range is from 1 to 90%. • The default is 60%. Display details for an ECMP group bundle. EXEC mode show link-bundle-distribution ecmp-group ecmp-group-id The range is from 1 to 64. Viewing an ECMP Group NOTE: An ecmp-group index is generated automatically for each unique ecmp-group when you configure multipath routes to the same network.
14 FIPS Cryptography Federal information processing standard (FIPS) cryptography provides cryptographic algorithms conforming to various FIPS standards published by the National Institute of Standards and Technology (NIST), a non-regulatory agency of the US Department of Commerce. FIPS mode is also validated for numerous platforms to meet the FIPS-140-2 standard for a software-based cryptographic module. This chapter describes how to enable FIPS cryptography requirements on Dell EMC Networking platforms.
Enabling FIPS Mode To enable or disable FIPS mode, use the console port. Secure the host attached to the console port against unauthorized access. Any attempts to enable or disable FIPS mode from a virtual terminal session are denied. When you enable FIPS mode, the following actions are taken: • If enabled, the SSH server is disabled. • All open SSH and Telnet sessions, as well as all SCP and FTP file transfers, are closed.
Examples of the show fips status and show system Commands The following example shows the show fips status command. DellEMC#show fips status FIPS Mode : Enabled for the system using the show system command. The following example shows the show system command.
15 Force10 Resilient Ring Protocol (FRRP) FRRP provides fast network convergence to Layer 2 switches interconnected in a ring topology, such as a metropolitan area network (MAN) or large campuses. FRRP is similar to what can be achieved with the spanning tree protocol (STP), though even with optimizations, STP can take up to 50 seconds to converge (depending on the size of network and node of failure) and may require 4 to 5 seconds to reconverge.
Ring Status The ring failure notification and the ring status checks provide two ways to ensure the ring remains up and active in the event of a switch or port failure. Ring Checking At specified intervals, the Master node sends a ring health frame (RHF) through the ring. If the ring is complete, the frame is received on its secondary port and the Master node resets its fail-period timer and continues normal operation.
Member VLAN Spanning Two Rings Connected by One Switch A member VLAN can span two rings interconnected by a common switch, in a figure-eight style topology. A switch can act as a Master node for one FRRP group and a Transit for another FRRP group, or it can be a Transit node for both rings. In the following example, FRRP 101 is a ring with its own Control VLAN, and FRRP 202 has its own Control VLAN running on another ring. A Member VLAN that spans both rings is added as a Member VLAN to both FRRP groups.
• One Master node per ring — all other nodes are Transit. • Each node has two member interfaces — primary and secondary. • There is no limit to the number of nodes on a ring. • Master node ring port states — blocking, pre-forwarding, forwarding, and disabled. • Transit node ring port states — blocking, pre-forwarding, forwarding, and disabled. • STP disabled on ring interfaces. • Master node secondary port is in blocking state during Normal operation.
Concept Explanation • Hello RHF (HRHF) — These frames are processed only on the Master node’s Secondary port. The Transit nodes pass the HRHF through without processing it. An HRHF is sent at every Hello interval. • Topology Change RHF (TCRHF) — These frames contains ring status, keepalive, and the control and member VLAN hash. The TCRHF is processed at each node of the ring.
Configuring the Control VLAN Control and member VLANS are configured normally for Layer 2. Their status as control or member is determined at the FRRP group commands. For more information about configuring VLANS in Layer 2 mode, refer to Layer 2. Be sure to follow these guidelines: • All VLANS must be in Layer 2 mode. • You can only add ring nodes to the VLAN. • A control VLAN can belong to one FRRP group only. • Tag control VLAN ports.
CONFIG-FRRP mode. no disable Configuring and Adding the Member VLANs Control and member VLANS are configured normally for Layer 2. Their status as Control or Member is determined at the FRRP group commands. For more information about configuring VLANS in Layer 2 mode, refer to the Layer 2 chapter. Be sure to follow these guidelines: • All VLANS must be in Layer 2 mode. • Tag control VLAN ports. Member VLAN ports, except the Primary/Secondary interface, can be tagged or untagged.
no disable Setting the FRRP Timers To set the FRRP timers, use the following command. NOTE: Set the Dead-Interval time 3 times the Hello-Interval. • Enter the desired intervals for Hello-Interval or Dead-Interval times. CONFIG-FRRP mode. timer {hello-interval|dead-interval} milliseconds • Hello-Interval: the range is from 50 to 2000, in increments of 50 (default is 500). • Dead-Interval: the range is from 50 to 6000, in increments of 50 (default is 1500).
show frrp summary Ring ID: the range is from 1 to 255. Troubleshooting FRRP To troubleshoot FRRP, use the following information. Configuration Checks • • • • • • Each Control Ring must use a unique VLAN ID. Only two interfaces on a switch can be Members of the same control VLAN. There can be only one Master node for any FRRP group. You can configure FRRP on Layer 2 interfaces only. Spanning Tree (if you enable it globally) must be disabled on both Primary and Secondary interfaces when you enable FRRP.
no shutdown ! interface Vlan 101 no ip address tagged GigabitEthernet 2/14,31 no shutdown ! interface Vlan 201 no ip address tagged GigabitEthernet 2/14,31 no shutdown ! protocol frrp 101 interface primary GigabitEthernet 2/14 secondary GigabitEthernet 2/31 control-vlan 101 member-vlan 201 mode transit no disable Example of R3 TRANSIT interface GigabitEthernet 3/14 no ip address switchport no shutdown ! interface GigabitEthernet 3/21 no ip address switchport no shutdown ! interface Vlan 101 no ip address ta
16 GARP VLAN Registration Protocol (GVRP) The generic attribute registration protocol (GARP) VLAN registration protocol (GVRP), defined by the IEEE 802.1q specification, is a Layer 2 network protocol that provides for automatic VLAN configuration of switches. GVRP-compliant switches use GARP to register and deregister attribute values, such as VLAN IDs, with each other.
• Configure GVRP Registration • Configure a GARP Timer • RPM Redundancy Configure GVRP To begin, enable GVRP. To facilitate GVRP communications, enable GVRP globally on each switch. Then, GVRP configuration is per interface on a switch-by-switch basis. Enable GVRP on each port that connects to a switch where you want GVRP information exchanged. In the following example, GVRP is configured on VLAN trunk ports. Figure 31.
Enabling GVRP Globally To configure GVRP globally, use the following command. • Enable GVRP for the entire switch. CONFIGURATION mode gvrp enable Example of Configuring GVRP DellEMC(conf)#protocol gvrp DellEMC(config-gvrp)#no disable DellEMC(config-gvrp)#show config ! protocol gvrp no disable DellEMC(config-gvrp)# To inspect the global configuration, use the show gvrp brief command. Enabling GVRP on a Layer 2 Interface To enable GVRP on a Layer 2 interface, use the following command.
Based on the configuration in the following example, the interface is not removed from VLAN 34 or VLAN 35 despite receiving a GVRP Leave message. Additionally, the interface is not dynamically added to VLAN 45 or VLAN 46, even if a GVRP Join message is received.
• 290 RPM Synchronization GARP VLAN Registration Protocol (GVRP)
17 High Availability (HA) High availability (HA) is supported on Dell EMC Networking OS. HA is a collection of features that preserves system continuity by maximizing uptime and minimizing packet loss during system disruptions. To support all the features within the HA collection, you should have the latest boot code. The following table lists the boot code requirements as of this Dell EMC Networking OS release. Table 17. Boot Code Requirements Component Boot Code S3124 1 2.0.
Example of the show redundancy Command DellEMC#show redundancy -- Stack-unit Status ------------------------------------------------Mgmt ID: 1 Stack-unit ID: 12 Stack-unit Redundancy Role: Primary Stack-unit State: Active Stack-unit SW Version: 1-0(0-4679) Link to Peer: Up -- PEER Stack-unit Status ------------------------------------------------Stack-unit State: Standby Peer Stack-unit ID: 5 Stack-unit SW Version: 1-0(0-4679) -- Stack-unit Redundancy Configuration ------------------------------------------
EXEC Privilege mode redundancy force-failover stack-unit Example of the redundancy force-failover stack-unit Command Dell#redundancy force-failover stack-unit System configuration has been modified. Save? [yes/no]: yes Proceed with Stack-unit hot failover [confirm yes/no]:yes Dell# Disabling Auto-Reboot To disable auto-reboot, use the following command. • Prevent a failed stack unit from rebooting after a failover.
Dell# Dell(conf)#interface gigabitethernet 1/1 Dell(conf-if-gi-1/1)# Removing a Provisioned Logical Stack Unit To remove the line card configuration, use the following command. • To remove a logical stack-unit configuration, use the following command: CONFIGURATION mode no stack-unit unit_id provision Hitless Behavior Hitless is a protocol-based system behavior that makes a stack unit failover on the local system transparent to remote systems.
Software Resiliency During normal operations, Dell EMC Networking OS monitors the health of both hardware and software components in the background to identify potential failures, even before these failures manifest. Software Component Health Monitoring On each of the line cards and the stack unit, there are a number of software components.
System Log Event messages provide system administrators diagnostics and auditing information. Dell EMC Networking OS sends event messages to the internal buffer, all terminal lines, the console, and optionally to a syslog server. For more information about event messages and configurable options, refer to Management. Hot-Lock Behavior Dell EMC Networking OS hot-lock features allow you to append and delete their corresponding content addressable memory (CAM) entries dynamically without disrupting traffic.
18 Internet Group Management Protocol (IGMP) Internet group management protocol (IGMP) is a Layer 3 multicast protocol that hosts use to join or leave a multicast group. Multicast is premised on identifying many hosts by a single destination IP address; hosts represented by the same IP address are a multicast group. Multicast routing protocols (such as protocol-independent multicast [PIM]) use the information in IGMP messages to discover which groups are active and to populate the multicast routing table.
leaves a multicast group by sending an IGMP message to its IGMP Querier. The querier is the router that surveys a subnet for multicast receivers and processes survey responses to populate the multicast routing table. IGMP messages are encapsulated in IP packets, as shown in the following illustration. Figure 32.
3 Any remaining hosts respond to the query according to the delay timer mechanism (refer to Adjusting Query and Response Timers). If no hosts respond (because there are none remaining in the group), the querier waits a specified period and sends another query. If it still receives no response, the querier removes the group from the list associated with forwarding port and stops forwarding traffic for that group to the subnet. IGMP Version 3 Conceptually, IGMP version 3 behaves the same as version 2.
Figure 34. IGMP Version 3–Capable Multicast Routers Address Structure Joining and Filtering Groups and Sources The following illustration shows how multicast routers maintain the group and source information from unsolicited reports. 1 The first unsolicited report from the host indicates that it wants to receive traffic for group 224.1.1.1. 2 The host’s second report indicates that it is only interested in traffic from group 224.1.1.1, source 10.11.1.1.
Figure 35. Membership Reports: Joining and Filtering Leaving and Staying in Groups The following illustration shows how multicast routers track and refresh state changes in response to group-and-specific and general queries. 1 Host 1 sends a message indicating it is leaving group 224.1.1.1 and that the included filter for 10.11.1.1 and 10.11.1.2 are no longer necessary.
Figure 36. Membership Queries: Leaving and Staying Configure IGMP Configuring IGMP is a two-step process. 1 Enable multicast routing using the ip multicast-routing command. 2 Enable a multicast routing protocol.
Viewing IGMP Enabled Interfaces Interfaces that are enabled with PIM-SM are automatically enabled with IGMP. To view IGMP-enabled interfaces, use the following command. • View IGMP-enabled interfaces. EXEC Privilege mode show ip igmp interface Example of the show ip igmp interface Command DellEMC#show ip igmp interface GigabitEthernet 3/10 Inbound IGMP access group is not set Internet address is 165.87.34.
EXEC Privilege mode show ip igmp groups Example of the show ip igmp groups Command DellEMC#show ip igmp groups Total Number of Groups: 2 IGMP Connected Group Membership Group Address Interface 225.1.1.1 GigabitEthernet 1/1 225.1.2.1 GigabitEthernet 1/1 Mode IGMPV2 IGMPV2 Uptime 00:11:19 00:10:19 Expires 00:01:50 00:01:50 Last Reporter 165.87.34.100 165.87.31.100 Adjusting Timers The following sections describe viewing and adjusting timers.
Preventing a Host from Joining a Group You can prevent a host from joining a particular group by blocking specific IGMP reports using an extended access list containing the permissible source-group pairs. NOTE: For rules in IGMP access lists, source is the multicast source, not the source of the IGMP packet. For IGMPv2, use the keyword any for source (as shown in the following example) because the IGMPv2 hosts do not know in advance who the source is for the group in which they are interested.
Figure 37. Preventing a Host from Joining a Group The following table lists the location and description shown in the previous illustration. Table 18. Preventing a Host from Joining a Group — Description Location Description 1/21 • • • • Interface GigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 • • • Interface GigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
Location Description • no shutdown 2/1 • • • • Interface GigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.1.1/24 no shutdown 2/11 • • • • Interface GigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 • • • • Interface GigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 • • • • Interface GigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.
Enabling IGMP Immediate-Leave If the querier does not receive a response to a group-specific or group-and-source query, it sends another (querier robustness value). Then, after no response, it removes the group from the outgoing interface for the subnet. IGMP immediate leave reduces leave latency by enabling a router to immediately delete the group membership on an interface after receiving a Leave message (it does not send any group-specific or group-and-source queries before deleting the entry).
• Disable snooping on a VLAN.
Specifying a Port as Connected to a Multicast Router To statically specify or view a port in a VLAN, use the following commands. • Statically specify a port in a VLAN as connected to a multicast router. INTERFACE VLAN mode ip igmp snooping mrouter • View the ports that are connected to multicast routers. EXEC Privilege mode. show ip igmp snooping mrouter Configuring the Switch as Querier To configure the switch as a querier, use the following command.
Fast Convergence after MSTP Topology Changes When a port transitions to the Forwarding state as a result of an STP or MSTP topology change, Dell EMC Networking OS sends a general query out of all ports except the multicast router ports. The host sends a response to the general query and the forwarding database is updated without having to wait for the query interval to expire.
Table 19.
When the feature is enabled using the management egress-interface-selection command, the following events are performed: • The CLI prompt changes to the EIS mode. • In this mode, you can run the application and no application commands • Applications can be configured or unconfigured as management applications using the application or no application command. All configured applications are considered as management applications and the rest of them as non-management applications.
Handling of Switch-Initiated Traffic When the control processor (CP) initiates a control packet, the following processing occurs: • TCP/UDP port number is extracted from the sockaddr structure in the in_selectsrc call which is called as part of the connect system call or in the ip_output function.
• If route lookup in the EIS routing table fails or if the management port is down, then packets are dropped. The management application drop counter is incremented. • Whenever IP address is assigned to the management port, it is stored in a global variable in the IP stack, which is used for comparison with the source IP address of the packet. • Rest of the response traffic is handled as per existing behavior by doing route lookup in the default routing table.
Traffic type / Application type Switch initiated traffic Switch-destined traffic only. No change in the existing behavior.
Table 21.
Table 22.
• Designate an interface as a multicast router interface.
19 Interfaces This chapter describes interface types, both physical and logical, and how to configure them with Dell EMC Networking Operating System (OS). The system supports 1 Gigabit Ethernet and 10 Gigabit Ethernet interfaces.
• Egress Interface Selection (EIS) • Management Interfaces • VLAN Interfaces • Loopback Interfaces • Null Interfaces • Port Channel Interfaces • Bulk Configuration • Defining Interface Range Macros • Monitoring and Maintaining Interfaces • Link Dampening • Link Bundle Monitoring • Using Ethernet Pause Frames for Flow Control • Configure the MTU Size on an Interface • Port-Pipes • Auto-Negotiation on Ethernet Interfaces • Provisioning Combo Ports • View Advanced Interface Inf
View Basic Interface Information To view basic interface information, use the following command. You have several options for viewing interface status and configuration parameters. • Lists all configurable interfaces on the chassis. EXEC mode show interfaces This command has options to display the interface status, IP and MAC addresses, and multiple counters for the amount and type of traffic passing through the interface.
GigabitEthernet GigabitEthernet GigabitEthernet GigabitEthernet GigabitEthernet GigabitEthernet GigabitEthernet GigabitEthernet GigabitEthernet 1/1 1/2 1/3 1/4 1/5 1/6 1/7 1/8 1/9 unassigned unassigned unassigned unassigned unassigned 10.10.10.
Enabling Energy Efficient Ethernet Energy Efficient Ethernet (EEE) is an IEEE 802.3 az standard that reduces power consumptions on Ethernet ports. EEE stops the transmission when there is no data to be transmitted and resumes the transmission at the arrival of new packets. You can enable EEE only on one Gigabit and ten Gigabit native or optional module copper ports. 1 To enable EEE, use the eee command.
show hardware counters interface-type slot/port show hardware stack-unit stack-unit-number unit unit-number counters Examples of the show Commands The following example shows the status information for all the interfaces.
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX 326 - Unicast Packet Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame Counter 256 to 511 Byte Frame Counter 512 to 1023 Byte Frame Counter 1024 to 1518 Byte Frame Counter 1519 to 1522 Byte Good VLAN Frame Counter 1519 to 2047 Byte Frame Counter 2048 to 4095 Byte Frame C
TX - RUNT Frame Counter TX - Fragment Counter TX - PFC Frame Priority 0 TX - PFC Frame Priority 1 TX - PFC Frame Priority 2 TX - PFC Frame Priority 3 TX - PFC Frame Priority 4 TX - PFC Frame Priority 5 TX - PFC Frame Priority 6 TX - PFC Frame Priority 7 TX - Debug Counter 0 TX - Debug Counter 1 TX - Debug Counter 2 TX - Debug Counter 3 TX - Debug Counter 4 TX - Debug Counter 5 TX - Debug Counter 6 TX - Debug Counter 7 TX - Debug Counter 8 TX - Debug Counter 9 TX - Debug Counter 10 TX - Debug Counter 11 TX -
RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - PFC Frame Priority 5 PFC Frame Priority 6 PFC Frame Priority 7 Debug Counter 0 Debug Counter 1 Debug Counter 2 Debug Counter 3 Debug Counter 4 Debug Counter 5 Debug Counter 6 Debug Counter 7 Debug Counter 8 EEE LPI Event Counter EEE LPI Duration Counter 64 Byte Frame Counter 65 to 127 Byte Frame Counter 128 to 255 Byte Frame C
EXEC Privilege mode • clear counters eee Clear the EEE counters on the specified port. EXEC Privilege mode • clear counters interface-type slot/port eee Clear the EEE counters on the specified range of ports. EXEC Privilege mode clear counters interface-type slot/port-range eee Examples of the clear counters eee Command When you use this command, confirm that you want Dell EMC Networking OS to clear the EEE counters.
Configuration Task List for Physical Interfaces By default, all interfaces are operationally disabled and traffic does not pass through them.
Example of a Basic Layer 2 Interface Configuration DellEMC(conf-if)#show config ! interface Port-channel 1 no ip address switchport no shutdown DellEMC(conf-if)# Configuring Layer 2 (Interface) Mode To configure an interface in Layer 2 mode, use the following commands. • Enable the interface. INTERFACE mode no shutdown • Place the interface in Layer 2 (switching) mode. INTERFACE mode switchport To view the interfaces in Layer 2 mode, use the show interfaces switchport command in EXEC mode.
To determine the configuration of an interface, use the show config command in INTERFACE mode or the various show interface commands in EXEC mode. Configuring Layer 3 (Interface) Mode To assign an IP address, use the following commands. • Enable the interface. INTERFACE mode • no shutdown Configure a primary IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] The ip-address must be in dotted-decimal format (A.B.C.D) and the mask must be in slash format (/xx).
• If a route in the EIS table conflicts with a front-end port route, the front-end port route has precedence. • Due to protocol, ARP packets received through the management port create two ARP entries (one for the lookup in the EIS table and one for the default routing table). Configuring EIS EIS is compatible with the following protocols: DNS, FTP, NTP, RADIUS, sFlow, SNMP, SSH, Syslog, TACACS, Telnet, and TFTP. To enable and configure EIS, use the following commands: 1 Enter EIS mode.
Viewing Two Global IPv6 Addresses Important Points to Remember — virtual-ip You can configure two global IPv6 addresses on the system in EXEC Privilege mode. To view the addresses, use the show interface managementethernet command, as shown in the following example. If you try to configure a third IPv6 address, an error message displays. If you enable auto-configuration, all IPv6 addresses on that management interface are auto-configured.
To view the Primary RPM Management port, use the show interface Managementethernet command in EXEC Privilege mode. If there are two RPMs, you cannot view information on that interface. Configuring a Management Interface on an Ethernet Port You can manage the system through any port using remote access such as Telnet. To configure an IP address for the port, use the following commands. There is no separate management routing table, so configure all routes in the IP routing table (the ip route command).
Example of a Configuration for a VLAN Participating in an OSPF Process interface Vlan 10 ip address 1.1.1.2/24 tagged GigabitEthernet 2/2-2/13 tagged GigabitEthernet 5/1 ip ospf authentication-key force10 ip ospf cost 1 ip ospf dead-interval 60 ip ospf hello-interval 15 no shutdown ! Loopback Interfaces A Loopback interface is a virtual interface in which the software emulates an interface. Packets routed to it are processed locally.
• Port Channel Implementation • Configuration Tasks for Port Channel Interfaces Port Channel Definition and Standards Link aggregation is defined by IEEE 802.3ad as a method of grouping multiple physical interfaces into a single logical interface—a link aggregation group (LAG) or port channel. A LAG is “a group of links that appear to a MAC client as if they were a single link” according to IEEE 802.3ad. In Dell EMC Networking OS, a LAG is referred to as a port channel interface.
Interfaces in Port Channels When interfaces are added to a port channel, the interfaces must share a common speed. When interfaces have a configured speed different from the port channel speed, the software disables those interfaces. The common speed is determined when the port channel is first enabled. Then, the software checks the first interface listed in the port channel configuration. If you enabled that interface, its speed configuration becomes the common speed of the port channel.
You can configure a port channel as you would a physical interface by enabling or configuring protocols or assigning access control lists. Adding a Physical Interface to a Port Channel The physical interfaces in a port channel can be on any line card in the chassis, but must be the same physical type.
Hardware address is 00:01:e8:01:46:fa Internet address is 1.1.120.
interface port-channel id number 3 Add the interface to the second port channel. INTERFACE PORT-CHANNEL mode channel-member interface Example of Moving an Interface to a New Port Channel The following example shows moving an interface from port channel 4 to port channel 3.
• Add the port channel to the VLAN as an untagged interface. INTERFACE VLAN mode untagged port-channel id number • An interface without tagging enabled can belong to only one VLAN. Remove the port channel with tagging enabled from the VLAN. INTERFACE VLAN mode no tagged port-channel id number or no untagged port-channel id number • Identify which port channels are members of VLANs.
• Configure an IP address and mask on the interface. INTERFACE mode ip address ip-address mask [secondary] • ip-address mask: enter an address in dotted-decimal format (A.B.C.D). The mask must be in slash format (/24). • secondary: the IP address is the interface’s backup IP address. You can configure up to eight secondary IP addresses. Deleting or Disabling a Port Channel To delete or disable a port channel, use the following commands. • Delete a port channel.
• mac [dest-mac | source-dest-mac | source-mac] — Distribute IPV4 traffic based on the destination or source MAC address, or both, along with the VLAN, Ethertype, source module ID and source port ID. • tcp-udp enable — Distribute traffic based on the TCP/UDP source and destination ports. • ingress-port — Option to Source Port Id for ECMP/ LAG hashing. • ipv6-selection— Set the IPV6 key fields to use in hash computation. • tunnel— Set the tunnel key fields to use in hash computation.
• crc32MSB — uses MSB 16 bits of computed CRC32(default) • crc-upper — uses the upper 32 bits of the hash key to compute the egress port. • dest-ip — uses destination IP address as part of the hash key. • lsb — uses the least significant bit of the hash key to compute the egress port.
• Overlap Port Ranges • Commas • Add Ranges Create a Single-Range The following is an example of a single range. Example of the interface range Command (Single Range) DellEMC(config)# interface range gigabitethernet 1/1 - 1/23 DellEMC(config-if-range-gi-1/1-1/23)# no shutdown DellEMC(config-if-range-gi-1/1-1/23)# Create a Multiple-Range The following is an example of multiple range.
Commas The following is an example of how to use commas to add different interface types to a range of interfaces. Example of Adding Interface Ranges DellEMC(config-if)# interface range gigabitethernet 5/1 - 23, gigabitethernet 1/1 - 1/2 DellEMC(config-if-range-gi-5/1-23,gi1/1-1/2)# no shutdown DellEMC(config-if-range-gi-5/1-23,gi1/1-1/2)# Add Ranges The following example shows how to use commas to add VLAN and port-channel interfaces to the range.
Monitoring and Maintaining Interfaces Monitor interface statistics with the monitor interface command. This command displays an ongoing list of the interface status (up/ down), number of packets, traffic statistics, and so on. To view the interface’s statistics, use the following command. • View the interface’s statistics. EXEC Privilege mode Enter the type of interface and the interface information: • For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
Maintenance Using TDR The time domain reflectometer (TDR) is supported on all Dell EMC Networking switches. TDR is an assistance tool to resolve link issues that helps detect obvious open or short conditions within any of the four copper pairs. TDR sends a signal onto the physical cable and examines the reflection of the signal that returns. By examining the reflection, TDR is able to indicate whether there is a cable fault (when the cable is broken, becomes unterminated, or if a transceiver is unplugged).
• reuse-threshold— After exponential decay, the penalty reaches the default or configured reuse threshold. The interface is unsuppressed and the state changes to “up”. The range of reuse threshold is from 1 to 20000. The default is 750. • max-suppress-time— The maximum amount of time during which the interface remain suppressed. The range is from 1 to 86400. The default is 20 seconds or four times the default half-life period (5 seconds).
Figure 38. Interface State Change When an interface periodically flaps as shown above. Every time the interface goes down, a penalty is added. When the accumulated penalty exceeds the configured suppress threshold (2400), the interface state is set to Error-Disabled state. When the interface becomes stable, the penalty will exponentially decay based on the set half-life (10 seconds).
1200 and in second half-life, the penalty decays to 600 and so on. When the penalty decays below the set reuse threshold (300), the interface is unsuppressed and the interface state changes to “up” state. Enabling Link Dampening To enable link dampening, use the following command. • Enable link dampening. INTERFACE mode dampening Examples of the show interfaces dampening Commands To view the link dampening configuration on an interface, use the show config command.
Link Dampening Support for XML View the output of the following show commands in XML by adding | display xml to the end of the command. • show interfaces dampening • show interfaces dampening summary • show interfaces interface slot/port Configure MTU Size on an Interface In Dell EMC Networking OS, Maximum Transmission Unit (MTU) is defined as the entire Ethernet packet (Ethernet header + FCS + payload). The link MTU is the frame size of a packet, and the IP MTU size is used for IP fragmentation.
link-bundle-distribution trigger-threshold DellEMC(conf)#link-bundle-distribution trigger-threshold • View the link bundle monitoring status. show link-bundle-distribution Using Ethernet Pause Frames for Flow Control Ethernet pause frames and threshold settings are supported on the Dell EMC Networking OS. Ethernet Pause Frames allow for a temporary stop in data transmission. A situation may arise where a sending device may transmit data faster than a destination device can accept it.
The flow control sender and receiver must be on the same port-pipe. Flow control is not supported across different port-pipes. To enable pause frames, use the following command. • Control how the system responds to and generates 802.3x pause frames on the Ethernet ports. INTERFACE mode flowcontrol {rx [off | on] tx [off | on] [negotiate] } • rx on: enter the keywords rx on to process the received flow control frames on this port.
For example, the VLAN contains tagged members with Link MTU of 1522 and IP MTU of 1500 and untagged members with Link MTU of 1518 and IP MTU of 1500. The VLAN’s Link MTU cannot be higher than 1518 bytes and its IP MTU cannot be higher than 1500 bytes. Port-Pipes A port pipe is a Dell EMC Networking-specific term for the hardware packet-processing elements that handle network traffic to and from a set of front-end I/O ports. The physical, front-end I/O ports are referred to as a port-set.
speed {10 | 100 | 1000 | 10000 | auto} NOTE: If you use an active optical cable (AOC), you can convert the QSFP+ port to a 10 Gigabit SFP+ port or 1 Gigabit SFP port. You can use the speed command to enable the required speed. 6 Disable auto-negotiation on the port. INTERFACE mode no negotiation auto If the speed was set to 1000, do not disable auto-negotiation. 7 Verify configuration changes.
DellEMC(conf-if-gi-1/1)#speed 100 DellEMC(conf-if-gi-1/1)#duplex full DellEMC(conf-if-gi-1/1)#no negotiation auto DellEMC(conf-if-gi-1/1)#show config ! interface GigabitEthernet 1/1 no ip address speed 100 duplex full no shutdown Set Auto-Negotiation Options The negotiation auto command provides a mode option for configuring an individual port to forced master/ forced slave once autonegotiation is enabled.
Provisioning Combo Ports The device has two combo ports of 1G SFP. By default, the combo ports are in Hybrid mode. You can provision the combo ports to act as a copper or fiber medium. The speed and negotiation auto commands are not available on the combo ports in the Hybrid mode. To apply these commands on combo ports, provision the ports as individual medium. You can use the combo-port-type command to provision the combo ports as copper or fiber medium.
Vlan membership: Vlan 2 Name: GigabitEthernet 3/2 802.1QTagged: True Vlan membership: Vlan 2 Name: GigabitEthernet 3/3 802.1QTagged: True Vlan membership: Vlan 2 Name: GigabitEthernet 3/4 802.1QTagged: True Vlan membership: Vlan 2 --More-- Configuring the Interface Sampling Size Although you can enter any value between 30 and 299 seconds (the default), software polling is done once every 15 seconds. So, for example, if you enter “19”, you actually get a sample of the past 15 seconds.
DellEMC#show interfaces GigabitEthernet 1/1 is down, line protocol is down Hardware is DellEMCEth, address is 00:01:e8:01:9e:d9 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 10000 Mbit ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 1d23h45m Queueing strategy: fifo 0 packets input, 0 bytes Input 0 IP Packets, 0 Vlans 0 MPLS 0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts Rece
3106 packets, 226755 bytes 133 64-byte pkts, 2973 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 406 Multicasts, 0 Broadcasts, 2700 Unicasts 0 runts, 0 giants, 0 throttles 0 CRC, 0 overrun, 0 discarded Output Statistics: 3106 packets, 226755 bytes, 0 underruns 133 64-byte pkts, 2973 over 64-byte pkts, 0 over 127-byte pkts 0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 406 Multicasts, 0 Broadcasts, 2700 Unicasts 0 throttles, 0 disc
• Egress ACLs • ILM • IP FLOW • IP ACL • IP FIB • L2 ACL • L2 FIB Clearing Interface Counters The counters in the show interfaces command are reset by the clear counters command. This command does not clear the counters any SNMP program captures. To clear the counters, use the following the command. • Clear the counters used in the show interface commands for all VRRP groups, VLANs, and physical interfaces or selected ones.
20 Internet Protocol Security (IPSec) Internet protocol security (IPSec) is an end-to-end security scheme for protecting IP communications by authenticating and encrypting all packets in a communication session. Use IPSec between hosts, between gateways, or between hosts and gateways. IPSec is compatible with Telnet and FTP protocols. It supports two operational modes: Transport and Tunnel. • Transport mode — (default) Use to encrypt only the payload of the packet. Routing information is unchanged.
crypto ipsec policy myCryptoPolicy 10 ipsec-manual transform-set myXform-set session-key inbound esp 256 auth encrypt session-key outbound esp 257 auth encrypt match 0 tcp a::1 /128 0 a::2 /128 23 match 1 tcp a::1 /128 23 a::2 /128 0 match 2 tcp a::1 /128 0 a::2 /128 21 match 3 tcp a::1 /128 21 a::2 /128 0 match 4 tcp 1.1.1.1 /32 0 1.1.1.2 /32 23 match 5 tcp 1.1.1.1 /32 23 1.1.1.2 /32 0 match 6 tcp 1.1.1.1 /32 0 1.1.1.2 /32 21 match 7 tcp 1.1.1.1 /32 21 1.1.1.
21 IPv4 Routing The Dell EMC Networking Operating System (OS) supports various IP addressing features. This chapter describes the basics of domain name service (DNS), address resolution protocol (ARP), and routing principles and their implementation in the Dell EMC Networking OS.
• Configuring a Broadcast Address • Configurations Using UDP Helper • UDP Helper with Broadcast-All Addresses • UDP Helper with Subnet Broadcast Addresses • UDP Helper with Configured Broadcast Addresses • UDP Helper with No Configured Broadcast Addresses • Troubleshooting UDP Helper IP Addresses Dell EMC Networking OS supports IP version 4 (as described in RFC 791), classful routing, and variable length subnet masks (VLSM). With VLSM, you can configure one network with different masks.
2 • For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For the Management interface on the stack-unit, enter the keyword ManagementEthernet then the slot/port information. • For a port channel interface, enter the keywords port-channel then a number.
• permanent: keep the static route in the routing table (if you use the interface option) even if you disable the interface with the route. (optional) • tag tag-value: the range is from 1 to 4294967295. (optional) Example of the show ip route static Command To view the configured routes, use the show ip route static command. DellEMC#show ip route static Destination Gateway ----------------S 2.1.2.0/24 Direct, Nu 0 S 6.1.2.0/24 via 6.1.20.2, S 6.1.2.2/32 via 6.1.20.2, S 6.1.2.3/32 via 6.1.20.2, S 6.1.2.
10.16.0.0/16 172.16.1.0/24 ManagementEthernet 1/1 10.16.151.4 Connected Active Connected Static IPv4 Path MTU Discovery Overview The size of the packet that can be sent across each hop in the network path without being fragmented is called the path maximum transmission unit (PMTU). This value might vary for the same route between two devices, mainly over a public network, depending on the network load and speed, and it is not a consistent value.
Configuring the Duration to Establish a TCP Connection You can configure the duration for which the device must wait before it attempts to establish a TCP connection. Using this capability, you can limit the wait times for TCP connection requests.
The following sections describe DNS and the resolution of host names. • Enabling Dynamic Resolution of Host Names • Specifying the Local System Domain and a List of Domains • Configuring DNS with Traceroute Name server, Domain name, and Domain list are VRF specific. The maximum number of Name servers and Domain lists per VRF is six. Enabling Dynamic Resolution of Host Names By default, dynamic resolution of host names (DNS) is disabled. To enable DNS, use the following commands.
ip domain-list name Configure this command up to six times to specify a list of possible domain names. Dell EMC Networking OS searches the domain names in the order they were configured until a match is found or the list is exhausted. Configuring DNS with Traceroute To configure your switch to perform DNS with traceroute, use the following commands. • Enable dynamic resolution of host names. CONFIGURATION mode ip domain-lookup • Specify up to six name servers.
For more information about Proxy ARP, refer to RFC 925, Multi-LAN Address Resolution, and RFC 1027, Using ARP to Implement Transparent Subnet Gateways. Configuration Tasks for ARP For a complete listing of all ARP-related commands, refer to the Dell EMC Networking OS Command Line Reference Guide.
Clearing ARP Cache To clear the ARP cache of dynamically learnt ARP information, use the following command. • Clear the ARP caches for all interfaces or for a specific interface by entering the following information. EXEC privilege clear arp-cache [interface | ip ip-address] [no-refresh] • ip ip-address (OPTIONAL): enter the keyword ip then the IP address of the ARP entry you wish to clear. • no-refresh (OPTIONAL): enter the keywords no-refresh to delete the ARP entry from CAM.
Figure 39. ARP Learning via ARP Request Beginning with Dell EMC Networking OS version 8.3.1.0, when you enable ARP learning via gratuitous ARP, the system installs a new ARP entry, or updates an existing entry for all received ARP requests. Figure 40. ARP Learning via ARP Request with ARP Learning via Gratuitous ARP Enabled Whether you enable or disable ARP learning via gratuitous ARP, the system does not look up the target IP.
CONFIGURATION mode arp backoff-time The default is 30. • The range is from 1 to 3600. Display all ARP entries learned via gratuitous ARP. EXEC Privilege mode show arp retries ICMP For diagnostics, the internet control message protocol (ICMP) provides routing information to end stations by choosing the best route (ICMP redirect messages) or determining if a router is reachable (ICMP Echo or Echo Reply). ICMP error messages inform the router of problems in a particular packet.
Important Points to Remember • The existing ip directed broadcast command is rendered meaningless if you enable UDP helper on the same interface. • The broadcast traffic rate should not exceed 200 packets per second when you enable UDP helper. • You may specify a maximum of 16 UDP ports.
Internet address is 1.1.0.1/24 IP UDP-Broadcast address is 1.1.255.
Figure 41. UDP Helper with Broadcast-All Addresses UDP Helper with Subnet Broadcast Addresses When the destination IP address of an incoming packet matches the subnet broadcast address of any interface, the system changes the address to the configured broadcast address and sends it to matching interface. In the following illustration, Packet 1 has the destination IP address 1.1.1.255, which matches the subnet broadcast address of VLAN 101.
Figure 43. UDP Helper with Configured Broadcast Addresses UDP Helper with No Configured Broadcast Addresses The following describes UDP helper with no broadcast addresses configured. • If the incoming packet has a broadcast destination IP address, the unaltered packet is routed to all Layer 3 interfaces. • If the Incoming packet has a destination IP address that matches the subnet broadcast address of any interface, the unaltered packet is routed to the matching interfaces.
22 IPv6 Routing Internet protocol version 6 (IPv6) routing is the successor to IPv4. Due to the rapid growth in internet users and IP addresses, IPv4 is reaching its maximum usage. IPv6 will eventually replace IPv4 usage to allow for the constant expansion. This chapter provides a brief description of the differences between IPv4 and IPv6, and the Dell EMC Networking support of IPv6. This chapter is not intended to be a comprehensive description of IPv6.
Extended Address Space The address format is extended from 32 bits to 128 bits. This not only provides room for all anticipated needs, it allows for the use of a hierarchical address space structure to optimize global addressing. Stateless Autoconfiguration When a booting device comes up in IPv6 and asks for its network prefix, the device can get the prefix (or prefixes) from an IPv6 router on its link.
• Flow Label (20 bits) • Payload Length (16 bits) • Next Header (8 bits) • Hop Limit (8 bits) • Source Address (128 bits) • Destination Address (128 bits) IPv6 provides for extension headers. Extension headers are used only if necessary. There can be no extension headers, one extension header or more than one extension header in an IPv6 packet. Extension headers are defined in the Next Header field of the preceding IPv6 header.
Next Header (8 bits) The Next Header field identifies the next header’s type. If an Extension header is used, this field contains the type of Extension header (as shown in the following table). If the next header is a transmission control protocol (TCP) or user datagram protocol (UDP) header, the value in this field is the same as for IPv4. The Extension header is located between the IP header and the TCP or UDP header. The following lists the Next Header field values.
Source Address (128 bits) The Source Address field contains the IPv6 address for the packet originator. Destination Address (128 bits) The Destination Address field contains the intended recipient’s IPv6 address. This can be either the ultimate destination or the address of the next hop router. Extension Header Fields Extension headers are used only when necessary. Due to the streamlined nature of the IPv6 header, adding extension headers do not severely impact performance.
10 Discard the packet and send an ICMP Parameter Problem Code 2 message to the packet’s Source IP Address identifying the unknown option type. 11 Discard the packet and send an ICMP Parameter Problem, Code 2 message to the packet’s Source IP Address only if the Destination IP Address is not a multicast address. The second byte contains the Option Data Length. The third byte specifies whether the information can change en route to the destination.
the same IPv6 address to a particular computer, and never to assign that IP address to another computer. This allows static IPv6 addresses to be configured in one place, without having to specifically configure each computer on the network in a different way. In IPv6, every interface, whether using static or dynamic address assignments, also receives a local-link address automatically in the fe80::/64 subnet.
Feature and Functionality Dell EMC Networking OS Release Introduction Documentation and Chapter Location S3100 series IS-IS for IPv6 support for redistribution 9.7.(0.1) Intermediate System to Intermediate System IPv6 IS-IS in the Dell EMC Networking OS Command Line Reference Guide. ISIS for IPv6 support for distribute lists and administrative distance 9.7.(0.1) OSPF for IPv6 (OSPFv3) 9.7.(0.1) Equal Cost Multipath for IPv6 9.7.(0.
• Error reporting messages indicate when the forwarding or delivery of the packet failed at the destination or intermediate node. These messages include Destination Unreachable, Packet Too Big, Time Exceeded and Parameter Problem messages. • Informational messages provide diagnostic functions and additional host functions, such as Neighbor Discovery and Multicast Listener Discovery. These messages also include Echo Request and Echo Reply messages.
With ARP, each node broadcasts ARP requests on the entire link. This approach causes unnecessary processing by uninterested nodes. With NDP, each node sends a request only to the intended destination via a multicast address with the unicast address used as the last 24 bits. Other hosts on the link do not participate in the process, greatly increasing network bandwidth efficiency. Figure 46.
The DNS server address does not allow the following: • link local addresses • loopback addresses • prefix addresses • multicast addresses • invalid host addresses If you specify this information in the IPv6 RDNSS configuration, a DNS error is displayed. Example for Configuring an IPv6 Recursive DNS Server The following example configures a RDNNS server with an IPv6 address of 1000::1 and a lifetime of 1 second.
Displaying IPv6 RDNSS Information To display IPv6 interface information, including IPv6 RDNSS information, use the show ipv6 interface command in EXEC or EXEC Privilege mode. Examples of Displaying IPv6 RDNSS Information The following example displays IPv6 RDNSS information. The output in the last 3 lines indicates that the IPv6 RDNSS was correctly configured on interface te 1/1.
Configuration Tasks for IPv6 The following are configuration tasks for the IPv6 protocol. • Adjusting Your CAM-Profile • Assigning an IPv6 Address to an Interface • Assigning a Static IPv6 Route • Configuring Telnet with IPv6 • SNMP over IPv6 • Showing IPv6 Information • Clearing IPv6 Routes Adjusting Your CAM-Profile Although adjusting your CAM-profile is not a mandatory step, if you plan to implement IPv6 ACLs, adjust your CAM settings. The CAM space is allotted in FP blocks.
The total number of groups is 4. Assigning an IPv6 Address to an Interface Essentially, IPv6 is enabled in Dell EMC Networking OS simply by assigning IPv6 addresses to individual router interfaces. You can use IPv6 and IPv4 together on a system, but be sure to differentiate that usage carefully. To assign an IPv6 address to an interface, use the ipv6 address command.
Configuring Telnet with IPv6 The Telnet client and server in Dell EMC Networking OS supports IPv6 connections. You can establish a Telnet session directly to the router using an IPv6 Telnet client, or you can initiate an IPv6 Telnet connection from the router. NOTE: Telnet to link local addresses is supported on the system. • Enter the IPv6 Address for the device. EXEC mode or EXEC Privileged mode telnet [vrf vrf-name] ipv6 address • ipv6 address: x:x:x:x::x • mask: prefix length is from 0 to 128.
prefix-list route rpf DellEMC# List IPv6 prefix lists IPv6 routing information RPF table Displaying an IPv6 Interface Information To view the IPv6 configuration for a specific interface, use the following command. • Show the currently running configuration for the specified interface. EXEC mode show ipv6 interface interface {slot/port} Enter the keyword interface then the type of interface and slot/port information: • For all brief summary of IPv6 status and configuration, enter the keyword brief.
show ipv6 route [vrf vrf-name] type The following keywords are available: • To display information about a network, enter ipv6 address (X:X:X:X::X). • To display information about a host, enter hostname. • To display information about all IPv6 routes (including non-active routes), enter all. • To display information about all connected IPv6 routes, enter connected. • To display information about brief summary of all IPv6 routes, enter summary.
Showing the Running-Configuration for an Interface To view the configuration for any interface, use the following command. • Show the currently running configuration for the specified interface. EXEC mode show running-config interface type {slot/port} Enter the keyword interface then the type of interface and slot/port information: • For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information.
no ipv6 nd disable-reachable-timer The following example shows how to disable the ND timer. DellEMC(conf-if-fo-1/1/1)#ipv6 nd disable-reachable-timer Configuring IPv6 RA Guard The IPv6 Router Advertisement (RA) guard allows you to block or reject the unwanted router advertisement guard messages that arrive at the network device platform. To configure the IPv6 RA guard, perform the following steps: 1 Configure the terminal to enter the Global Configuration mode.
10 Set the router lifetime. POLICY LIST CONFIGURATION mode router—lifetime value The router lifetime range is from 0 to 9,000 seconds. 11 Apply the policy to trusted ports. POLICY LIST CONFIGURATION mode trusted-port 12 Set the maximum transmission unit (MTU) value. POLICY LIST CONFIGURATION mode mtu value 13 Set the advertised reachability time. POLICY LIST CONFIGURATION mode reachable—time value The reachability time range is from 0 to 3,600,000 milliseconds.
INTERFACE mode ipv6 nd ra-guard attach policy policy-name [vlan [vlan 1, vland 2, vlan 3.....]] 3 Display the configurations applied on all the RA guard policies or a specific RA guard policy. EXEC Privilege mode show ipv6 nd ra-guard policy policy-name The policy name string can be up to 140 characters. Example of the show ipv6 nd ra-guard policy Command Monitoring IPv6 RA Guard To debug IPv6 RA guard, use the following command.
23 iSCSI Optimization This chapter describes how to configure internet small computer system interface (iSCSI) optimization, which enables quality-of-service (QoS) treatment for iSCSI traffic.
NOTE: After a switch is reloaded, powercycled, or upgraded, any information exchanged during the initial handshake is not available. If the switch establishes communication after reloading, it detects that a session was in progress but could not obtain complete information for it. Any incomplete information is not available in the show commands.
Monitoring iSCSI Traffic Flows The switch snoops iSCSI session-establishment and termination packets by installing classifier rules that trap iSCSI protocol packets to the CPU for examination. Devices that initiate iSCSI sessions usually use well-known TCP ports 3260 or 860 to contact targets. When you enable iSCSI optimization, by default the switch identifies IP packets to or from these ports as iSCSI traffic.
NOTE: If you are using EqualLogic or Compellent storage arrays, more than 256 simultaneous iSCSI sessions are possible. However, iSCSI session monitoring is not capable of monitoring more than 256 simultaneous iSCSI sessions. If this number is exceeded, sessions may display as unknown in session monitoring output. Dell EMC Networking recommends that you disable iSCSI session monitoring for EqualLogic and Compellent storage arrays or for installations with more than 256 simultaneous iSCSI sessions.
• Jumbo frame size is set to the maximum for all interfaces on all ports and port-channels, if it is not already enabled. • Spanning-tree portfast is enabled on the interface. • Unicast storm control is disabled on the interface. Enter the iscsi profile-compellent command in INTERFACE Configuration mode. Synchronizing iSCSI Sessions Learned on VLT-Lags with VLTPeer The following behavior occurs during synchronization of iSCSI sessions.
Default iSCSI Optimization Values The following table lists the default values for the iSCSI optimization feature. Table 28. iSCSI Optimization Defaults Parameter Default Value iSCSI Optimization global setting Disabled on the S4810, S4820T, S3048–ON, S4048–ON, and S3100 series. iSCSI CoS mode (802.1p priority queue mapping) dot1p priority 4 without the remark setting when you enable iSCSI. If you do not enable iSCSI, this feature is disabled.
NOTE: Content addressable memory (CAM) allocation is optional. If CAM is not allocated, the following features are disabled: • session monitoring • aging • class of service You can enable iSCSI even when allocated with zero (0) CAM blocks. However, if no CAM blocks are allocated, session monitoring is disabled and this information the show iscsi command displays this information. 2 Enable iSCSI. CONFIGURATION mode iscsi enable 3 For a DCB environment: Configure DCB and iSCSI.
• dot1p vlan-priority-value: specifies the virtual local area network (VLAN) priority tag assigned to incoming packets in an iSCSI session. The range is from 0 to 7. The default is: the dot1p value in ingress iSCSI frames is not changed and the same priority is used in iSCSI TLV advertisements if you do not enter the iscsi priority-bits command (Step 10). • dscp dscp-value: specifies the DSCP value assigned to incoming packets in an iSCSI session. The range is from 0 to 63.
The following example shows the show iscsi session command. VLT PEER1 DellEMC#show iscsi session Session 0: ----------------------------------------------------------------------------------Target: iqn.2001-05.com.equallogic:0-8a0906-0e70c2002-10a0018426a48c94-iom010 Initiator: iqn.1991-05.com.microsoft:win-x9l8v27yajg ISID: 400001370000 VLT PEER2 Session 0: -----------------------------------------------------------------------------------Target: iqn.2001-05.com.
24 Intermediate System to Intermediate System The intermediate system to intermediate system (IS-IS) protocol that uses a shortest-path-first algorithm. Dell EMC Networking supports both IPv4 and IPv6 versions of IS-IS.
• area address — within your routing domain or area, each area must have a unique area value. The first byte is called the authority and format indicator (AFI). • system address — the router’s MAC address. • N-selector — this is always 0. The following illustration is an example of the ISO-style address to show the address format IS-IS uses. In this example, the first five bytes (47.0005.0001) are the area address. The system portion is 000c.000a.4321 and the last byte is always 0. Figure 48.
Interface Support MT IS-IS is supported on physical Ethernet interfaces, physical synchronous optical network technologies (SONET) interfaces, portchannel interfaces (static and dynamic using LACP), and virtual local area network (VLAN) interfaces. Adjacencies Adjacencies on point-to-point interfaces are formed as usual, where IS-IS routers do not implement MT extensions.
IPv6 Reachability and IPv6 Interface Address. Also, a new IPv6 protocol identifier has also been included in the supported TLVs. The new TLVs use the extended metrics and up/down bit semantics. Multi-topology IS-IS adds TLVs: • MT TLV — contains one or more Multi-Topology IDs in which the router participates. This TLV is included in IIH and the first fragment of an LSP. • MT Intermediate Systems TLV — appears for every topology a node supports.
Configuration Tasks for IS-IS The following describes the configuration tasks for IS-IS. • Enabling IS-IS • Configure Multi-Topology IS-IS (MT IS-IS) • Configuring IS-IS Graceful Restart • Changing LSP Attributes • Configuring the IS-IS Metric Style • Configuring IS-IS Cost • Changing the IS-Type • Controlling Routing Updates • Configuring Authentication Passwords • Setting the Overload Bit • Debugging IS-IS Enabling IS-IS By default, IS-IS is not enabled.
4 • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383. • For a port channel interface, enter the keywords port-channel then a number. • For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Enter an IPv4 Address. INTERFACE mode ip address ip-address mask Assign an IP address and mask to the interface.
Accept wide metrics: DellEMC# none To view IS-IS protocol statistics, use the show isis traffic command in EXEC Privilege mode.
4 Implement a wide metric-style globally. ROUTER ISIS AF IPV6 mode isis ipv6 metric metric-value [level-1 | level-2 | level-1-2] To configure wide or wide transition metric style, the cost can be between 0 and 16,777,215. Configuring IS-IS Graceful Restart To enable IS-IS graceful restart globally, use the following commands. Additionally, you can implement optional commands to enable the graceful restart settings. • Enable graceful restart on ISIS processes.
• adjacency: the restarting router receives the remaining time value from its peer and adjusts its T3 value so if user has configured this option. • manual: allows you to specify a fixed value that the restarting router should use. The range is from 50 to 120 seconds. The default is 30 seconds. Examples of the show isis graceful-restart detail Command NOTE: If this timer expires before the synchronization has completed, the restarting router sends the overload bit in the LSP.
LSP Interval: 33 Next IS-IS LAN Level-1 Hello in 4 seconds Next IS-IS LAN Level-2 Hello in 6 seconds LSP Interval: 33 Restart Capable Neighbors: 2, In Start: 0, In Restart: 0 DellEMC# Changing LSP Attributes IS-IS routers flood link state PDUs (LSPs) to exchange routing information. LSP attributes include the generation interval, maximum transmission unit (MTU) or size, and the refresh interval. You can modify the LSP attribute defaults, but it is not necessary.
Configuring the IS-IS Metric Style All IS-IS links or interfaces are associated with a cost that is used in the shortest path first (SPF) calculations. The possible cost varies depending on the metric style supported. If you configure narrow, transition, or narrow transition metric style, the cost can be a number between 0 and 63. If you configure wide or wide transition metric style, the cost can be a number between 0 and 16,777,215.
Distance: 115 Generate narrow metrics: Accept narrow metrics: Generate wide metrics: Accept wide metrics: DellEMC# level-1-2 level-1-2 none none Configuring the IS-IS Cost When you change from one IS-IS metric style to another, the IS-IS metric value could be affected. For each interface with IS-IS enabled, you can assign a cost or metric that is used in the link state calculation. To change the metric or cost of the interface, use the following commands. • Assign an IS-IS metric.
Changing the IS-Type To change the IS-type, use the following commands. You can configure the system to act as a Level 1 router, a Level 1-2 router, or a Level 2 router. To change the IS-type for the router, use the following commands. • Configure IS-IS operating level for a router. ROUTER ISIS mode is-type {level-1 | level-1-2 | level-2-only} • Default is level-1-2. Change the IS-type for the IS-IS process.
• For a VLAN interface, enter the keyword vlan then a number from 1 to 4094. Distribute Routes Another method of controlling routing information is to filter the information through a prefix list. Prefix lists are applied to incoming or outgoing routes and routes must meet the conditions of the prefix lists or Dell EMC Networking OS does not install the route in the routing table. The prefix lists are globally applied on all interfaces running IS-IS.
• Apply a configured prefix list to all incoming IPv6 IS-IS routes. ROUTER ISIS-AF IPV6 mode distribute-list prefix-list-name in [interface] Enter the type of interface and the interface information: • • For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a Loopback interface, enter the keyword loopback then a number from 0 to 16383.
ROUTER ISIS mode redistribute ospf process-id [level-1| level-1-2 | level-2] [metric value] [match external {1 | 2} | match internal] [metric-type {external | internal}] [route-map map-name] Configure the following parameters: • process-id the range is from 1 to 65535. • level-1, level-1-2, or level-2: assign all redistributed routes to a level. The default is level-2. • metric value the range is from 0 to 16777215. The default is 0. • match external the range is from 1 or 2.
Configuring Authentication Passwords You can assign an authentication password for routers in Level 1 and for routers in Level 2. Because Level 1 and Level 2 routers do not communicate with each other, you can assign different passwords for Level 1 routers and for Level 2 routers. However, if you want the routers in the level to communicate with each other, configure them with the same password. To configure a simple text password, use the following commands.
eljefe.00-00 * 0x0000000A 0xF963 eljefe.01-00 * 0x00000001 0x68DF eljefe.02-00 * 0x00000001 0x2E7F Force10.00-00 0x00000002 0xD1A7 IS-IS Level-2 Link State Database LSPID LSP Seq Num LSP Checksum B233.00-00 0x00000006 0xC38A eljefe.00-00 * 0x0000000E 0x53BF eljefe.01-00 * 0x00000001 0x68DF eljefe.02-00 * 0x00000001 0x2E7F Force10.
To disable a specific debug command, enter the keyword no then the debug command. For example, to disable debugging of IS-IS updates, use the no debug isis updates-packets command. To disable all IS-IS debugging, use the no debug isis command. To disable all debugging, use the undebug all command. IS-IS Metric Styles The following sections provide additional information about the IS-IS metric styles.
Table 31. Metric Value When the Metric Style Changes Beginning Metric Style Final Metric Style Resulting IS-IS Metric Value wide narrow default value (10) if the original value is greater than 63. A message is sent to the console. wide transition truncated value (the truncated value appears in the LSP only). The original isis metric value is displayed in the show config and show running-config commands and is used if you change back to transition metric style.
Beginning Metric Style Final Metric Style Resulting IS-IS Metric Value commands and is used if you change back to transition metric style. Moving to transition and then to another metric style produces different results. Table 32.
Level-1 Metric Style Level-2 Metric Style Resulting Metric Value wide transition narrow truncated value wide transition narrow transition truncated value wide transition transition truncated value Sample Configurations The following configurations are examples for enabling IPv6 IS-IS. These examples are not comprehensive directions. They are intended to give you some guidance with typical configurations.
IS-IS Sample Configuration — Congruent Topology IS-IS Sample Configuration — Multi-topology IS-IS Sample Configuration — Multi-topology Transition The following is a sample configuration for enabling IPv6 IS-IS. DellEMC(conf-if-gi-3/17)#show config ! interface GigabitEthernet 3/17 ip address 24.3.1.1/24 ipv6 address 24:3::1/76 ip router isis ipv6 router isis no shutdown DellEMC(conf-if-gi-3/17)# DellEMC(conf-router_isis)#show config ! router isis metric-style wide level-1 metric-style wide level-2 net 34.
25 Link Aggregation Control Protocol (LACP) A link aggregation group (LAG), referred to as a port channel by the Dell EMC Networking OS, can provide both load-sharing and port redundancy across line cards. You can enable LAGs as static or dynamic. Introduction to Dynamic LAGs and LACP A link aggregation group (LAG), referred to as a port channel by Dell EMC Networking OS, can provide both load-sharing and port redundancy across line cards. You can enable LAGs as static or dynamic.
LACP Modes Dell EMC Networking OS provides three modes for configuration of LACP — Off, Active, and Passive. • Off — In this state, an interface is not capable of being part of a dynamic LAG. LACP does not run on any port that is configured to be in this state. • Active — In this state, the interface is said to be in the “active negotiating state.” LACP runs on any link that is configured to be in this state.
The default is 32768. LACP Configuration Tasks The following configuration tasks apply to LACP. • Creating a LAG • Configuring the LAG Interfaces as Dynamic • Setting the LACP Long Timeout • Monitoring and Debugging LACP • Configuring Shared LAG State Tracking Creating a LAG To create a dynamic port channel (LAG), use the following command. First you define the LAG and then the LAG interfaces. • Create a dynamic port channel (LAG).
DellEMC(conf)#interface Gigabitethernet 4/15 DellEMC(conf-if-gi-4/15)#no shutdown DellEMC(conf-if-gi-4/15)#port-channel-protocol lacp DellEMC(conf-if-gi-4/15-lacp)#port-channel 32 mode active ...
• Debug LACP, including configuration and events. EXEC mode [no] debug lacp [config | events | pdu [in | out | [interface [in | out]]]] Shared LAG State Tracking Shared LAG state tracking provides the flexibility to bring down a port channel (LAG) based on the operational state of another LAG. At any time, only two LAGs can be a part of a group such that the fate (status) of one LAG depends on the other LAG.
Example of LAGs in the Same Failover Group DellEMC#config DellEMC(conf)#port-channel failover-group DellEMC(conf-po-failover-grp)#group 1 port-channel 1 port-channel 2 To view the failover group configuration, use the show running-configuration po-failover-group command. DellEMC#show running-config po-failover-group ! port-channel failover-group group 1 port-channel 1 port-channel 2 As shown in the following illustration, LAGs 1 and 2 are members of a failover group.
Important Points about Shared LAG State Tracking The following is more information about shared LAG state tracking. • • • • • This feature is available for static and dynamic LAGs. Only a LAG can be a member of a failover group. You can configure shared LAG state tracking on one side of a link or on both sides. If a LAG that is part of a failover group is deleted, the failover group is deleted. If a LAG moves to the Down state due to this feature, its members may still be in the Up state.
Port is part of Port-channel 10 Hardware is DellEMCEth, address is 00:01:e8:06:95:c0 Current address is 00:01:e8:06:95:c0 Interface Index is 109101113 Port will not be disabled on partial SFM failure Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes LineSpeed 1000 Mbit, Mode full duplex, Slave Flowcontrol rx on tx on ARP type: ARPA, ARP Timeout 04:00:00 Last clearing of "show interface" counters 00:02:11 Queueing strategy: fifo Input statistics: 132 packets, 163668 bytes 0 Vlans 0 64-byte pkts,
Figure 53.
Figure 54.
Figure 55.
Summary of the LAG Configuration on Bravo Bravo(conf-if-gi-3/21)#int port-channel 10 Bravo(conf-if-po-10)#no ip add Bravo(conf-if-po-10)#switch Bravo(conf-if-po-10)#no shut Bravo(conf-if-po-10)#show config ! interface Port-channel 10 no ip address switchport no shutdown ! Bravo(conf-if-po-10)#exit Bravo(conf)#int gig 3/21 Bravo(conf)#no ip address Bravo(conf)#no switchport Bravo(conf)#shutdown Bravo(conf-if-gi-3/21)#port-channel-protocol lacp Bravo(conf-if-gi-3/21-lacp)#port-channel 10 mode active Bravo(con
Figure 56.
Figure 57.
Figure 58. Inspecting the LAG Status Using the show lacp command The point-to-point protocol (PPP) is a connection-oriented protocol that enables layer two links over various different physical layer connections. It is supported on both synchronous and asynchronous lines, and can operate in Half-Duplex or Full-Duplex mode. It was designed to carry IP traffic but is general enough to allow any type of network layer datagram to be sent over a PPP connection.
26 Layer 2 This chapter describes the Layer 2 features supported on the device. Manage the MAC Address Table You can perform the following management tasks in the MAC address table. • Clearing the MAC Address Table • Setting the Aging Time for Dynamic Entries • Configuring a Static MAC Address • Displaying the MAC Address Table Clearing the MAC Address Table You may clear the MAC address table of dynamic entries. To clear a MAC address table, use the following command.
Configuring a Static MAC Address A static entry is one that is not subject to aging. Enter static entries manually. To create a static MAC address entry, use the following command. • Create a static MAC address entry in the MAC address table. CONFIGURATION mode mac-address-table static Displaying the MAC Address Table To display the MAC address table, use the following command. • Display the contents of the MAC address table.
In this case, the configuration is still present in the running-config and show output. Remove the configuration before re-applying a MAC learning limit with a lower value. Also, ensure that you can view the Syslog messages on your session. NOTE: The CAM-check failure message beginning in Dell EMC Networking OS version 8.3.1.0 is different from versions 8.2.1.
converted to sticky MACs on that interface. To remove all sticky MAC addresses from the running config file, disable sticky MAC and use the write config command. When you enable sticky mac on an interface, dynamically-learned MAC addresses do not age, even if you enabled mac-learninglimit dynamic. If you configured mac-learning-limit and mac-learning-limit dynamic and you disabled sticky MAC, any dynamically-learned MAC addresses ages.
learn-limit-violation shutdown Setting Station Move Violation Actions no-station-move is the default behavior. You can configure the system to take an action if a station move occurs using one the following options with the mac learning-limit command. To display a list of interfaces configured with MAC learning limit or station move violation actions, use the following commands. • Generate a system log message indicating a station move.
Disabling MAC Address Learning on the System You can configure the system to not learn MAC addresses from LACP and LLDP BPDUs. To disable source MAC address learning from LACP and LLDP BPDUs, follow this procedure: • Disable source MAC address learning from LACP BPDUs. CONFIGURATION mode • mac-address-table disable-learning lacp Disable source MAC address learning from LLDP BPDUs. CONFIGURATION mode • mac-address-table disable-learning lldp Disable source MAC address learning from LACP and LLDP BPDUs.
NOTE: If you have configured the no mac-address-table station-move refresh-arp command, traffic continues to be forwarded to the failed NIC until the ARP entry on the switch times out. Figure 60.
Figure 61. Configuring Redundant Layer 2 Pairs without Spanning Tree You configure a redundant pair by assigning a backup interface to a primary interface with the switchport backup interface command. Initially, the primary interface is active and transmits traffic and the backup interface remains down. If the primary fails for any reason, the backup transitions to an active Up state. If the primary interface fails and later comes back up, it remains as the backup interface for the redundant pair.
Important Points about Configuring Redundant Pairs • • • • You may not configure any interface to be a backup for more than one interface, no interface can have more than one backup, and a backup interface may not have a backup interface. The active or backup interface may not be a member of a LAG. The active and standby do not have to be of the same type (1G, 10G, and so on). You may not enable any Layer 2 protocol on any interface of a redundant pair or to ports connected to them.
Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 2 Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-STATE_ACT_STBY: Changed interface state to standby: Po 2 DellEMC(conf-if-po-1)# DellEMC# DellEMC#show interfaces switchport backup Interface Status Paired Interface Status Port-channel 1 Active Port-chato mannel 2 Standby Port-channel 2 Standby Port-channel 1 Active DellEMC# DellEMC(conf-if-po-1)#switchport backup interface gigabitethernet 1/2 Apr 9 00:16:29: %STKUNIT0-M:CP %IFMGR
FEFD State Changes FEFD has two operational modes, Normal and Aggressive. When you enable Normal mode on an interface and a far-end failure is detected, no intervention is required to reset the interface to bring it back to an FEFD operational state. When you enable Aggressive mode on an interface in the same state, manual intervention is required to reset the interface.
Configuring FEFD You can configure FEFD for all interfaces from CONFIGURATION mode, or on individual interfaces from INTERFACE mode. To enable FEFD globally on all interfaces, use the following command. • Enable FEFD globally on all interfaces. CONFIGURATION mode fefd-global To report interval frequency and mode adjustments, use the following commands. 1 Setup two or more connected interfaces for Layer 2 or Layer 3.
fefd [mode {aggressive | normal}] • Disable FEFD protocol on one interface. INTERFACE mode fefd disable Disabling an interface shuts down all protocols working on that interface’s connected line. It does not delete your previous FEFD configuration which you can enable again at any time. To set up and activate two or more connected interfaces, use the following commands. 1 Setup two or more connected interfaces for Layer 2 or Layer 3.
2w1d22h: %RPM0-P:CP %IFMGR-5-INACTIVE: Changed Vlan interface state to inactive: Vl 1 2w1d22h : FEFD state on Gi 4/1 changed from Bi-directional to Unknown DellEMC#debug fefd packets DellEMC#2w1d22h : FEFD packet sent via interface Gi 1/1 Sender state -- Bi-directional Sender info -- Mgmt Mac(00:01:e8:14:89:25), Slot-Port(Gi 1/1) Peer info -- Mgmt Mac (00:01:e8:14:89:25), Slot-Port(Gi 4/1) Sender hold time -- 3 (second) 2w1d22h : FEFD packet received on interface Gi 4/1 Sender state -- Bi-directional Sender
27 Link Layer Discovery Protocol (LLDP) This chapter describes how to configure and use the link layer discovery protocol (LLDP). 802.1AB (LLDP) Overview LLDP — defined by IEEE 802.1AB — is a protocol that enables a local area network (LAN) device to advertise its configuration and receive configuration information from adjacent LLDP-enabled LAN infrastructure devices.
Table 35. Type, Length, Value (TLV) Types Type TLV Description 0 End of LLDPDU Marks the end of a LLDPDU. 1 Chassis ID An administratively assigned name that identifies the LLDP agent. 2 Port ID An administratively assigned name that identifies a port through which TLVs are sent and received. 3 Time to Live An administratively assigned name that identifies a port through which TLVs are sent and received.
Figure 65. Organizationally Specific TLV IEEE Organizationally Specific TLVs Eight TLV types have been defined by the IEEE 802.1 and 802.3 working groups as a basic part of LLDP; the IEEE OUI is 00-80-C2. You can configure the Dell EMC Networking system to advertise any or all of these TLVs. Table 36. Optional TLV Types Type TLV Description 4 Port description A user-defined alphanumeric string that describes the port. Dell EMC Networking OS does not currently support this TLV.
Type TLV Description in the Dell EMC Networking OS implementation of LLDP, but is available and mandatory (non-configurable) in the LLDPMED implementation. 127 Power via MDI Dell EMC Networking supports the LLDPMED protocol, which recommends that Power via MDI TLV be not implemented, and therefore Dell EMC Networking implements Extended Power via MDI TLV only.
Table 37. TIA-1057 (LLDP-MED) Organizationally Specific TLVs Type SubType TLV Description 127 1 LLDP-MED Capabilities Indicates: • • • whether the transmitting device supports LLDP-MED what LLDP-MED TLVs it supports LLDP device class 127 2 Network Policy Indicates the application type, VLAN ID, Layer 2 Priority, and DSCP value.
LLDP-MED Capabilities TLV The LLDP-MED capabilities TLV communicates the types of TLVs that the endpoint device and the network connectivity device support. LLDP-MED network connectivity devices must transmit the Network Policies TLV. • • The value of the LLDP-MED capabilities field in the TLV is a 2–octet bitmap, each bit represents an LLDP-MED capability (as shown in the following table). The possible values of the LLDP-MED device type are shown in the following.
• VLAN ID • VLAN tagged or untagged status • Layer 2 priority • DSCP value An integer represents the application type (the Type integer shown in the following table), which indicates a device function for which a unique network policy is defined. An individual LLDP-MED network policy TLV is generated for each application type that you specify with the Dell EMC Networking OS CLI (Advertising TLVs).
Extended Power via MDI TLV The extended power via MDI TLV enables advanced PoE management between LLDP-MED endpoints and network connectivity devices. Advertise the extended power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. • Power Type — there are two possible power types: power source entity (PSE) or power device (PD). The Dell EMC Networking system is a PSE, which corresponds to a value of 0, based on the TIA-1057 specification.
• LLDP is not hitless. LLDP Compatibility • Spanning tree and force10 ring protocol “blocked” ports allow LLDPDUs. • 802.1X controlled ports do not allow LLDPDUs until the connected device is authenticated. CONFIGURATION versus INTERFACE Configurations All LLDP configuration commands are available in PROTOCOL LLDP mode, which is a sub-mode of the CONFIGURATION mode and INTERFACE mode. • Configurations made at the CONFIGURATION level are global; that is, they affect all interfaces on the system.
Disabling and Undoing LLDP To disable or undo LLDP, use the following command. • Disable LLDP globally or for an interface. disable To undo an LLDP configuration, precede the relevant command with the keyword no. Enabling LLDP on Management Ports LLDP on management ports is enabled by default. To enable LLDP on management ports, use the following command. 1 Enter Protocol LLDP mode. CONFIGURATION mode protocol lldp 2 Enter LLDP management-interface mode.
To advertise TLVs, use the following commands. 1 Enter LLDP mode. CONFIGURATION or INTERFACE mode protocol lldp 2 Advertise one or more TLVs. PROTOCOL LLDP mode advertise { dot3-tlv | interface-port-desc | management-tlv | med } Include the keyword for each TLV you want to advertise. • For management TLVs: system-capabilities, system-description. • For 802.1 TLVs: port-protocol-vlan-id, port-vlan-id vlan-name. • For 802.3 TLVs: max-frame-size.
Storing and Viewing Unrecognized LLDP TLVs Dell EMC Networking OS provides support to store unrecognized (reserved and organizational specific) LLDP TLVs. Also, support is extended to retrieve the stored unrecognized TLVs using SNMP. When the incoming TLV from LLDP neighbors is not recognized, the TLV is categorized as unrecognized TLV.
View all the LLDP TLV information including unrecognized TLVs, using the snmpwalk and snmpget commands. For more details, see MIB Support to Display Unrecognized LLDP TLVs. Viewing the LLDP Configuration To view the LLDP configuration, use the following command. • Display the LLDP configuration. CONFIGURATION or INTERFACE mode show config Examples of Viewing LLDP Configurations The following example shows viewing an LLDP global configuration.
Gi 1/1 GigabitEthernet 1/5 Gi 1/2 GigabitEthernet 1/6 DellEMC(conf-if-gi-1/3)# 00:01:e8:05:40:46 00:01:e8:05:40:46 Example of Viewing Detailed Information Advertised by Neighbors DellEMC(conf)#do show lldp neighbors detail ======================================================================== Local Interface GigabitEthernet 1/1 has 2 neighbors Total Frames Out: 3 Total Frames In: 8 Total Neighbor information Age outs: 0 Total Multiple Neighbors Detected: 0 Total Frames Discarded: 0 Total In Error Frames
Remote Chassis ID Subtype: Mac address (4) Remote Chassis ID: 4c:76:25:f4:ab:01 Remote Port Subtype: Interface name (5) Remote Port ID: fortyGigE 1/2/8/1 Local Port ID: GigabitEthernet 1/2 Locally assigned remote Neighbor Index: 1 Remote TTL: 300 Information valid for next 201 seconds Time since last information change of this neighbor: 00:01:39 UnknownTLVList: OrgUnknownTLVList: ((00-01-66),127, 4) ((00-01-66),126, 4) ((00-01-66),125, 4) ((00-01-66),124, ((00-01-66),122, 4) ((00-01-66),121, 4) ((00-01-66),
no disable R1(conf-lldp)#no mode R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description no disable R1(conf-lldp)# Configuring Transmit and Receive Mode After you enable LLDP, the system transmits and receives LLDPDUs by default. To configure the system to transmit or receive only and return to the default, use the following commands. • Transmit only.
Configuring the Time to Live Value The information received from a neighbor expires after a specific amount of time (measured in seconds) called a time to live (TTL). The TTL is the product of the LLDPDU transmit interval (hello) and an integer called a multiplier. The default multiplier is 4, which results in a default TTL of 120 seconds. • Adjust the TTL value. CONFIGURATION mode or INTERFACE mode. multiplier • Return to the default multiplier value. CONFIGURATION mode or INTERFACE mode.
Figure 70. The debug lldp detail Command — LLDPDU Packet Dissection Example of debug lldp Command Output with Unrecognized Reserved and Organizational Specific LLDP TLVs The following is an example of LLDPDU with both (Reserved and Organizational specific) unrecognized TLVs.
• received and transmitted LLDP-MED TLVs Table 41. LLDP Configuration MIB Objects MIB Object Category LLDP Variable LLDP MIB Object Description LLDP Configuration adminStatus lldpPortConfigAdminStatus Whether you enable the local LLDP agent for transmit, receive, or both. msgTxHold lldpMessageTxHoldMultiplier Multiplier value. msgTxInterval lldpMessageTxInterval Transmit Interval value. rxInfoTTL lldpRxInfoTTL Time to live for received TLVs.
TLV Type 4 5 6 7 8 TLV Name Port Description System Name System Description System Capabilities Management Address TLV Variable System LLDP MIB Object port ID Local lldpLocPortId Remote lldpRemPortId Local lldpLocPortDesc Remote lldpRemPortDesc Local lldpLocSysName Remote lldpRemSysName Local lldpLocSysDesc Remote lldpRemSysDesc Local lldpLocSysCapSupported Remote lldpRemSysCapSupported Local lldpLocSysCapEnabled Remote lldpRemSysCapEnabled Local lldpLocManAddrLen R
TLV Type TLV Name TLV Variable PPVID 127 VLAN Name VID VLAN name length VLAN name System LLDP MIB Object Remote lldpXdot1RemProtoVlanEna bled Local lldpXdot1LocProtoVlanId Remote lldpXdot1RemProtoVlanId Local lldpXdot1LocVlanId Remote lldpXdot1RemVlanId Local lldpXdot1LocVlanName Remote lldpXdot1RemVlanName Local lldpXdot1LocVlanName Remote lldpXdot1RemVlanName Table 44.
TLV Sub-Type TLV Name TLV Variable System LLDP-MED MIB Object L2 Priority Local lldpXMedLocMediaPolicyPri ority Remote lldpXMedRemMediaPolicyP riority Local lldpXMedLocMediaPolicyDs cp Remote lldpXMedRemMediaPolicyD scp Local lldpXMedLocLocationSubty pe Remote lldpXMedRemLocationSubt ype Local lldpXMedLocLocationInfo Remote lldpXMedRemLocationInfo Local lldpXMedLocXPoEDeviceTy pe Remote lldpXMedRemXPoEDeviceT ype Local lldpXMedLocXPoEPSEPow erSource DSCP Value 3 Location Identi
TLV Sub-Type TLV Name TLV Variable System LLDP-MED MIB Object lldpXMedRemXPoEPDPow erReq 486 Link Layer Discovery Protocol (LLDP)
28 Microsoft Network Load Balancing Network load balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems (OSs). NLB uses a distributed methodology or pattern to equally split and balance the network traffic load across a set of servers that are part of the cluster or group.
With Multicast NLB mode, the data forwards to all the servers based on the port specified using the following Layer 2 multicast command in CONFIGURATION MODE: mac-address-table static multicast vlan output-range , Limitations of the NLB Feature The following limitations apply to switches on which you configure NLB: • The NLB Unicast mode uses switch flooding to transmit all packets to all the servers that are part of the VLAN.
• Enter the ip vlan-flooding command to specify that all Layer 3 unicast routed data traffic going through a VLAN member port floods across all the member ports of that VLAN. CONFIGURATION mode ip vlan-flooding There might be some ARP table entries that are resolved through ARP packets, which had the Ethernet MAC SA different from the MAC information inside the ARP packet. This unicast data traffic flooding occurs only for those packets that use these ARP entries.
29 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) is supported on Dell EMC Networking OS. Protocol Overview MSDP is a Layer 3 protocol that connects IPv4 protocol-independent multicast-sparse mode (PIM-SM) domains. A domain in the context of MSDP is a contiguous set of routers operating PIM within a common boundary defined by an exterior gateway protocol, such as border gateway protocol (BGP).
RPs advertise each (S,G) in its domain in type, length, value (TLV) format. The total number of TLVs contained in the SA is indicated in the “Entry Count” field. SA messages are transmitted every 60 seconds, and immediately when a new source is detected. Figure 72.
With Anycast RP, all the RPs are configured to be MSDP peers of each other. When a source registers with one RP, an SA message is sent to the other RPs informing them that there is an active source for a particular multicast group. The result is that each RP is aware of the active sources in the area of the other RPs. If any of the RPs fail, IP routing converges and one of the RPs becomes the active RP in more than one area. New sources register with the backup RP.
Figure 73.
Figure 74.
Figure 75.
Figure 76. Configuring MSDP Enable MSDP Enable MSDP by peering RPs in different administrative domains. 1 Enable MSDP. CONFIGURATION mode ip multicast-msdp 2 Peer PIM systems in different administrative domains. CONFIGURATION mode ip msdp peer connect-source Examples of Configuring and Viewing MSDP R3(conf)#ip multicast-msdp R3(conf)#ip msdp peer 192.168.0.
R3(conf)#do show ip msdp summary Peer Addr Description Local Addr State Source SA Up/Down To view details about a peer, use the show ip msdp peer command in EXEC privilege mode. Multicast sources in remote domains are stored on the RP in the source-active cache (SA cache). The system does not create entries in the multicast routing table until there is a local receiver for the corresponding multicast group. R3#show ip msdp peer Peer Addr: 192.168.0.1 Local Addr: 192.168.0.
show ip msdp sa-limit If the total number of active sources is already larger than the limit when limiting is applied, the sources that are already in Dell EMC Networking OS are not discarded. To enforce the limit in such a situation, use the clear ip msdp sa-cache command to clear all existing entries. Clearing the Source-Active Cache To clear the source-active cache, use the following command. • Clear the SA cache of all, local, or rejected entries, or entries for a specific group.
Figure 77.
Figure 78.
Figure 79. MSDP Default Peer, Scenario 4 Specifying Source-Active Messages To specify messages, use the following command. • Specify the forwarding-peer and originating-RP from which all active sources are accepted without regard for the RPF check. CONFIGURATION mode ip msdp default-peer ip-address list If you do not specify an access list, the peer accepts all sources that peer advertises. All sources from RPs that the ACL denies are subject to the normal RPF check.
GroupAddr 229.0.50.2 229.0.50.3 229.0.50.4 SourceAddr 24.0.50.2 24.0.50.3 24.0.50.4 RPAddr 200.0.0.50 200.0.0.50 200.0.0.50 LearnedFrom 10.0.50.2 10.0.50.2 10.0.50.2 DellEMC#ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 3 rejected SAs received, cache-size 32766 UpTime GroupAddr SourceAddr RPAddr 00:33:18 229.0.50.64 24.0.50.64 200.0.1.50 00:33:18 229.0.50.65 24.0.50.65 200.0.1.50 00:33:18 229.0.50.66 24.0.50.66 200.0.1.50 Expire 73 73 73 UpTime 00:13:49 00:13:49 00:13:49 LearnedFrom 10.0.50.
R1_E600(conf)#do show ip msdp sa-cache R1_E600(conf)#do show ip msdp sa-cache rejected-sa MSDP Rejected SA Cache 1 rejected SAs received, cache-size 1000 UpTime GroupAddr SourceAddr RPAddr LearnedFrom 00:02:20 239.0.0.1 10.11.4.2 192.168.0.1 local Reason Redistribute Preventing MSDP from Caching a Remote Source To prevent MSDP from caching a remote source, use the following commands. 1 OPTIONAL: Cache sources that the SA filter denies in the rejected SA cache.
Example of Verifying the System is not Advertising Local Sources In the following example, R1 stops advertising source 10.11.4.2. Because it is already in the SA cache of R3, the entry remains there until it expires. [Router 1] R1(conf)#do show run msdp ! ip multicast-msdp ip msdp peer 192.168.0.3 connect-source Loopback 0 ip msdp sa-filter out 192.168.0.3 list mylocalfilter R1(conf)#do show run acl ! ip access-list extended mylocalfilter seq 5 deny ip host 239.0.0.1 host 10.11.4.
Output (S,G) filter: none [Router 1] R1(conf)#do show ip msdp peer Peer Addr: 192.168.0.3 Local Addr: 0.0.0.0(0) Connect Source: Lo 0 State: Inactive Up/Down Time: 00:00:03 Timers: KeepAlive 30 sec, Hold time 75 sec SourceActive packet count (in/out): 0/0 SAs learned from this peer: 0 SA Filtering: Clearing Peer Statistics To clear the peer statistics, use the following command. • Reset the TCP connection to the peer and clear all peer statistics.
03:17:10 : MSDP-0: Peer 192.168.0.3, 03:17:27 : MSDP-0: Peer 192.168.0.3, Input (S,G) filter: none Output (S,G) filter: none rcvd Keepalive msg sent Source Active msg MSDP with Anycast RP Anycast RP uses MSDP with PIM-SM to allow more than one active group to use RP mapping.
Figure 80. MSDP with Anycast RP Configuring Anycast RP To configure anycast RP, use the following commands. 1 In each routing domain that has multiple RPs serving a group, create a Loopback interface on each RP serving the group with the same IP address. CONFIGURATION mode interface loopback 2 Make this address the RP for the group.
4 Peer each RP with every other RP using MSDP, specifying the unique Loopback address as the connect-source. CONFIGURATION mode ip msdp peer 5 Advertise the network of each of the unique Loopback addresses throughout the network. ROUTER OSPF mode network Reducing Source-Active Message Flooding RPs flood source-active messages to all of their peers away from the RP.
interface Loopback 1 ip address 192.168.0.11/32 no shutdown ! router ospf 1 network 10.11.2.0/24 area 0 network 10.11.1.0/24 area 0 network 10.11.3.0/24 area 0 network 192.168.0.11/32 area 0 ! ip multicast-msdp ip msdp peer 192.168.0.3 connect-source Loopback 1 ip msdp peer 192.168.0.22 connect-source Loopback 1 ip msdp mesh-group AS100 192.168.0.22 ip msdp originator-id Loopback 1! ip pim rp-address 192.168.0.1 group-address 224.0.0.
The following example shows an R3 configuration for MSDP with Anycast RP. ip multicast-routing ! interface GigabitEthernet 3/21 ip pim sparse-mode ip address 10.11.0.32/24 no shutdown interface GigabitEthernet 3/41 ip pim sparse-mode ip address 10.11.6.34/24 no shutdown ! interface Loopback 0 ip pim sparse-mode ip address 192.168.0.3/32 no shutdown ! router ospf 1 network 10.11.6.0/24 area 0 network 192.168.0.
interface Loopback 0 ip pim sparse-mode ip address 192.168.0.1/32 no shutdown ! router ospf 1 network 10.11.2.0/24 area 0 network 10.11.1.0/24 area 0 network 192.168.0.1/32 area 0 network 10.11.3.0/24 area 0 ! ip multicast-msdp ip msdp peer 192.168.0.3 connect-source Loopback 0 ! ip pim rp-address 192.168.0.1 group-address 224.0.0.0/4 MSDP Sample Configuration: R2 Running-Config ip multicast-routing ! interface GigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.4.
ip address 10.11.6.34/24 no shutdown ! interface ManagementEthernet 1/1 ip address 10.11.80.3/24 no shutdown ! interface Loopback 0 ip pim sparse-mode ip address 192.168.0.3/32 no shutdown ! router ospf 1 network 10.11.6.0/24 area 0 network 192.168.0.3/32 area 0 redistribute static redistribute connected redistribute bgp 200 ! router bgp 200 redistribute ospf 1 neighbor 192.168.0.2 remote-as 100 neighbor 192.168.0.2 ebgp-multihop 255 neighbor 192.168.0.2 update-source Loopback 0 neighbor 192.168.0.
30 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP) — specified in IEEE 802.1Q-2003 — is a rapid spanning tree protocol (RSTP)-based spanning tree variation that improves per-VLAN spanning tree plus (PVST+). MSTP allows multiple spanning tree instances and allows you to map many VLANs to one spanning tree instance to reduce the total number of required instances. Protocol Overview MSTP — specified in IEEE 802.
• Enable Multiple Spanning Tree Globally • Adding and Removing Interfaces • Creating Multiple Spanning Tree Instances • Influencing MSTP Root Selection • Interoperate with Non-Dell Bridges • Changing the Region Name or Revision • Modifying Global Parameters • Modifying the Interface Parameters • Configuring an EdgePort • Flush MAC Addresses after a Topology Change • MSTP Sample Configurations • Debugging and Verifying MSTP Configurations Spanning Tree Variations The Dell EMC Networki
Related Configuration Tasks The following are the related configuration tasks for MSTP.
• spanning-tree 0 To remove an interface from the MSTP topology, use the no spanning-tree 0 command. Creating Multiple Spanning Tree Instances To create multiple spanning tree instances, use the following command. A single MSTI provides no more benefit than RSTP. To take full advantage of MSTP, create multiple MSTIs and map VLANs to them. • Create an MSTI. PROTOCOL MSTP mode msti Specify the keyword vlan then the VLANs that you want to participate in the MSTI.
Port path cost 20000, Port priority 128, Port Identifier 128.384 Designated root has priority 32768, address 0001.e806.953e Designated bridge has priority 32768, address 0001.e809.c24a Designated port id is 128.
Changing the Region Name or Revision To change the region name or revision, use the following commands. • Change the region name. PROTOCOL MSTP mode name name • Change the region revision number. PROTOCOL MSTP mode revision number Example of the name Command To view the current region name and revision, use the show spanning-tree mst configuration command from EXEC Privilege mode.
NOTE: With large configurations (especially those configurations with more ports) Dell EMC Networking recommends increasing the hello-time. The range is from 1 to 10. The default is 2 seconds. 3 Change the max-age parameter. PROTOCOL MSTP mode max-age seconds The range is from 6 to 40. The default is 20 seconds. 4 Change the max-hops parameter. PROTOCOL MSTP mode max-hops number The range is from 1 to 40. The default is 20.
Port Cost Default Value 25-Gigabit Ethernet interfaces 1700 40-Gigabit Ethernet interfaces 1400 50-Gigabit Ethernet interfaces 1200 100-Gigabit Ethernet interfaces 200 Port Channel with 100 Mb/s Ethernet interfaces 180000 Port Channel with 1-Gigabit Ethernet interfaces 18000 Port Channel with 10-Gigabit Ethernet interfaces 1800 Port Channel with 25-Gigabit Ethernet interfaces 1200 Port Channel with 50-Gigabit Ethernet interfaces 200 Port Channel with 100-Gigabit Ethernet interfaces 180
• If the interface to be shut down is a port channel, all the member ports are disabled in the hardware. • When you add a physical port to a port channel already in the Error Disable state, the new member port is also disabled in the hardware. • When you remove a physical port from a port channel in the Error Disable state, the error disabled state is cleared on this physical port (the physical port is enabled in the hardware).
Figure 82. MSTP with Three VLANs Mapped to Two Spanning Tree Instances Router 1 Running-Configuration This example uses the following steps: 1 Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2 Assign Layer-2 interfaces to the MSTP topology. 3 Create VLANs mapped to MSTP instances tag interfaces to the VLANs.
interface Vlan 300 no ip address tagged GigabitEthernet 1/21,31 no shutdown Router 2 Running-Configuration This example uses the following steps: 1 Enable MSTP globally and set the region name and revision map MSTP instances to the VLANs. 2 Assign Layer-2 interfaces to the MSTP topology. 3 Create VLANs mapped to MSTP instances tag interfaces to the VLANs.
MSTI 2 VLAN 200,300 ! (Step 2) interface GigabitEthernet 3/11 no ip address switchport no shutdown ! interface GigabitEthernet 3/21 no ip address switchport no shutdown ! (Step 3) interface Vlan 100 no ip address tagged GigabitEthernet 3/11,21 no shutdown ! interface Vlan 200 no ip address tagged GigabitEthernet 3/11,21 no shutdown ! interface Vlan 300 no ip address tagged GigabitEthernet 3/11,21 no shutdown SFTOS Example Running-Configuration This example uses the following steps: 1 Enable MSTP globally
interface vlan 200 tagged 1/0/31 tagged 1/0/32 exit interface vlan 300 tagged 1/0/31 tagged 1/0/32 exit Debugging and Verifying MSTP Configurations To debut and verify MSTP configuration, use the following commands. • Display BPDUs. EXEC Privilege mode • debug spanning-tree mstp bpdu Display MSTP-triggered topology change messages.
DellEMC# 4w0d4h : MSTP: Sending BPDU on Gi 2/21 : ProtId: 0, Ver: 3, Bpdu Type: MSTP, Flags 0x6e CIST Root Bridge Id: 32768:0001.e806.953e, Ext Path Cost: 0 Regional Bridge Id: 32768:0001.e806.953e, CIST Port Id: 128:470 Msg Age: 0, Max Age: 20, Hello: 2, Fwd Delay: 15, Ver1 Len: 0, Ver3 Len: 96 Name: Tahiti, Rev: 123, Int Root Path Cost: 0 Rem Hops: 20, Bridge Id: 32768:0001.e806.953e 4w0d4h : INST 1: Flags: 0x6e, Reg Root: 32768:0001.e806.
31 Multicast Features NOTE: Multicast routing is supported on secondary IP addresses; it is not supported on IPv6. NOTE: Multicast routing is supported across default and non-default virtual routing and forwarding (VRFs).
Protocol Ethernet Address VRRP 01:00:5e:00:00:12 PIM-SM 01:00:5e:00:00:0d • The Dell EMC Networking OS implementation of MTRACE is in accordance with IETF draft draft-fenner-traceroute-ipm. • Multicast is not supported on secondary IP addresses. • If you enable multicast routing, egress Layer 3 ACL is not applied to multicast data traffic. Multicast Policies The Dell EMC Networking OS supports multicast features for IPv4.
NOTE: The IN-L3-McastFib CAM partition stores multicast routes and is a separate hardware limit that exists per port-pipe. Any software-configured limit may supersede this hardware space limitation. The opposite is also true, the CAM partition might not be exhausted at the time the system-wide route limit is reached using the ip multicast-limit command.
Figure 83. Preventing a Host from Joining a Group The following table lists the location and description shown in the previous illustration. Table 47. Preventing a Host from Joining a Group — Description Location Description 1/21 • • • • Interface GigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 • • • Interface GigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
Location Description • no shutdown 2/1 • • • • Interface GigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.1.1/24 no shutdown 2/11 • • • • Interface GigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 • • • • Interface GigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 • • • • Interface GigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.
Preventing a PIM Router from Forming an Adjacency To prevent a router from participating in PIM (for example, to configure stub multicast routing), use the following command. • Prevent a router from participating in PIM. INTERFACE mode ip pim neighbor-filter Preventing a Source from Registering with the RP To prevent the PIM source DR from sending register packets to route processor (RP) for the specified multicast source and group, use the following command.
Figure 84. Preventing a Source from Transmitting to a Group The following table lists the location and description shown in the previous illustration. Table 48. Preventing a Source from Transmitting to a Group — Description Location Description 1/21 • • • • Interface GigabitEthernet 1/21 ip pim sparse-mode ip address 10.11.12.1/24 no shutdown 1/31 • • • Interface GigabitEthernet 1/31 ip pim sparse-mode ip address 10.11.13.
Location Description • no shutdown 2/1 • • • • Interface GigabitEthernet 2/1 ip pim sparse-mode ip address 10.11.1.1/24 no shutdown 2/11 • • • • Interface GigabitEthernet 2/11 ip pim sparse-mode ip address 10.11.12.2/24 no shutdown 2/31 • • • • Interface GigabitEthernet 2/31 ip pim sparse-mode ip address 10.11.23.1/24 no shutdown 3/1 • • • • Interface GigabitEthernet 3/1 ip pim sparse-mode ip address 10.11.5.
Preventing a PIM Router from Processing a Join To permit or deny PIM Join/Prune messages on an interface using an extended IP access list, use the following command. NOTE: Dell EMC Networking recommends not using the ip pim join-filter command on an interface between a source and the RP router. Using this command in this scenario could cause problems with the PIM-SM source registration process resulting in excessive traffic being sent to the CPU of both the RP and PIM DR of the source.
NOTE: You cannot configure the wait time. It is fixed to 3 seconds. Important Points to Remember • Destination address of the mtrace query message can be either a unicast or a multicast address. NOTE: When you use mtrace to trace a specific multicast group, the query is sent with the group's address as the destination. Retries of the query use the unicast address of the receiver.
• • • • OIF IP — outgoing interface address Proto — multicast routing protocol Forwarding code — error code as present in the response blocks Source Network/Mask — source mask Example of the mtrace Command to View the Network Path The following is an example of tracing a multicast route. R1>mtrace 103.103.103.3 1.1.1.1 226.0.0.3 Type Ctrl-C to abort. Querying reverse path for source 103.103.103.3 to destination 1.1.1.1 via group 226.0.0.
The response data block filled in by the last-hop router contains a Forwarding code field. Forwarding code can be added at any node and is not restricted to the last hop router. This field is used to record error codes before forwarding the response to the next neighbor in the path towards the source. In a response data packet, the following error codes are supported: Table 50.
Scenario Output 103.103.103.0/24 -4 103.103.103.3 --> Source ----------------------------------------------------------------- You can issue the mtrace command specifying the source multicast tree and multicast group without specifying the destination. Mtrace traces the complete path traversing through the multicast group to reach the source. The output displays the destination and the first hop (-1) as 0 to indicate any PIM enabled interface on the node. R1>mtrace 103.103.103.3 1.1.1.1 226.0.0.
Scenario Output -2 101.101.101.102 PIM 103.103.103.0/24 -3 2.2.2.1 PIM 103.103.103.0/24 -4 103.103.103.3 --> Source ----------------------------------------------------------------- You can issue the mtrace command by providing the source and multicast information. However, if the multicast group is a shared group (*,G), then mtrace traces the path of the shared tree until it reaches the RP. The source mask field reflects the shared tree that is being used to trace the path.
Scenario Output -2 20.20.20.2 PIM 6.6.6.0/24 -3 10.10.10.1 PIM No route default ----------------------------------------------------------------- If a multicast tree is not formed due to a configuration issue (for example, PIM is not enabled on one of the interfaces on the path), you can invoke a weak mtrace to identify the location in the network where the error has originated. R1>mtrace 6.6.6.6 4.4.4.5 Type Ctrl-C to abort.
Scenario Output -3 2.2.2.1 PIM 99.99.0.0/16 -4 * * * * ----------------------------------------------------------------If there is no response for mtrace even after switching to expanded hop search, the command displays an error message. R1>mtrace 99.99.99.99 1.1.1.1 Type Ctrl-C to abort. While traversing the path from source to destination, if the mtrace packet exhausts the maximum buffer size of the packet, then NO SPACE error is displayed in the output.
Scenario scenario, a corresponding error message is displayed. Output ---------------------------------------------------------------|Hop| OIF IP |Proto| Forwarding Code |Source Network/ Mask| ---------------------------------------------------------------0 4.4.4.5 --> Destination -1 4.4.4.4 PIM 6.6.6.0/24 -2 20.20.20.2 PIM 6.6.6.0/24 -3 10.10.10.1 PIM Wrong interface 6.6.6.0/24 ----------------------------------------------------------------R1>mtrace 6.6.6.6 4.4.4.5 Type Ctrl-C to abort.
32 Object Tracking IPv4 or IPv6 object tracking is available on Dell EMC Networking OS. Object tracking allows the Dell EMC Networking OS client processes, such as virtual router redundancy protocol (VRRP), to monitor tracked objects (for example, interface or link status) and take appropriate action when the state of an object changes. NOTE: In Dell EMC Networking OS release version 8.4.1.0, object tracking is supported only on VRRP.
Figure 85. Object Tracking Example When you configure a tracked object, such as an IPv4/IPv6 a route or interface, you specify an object number to identify the object. Optionally, you can also specify: • UP and DOWN thresholds used to report changes in a route metric. • A time delay before changes in a tracked object’s state are reported to a client. Track Layer 2 Interfaces You can create an object to track the line-protocol state of a Layer 2 interface.
Track IPv4 and IPv6 Routes You can create an object that tracks an IPv4 or IPv6 route entry in the routing table. Specify a tracked route by its IPv4 or IPv6 address and prefix-length. Optionally specify a tracked route by a virtual routing and forwarding (VRF) instance name if the route to be tracked is part of a VRF. The next-hop address is not part of the definition of the tracked object.
Set Tracking Delays You can configure an optional UP and/or DOWN timer for each tracked object to set the time delay before a change in the state of a tracked object is communicated to clients. The configured time delay starts when the state changes from UP to DOWN or the opposite way. If the state of an object changes back to its former UP/DOWN state before the timer expires, the timer is cancelled and the client is not notified.
To configure object tracking on the status of a Layer 2 interface, use the following commands. 1 Configure object tracking on the line-protocol state of a Layer 2 interface. CONFIGURATION mode track object-id interface interface line-protocol Valid object IDs are from 1 to 500. 2 (Optional) Configure the time delay used before communicating a change in the status of a tracked interface. OBJECT TRACKING mode delay {[up seconds] [down seconds]} Valid delay times are from 0 to 180 seconds. The default is 0.
For an IPv6 interface, a routing object only tracks the UP/DOWN status of the specified IPv6 interface (the track interface ipv6routing command). • The status of an IPv6 interface is UP only if the Layer 2 status of the interface is UP and the interface has a valid IPv6 address. • The Layer 3 status of an IPv6 interface goes DOWN when its Layer 2 status goes down (for a Layer 3 VLAN, all VLAN ports must be down) or the IPv6 address is removed from the routing table.
Interface GigabitEthernet 7/11 ipv6 routing Description: Austin access point Track an IPv4/IPv6 Route You can create an object that tracks the reachability or metric of an IPv4 or IPv6 route. You specify the route to be tracked by its address and prefix-length values. Optionally, for an IPv4 route, you can enter a VRF instance name if the route is part of a VPN routing and forwarding (VRF) table. The next-hop address is not part of the definition of a tracked IPv4/ IPv6 route.
Tracking Route Reachability Use the following commands to configure object tracking on the reachability of an IPv4 or IPv6 route. To remove object tracking, use the no track object-id command. 1 Configure object tracking on the reachability of an IPv4 or IPv6 route. CONFIGURATION mode track object-id {ip route ip-address/prefix-len | ipv6 route ipv6-address/prefix-len} reachability [vrf vrf-name] Valid object IDs are from 1 to 500.
The following example configures object tracking on the reachability of an IPv6 route: DellEMC(conf)#track 105 ipv6 route 1234::/64 reachability DellEMC(conf-track-105)#delay down 5 DellEMC(conf-track-105)#description Headquarters DellEMC(conf-track-105)#end DellEMC#show track 105 Track 105 IPv6 route 1234::/64 reachability Description: Headquarters Reachability is Down (route not in route table) 2 changes, last change 00:03:03 Tracking a Metric Threshold Use the following commands to configure object trac
threshold metric {[up number] [down number]} The default UP threshold is 254. The routing state is UP if the scaled route metric is less than or equal to the UP threshold. The defult DOWN threshold is 255. The routing state is DOWN if the scaled route metric is greater than or equal to the DOWN threshold. 6 (Optional) Display the tracking configuration.
First-hop interface is GigabitEthernet 1/2 Tracked by: VRRP GigabitEthernet 2/30 IPv6 VRID 1 Track 3 IPv6 route 2050::/64 reachability Reachability is Up (STATIC) 5 changes, last change 00:02:16 First-hop interface is GigabitEthernet 1/2 Tracked by: VRRP GigabitEthernet 2/30 IPv6 VRID 1 Track 4 Interface GigabitEthernet 1/4 ip routing IP routing is Up 3 changes, last change 00:03:30 Tracked by: Example of the show track brief Command Router# show track brief ResId State 1 Resource LastChange IP route reach
33 Open Shortest Path First (OSPFv2 and OSPFv3) Open shortest path first (OSPFv2 for IPv4) and OSPF version 3 (OSPF for IPv6) are supported on Dell EMC Networking OS. This chapter provides a general description of OSPFv2 (OSPF for IPv4) and OSPFv3 (OSPF for IPv6) as supported in the Dell EMC Networking Operating System (OS). NOTE: The fundamental mechanisms of OSPF (flooding, DR election, area support, SPF calculations, and so on) are the same between OSPFv2 and OSPFv3.
Areas allow you to further organize your routers within in the AS. One or more areas are required within the AS. Areas are valuable in that they allow sub-networks to "hide" within the AS, thus minimizing the size of the routing tables on all routers. An area within the AS may not see the details of another area’s topology. AS areas are known by their area number or the router’s IP address. Figure 86. Autonomous System Areas Area Types The backbone of the network is Area 0. It is also called Area 0.0.0.
• A not-so-stubby area (NSSA) can import AS external route information and send it to the backbone. It cannot receive external AS information from the backbone or other areas. • Totally stubby areas are referred to as no summary areas in the Dell EMC Networking OS. Networks and Neighbors As a link-state protocol, OSPF sends routing information to other OSPF routers concerning the state of the links between them. The state (up or down) of those links is important.
Figure 87. OSPF Routing Examples Backbone Router (BR) A backbone router (BR) is part of the OSPF Backbone, Area 0. This includes all ABRs. It can also include any routers that connect only to the backbone and another ABR, but are only part of Area 0, such as Router I in the previous example. Area Border Router (ABR) Within an AS, an area border router (ABR) connects one or more areas to the backbone.
An ABR can connect to many areas in an AS, and is considered a member of each area it connects to. Autonomous System Border Router (ASBR) The autonomous system border area router (ASBR) connects to more than one AS and exchanges information with the routers in other ASs. Generally, the ASBR connects to a non-interior gate protocol (IGP) such as BGP or uses static routes.
• Type 7: External LSA — Routers in an NSSA do not receive external LSAs from ABRs, but are allowed to send external routing information for redistribution. They use Type 7 LSAs to tell the ABRs about these external routes, which the ABR then translates to Type 5 external LSAs and floods as normal to the rest of the OSPF network. • Type 8: Link LSA (OSPFv3) — This LSA carries the IPv6 address information of the local links.
Figure 88. Priority and Cost Examples OSPF with Dell EMC Networking OS The Dell EMC Networking OS supports up to 16,000 OSPF routes for OSPFv2. Dell EMC Networking OS version 9.4(0.0) and later support only one OSPFv2 process per VRF. Dell EMC Networking OS version 9.7(0.0) and later support OSPFv3 in VRF. Also, on OSPFv3, Dell EMC Networking OS supports only one OSPFv3 process per VRF. OSPFv2 and OSPFv3 can co-exist but you must configure them individually.
Graceful Restart When a router goes down without a graceful restart, there is a possibility for loss of access to parts of the network due to ongoing network topology changes. Additionally, LSA flooding and reconvergence can cause substantial delays. It is, therefore, desirable that the network maintains a stable topology if it is possible for data flow to continue uninterrupted.
Fast Convergence (OSPFv2, IPv4 Only) Fast convergence allows you to define the speeds at which LSAs are originated and accepted, and reduce OSPFv2 end-to-end convergence time. Dell EMC Networking OS allows you to accept and originate LSAs as soon as they are available to speed up route information propagation. NOTE: The faster the convergence, the more frequent the route calculations and updates. This impacts CPU utilization and may impact adjacency stability in larger topologies.
Examples of Setting and Viewing a Dead Interval In the following example, the dead interval is set at 4x the hello interval (shown in bold). DellEMC(conf)#int gigabitethernet 2/2 DellEMC(conf-if-gi-2/2)#ip ospf hello-interval 20 DellEMC(conf-if-gi-2/2)#ip ospf dead-interval 80 DellEMC(conf-if-gi-2/2)# In the following example, the dead interval is set at 4x the hello interval (shown in bold).
• Troubleshooting OSPFv2 1 Configure a physical interface. Assign an IP address, physical or Loopback, to the interface to enable Layer 3 routing. 2 Enable OSPF globally. Assign network area and neighbors. 3 Add interfaces or configure other attributes. 4 Set the time interval between when the switch receives a topology change and starts a shortest path first (SPF) calculation.
The OSPF process ID is the identifying number assigned to the OSPF process. The router ID is the IP address associated with the OSPF process. After the OSPF process and the VRF are tied together, the OSPF process ID cannot be used again in the system.
• Enable OSPFv2 on an interface and assign a network address range to a specific OSPF area. CONFIG-ROUTER-OSPF-id mode network ip-address mask area area-id The IP Address Format is A.B.C.D/M. The area ID range is from 0 to 65535 or A.B.C.D/M. Enable OSPFv2 on Interfaces Enable and configure OSPFv2 on each interface (configure for Layer 3 protocol), and not shutdown. You can also assign OSPFv2 to a Loopback interface as a virtual interface.
Process ID 1, Router ID 11.1.2.1, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 sec, State BDR, Priority 1 Designated Router (ID) 13.1.1.1, Interface address 10.2.3.2 Backup Designated Router (ID) 11.1.2.1, Interface address 10.2.3.1 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 00:00:05 Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 13.1.1.1 (Designated Router) DellEMC> Loopback interfaces also help the OSPF process.
CONFIG-ROUTER-OSPF-id mode area area-id stub [no-summary] Use the keywords no-summary to prevent transmission into the area of summary ASBR LSAs. Area ID is the number or IP address assigned when creating the area. Example of the show ip ospf database database-summary Command To view which LSAs are transmitted, use the show ip ospf database process-id database-summary command in EXEC Privilege mode. DellEMC#show ip ospf 34 database database-summary OSPF Router with ID (10.1.2.
Transmit Delay is 1 sec, State DOWN, Priority 1 Designated Router (ID) 10.1.2.100, Interface address 0.0.0.0 Backup Designated Router (ID) 0.0.0.0, Interface address 0.0.0.0 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 Hello due in 13:39:46 Neighbor Count is 0, Adjacent neighbor count is 0 GigabitEthernet 2/1 is up, line protocol is down Internet Address 10.1.3.100/24, Area 2.2.2.2 Process ID 34, Router ID 10.1.2.
The following examples shows how to disable fast-convergence. DellEMC#(conf-router_ospf-1)#no fast-converge DellEMC#(conf-router_ospf-1)#ex DellEMC#(conf)#ex DellEMC##show ip ospf 1 Routing Process ospf 1 with ID 192.168.67.
• Change the priority of the interface, which is used to determine the Designated Router for the OSPF broadcast network. CONFIG-INTERFACE mode ip ospf priority number • • number: the range is from 0 to 255 (the default is 1). Change the retransmission interval between LSAs. CONFIG-INTERFACE mode ip ospf retransmit-interval seconds • • seconds: the range is from 1 to 65535 (the default is 5 seconds). The retransmit interval must be the same on all routers in the OSPF network.
• All neighboring routers must share password to exchange OSPF information. Set the authentication change wait time in seconds between 0 and 300 for the interface. CONFIG-INTERFACE mode ip ospf auth-change-wait-time seconds This setting is the amount of time OSPF has available to change its interface authentication type. When you configure the auth-change-wait-time, OSPF sends out only the old authentication scheme until the wait timer expires.
graceful-restart role [helper-only | restart-only] Dell EMC Networking OS supports the following options: • Helper-only: the OSPFv2 router supports graceful-restart only as a helper router. • Restart-only: the OSPFv2 router supports graceful-restart only during unplanned restarts. By default, OSPFv2 supports both restarting and helper roles. Selecting one or the other role restricts OSPFv2 to the single selected role.
Applying Prefix Lists To apply prefix lists to incoming or outgoing OSPF routes, use the following commands. • Apply a configured prefix list to incoming OSPF routes. CONFIG-ROUTEROSPF-id mode distribute-list prefix-list-name in [interface] • Assign a configured prefix list to outgoing OSPF routes. CONFIG-ROUTEROSPF-id distribute-list prefix-list-name out [connected | isis | rip | static] Redistributing Routes You can add routes from other routing instances or protocols to the OSPF process.
• Have you enabled OSPF globally? • Is the OSPF process active on the interface? • Are adjacencies established correctly? • Are the interfaces configured for Layer 3 correctly? • Is the router in the correct area type? • Have the routes been included in the OSPF database? • Have the OSPF routes been included in the routing table (not just the OSPF database)? Some useful troubleshooting commands are: • show interfaces • show protocols • debug IP OSPF events and/or packets • show neighbor
Example of Viewing OSPF Configuration DellEMC#show run ospf ! router ospf 4 router-id 4.4.4.4 network 4.4.4.0/28 area 1 ! ipv6 router ospf 999 default-information originate always router-id 10.10.10.10 DellEMC# Sample Configurations for OSPFv2 The following configurations are examples for enabling OSPFv2. These examples are not comprehensive directions. They are intended to give you some guidance with typical configurations. You can copy and paste from these examples to your CLI.
interface Loopback 10 ip address 192.168.100.100/24 no shutdown OSPF Area 0 — Te 3/1 and 3/2 router ospf 33333 network 192.168.100.0/24 area 0 network 10.0.13.0/24 area 0 network 10.0.23.0/24 area 0 ! interface Loopback 30 ip address 192.168.100.100/24 no shutdown ! interface GigabitEthernet 3/1 ip address 10.1.13.3/24 no shutdown ! interface GigabitEthernet 3/2 ip address 10.2.13.3/24 no shutdown OSPF Area 0 — Te 2/1 and 2/2 router ospf 22222 network 192.168.100.0/24 area 0 network 10.2.21.
3 No-summary – To act as totally stubby area — NSSA area can be converted intoa totally stubby area to reduce the number of Type-3 LSAs. Once it is configured, NSSA ABR will inject Type-3 LSAs into the NSSA area for default routes. The remaining Type-3 LSAs are not allowed inside this area. Configuration Task List for OSPFv3 (OSPF for IPv6) This section describes the configuration tasks for Open Shortest Path First version 3 (OSPF for IPv6) on the switch.
Applying cost for OSPFv3 Change in bandwidth directly affects the cost of OSPF routes. • Explicitly specify the cost of sending a packet on an interface. INTERFACE mode ipv6 ospf interface-cost • • interface-cost:The range is from 1 to 65535. Default cost is based on the bandwidth. Specify how the OSPF interface cost is calculated based on the reference bandwidth method. The cost of an interface is calculated as Reference Bandwidth/Interface speed.
• process-id: the process ID number assigned. • area-id: the area ID for this interface. Assigning OSPFv3 Process ID and Router ID Globally To assign, disable, or reset OSPFv3 globally, use the following commands. • Enable the OSPFv3 process globally and enter OSPFv3 mode. CONFIGURATION mode ipv6 router ospf {process ID} • The range is from 0 to 65535. Assign the router ID for this OSPFv3 process. CONF-IPV6-ROUTER-OSPF mode router-id {number} • number: the IPv4 address. The format is A.B.C.D.
no ipv6 router ospf process-id vrf {vrf-name} • Reset the OSPFv3 process. EXEC Privilege mode clear ipv6 ospf [vrf vrf-name] process Configuring Stub Areas To configure IPv6 stub areas, use the following command. • Configure the area as a stub area. CONF-IPV6-ROUTER-OSPF mode area area-id stub [no-summary] • no-summary: use these keywords to prevent transmission in to the area of summary ASBR LSAs. • Area ID: a number or IP address assigned when creating the area.
redistribute {bgp | connected | static} [metric metric-value | metric-type type-value] [routemap map-name] [tag tag-value] Configure the following required and optional parameters: • bgp | connected | static: enter one of the keywords to redistribute those routes. • metric metric-value: The range is from 0 to 4294967295. • metric-type metric-type: enter 1 for OSPFv3 external route type 1 OR 2 for OSPFv3 external route type 2. • route-map map-name: enter a name of a configured route map.
INTERFACE mode • ipv6 ospf graceful-restart helper-reject Specify the operating mode and type of events that trigger a graceful restart. CONF-IPV6-ROUTER-OSPF mode graceful-restart mode [planned-only | unplanned-only] • • Planned-only: the OSPFv3 router supports graceful restart only for planned restarts. A planned restart is when you manually enter a redundancy force-failover rpm command to force the primary RPM over to the secondary RPM.
OSPFv3 Router with ID (200.1.1.
To ensure integrity, data origin authentication, detection and rejection of replays, and confidentiality of the packet, RFC 4302 and RFC 4303 propose using two security protocols — authentication header (AH) and encapsulating security payload (ESP). For OSPFv3, these two IPsec protocols provide interoperable, high-quality cryptographically-based security.
• To configure an IPsec security policy for authenticating or encrypting OSPFv3 packets on a physical, port-channel, or VLAN interface or OSPFv3 area, perform any of the following tasks: • Configuring IPsec Authentication on an Interface • Configuring IPsec Encryption on an Interface • Configuring IPsec Authentication for an OSPFv3 Area • Configuring IPsec Encryption for an OSPFv3 Area • Displaying OSPFv3 IPsec Security Policies Configuring IPsec Authentication on an Interface To configure, remov
ipv6 ospf encryption {null | ipsec spi number esp encryption-algorithm [key-encryption-type] key authentication-algorithm [key-authentication-type] key} • • null: causes an encryption policy configured for the area to not be inherited on the interface. • ipsec spi number: is the security policy index (SPI) value. The range is from 256 to 4294967295. • esp encryption-algorithm: specifies the encryption algorithm used with ESP. The valid values are 3DES, DES, AES-CBC, and NULL.
• • • key: specifies the text string used in authentication. All neighboring OSPFv3 routers must share key to exchange information. For MD5 authentication, the key must be 32 hex digits (non-encrypted) or 64 hex digits (encrypted). For SHA-1 authentication, the key must be 40 hex digits (non-encrypted) or 80 hex digits (encrypted). Remove an IPSec authentication policy from an OSPFv3 area.
Displaying OSPFv3 IPsec Security Policies To display the configuration of IPsec authentication and encryption policies, use the following commands. • Display the AH and ESP parameters configured in IPsec security policies, including the SPI number, key, and algorithms used. EXEC Privilege mode show crypto ipsec policy [name name] • • name: displays configuration details about a specified policy.
Inbound ESP Cipher Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba10345a1039ba8f8a Outbound ESP Cipher Key : bbdd96e6eb4828e2e27bc3f9ff541e43faa759c9ef5706ba10345a1039ba8f8a Transform set : esp-128-aes esp-sha1-hmac The following example shows the show crypto ipsec sa ipv6 command.
• Is the router in the correct area type? • Did you include the routes in the OSPF database? • Did you include the OSPF routes in the routing table (not just the OSPF database)? Some useful troubleshooting commands are: • show ipv6 interfaces • show ipv6 protocols • debug ipv6 ospf events and/or packets • show ipv6 neighbors • show ipv6 routes Viewing Summary Information To get general route, configuration, links status, and debug information, use the following commands.
34 Policy-based Routing (PBR) Policy-based routing (PBR) allows a switch to make routing decisions based on policies applied to an interface. Overview When a router receives a packet, the router decides where to forward the packet based on the destination address in the packet, which is used to look up an entry in a routing table. However, in some cases, there may be a need to forward the packet based on other criteria: size, source, protocol type, destination, and so on.
• • Destination port TCP Flags After you apply a redirect-list to an interface, all traffic passing through it is subjected to the rules defined in the redirect-list. Traffic is forwarded based on the following: • • • • Next-hop addresses are verified. If the specified next hop is reachable, traffic is forwarded to the specified next-hop. If the specified next-hops are not reachable, the normal routing table is used to forward the traffic.
The Dell EMC Networking OS assigns the first available sequence number to a rule configured without a sequence number and inserts the rule into the PBR CAM region next to the existing entries. Because the order of rules is important, ensure that you configure any necessary sequence numbers. Never apply the permit statement because the redirect list covers all source and destination IP addresses. ip redirect-list rcl0 seq 5 redirect 2.2.2.2 ip any any seq 10 permit ip host 3.3.3.
• FORMAT: slot/port • ip-protocol-number or protocol-type is the type of protocol to be redirected • FORMAT: 0-255 for IP protocol number, or enter protocol type • source ip-address or any or host ip-address is the Source’s IP address • FORMAT: A.B.C.D/NN, or ANY or HOST IP address • destination ip-address or any or host ip-address is the Destination’s IP address • FORMAT: A.B.C.D/NN, or ANY or HOST IP address To delete a rule, use the no redirect command.
! ip redirect-list test seq 10 redirect 10.1.1.2 ip 20.1.1.0/24 any seq 15 redirect 10.1.1.3 ip 20.1.1.0/25 any seq 20 redirect 10.1.1.3 ip 20.1.1.0/24 any DellEMC(conf-redirect-list)# NOTE: Starting with the Dell EMC Networking OS version 9.4(0.0), the use of multiple recursive routes with the same source-address and destination-address combination in a redirect policy on an router.
In addition to supporting multiple redirect-lists in a redirect-group, multiple redirect-groups are supported on a single interface. Dell EMC Networking OS has the capability to support multiple groups on an interface for backup purposes. Show Redirect List Configuration To view the configuration redirect list configuration, use the following commands. 1 View the redirect list configuration and the associated interfaces.
NOTE: If you apply the redirect-list to an interface, the output of the show ip redirect-list redirect-listname command displays reachability status for the specified next-hop.
Create the Redirect-List GOLD Assign Redirect-List GOLD to Interface 2/11 View Redirect-List GOLD Creating a PBR list using Explicit Track Objects for Redirect IPs Create Track Objects to track the Redirect IPs: DellEMC#configure terminal DellEMC(conf)#track 3 ip host 42.1.1.2 reachability DellEMC(conf-track-3)#probe icmp DellEMC(conf-track-3)#track 4 ip host 43.1.1.
reachable (via Vl 20) seq 25 redirect 43.1.1.2 track 4 ip host 7.7.7.7 host 144.144.144.144, Track 4 [up], Next-hop reachable (via Vl 20) Applied interfaces: Te 2/28 DellEMC# Creating a PBR list using Explicit Track Objects for Tunnel Interfaces Creating steps for Tunnel Interfaces: DellEMC#configure terminal DellEMC(conf)#interface tunnel 1 DellEMC(conf-if-tu-1)#tunnel destination 40.1.1.2 DellEMC(conf-if-tu-1)#tunnel source 40.1.1.
DellEMC(conf-if-te-2/28)#exit DellEMC(conf)#end Verify the Applied Redirect Rules: DellEMC#show ip redirect-list explicit_tunnel IP redirect-list explicit_tunnel: Defined as: seq 5 redirect tunnel 1 track 1 tcp 155.55.2.0/24 222.22.2.0/24, Track 1 [up], Next-hop reachable (via Te 1/32) seq 10 redirect tunnel 1 track 1 tcp any any, Track 1 [up], Next-hop reachable (via Te 1/32) seq 15 redirect tunnel 1 track 1 udp 155.55.0.0/16 host 144.144.144.
35 PIM Sparse-Mode (PIM-SM) Protocol-independent multicast sparse-mode (PIM-SM) is a multicast protocol that forwards multicast traffic to a subnet only after a request using a PIM Join message; this behavior is the opposite of PIM-Dense mode, which forwards multicast traffic to all subnets until a request to stop. Implementation Information The following information is necessary for implementing PIM-SM.
Refuse Multicast Traffic A host requesting to leave a multicast group sends an IGMP Leave message to the last-hop DR. If the host is the only remaining receiver for that group on the subnet, the last-hop DR is responsible for sending a PIM Prune message up the RPT to prune its branch to the RP. 1 After receiving an IGMP Leave message, the gateway removes the interface on which it is received from the outgoing interface list of the (*,G) entry.
ip multicast-routing Related Configuration Tasks The following are related PIM-SM configuration tasks. • • • • Configuring S,G Expiry Timers Configuring a Static Rendezvous Point Configuring a Designated Router Creating Multicast Boundaries and Domains Enable PIM-SM You must enable PIM-SM on each participating interface. 1 Enable multicast routing on the system. CONFIGURATION mode ip multicast-routing 2 Enable PIM-Sparse mode.
The range is from 211 to 86,400 seconds. The default is 210. Example Configuring an (S,G) Expiry Time NOTE: The expiry time configuration is nullified and the default global expiry time is used if: • an ACL is specified in the ip pim sparse-mode sg-expiry-timer command, but the ACL has not been created or is a standard ACL. • if the expiry time is specified for an (S,G) entry in a deny rule. DellEMC(conf)#ip access-list extended SGtimer DellEMC(config-ext-nacl)#permit ip 10.1.2.3/24 225.1.1.
225.0.1.40 226.1.1.1 165.87.50.5 165.87.50.5 To display the assigned RP for a group range (group-to-RP mapping), use the show ip pim rp mapping command in EXEC privilege mode. DellEMC#show ip pim rp mapping PIM Group-to-RP Mappings Group(s): 224.0.0.0/4, Static RP: 165.87.50.5, v2 Configuring a Designated Router Multiple PIM-SM routers might be connected to a single local area network (LAN) segment. One of these routers is elected to act on behalf of directly connected hosts.
36 PIM Source-Specific Mode (PIM-SSM) PIM source-specific mode (PIM-SSM) is a multicast protocol that forwards multicast traffic from a single source to a subnet. In the other versions of protocol independent multicast (PIM), a receiver subscribes to a group only. The receiver receives traffic not just from the source in which it is interested but from all sources sending to that group.
Configure PIM-SSM Configuring PIM-SSM is a two-step process. 1 Configure PIM-SSM. 2 Enable PIM-SSM for a range of addresses. Related Configuration Tasks • Use PIM-SSM with IGMP Version 2 Hosts Enabling PIM-SSM To enable PIM-SSM, follow these steps. 1 Create an ACL that uses permit rules to specify what range of addresses should use SSM. CONFIGURATION mode ip access-list standard name 2 Enter the ip pim ssm-range command and specify the ACL you created.
To display the source to which a group is mapped, use the show ip igmp ssm-map [group] command. If you use the group option, the command displays the group-to-source mapping even if the group is not currently in the IGMP group table. If you do not specify the group option, the display is a list of groups currently in the IGMP group table that has a group-to-source mapping. To display the list of sources mapped to a group currently in the IGMP group table, use the show ip igmp groups group detail command.
Electing an RP using the BSR Mechanism Every PIM router within a domain must map a particular multicast group address to the same RP. The group-to-RP mapping may be statically or dynamically configured. RFC 5059 specifies a dynamic, self-configuring method called the Bootstrap Router (BSR) mechanism, by which an RP is elected from a pool of RP candidates (C-RPs). Some routers within the domain are configured to be C-RPs.
ip pim [vrf vrf-name] rp-Candidate interface [priority] [acl-name] The specified acl-list is associated to the rp-candidate. NOTE: You can create the ACL list of multicast prefix using the ip access-list standard command.
37 Power over Ethernet (PoE) The PoE feature supports electrical power and transmission of data on Ethernet cabling. A single cable can provide both data connection and electrical power to the attached devices such as wireless access points or IP cameras. Power over Ethernet (PoE), as described by IEEE 802.3af specifies that a maximum of 15.4 watts can be transmitted to Ethernet devices over the signal pairs of an unshielded twisted pair (UTP) cable.
Enable PoE/PoE+ PoE/PoE+ is disabled by default. You can enable PoE/PoE+ on a port by using the power inline command in the INTERFACE mode. • To manage the inline power in a stack unit, use the Class or Static mode. See Manage Inline Power. • To limit the maximum amount of power available to a powered device and to set the priority of power access by the ports, use the power inline {[max_milliwatts] | priority {critical | high | low}} command.
Dell# show os-version PoE-CONTROLLER IMAGE INFORMATION --------------------------------------------------------------------Type Version PoE Controller 2.63 3 Verify the power details on the stack unit.
Advertising Extended Power The power device(PD) sends the information in the LLDP-MED extended power via MDI TLV and information in the IEEE 802.3 power via MDI TLV. Dell Networking OS uses the following information sent through LLDP-MED extended power-via-MDI TLV. The power is advertised using the advertise med power-via-mdi command. • Power Requirement — Used for power allocation. • Power Priority — Used for priority calculation. The values are: Critical, High, Low.
This command has the following parameters. • stack unit unit-number — Enter the keywords stack unit and specify the stack unit number. The range is from 1 to 12. • threshold-value — Enter the power threshold limit value in percentage. Range is from 10 to 99. Default value is 99. Example of Setting the Global Threshold Limit The following example sets the global threshold limit for the PoE power budget to 10 percent on stack unit 1.
Power Allocation to Additional Ports When additional ports are enabled with PoE/PoE+, the power is allocated based on the budget. The power budget is the amount of power available from the installed PSUs minus the power required to operate the ports. Use the show power inline and show power detail commands to determine if power is available for additional PoE ports. For more information about these commands, see Dell Networking OS Command Line Reference Guide.
Restore Power Delivery on a Port You can temporarily disable and then restore power on a port. To disable the power delivery, see Suspend Power Delivery on a Port. To restore the suspended inline power, use the power inline restore stack-unit unit number command.
38 Port Monitoring Port monitoring (also referred to as mirroring ) allows you to monitor ingress and/or egress traffic on specified ports. The mirrored traffic can be sent to a port to which a network analyzer is connected to inspect or troubleshoot the traffic. Mirroring is used for monitoring Ingress or Egress or both Ingress and Egress traffic on a specific port(s). This mirrored traffic can be sent to a port where a network sniffer can connect and monitor the traffic.
• Source port (MD) can be a VLAN, where the VLAN traffic received on that port pipe where its members are present is monitored • Single MD can be monitored on max. of 4 MG ports. Port Monitoring Port monitoring is supported on both physical and logical interfaces, such as VLAN and port-channel interfaces. The source port (MD) with monitored traffic and the destination ports (MG) to which an analyzer can be attached must be on the same switch.
Example of Configuring Another Monitoring Session with a Previously Used Destination Port DellEMC(conf)#monitor session 300 DellEMC(conf-mon-sess-300)#$ destination gigabitethernet 1/4 direction tx DellEMC(conf-mon-sess-300)# DellEMC(conf-mon-sess-300)#do show monitor session SessID Source Destination Dir Mode Source IP Dest IP TTL Drop Rate Gre-Protocol FcMonitor ------ ------------------ ---- --------------------- -------------- -----0 Te 1/50 Te 1/51 rx Port N/A N/A A No N/A N/A yes 1 Gi 1/45 Gi 1/46 tx
6/2 direction tx, if the MD port Gig 6/1 is an untagged member of any VLAN, all monitored frames that the MG port Gig 6/2 receives are tagged with the VLAN ID of the MD port. Similarly, if BPDUs are transmitted, the MG port receives them tagged with the VLAN ID 4095. This behavior might result in a difference between the number of egress packets on the MD port and monitored packets on the MG port.
SessID Source Destination Gre-Protocol FcMonitor ------ -------------------------- --------0 Gi 1/1 Gi 1/2 A N/A No 0 Po 10 Gi 1/2 A N/A No 1 Vl 40 Gi 1/3 A N/A No Dir Mode Source IP Dest IP DSCP TTL Drop Rate --- ---- --------- -------- ---- --- ---- ---- rx Port 0.0.0.0 0.0.0.0 0 0 No N/ rx Port 0.0.0.0 0.0.0.0 0 0 No N/ rx Flow 0.0.0.0 0.0.0.0 0 0 No N/ NOTE: Source as VLAN is achieved via Flow based mirroring. Please refer section Enabling Flow-Based Monitoring.
EXEC Privilege mode show run monitor session DellEMC#show run monitor session ! monitor multicast-queue 7 DellEMC# Enabling Flow-Based Monitoring Flow-based monitoring conserves bandwidth by monitoring only specified traffic instead of all traffic on the interface. This feature is particularly useful when looking for malicious traffic. It is available for Layer 3 ingress traffic. You can specify traffic using standard or extended access-lists.
DellEMC(conf)#interface gigabitethernet 1/1 DellEMC(conf-if-gi-1/1)#ip access-group testflow in DellEMC(conf-if-gi-1/1)#show config ! interface GigabitEthernet 1/1 ip address 10.11.1.254/24 ip access-group testflow in shutdown DellEMC(conf-if-gi-1/1)#exit DellEMC(conf)#do show ip accounting access-list testflow ! Extended Ingress IP access list testflow on GigabitEthernet 1/1 Total cam count 4 seq 5 permit icmp any any 53 monitor 53 count bytes (0 packets 0 bytes) seq 10 permit ip 102.1.1.
Figure 92. Remote Port Mirroring Configuring Remote Port Mirroring Remote port mirroring requires a source session (monitored ports on different source switches), a reserved tagged VLAN for transporting mirrored traffic (configured on source, intermediate, and destination switches), and a destination session (destination ports connected to analyzers on destination switches).
• The L3 interface configuration should be blocked for RPM VLAN. • The member port of the reserved VLAN should have MTU and IPMTU value as MAX+4 (to hold the VLAN tag parameter). • To associate with source session, the reserved VLAN can have at max of only 4 member ports. • To associate with destination session, the reserved VLAN can have multiple member ports.
• On a source switch on which you configure source ports for remote port mirroring, you can add only one port to the dedicated RPM VLAN which is used to transport mirrored traffic. You can configure multiple ports for the dedicated RPM VLAN on intermediate and destination switches. Displaying Remote-Port Mirroring Configurations To display the current configuration of remote port mirroring for a specified session, enter the show config command in MONITOR SESSION configuration mode.
4 direction Specify rx, tx or both in case to monitor ingress/egress or both ingress and egress packets on the specified port.. 5 rpm source-ip dest-ip Specify the source ip address and the destination ip where the packet needs to be sent. 6 flow-based enable Specify flow-based enable for mirroring on a flow by flow basis and also for vlan as source. 7 no enable (Optional) No disable command is mandatory in order for a rpm session to be active.
DellEMC#show monitor session SessID Source Destination ------ ---------------1 Gi 1/5 remote-vlan 10 2 Vl 100 remote-vlan 20 3 Po 10 remote-vlan 30 DellEMC# Dir --rx rx both Mode ---Port Flow Port Source IP --------N/A N/A N/A Dest IP -------N/A N/A N/A Configuring the sample Source Remote Port Mirroring DellEMC(conf)#inte gi 1/1 DellEMC(conf-if-gi-1/1)#switchport DellEMC(conf-if-gi-1/1)#no shutdown DellEMC(conf-if-gi-1/1)#exit DellEMC(conf)#interface gi 1/2 DellEMC(conf-if-gi-1/2)#switchport DellEMC(c
1 Enable control plane egress acl using the following command: 2 Create an extended MAC access list and add a deny rule of (0x0180c2xxxxxx) packets using the following commands: mac control-plane egress-acl mac access-list extended mac2 seq 5 deny any 01:80:c2:00:00:00 00:00:00:ff:ff:ff count 3 Apply ACL on that RPM VLAN. In this example RPM vlan is 10.
To configure an ERPM session: Table 54. Configuration steps for ERPM Step Command Purpose 1 configure terminal Enter global configuration mode. 2 monitor session type erpm Specify a session ID and ERPM as the type of monitoring session, and enter the Monitoring-Session configuration mode. The session number needs to be unique and not already defined. 3 source { interface | range } direction {rx | tx | both} Specify the source port or range of ports.
no ip address tagged GigabitEthernet 1/1-3 mac access-group flow in <<<<<<<<<<<<<< Only ingress packets are supported for mirroring shutdown ERPM Behavior on a typical Dell EMC Networking OS The Dell EMC Networking OS is designed to support only the Encapsulation of the data received / transmitted at the specified source port (Port A). An ERPM destination session / decapsulation of the ERPM packets at the destination Switch are not supported. Figure 93.
b • The Header that gets attached to the packet is 38 bytes long. In case of a packet with L3 VLAN, it would be 42 bytes long. The original payload /original mirrored data starts from the 39th byte in a given ERPM packet. The first 38/42 bytes of the header needs to be ignored/ chopped off. • Some tools support options to edit the capture file. We can make use of such features (for example: editcap ) and chop the ERPM header part and save it to a new trace file. This new file (i.e.
VLTi link is added as an implicit member of the RPM vlan. As a result, the mirrored traffic also reaches the peer VLT device effecting VLTi link's bandwidth usage. To mitigate this issue, the L2 VLT egress mask drops the duplicate packets that egress out of the VLT port. If the LAG status of the peer VLT device is OPER-UP, then the other VLT peer blocks the transmission of packets received through VLTi to its port or LAG.
Scenario RPM Restriction Recommended Solution Mirroring Orphan Ports across VLT Devices — In this scenario, an orphan port on the primary VLT device is mirrored to another orphan port on the secondary VLT device through the ICL LAG. The port analyzer is connected to the secondary VLT device. No restrictions apply to the RPM session. The following example shows the configuration on the primary VLT device:source orphan port destination remote vlan direction rx/tx/both.
39 Private VLANs (PVLAN) The private VLAN (PVLAN) feature is supported on Dell EMC Networking OS. For syntax details about the commands described in this chapter, refer to the Private VLANs commands chapter in the Dell EMC Networking OS Command Line Reference Guide. Private VLANs extend the Dell EMC Networking OS security suite by providing Layer 2 isolation between ports within the same virtual local area network (VLAN).
• • A switch can have one or more primary VLANs, and it can have none. • A primary VLAN has one or more secondary VLANs. • A primary VLAN and each of its secondary VLANs decrement the available number of VLAN IDs in the switch. • A primary VLAN has one or more promiscuous ports. • A primary VLAN might have one or more trunk ports, or none. Secondary VLAN — a subdomain of the primary VLAN. • There are two types of secondary VLAN — community VLAN and isolated VLAN.
show vlan private-vlan [community | interface | isolated | primary | primary_vlan | interface interface] • Display primary-secondary VLAN mapping. EXEC mode or EXEC Privilege mode show vlan private-vlan mapping • Set the PVLAN mode of the selected port. INTERFACE switchport mode private-vlan {host | promiscuous | trunk} NOTE: Secondary VLANs are Layer 2 VLANs, so even if they are operationally down while primary VLANs are operationally up, Layer 3 traffic is still transmitted across secondary VLANs.
Example of the switchport mode private-vlan Command NOTE: You cannot add interfaces that are configured as PVLAN ports to regular VLANs. You also cannot add “regular” ports (ports not configured as PVLAN ports) to PVLANs. The following example shows the switchport mode private-vlan command on a port and on a port channel.
You can enter interfaces in numeric or in range format, either comma-delimited (slot/port,port,port) or hyphenated (slot/ port-port). You can only add promiscuous ports or PVLAN trunk ports to the PVLAN (no host or regular ports). 6 (OPTIONAL) Assign an IP address to the VLAN. INTERFACE VLAN mode ip address ip address 7 (OPTIONAL) Enable/disable Layer 3 communication between secondary VLANs.
interface vlan vlan-id 2 Enable the VLAN. INTERFACE VLAN mode no shutdown 3 Set the PVLAN mode of the selected VLAN to isolated. INTERFACE VLAN mode private-vlan mode isolated 4 Add one or more host ports to the VLAN. INTERFACE VLAN mode tagged interface or untagged interface You can enter the interfaces singly or in range format, either comma-delimited (slot/port,port,port) or hyphenated (slot/ port-port). You can only add ports defined as host to the VLAN.
Private VLAN Configuration Example The following example shows a private VLAN topology. Figure 94. Sample Private VLAN Topology The following configuration is based on the example diagram for the Z9500: • Te 1/1 and Te 1/23 are configured as promiscuous ports, assigned to the primary VLAN, VLAN 4000. • Te 1/25 is configured as a PVLAN trunk port, also assigned to the primary VLAN 4000. • Te 1/24 and Te 1/47 are configured as host ports and assigned to the isolated VLAN, VLAN 4003.
In parallel, on S4810: • Te 1/3 is a promiscuous port and Te 1/25 is a PVLAN trunk port, assigned to the primary VLAN 4000. • Te 1/4-6 are host ports. Te 1/4 and Te 1/5 are assigned to the community VLAN 4001, while Te 1/6 is assigned to the isolated VLAN 4003. The result is that: • The S4810 ports would have the same intra-switch communication characteristics as described for the Z9500.
The following example shows using the show vlan private-vlan mapping command. S50-1#show vlan private-vlan mapping Private Vlan: Primary : 4000 Isolated : 4003 Community : 4001 NOTE: In the following example, notice the addition of the PVLAN codes – P, I, and C – in the left column. The following example shows viewing the VLAN status.
40 Per-VLAN Spanning Tree Plus (PVST+) Per-VLAN spanning tree plus (PVST+) is a variation of spanning tree — developed by a third party — that allows you to configure a separate spanning tree instance for each virtual local area network (VLAN). Protocol Overview PVST+ is a variation of spanning tree — developed by a third party — that allows you to configure a separate spanning tree instance for each virtual local area network (VLAN).
Table 56. Spanning Tree Variations Dell EMC Networking OS Supports Dell EMC Networking Term IEEE Specification Spanning Tree Protocol (STP) 802 .1d Rapid Spanning Tree Protocol (RSTP) 802 .1w Multiple Spanning Tree Protocol (MSTP) 802 .1s Per-VLAN Spanning Tree Plus (PVST+) Third Party Implementation Information • The Dell EMC Networking OS implementation of PVST+ is based on IEEE Standard 802.1w. • The Dell EMC Networking OS implementation of PVST+ uses IEEE 802.
no disable Disabling PVST+ To disable PVST+ globally or on an interface, use the following commands. • Disable PVST+ globally. PROTOCOL PVST mode disable • Disable PVST+ on an interface, or remove a PVST+ parameter configuration. INTERFACE mode no spanning-tree pvst Example of Viewing PVST+ Configuration To display your PVST+ configuration, use the show config command from PROTOCOL PVST mode.
Figure 96. Load Balancing with PVST+ The bridge with the bridge value for bridge priority is elected root. Because all bridges use the default priority (until configured otherwise), the lowest MAC address is used as a tie-breaker. To increase the likelihood that a bridge is selected as the STP root, assign bridges a low non-default value for bridge priority. To assign a bridge priority, use the following command. • Assign a bridge priority.
Number of topology changes 5, last change occurred 00:34:37 ago on Gi 1/32 Port 375 (GigabitEthernet 1/22) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.375 Designated root has priority 4096, address 0001.e80d.b6:d6 Designated bridge has priority 4096, address 0001.e80d.b6:d6 Designated port id is 128.
Modifying Interface PVST+ Parameters You can adjust two interface parameters (port cost and port priority) to increase or decrease the probability that a port becomes a forwarding port. • Port cost — a value that is based on the interface type. The greater the port cost, the less likely the port is selected to be a forwarding port. • Port priority — influences the likelihood that a port is selected to be a forwarding port in case that several ports have the same port cost.
The values for interface PVST+ parameters are given in the output of the show spanning-tree pvst command, as previously shown. Configuring an EdgePort The EdgePort feature enables interfaces to begin forwarding traffic approximately 30 seconds sooner. In this mode an interface forwards frames by default until it receives a BPDU that indicates that it should behave otherwise; it does not go through the Learning and Listening states.
Figure 97. PVST+ with Extend System ID • Augment the bridge ID with the VLAN ID. PROTOCOL PVST mode extend system-id Example of Viewing the Extend System ID in a PVST+ Configuration DellEMC(conf-pvst)#do show spanning-tree pvst vlan 5 brief VLAN 5 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 32773, Address 0001.e832.73f7 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 32773 (priority 32768 sys-id-ext 5), Address 0001.e832.
no ip address tagged GigabitEthernet 1/22,32 no shutdown ! interface Vlan 300 no ip address tagged GigabitEthernet 1/22,32 no shutdown ! protocol spanning-tree pvst no disable vlan 100 bridge-priority 4096 Example of PVST+ Configuration (R2) interface GigabitEthernet 2/12 no ip address switchport no shutdown ! interface GigabitEthernet 2/32 no ip address switchport no shutdown ! interface Vlan 100 no ip address tagged GigabitEthernet 2/12,32 no shutdown ! interface Vlan 200 no ip address tagged GigabitEthe
protocol spanning-tree pvst no disable vlan 300 bridge-priority 4096 656 Per-VLAN Spanning Tree Plus (PVST+)
41 Quality of Service (QoS) This chapter describes how to use and configure Quality of Service service (QoS) features on the switch. Differentiated service is accomplished by classifying and queuing traffic, and assigning priorities to those queues. Table 58.
Feature Direction Create Policy Maps Ingress + Egress Create Input Policy Maps Ingress Honor DSCP Values on Ingress Packets Ingress Honoring dot1p Values on Ingress Packets Ingress Create Output Policy Maps Egress Specify an Aggregate QoS Policy Egress Create Output Policy Maps Egress Enabling QoS Rate Adjustment Enabling Strict-Priority Queueing Weighted Random Early Detection Egress Create WRED Profiles Egress Figure 98.
• Implementation Information • Port-Based QoS Configurations • Policy-Based QoS Configurations • DSCP Color Maps • Enabling QoS Rate Adjustment • Enabling Strict-Priority Queueing • Weighted Random Early Detection • Pre-Calculating Available QoS CAM Space • Configuring Weights and ECN for WRED • Configuring WRED and ECN Attributes • Guidelines for Configuring ECN for Classifying and Color-Marking Packets • Applying Layer 2 Match Criteria on a Layer 3 Interface • Applying DSCP and VL
Table 59. dot1p-priority Values and Queue Numbers dot1p Queue Number 0 0 1 0 2 0 3 1 4 2 5 3 6 3 7 3 • Change the priority of incoming traffic on the interface.
When priority-tagged frames ingress an untagged port or hybrid port, the frames are classified to the default VLAN of the port and to a queue according to their dot1p priority if you configure service-class dynamic dotp or trust dot1p. When priority-tagged frames ingress a tagged port, the frames are dropped because, for a tagged port, the default VLAN is 0. Dell EMC Networking OS Behavior: Hybrid ports can receive untagged, tagged, and priority tagged frames.
Example of rate shape Command DellEMC#configure terminal DellEMC(conf)#interface gigabitethernet 1/1 DellEMC(conf-if-gi-1/1)#rate shape 500 50 DellEMC(conf-if-gi-1/1)#end Policy-Based QoS Configurations Policy-based QoS configurations consist of the components shown in the following example. Figure 99. Constructing Policy-Based QoS Configurations Classify Traffic Class maps differentiate traffic so that you can apply separate quality of service policies to different types of traffic.
Creating a Layer 3 Class Map A Layer 3 class map differentiates ingress packets based on the DSCP value or IP precedence, and characteristics defined in an IP ACL. You can also use VLAN IDs and VRF IDs to classify the traffic using layer 3 class-maps. You may specify more than one DSCP and IP precedence value, but only one value must match to trigger a positive match for the class map. NOTE: IPv6 and IP-any class maps cannot match on ACLs or VLANs. Use step 1 or step 2 to start creating a Layer 3 class map.
The following example matches the IPv6 traffic with a DSCP value of 40: DellEMC(conf)# class-map match-all test DellEMC(conf-class-map)# match ipv6 dscp 40 The following example matches the IPv4 and IPv6 traffic with a precedence value of 3: DellEMC(conf)# class-map match-any test1 DellEMC(conf-class-map)#match ip-any precedence 3 Creating a Layer 2 Class Map All class maps are Layer 3 by default; however, you can create a Layer 2 class map by specifying the layer2 option with the class-map command.
The order can range from 0 to 254. By default, all ACL rules have an order of 255. Displaying Configured Class Maps and Match Criteria To display all class-maps or a specific class map, use the following command. Dell EMC Networking OS Behavior: An explicit “deny any" rule in a Layer 3 ACL used in a (match any or match all) class-map creates a "default to Queue 0" entry in the CAM, which causes unintended traffic classification. In the following example, traffic is classified in two Queues, 1 and 2.
• Layer 3 — QoS input policies allow you to rate police and set a DSCP or dot1p value. In addition, you can configure a drop precedence for incoming packets based on their DSCP value by using a DSCP color map. For more information, see DSCP Color Maps. • Layer 2 — QoS input policies allow you to rate police and set a dot1p value. Output QoS policies regulate egress traffic. The regulation mechanisms for output QoS policies are bandwidth percentage, scheduler strict, rate shaping and WRED.
Allocating Bandwidth to Queue Specifying WRED Drop Precedence Configuring Policy-Based Rate Shaping To configure policy-based rate shaping, use the following command. • Configure rate shape egress traffic. QOS-POLICY-OUT mode rate-shape Allocating Bandwidth to Queue The switch schedules packets for egress based on Deficit Round Robin (DRR). This strategy offers a guaranteed data rate. Allocate bandwidth to queues only in terms of percentage in 4-queue and 8-queue systems.
Create Policy Maps There are two types of policy maps: input and output. Creating Input Policy Maps There are two types of input policy-maps: Layer 3 and Layer 2. 1 Create a Layer 3 input policy map. CONFIGURATION mode policy-map-input Create a Layer 2 input policy map by specifying the keyword layer2 with the policy-map-input command.
Table 61.
dot1p Queue ID 6 3 7 3 The dot1p value is also honored for frames on the default VLAN. For more information, refer to Priority-Tagged Frames on the Default VLAN. • Enable the trust dot1p feature. POLICY-MAP-IN mode trust dot1p Mapping dot1p Values to Service Queues All traffic is by default mapped to the same queue, Queue 0. If you honor dot1p on ingress, you can create service classes based the queueing strategy in Honoring dot1p Values on Ingress Packets.
Creating Output Policy Maps 1 Create an output policy map. CONFIGURATION mode policy-map-output 2 After you create an output policy map, do one or more of the following: Applying an Output QoS Policy to a Queue Specifying an Aggregate QoS Policy Applying an Output Policy Map to an Interface 3 Apply the policy map to an interface. Applying an Output QoS Policy to a Queue To apply an output QoS policy to a queue, use the following command. • Apply an output QoS policy to queues.
Creating a DSCP Color Map You can create a DSCP color map to outline the differentiated services codepoint (DSCP) mappings to the appropriate color mapping (green, yellow, red) for the input traffic. The system uses this information to classify input traffic on an interface based on the DSCP value of each packet and assigns it an initial drop precedence of green, yellow, or red The default setting for each DSCP value (0-63) is green (low drop precedence).
Displaying DSCP Color Maps To display DSCP color maps, use the show qos dscp-color-map command in EXEC mode. Examples for Creating a DSCP Color Map Display all DSCP color maps. DellEMC# show qos dscp-color-map Dscp-color-map mapONE yellow 4,7 red 20,30 Dscp-color-map mapTWO yellow 16,55 Display a specific DSCP color map.
Enabling QoS Rate Adjustment By default while rate limiting, policing, and shaping, Dell EMC Networking OS does not include the Preamble, SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC are used for forwarding and are included in these rate metering calculations.
Traffic is a mixture of various kinds of packets. The rate at which some types of packets arrive might be greater than others. In this case, the space on the buffer and traffic manager (BTM) (ingress or egress) can be consumed by only one or a few types of traffic, leaving no space for other types. You can apply a WRED profile to a policy-map so that specified traffic can be prevented from consuming too much of the BTM resources. WRED uses a profile to specify minimum and maximum threshold values.
wred-profile 2 Specify the minimum and maximum threshold values. WRED mode threshold Applying a WRED Profile to Traffic After you create a WRED profile, you must specify to which traffic Dell EMC Networking OS should apply the profile. Dell EMC Networking OS assigns a color (also called drop precedence) — red, yellow, or green — to each packet based on it DSCP value before queuing it. DSCP is a 6–bit field.
Drop-statistic Dropped Pkts Green Yellow Out of Profile 51623 51300 0 DellEMC# Displaying egress–queue Statistics To display the number of transmitted and dropped packets and their rate on the egress queues of an interface, use the following command: • Display the number of packets and number of bytes on the egress-queue profile.
Specifically: • Available CAM — the available number of CAM entries in the specified CAM partition for the specified line card or stack-unit portpipe. • Estimated CAM — the estimated number of CAM entries that the policy will consume when it is applied to an interface. • Status — indicates whether the specified policy-map can be completely applied to an interface in the port-pipe.
You can enable WRED and ECN capabilities per queue for granularity. You can disable these functionality per queue, and you can also specify the minimum and maximum buffer thresholds for each color-coding of the packets. You can configure maximum drop rate percentage of yellow and green profiles. You can set up these parameters for both front-end and backplane ports. Global Service Pools With WRED and ECN Settings Support for global service pools is now available.
Configuring WRED and ECN Attributes The functionality to configure a weight factor for the WRED and ECN functionality for backplane ports is supported on the platform. WRED drops packets when the average queue length exceeds the configured threshold value to signify congestion. Explicit Congestion Notification (ECN) is a capability that enhances WRED by marking the packets instead of causing WRED to drop them when the threshold value is exceeded.
• Because this functionality forcibly marks all the packets matching the specific match criteria as ‘yellow’, Dell EMC Networking OS does not support Policer based coloring and this feature concurrently. • If single rate two color policer is configured along with this feature, then by default all packets less than PIR would be considered as “Green” But ‘Green’ packets matching the specific match criteria for which ‘color-marking’ is configured will be over-written and marked as “Yellow”.
3 Attach the policy-map to the interface. Dell EMC Networking OS support different types of match qualifiers to classify the incoming traffic. Match qualifiers can be directly configured in the class-map command or it can be specified through one or more ACL which in turn specifies the combination of match qualifiers. Until Release 9.3(0.0), support is available for classifying traffic based on the 6-bit DSCP field of the IPv4 packet.
By default, all packets are considered as ‘green’ (without the rate-policer and trust-diffserve configuration) and hence support would be provided to mark the packets as ‘yellow’ alone will be provided. By default Dell EMC Networking OS drops all the ‘RED’ or ‘violate’ packets.
seq 5 permit any dscp 50 ecn 1 seq 10 permit any dscp 50 ecn 2 seq 15 permit any dscp 50 ecn 3 ! ip access-list standard dscp_40_ecn seq 5 permit any dscp 40 ecn 1 seq 10 permit any dscp 40 ecn 2 seq 15 permit any dscp 40 ecn 3 ! ip access-list standard dscp_50_non_ecn seq 5 permit any dscp 50 ecn 0 ! ip access-list standard dscp_40_non_ecn seq 5 permit any dscp 40 ecn 0 ! class-map match-any class_dscp_40 match ip access-group dscp_40_non_ecn set-color yellow match ip access-group dscp_40_ecn ! class-map m
Applying DSCP and VLAN Match Criteria on a Service Queue You can configure Layer 3 class maps which contain both a Layer 3 Differentiated Services Code Point (DSCP) and IP VLAN IDs as match criteria to filter incoming packets on a service queue on the switch. To configure a Layer 3 class map to classify traffic according to both an IP VLAN ID and DSCP value, use the match ip vlan vlan-id command in class-map input configuration mode.
Classifying Incoming Packets Using ECN and ColorMarking Explicit Congestion Notification (ECN) is a capability that enhances WRED by marking the packets instead of causing WRED to drop them when the threshold value is exceeded. If you configure ECN for WRED, devices employ this functionality of ECN to mark the packets and reduce the rate of sending packets in a congested, heavily-loaded network.
Similar to ‘dscp’ qualifier in the existing L3 ACL command, the ‘ecn’ qualifier can be used along with all other supported ACL match qualifiers such as SIP/DIP/TCP/UDP/SRC PORT/DST PORT/ ICMP. Until Release 9.3(0.0), ACL supports classification based on the below TCP flags: • ACK • FIN • SYN • PSH • RST • URG You can now use the ‘ecn’ match qualifier along with the above TCP flag for classification.
• FIN • SYN • PSH • RST • URG In the existing software, ECE/CWR TCP flag qualifiers are not supported. • Because this functionality forcibly marks all the packets matching the specific match criteria as ‘yellow’, Dell EMC Networking OS does not support Policer based coloring and this feature concurrently.
seq 5 permit any dscp 40 ! ip access-list standard dscp_50_non_ecn seq 5 permit any dscp 50 ecn 0 ! ip access-list standard dscp_40_non_ecn seq 5 permit any dscp 40 ecn 0 ! class-map match-any class_dscp_40 match ip access-group dscp_40_non_ecn set-color yellow match ip access-group dscp_40 ! class-map match-any class_dscp_50 match ip access-group dscp_50_non_ecn set-color yellow match ip access-group dscp_50 ! policy-map-input pmap_dscp_40_50 service-queue 2 class-map class_dscp_40 service-queue 3 class-ma
42 Routing Information Protocol (RIP) The Routing Information Protocol (RIP) tracks distances or hop counts to nearby routers when establishing network connections and is based on a distance-vector algorithm. RIP is based on a distance-vector algorithm; it tracks distances or hop counts to nearby routers when establishing network connections. RIP protocol standards are listed in the Standards Compliance chapter.
Implementation Information Dell EMC Networking OS supports both versions of RIP and allows you to configure one version globally and the other version on interfaces or both versions on the interfaces. The following table lists the defaults for RIP in Dell EMC Networking OS. Table 66.
Enabling RIP Globally By default, RIP is not enabled in Dell EMC Networking OS. To enable RIP globally, use the following commands. 1 Enter ROUTER RIP mode and enable the RIP process on Dell EMC Networking OS. CONFIGURATION mode router rip 2 Assign an IP network address as a RIP network to exchange routing information.
192.161.1.0/24 auto-summary 192.162.3.0/24 [120/1] via 29.10.10.12, 00:01:22, Fa 1/49 192.162.3.0/24 auto-summary To disable RIP globally, use the no router rip command in CONFIGURATION mode. Configure RIP on Interfaces When you enable RIP globally on the system, interfaces meeting certain conditions start receiving RIP routes. By default, interfaces that you enable and configure with an IP address in the same subnet as the RIP network address receive RIPv1 and RIPv2 routes and send RIPv1 routes.
Adding RIP Routes from Other Instances In addition to filtering routes, you can add routes from other routing instances or protocols to the RIP process. With the redistribute command, you can include open shortest path first (OSPF), static, or directly connected routes in the RIP process. To add routes from other routing instances or protocols, use the following commands. • Include directly connected or user-configured (static) routes in RIP.
INTERFACE mode ip rip send version [1] [2] Examples of the RIP Process To see whether the version command is configured, use the show config command in ROUTER RIP mode. The following example shows the RIP configuration after the ROUTER RIP mode version command is set to RIPv2. When you set the ROUTER RIP mode version command, the interface () participating in the RIP process is also set to send and receive RIPv2 (shown in bold).
Generating a Default Route Traffic is forwarded to the default route when the traffic’s network is not explicitly listed in the routing table. Default routes are not enabled in RIP unless specified. Use the default-information originate command in ROUTER RIP mode to generate a default route into RIP. In Dell EMC Networking OS, default routes received in RIP updates from other routes are advertised if you configure the default-information originate command.
• • weight: the range is from 1 to 255. The default is 120. • ip-address mask: the IP address in dotted decimal format (A.B.C.D), and the mask in slash format (/x). • access-list-name: the name of a configured IP ACL. Apply an additional number to the incoming or outgoing route metrics.
Figure 101. RIP Topology Example RIP Configuration on Core2 The following example shows how to configure RIPv2 on a host named Core2. Example of Configuring RIPv2 on Core 2 Core2(conf-if-gi-2/3)# Core2(conf-if-gi-2/3)#router rip Core2(conf-router_rip)#ver 2 Core2(conf-router_rip)#network 10.200.10.0 Core2(conf-router_rip)#network 10.300.10.0 Core2(conf-router_rip)#network 10.11.10.0 Core2(conf-router_rip)#network 10.11.20.0 Core2(conf-router_rip)#show config ! router rip network 10.0.0.
The following example shows the show ip route command to show the RIP setup on Core 2.
Core3(conf-router_rip)#network 192.168.2.0 Core3(conf-router_rip)#network 10.11.30.0 Core3(conf-router_rip)#network 10.11.20.0 Core3(conf-router_rip)#show config ! router rip network 10.0.0.0 network 192.168.1.0 network 192.168.2.0 version 2 Core3(conf-router_rip)# Core 3 RIP Output The examples in this section show the core 2 RIP output. • To display Core 3 RIP database, use the show ip rip database command. • To display Core 3 RIP setup, use the show ip route command.
The following example shows the show ip protocols command to show the RIP configuration activity on Core 3.
! interface GigabitEthernet 3/2 ip address 10.11.20.1/24 no shutdown ! interface GigabitEthernet 3/4 ip address 192.168.1.1/24 no shutdown ! interface GigabitEthernet 3/5 ip address 192.168.2.1/24 no shutdown ! router rip version 2 network 10.11.20.0 network 10.11.30.0 network 192.168.1.0 network 192.168.2.
43 Remote Monitoring (RMON) RMON is an industry-standard implementation that monitors network traffic by sharing network monitoring information. RMON provides both 32-bit and 64-bit monitoring facility and long-term statistics collection on Dell EMC Networking Ethernet interfaces. RMON operates with the simple network management protocol (SNMP) and monitors all nodes on a local area network (LAN) segment. RMON monitors traffic passing through the router and segment traffic not destined for the router.
Setting the RMON Alarm To set an alarm on any MIB object, use the rmon alarm or rmon hc-alarm command in GLOBAL CONFIGURATION mode. • Set an alarm on any MIB object.
CONFIGURATION mode [no] rmon event number [log] [trap community] [description string] [owner string] • number: assigned event number, which is identical to the eventIndex in the eventTable in the RMON MIB. The value must be an integer from 1 to 65,535 and be unique in the RMON Event Table. • log: (Optional) generates an RMON log entry when the event is triggered and sets the eventType in the RMON MIB to log or logand-trap. Default is no log.
[no] rmon collection history {controlEntry integer} [owner ownername] [buckets bucket-number] [interval seconds] • controlEntry: specifies the RMON group of statistics using a value. • integer: a value from 1 to 65,535 that identifies the RMON group of statistics. The value must be a unique index in the RMON History Table. • owner: (Optional) specifies the name of the owner of the RMON group of statistics. The default is a null-terminated string.
44 Rapid Spanning Tree Protocol (RSTP) The Rapid Spanning Tree Protocol (RSTP) is a Layer 2 protocol — specified by IEEE 802.1w — that is essentially the same as spanningtree protocol (STP) but provides faster convergence and interoperability with switches configured with STP and multiple spanning tree protocol (MSTP). Protocol Overview RSTP is a Layer 2 protocol — specified by IEEE 802.
• Dell EMC Networking OS supports only one Rapid Spanning Tree (RST) instance. • All interfaces in virtual local area networks (VLANs) and all enabled interfaces in Layer 2 mode are automatically added to the RST topology. • Adding a group of ports to a range of VLANs sends multiple messages to the rapid spanning tree protocol (RSTP) task, avoid using the range command. When using the range command, Dell EMC Networking recommends limiting the range to five ports and 40 VLANs.
no shutdown DellEMC(conf-if-gi-1/1)# Enabling Rapid Spanning Tree Protocol Globally Enable RSTP globally on all participating bridges; it is not enabled by default. When you enable RSTP, all physical and port-channel interfaces that are enabled and in Layer 2 mode are automatically part of the RST topology. • Only one path from any bridge to any other bridge is enabled. • Bridges block a redundant path by disabling one of the link ports.
Figure 102. Rapid Spanning Tree Enabled Globally To view the interfaces participating in RSTP, use the show spanning-tree rstp command from EXEC privilege mode. If a physical interface is part of a port channel, only the port channel is listed in the command output. DellEMC#show spanning-tree rstp Root Identifier has priority 32768, Address 0001.e801.cbb4 Root Bridge hello time 2, max age 20, forward delay 15, max hops 0 Bridge Identifier has priority 32768, Address 0001.e801.
Designated bridge has priority 32768, address 0001.e801.cbb4 Designated port id is 128.379, designated path cost 0 Number of transitions to forwarding state 1 BPDU : sent 121, received 5 The port is not in the Edge port mode Port 380 (GigabitEthernet 2/4) is designated Forwarding Port path cost 20000, Port priority 128, Port Identifier 128.380 Designated root has priority 32768, address 0001.e801.cbb4 Designated bridge has priority 32768, address 0001.e801.cbb4 Designated port id is 128.
The following table displays the default values for RSTP. Table 68.
Enabling SNMP Traps for Root Elections and Topology Changes To enable SNMP traps, use the following command. • Enable SNMP traps for RSTP, MSTP, and PVST+ collectively. snmp-server enable traps xstp Modifying Interface Parameters On interfaces in Layer 2 mode, you can set the port cost and port priority values. • Port cost — a value that is based on the interface type. The previous table lists the default values. The greater the port cost, the less likely the port is selected to be a forwarding port.
• Assign a number as the bridge priority or designate it as the primary or secondary root. PROTOCOL SPANNING TREE RSTP mode bridge-priority priority-value • priority-value The range is from 0 to 65535. The lower the number assigned, the more likely this bridge becomes the root bridge. The default is 32768. Entries must be multiples of 4096. Example of the bridge-priority Command A console message appears when a new root bridge has been assigned.
interface GigabitEthernet 2/1 no ip address switchport spanning-tree rstp edge-port shutdown DellEMC(conf-if-gi-2/1)# Configuring Fast Hellos for Link State Detection Use RSTP fast hellos to achieve sub-second link-down detection so that convergence is triggered faster. The standard RSTP link-state detection mechanism does not offer the same low link-state detection speed. To achieve sub-second link-down detection so that convergence is triggered faster, use RSTP fast hellos.
45 Software-Defined Networking (SDN) The Dell EMC Networking OS supports software-defined networking (SDN). For more information, see the SDN Deployment Guide.
46 Security This chapter describes several ways to provide security to the Dell EMC Networking system. For details about all the commands described in this chapter, refer to the Security chapter in the Dell EMC Networking OS Command Reference Guide.
• Monitoring AAA Accounting (optional) Enabling AAA Accounting The aaa accounting command allows you to create a record for any or all of the accounting functions monitored. To enable AAA accounting, use the following command. • Enable AAA accounting and create a record for monitoring the accounting function.
Example of Configuring AAA Accounting to Track EXEC and EXEC Privilege Level Command Use In the following sample configuration, AAA accounting is set to track all usage of EXEC commands and commands on privilege level 15.
NOTE: If a console user logs in with RADIUS authentication, the privilege level is applied from the RADIUS server if the privilege level is configured for that user in RADIUS, whether you configure RADIUS authorization. NOTE: RADIUS and TACACS servers support VRF-awareness functionality. You can create RADIUS and TACACS groups and then map multiple servers to a group. The group to which you map multiple servers is bound to a single VRF.
3 Assign a method-list-name or the default list to the terminal line. LINE mode login authentication {method-list-name | default} To view the configuration, use the show config command in LINE mode or the show running-config in EXEC Privilege mode. NOTE: Dell EMC Networking recommends using the none method only as a backup. This method does not authenticate users. The none and enable methods do not work with secure shell (SSH).
The following example shows enabling local authentication for console and remote authentication for the VTY lines. DellEMC(config)# aaa authentication enable mymethodlist radius tacacs DellEMC(config)# line vty 0 9 DellEMC(config-line-vty)# enable authentication mymethodlist Server-Side Configuration Using AAA authentication, the switch acts as a RADIUS or TACACS+ client to send authentication requests to a TACACS+ or RADIUS server.
Obscuring Passwords and Keys By default, the service password-encryption command stores encrypted passwords. For greater security, you can also use the service obscure-passwords command to prevent a user from reading the passwords and keys, including RADIUS, TACACS+ keys, router authentication strings, VRRP authentication by obscuring this information. Passwords and keys are stored encrypted in the configuration file and by default are displayed in the encrypted form when the configuration is displayed.
After you configure other privilege levels, enter those levels by adding the level parameter after the enable command or by configuring a user name or password that corresponds to the privilege level. For more information about configuring user names, refer to Configuring a Username and Password. By default, commands in Dell EMC Networking OS are assigned to different privilege levels. You can access those commands only if you have access to that privilege level.
Configuring the Enable Password Command To configure Dell EMC Networking OS, use the enable command to enter EXEC Privilege level 15. After entering the command, Dell EMC Networking OS requests that you enter a password. Privilege levels are not assigned to passwords, rather passwords are assigned to a privilege level. You can always change a password for any privilege level. To change to a different privilege level, enter the enable command, then the privilege level.
• 2 Secret: Specify the secret for the user. Configure a password for privilege level. CONFIGURATION mode enable password [level level] [encryption-mode] password Configure the optional and required parameters: • level level: specify a level from 0 to 15. Level 15 includes all levels. • encryption-type: enter 0 for plain text or 7 for encrypted text. • password: enter a string up to 32 characters long. To change only the password for the enable command, configure only the password parameter.
The following example shows the Telnet session for user john. The show privilege command output confirms that john is in privilege level 8. In EXEC Privilege mode, john can access only the commands listed. In CONFIGURATION mode, john can access only the snmpserver commands. apollo% telnet 172.31.1.53 Trying 172.31.1.53... Connected to 172.31.1.53. Escape character is '^]'.
EXEC Privilege mode enable or enable privilege-level • If you do not enter a privilege level, Dell EMC Networking OS sets it to 15 by default. Move to a lower privilege level. EXEC Privilege mode disable level-number • level-number: The level-number you wish to set. If you enter disable without a level-number, your security level is 1. RADIUS Remote authentication dial-in user service (RADIUS) is a distributed client/server protocol.
Idle Time Every session line has its own idle-time. If the idle-time value is not changed, the default value of 30 minutes is used. RADIUS specifies idle-time allow for a user during a session before timeout. When a user logs in, the lower of the two idle-time values (configured or default) is used. The idle-time value is updated if both of the following happens: • The administrator changes the idle-time of the line on which the user has logged in.
• Monitoring RADIUS (optional) For a complete listing of all Dell EMC Networking OS commands related to RADIUS, refer to the Security chapter in the Dell EMC Networking OS Command Reference Guide. NOTE: RADIUS authentication and authorization are done in a single step. Hence, authorization cannot be used independent of authentication. However, if you have configured RADIUS authorization and have not configured authentication, a message is logged stating this.
Specifying a RADIUS Server Host When configuring a RADIUS server host, you can set different communication parameters, such as the UDP port, the key password, the number of retries, and the timeout. To specify a RADIUS server host and configure its communication parameters, use the following command. • Enter the host name or IP address of the RADIUS server host.
• Configure the number of times Dell EMC Networking OS retransmits RADIUS requests. CONFIGURATION mode radius-server retransmit retries • • retries: the range is from 0 to 100. Default is 3 retries. Configure the time interval the system waits for a RADIUS server host response. CONFIGURATION mode radius-server timeout seconds • seconds: the range is from 0 to 1000. Default is 5 seconds.
4 Log in to switch using console or telnet or ssh with a valid user role. When 1-factor authentication is used, the authentication succeeds enabling you to access the switch. When two-factor authentication is used, the system prompts you to enter a one-time password as a second step of authentication. If a valid one-time password is supplied, the authentication succeeds enabling you to access the switch.
The following tables describe the various types of attributes that identify the NAS and the user sessions: Table 69. NAS Identification Attributes Attribute code Attribute Description 4 NAS-IP-Address IPv4 address of the NAS. 95 NAS-IPv6–Address IPv6 address of the NAS. Table 70. Change of Authorization (CoA) Attribute Attribute code Attribute Description 5 NAS-Port Port associated with the session to be processed for EAP or MAB users or the VTY ID for AAA sessions. Table 71.
Error-cause Values It is possible that a Dynamic Authorization Server cannot honor Disconnect Message request or CoA request packets for some reason. The Error-Cause Attribute provides more detail on the cause of the problem. It may be included within CoA-Nak and Disconnect-Nak packets.
• rejects the CoA-Request containing NAS-IP-Address or NAS-IPV6-Address attribute that does not match the NAS with a CoA-Nak; Error-Cause value is “NAS Identification Mismatch” (403). • responds with a CoA-Nak, if it is configured to prohibit honoring of corresponding CoA-Request messages; Error-Cause value is “Administratively Prohibited” (501). NOTE: The Administratively Prohibited Error-Cause is also applicable to following scenarios: • if the dot1x feature is not enabled in the NAS-port.
• responds with DM-Nak for any internal processing error in NAS; Error-Cause value is “Resources Unavailable” (506). • ignores attributes that are supported as per RFC but are irrelevant to the DM operation. • responds to a disconnect message containing one or more incorrect attributes values with a Disconnect-NAK; Error-Cause value is “Invalid Attribute Value” (407). • responds to a disconnect message containing unsupported attributes with DM-Nak; Error-Cause value is “Unsupported Attributes” (401).
• Shared key is configured in NAS for DAC. • NAS server listens on the Management IP UDP port 3799 (default) or the port configured through CLI. • AAA session for the user is active. NAS uses the user-name or both the user-name as well as the NAS-Port attribute to identify the AAA user session. NAS disconnects all sessions related to the user, if the user-name is provided without NAS-port.
• discards the packet, if simultaneous requests are received for the same NAS Port. Configuring CoA to re-authenticate 802.1x sessions Dell EMC Networking OS provides RADIUS extension commands that enables you to configure re-authentication of 802.1x user sessions. When you configure this feature, the DAC sends the CoA request to re-authenticate the 802.1x uer session when ever the authorization level of the user’s profile changes. Before configuring re-authentication of 802.
NAS uses the calling-station-id or the NAS-port attributes to identify the 802.1x session. In case of the EAP and MAB users, the callingstation-id is the MAC address of the supplicant and the NAS-port attribute is the interface identifier. Using these atrributes, the NAS retrieves the supplicant that is connected to the interface. 1 Enter the following command to configure the dynamic authorization feature: radius dynamic-auth 2 Enter the following command to terminate the 802.
• sends a CoA-Nak with an error-cause value of 506 (resource unavailable), if it is not able to disable the 802.1x enabled port. • discards the packet, if simultaneous requests are received for the same NAS Port. Important points to remember Virtual link truncking (VLT) scenario This section describes how the secondary NAS processes the PE port authorization RADIUS requests to the primary NAS.
NAS considers the rate limit change value from the next interval period. The range is from 10 to 60 packets per minute. The default is 30 packets per minute. Dell(conf-dynamic-auth#)rate-limit 50 Configuring time-out value You can configure a time-out value for the back-end task to respond to CoA or DM requests. This setting enables the DAS to determine the amount of time to wait before a back-end response is received. The default value is 10 minutes.
The TACACS+ method must not be the last method specified. 3 Enter LINE mode. CONFIGURATION mode line {aux 0 | console 0 | vty number [end-number]} 4 Assign the method-list to the terminal line. LINE mode login authentication {method-list-name | default} Example of a Failed Authentication To view the configuration, use the show config in LINE mode or the show running-config tacacs+ command in EXEC Privilege mode.
debug tacacs+ TACACS+ Remote Authentication The system takes the access class from the TACACS+ server. Access class is the class of service that restricts Telnet access and packet sizes. If you have configured remote authorization, the system ignores the access class you have configured for the VTY line and gets this access class information from the TACACS+ server. The system must know the username and password of the incoming user before it can fetch the access class from the server.
Password: DellEMC# Command Authorization The AAA command authorization feature configures Dell EMC Networking OS to send each configuration command to a TACACS server for authorization before it is added to the running configuration. By default, the AAA authorization commands configure the system to check both EXEC mode and CONFIGURATION mode commands. Use the no aaa authorization config-commands command to enable only EXEC mode command checking.
Specifying an SSH Version The following example uses the ip ssh server version 2 command to enable SSH version 2 and the show ip ssh command to confirm the setting. DellEMC(conf)#ip ssh server version 2 DellEMC(conf)#do show ip ssh SSH server : enabled. SSH server version : v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128-ctr,aes192ctr,aes256-ctr. SSH server macs : hmac-md5,hmac-md5-96,hmac-sha1,hmac-sha1-96,hmac-sha2-256,hmacsha2-256-96.
• ip ssh hostbased-authentication enable : enable host-based authentication for the SSHv2 server. • ip ssh password-authentication enable : enable password authentication for the SSH server. • ip ssh pub-key-file : specify the file the host-based authentication uses. • ip ssh rhostsfile : specify the rhost file the host-based authorization uses. • ip ssh rsa-authentication enable : enable RSA authentication for the SSHv2 server. • ip ssh rsa-authentication : add keys for the RSA authentication.
Configuring the SSH Server Key Exchange Algorithm To configure the key exchange algorithm for the SSH server, use the ip ssh server kex key-exchange-algorithm command in CONFIGURATION mode. key-exchange-algorithm : Enter a space-delimited list of key exchange algorithms that will be used by the SSH server.
• hmac-md5-96 When FIPS is enabled, the default HMAC algorithm is hmac-sha2-256,hmac-sha1,hmac-sha1-96. Example of Configuring a HMAC Algorithm The following example shows you how to configure a HMAC algorithm list. DellEMC(conf)# ip ssh server mac hmac-sha1-96 Configuring the SSH Server Cipher List To configure the cipher list supported by the SSH server, use the ip ssh server cipher cipher-list command in CONFIGURATION mode.
Example of Enabling SSH Password Authentication To view your SSH configuration, use the show ip ssh command from EXEC Privilege mode. DellEMC(conf)#ip ssh server enable DellEMC(conf)#ip ssh password-authentication enable DellEMC# show ip ssh SSH server : enabled. SSH server version : v1 and v2. SSH server vrf : default. SSH server ciphers : 3des-cbc,aes128-cbc,aes192-cbc,aes256-cbc,aes128-ctr,aes192ctr,aes256-ctr. SSH server macs : hmac-md5,hmac-md5-96,hmac-sha1,hmac-sha1-96,hmac-sha2-256,hmacsha2-256-96.
Refer to the first example. 3 Create a list of IP addresses and usernames that are permitted to SSH in a file called rhosts. Refer to the second example. 4 Copy the file shosts and rhosts to the Dell EMC Networking system. 5 Disable password authentication and RSA authentication, if configured CONFIGURATION mode or EXEC Privilege mode no ip ssh password-authentication or no ip ssh rsa-authentication 6 Enable host-based authentication.
Example of Client-Based SSH Authentication DellEMC#ssh 10.16.127.201 ? -c Encryption cipher to use (for v2 clients only) -l User name option -m HMAC algorithm to use (for v2 clients only) -p SSH server port option (default 22) -v SSH protocol version Troubleshooting SSH To troubleshoot SSH, use the following information. You may not bind id_rsa.pub to RSA authentication while logged in via the console. In this case, this message displays:%Error: No username set for this term.
• VTY Line Remote Authentication and Authorization VTY Line Local Authentication and Authorization retrieves the access class from the local database. To use this feature: 1 Create a username. 2 Enter a password. 3 Assign an access class. 4 Enter a privilege level. You can assign line authentication on a per-VTY basis; it is a simple password authentication, using an access-class as authorization. Configure local authentication globally and configure access classes on a per-user basis.
DellEMC(config-line-vty)#end (same applies for radius and line authentication) VTY MAC-SA Filter Support supports MAC access lists which permit or deny users based on their source MAC address. With this approach, you can implement a security policy based on the source MAC address. To apply a MAC ACL on a VTY line, use the same access-class command as IP ACLs. The following example shows how to deny incoming connections from subnet 10.0.0.0 without displaying a login prompt.
Overview of RBAC With Role-Based Access Control (RBAC), access and authorization is controlled based on a user’s role. Users are granted permissions based on their user roles, not on their individual user ID. User roles are created for job functions and through those roles they acquire the permissions to perform their associated job function. Each user can be assigned only a single role. Many users can have the same role. The Dell EMC Networking OS supports the constrained RBAC model.
You must specify at least local authentication. For consistency, the best practice is to define the same authentication method list across all lines, in the same order of comparison; for example VTY and console port. You could also use the default authentication method to apply to all the LINES; for example, console port and VTY. NOTE: The authentication method list must be in the same order as the authorization method list.
netoperator netadmin Exec Config Interface Router IP Route-map Protocol MAC secadmin Exec Config Line sysadmin Exec Config Interface Line Router IP Route-map Protocol MAC User Roles This section describes how to create a new user role and configure command permissions and contains the following topics.
Verify that the user role, myrole, has inherited the security administrator permissions. The output highlighted in bold indicates that the user role has successfully inherited the security administrator permissions.
The following example allows the security administrator (secadmin) to access Interface mode.
In the following example the command protocol permissions are reset to their original setting or one or more of the system-defined roles and any roles that inherited permissions from them. DellEMC(conf)#role configure reset protocol Adding and Deleting Users from a Role To create a user name that is authenticated based on a user role, use the username name password encryption-type password role role-name command in CONFIGURATION mode.
Configure AAA Authorization for Roles Authorization services determine if the user has permission to use a command in the CLI. Users with only privilege levels can use commands in privilege-or-role mode (the default) provided their privilege level is the same or greater than the privilege level of those commands. Users with defined roles can use commands provided their role is permitted to use those commands. Role inheritance is also used to determine authorization.
login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 5 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 6 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 7 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 8 login authentication ucraaa authorization exec ucraaa accounting commands role netadmin line vty 9 login authenticat
Role Accounting This section describes how to configure role accounting and how to display active sessions for roles. This sections consists of the following topics: • Configuring AAA Accounting for Roles • Applying an Accounting Method to a Role • Displaying Active Accounting Sessions for Roles Configuring AAA Accounting for Roles To configure AAA accounting for roles, use the aaa accounting command in CONFIGURATION mode.
• Displaying Information About Roles Logged into the Switch • Displaying Active Accounting Sessions for Roles Displaying User Roles To display user roles using the show userrole command in EXEC Privilege mode, use the show userroles and show users commands in EXEC privilege mode.
Two Factor Authentication (2FA) Two factor authentication also known as 2FA, strengthens the login security by providing one time password (OTP) in addition to username and password. 2FA supports RADIUS authentications with Console, Telnet, and SSHv2. To perform 2FA, follow these steps: • When the Network access server (NAS) prompts for the username and password, provide the inputs. • If the credentials are valid: • • RADIUS server sends a request to the SMS–OTP daemon to generate an OTP for the user.
Hostbased Authentication : disabled. RSA Authentication : disabled. Challenge Response Auth : enabled. Vty Encryption HMAC 2 aes128-cbc hmac-md5 4 aes128-cbc hmac-md5 * 5 aes128-cbc hmac-md5 DellEMC# Remote IP 10.16.127.141 10.16.127.141 10.16.127.141 SMS-OTP Mechanism A short message service one time password (SMS-OTP) is a free RADIUS module to implement two factor authentication. There are multiple 2FA mechanisms that can be deployed with the RADIUS.
ICMPv4 message types Timestamp reply (14) Information request (15) Information reply (16) Address mask request (17) Address mask reply (18) NOTE: The Dell EMC Networking OS does not suppress the ICMP message type echo request (8). Table 76.
Dell EMC Networking OS Security Hardening The security of a network consists of multiple factors. Apart from access to the device, best practices, and implementing various security features, security also lies with the integrity of the device. If the software itself is compromised, all of the aforementioned methods become ineffective. The Dell EMC Networking OS is enhanced verify whether the OS image and the startup configuration file are altered before loading.
After enabling and configuring OS image hash verification, the device verifies the hash checksum of the OS boot image during every reload. DellEMC# verified boot hash system-image A: 619A8C1B7A2BC9692A221E2151B9DA9E Image Verification for Subsequent OS Upgrades After enabling OS image hash verification, for subsequent Dell EMC Networking OS upgrades, you must enter the hash checksum of the new OS image file.
CONFIGURATION mode verified boot 2 Generate the hash checksum for your startup configuration file. EXEC Privilege generate hash {md5 | sha1 | sha256} {flash://filename | startup-config} 3 Verify the hash checksum of the current startup configuration on the local file system. EXEC Privilege verified boot hash startup—config hash-value NOTE: The verified boot hash command is only applicable for the startup configuration file in the local file system.
Enabling User Lockout for Failed Login Attempts You can configure the system to lock out local users for a specific period for unsuccessful login attempts. This feature enhances the security of the switch by locking out the local user account if there are more number of unsuccessful login attempts than what is configured using the max-retry parameter. To enable the user lock out feature, use the following commands: Enable the user lockout feature.
47 Service Provider Bridging Service provider bridging provides the ability to add a second VLAN ID tag in an Ethernet frame and is referred to as VLAN stacking in the Dell EMC Networking OS. VLAN Stacking VLAN stacking, also called Q-in-Q, is defined in IEEE 802.1ad — Provider Bridges, which is an amendment to IEEE 802.1Q — Virtual Bridged Local Area Networks. It enables service providers to use 802.
Figure 103. VLAN Stacking in a Service Provider Network Important Points to Remember • Interfaces that are members of the Default VLAN and are configured as VLAN-Stack access or trunk ports do not switch untagged traffic. To switch traffic, add these interfaces to a non-default VLAN-Stack-enabled VLAN. • Dell EMC Networking cautions against using the same MAC address on different customer VLANs, on the same VLAN-Stack VLAN.
2 Assign access and trunk ports to a VLAN (Creating Access and Trunk Ports). 3 Enabling VLAN-Stacking for a VLAN. Related Configuration Tasks • Configuring the Protocol Type Value for the Outer VLAN Tag • Configuring Dell EMC Networking OS Options for Trunk Ports • Debugging VLAN Stacking • VLAN Stacking in Multi-Vendor Networks Creating Access and Trunk Ports To create access and trunk ports, use the following commands.
Enable VLAN-Stacking for a VLAN To enable VLAN-Stacking for a VLAN, use the following command. • Enable VLAN-Stacking for the VLAN. INTERFACE VLAN mode vlan-stack compatible Example of Viewing VLAN Stack Member Status To display the status and members of a VLAN, use the show vlan command from EXEC Privilege mode. Members of a VLAN-Stackingenabled VLAN are marked with an M in column Q.
NOTE: You can add a trunk port to an 802.1Q VLAN as well as a Stacking VLAN only when the TPID 0x8100. 2 Add the port to a 802.1Q VLAN as tagged or untagged. INTERFACE VLAN mode [tagged | untagged] Example of Configuring a Trunk Port as a Hybrid Port and Adding it to Stacked VLANs In the following example, GigabitEthernet 1/1 is a trunk port that is configured as a hybrid port and then added to VLAN 100 as untagged VLAN 101 as tagged, and VLAN 103, which is a stacking VLAN.
DellEMC#debug member port gigabitethernet 2/4 vlan id : 603 (MT), 100(T), 101(NU) DellEMC# VLAN Stacking in Multi-Vendor Networks The first field in the VLAN tag is the tag protocol identifier (TPID), which is 2 bytes. In a VLAN-stacking network, after the frame is double tagged, the outer tag TPID must match the TPID of the next-hop system. While 802.1Q requires that the inner tag TPID is 0x8100, it does not require a specific value for the outer tag TPID.
Figure 104.
Figure 105.
Figure 106. Single and Double-Tag TPID Mismatch The following table details the outcome of matched and mismatched TPIDs in a VLAN-stacking network with the S-Series. Table 77. Behaviors for Mismatched TPID Network Position Incoming Packet TPID System TPID Match Type Pre-Version 8.2.1.0 Version 8.2.1.
Network Position Incoming Packet TPID System TPID Match Type Pre-Version 8.2.1.0 Version 8.2.1.
Honoring the Incoming DEI Value To honor the incoming DEI value, you must explicitly map the DEI bit to an Dell EMC Networking OS drop precedence. Precedence can have one of three colors. Precedence Description Green High-priority packets that are the least preferred to be dropped. Yellow Lower-priority packets that are treated as best-effort. Red Lowest-priority packets that are always dropped (regardless of congestion status).
Gi 2/9 Gi 2/10 Yellow Yellow 0 0 Dynamic Mode CoS for VLAN Stacking One of the ways to ensure quality of service for customer VLAN-tagged frames is to use the 802.1p priority bits in the tag to indicate the level of QoS desired. When an S-Tag is added to incoming customer frames, the 802.1p bits on the S-Tag may be configured statically for each customer or derived from the C-Tag using Dynamic Mode CoS. Dynamic Mode CoS maps the C-Tag 802.1p value to a S-Tag 802.1p value. Figure 107.
Likewise, in the following configuration, packets with dot1p priority 0–3 are marked as dot1p 7 in the outer tag and queued to Queue 3. Rate policing is according to qos-policy-input 3. All other packets will have outer dot1p 0 and hence are queued to Queue 1. They are therefore policed according to qos-policy-input 1.
Layer 2 Protocol Tunneling Spanning tree bridge protocol data units (BPDUs) use a reserved destination MAC address called the bridge group address, which is 01-80C2-00-00-00. Only spanning-tree bridges on the local area network (LAN) recognize this address and process the BPDU.
Dell EMC Networking OS Behavior: In Dell EMC Networking OS versions prior to 8.2.1.0, the MAC address that Dell EMC Networking systems use to overwrite the Bridge Group Address on ingress was non-configurable. The value of the L2PT MAC address was the Dell EMC Networking-unique MAC address, 01-01-e8-00-00-00.
Enabling Layer 2 Protocol Tunneling To enable Layer 2 protocol tunneling, use the following command. 1 Verify that the system is running the default CAM profile. Use this CAM profile for L2PT. EXEC Privilege mode show cam-profile 2 Enable protocol tunneling globally on the system. CONFIGURATION mode protocol-tunnel enable 3 Tunnel BPDUs the VLAN.
4 Set a maximum rate at which the RPM processes BPDUs for L2PT. VLAN STACKING mode protocol-tunnel rate-limit The default is: no rate limiting. The range is from 64 to 320 kbps. Debugging Layer 2 Protocol Tunneling To debug Layer 2 protocol tunneling, use the following command. • Display debugging information for L2PT. EXEC Privilege mode debug protocol-tunnel Provider Backbone Bridging IEEE 802.1ad—Provider Bridges amends 802.1Q—Virtual Bridged Local Area Networks so that service providers can use 802.
48 sFlow sFlow is a standard-based sampling technology embedded within switches and routers which is used to monitor network traffic. It is designed to provide traffic monitoring for high-speed networks with many switches and routers.
hardware sampling rate is backed-off from 512 to 1024. Note that port 1 maintains its sampling rate of 16384; port 1 is unaffected because it maintains its configured sampling rate of 16384.: • If the interface states are up and the sampling rate is not configured on the port, the default sampling rate is calculated based on the line speed. • If the interface states are shut down, the sampling rate is set using the global sampling rate.
By default, the maximum header size of a packet is 128 bytes. When sflow max-header-size extended is enabled, 256 bytes are copied. These bytes are useful for VxLAN, NvGRE, IPv4, and IPv6 tunneled packets. NOTE: Interface mode configuration takes priority. • To reset the maximum header size of a packet, use the following command [no] sflow max-header-size extended • View the maximum header size of a packet.
Displaying Show sFlow Global To view sFlow statistics, use the following command. • Display sFlow configuration information and statistics. EXEC mode show sflow Example of Viewing sFlow Configuration (Global) The first bold line indicates sFlow is globally enabled. DellEMC#show sflow sFlow services are enabled Global default sampling rate: 32768 Global default counter polling interval: 20 1 collectors configured Collector IP addr: 133.33.33.53, Agent IP addr: 133.33.33.
Displaying Show sFlow on a Stack-unit To view sFlow statistics on a specified Stack-unit, use the following command. • Display sFlow configuration information and statistics on the specified interface.
Back-Off Mechanism If the sampling rate for an interface is set to a very low value, the CPU can get overloaded with flow samples under high-traffic conditions. In such a scenario, a binary back-off mechanism gets triggered, which doubles the sampling-rate (halves the number of samples per second) for all interfaces. The backoff mechanism continues to double the sampling-rate until the CPU condition is cleared. This is as per sFlow version 5 draft.
Global default sampling rate: 32768 Global default counter polling interval: 20 Global extended information enabled: none 0 collectors configured 0 UDP packets exported 0 UDP packets dropped 0 sFlow samples collected 0 sFlow samples dropped due to sub-sampling Important Points to Remember • To export extended-gateway data, BGP must learn the IP destination address. • If the IP destination address is not learned via BGP the Dell EMC Networking system does not export extended-gateway data.
49 Simple Network Management Protocol (SNMP) The Simple Network Management Protocol (SNMP) is designed to manage devices on IP networks by monitoring device operation, which might require administrator intervention. NOTE: On Dell EMC Networking routers, standard and private SNMP management information bases (MIBs) are supported, including all Get and a limited number of Set operations (such as set vlan and copy cmd).
• Transceiver Monitoring Protocol Overview Network management stations use SNMP to retrieve or alter management data from network elements. A datum of management information is called a managed object; the value of a managed object can be static or variable. Network elements store managed objects in a database called a management information base (MIB).
In this example, for a specified user and a group, the AES128-CFB algorithm, the authentication password to enable the server to receive packets from the host, and the privacy password to encode the message contents are configured. SHA authentication needs to be used with the AES-CFB128 privacy algorithm only when FIPS is enabled because SHA is then the only available authentication level.
Important Points to Remember • Typically, 5-second timeout and 3-second retry values on an SNMP server are sufficient for both LAN and WAN applications. If you experience a timeout with these values, increase the timeout value to greater than 3 seconds, and increase the retry value to greater than 2 seconds on your SNMP server. • User ACLs override group ACLs. Set up SNMP As previously stated, Dell EMC Networking OS supports SNMP version 1 and version 2 that are community-based security models.
• auth — password privileges. Select this option to set up a user with password authentication. • priv — password and privacy privileges. Select this option to set up a user with password and privacy privileges. To set up user-based security (SNMPv3), use the following commands. • Configure the user with view privileges only (no password or privacy privileges).
Reading Managed Object Values You may only retrieve (read) managed object values if your management station is a member of the same community as the SNMP agent. Dell EMC Networking supports RFC 4001, Textual Conventions for Internet Work Addresses that defines values representing a type of internet address. These values display for ipAddressTable objects using the snmpwalk command. There are several UNIX SNMP commands that read data. • Read the value of a single managed object.
Configuring Contact and Location Information using SNMP You may configure system contact and location information from the Dell EMC Networking system or from the management station using SNMP. To configure system contact and location information from the Dell EMC Networking system and from the management station using SNMP, use the following commands.
• • Dell EMC Networking enterpriseSpecific environment traps — fan, supply, and temperature. Dell EMC Networking enterpriseSpecific protocol traps — bgp, ecfm, stp, and xstp. To configure the system to send SNMP notifications, use the following commands. 1 Configure the Dell EMC Networking system to send notifications to an SNMP server. CONFIGURATION mode snmp-server host ip-address [traps | informs] [version 1 | 2c |3] [community-string] To send trap messages, enter the keyword traps.
RPM_DOWN: RPM 0 down - card removed HOT_FAILOVER: RPM Failover Completed SFM_DISCOVERY: Found SFM 1 SFM_REMOVE: Removed SFM 1 MAJOR_SFM: Major alarm: Switch fabric down MAJOR_SFM_CLR: Major alarm cleared: Switch fabric up MINOR_SFM: MInor alarm: No working standby SFM MINOR_SFM_CLR: Minor alarm cleared: Working standby SFM present TASK SUSPENDED: SUSPENDED - svce:%d - inst:%d - task:%s RPM0-P:CP %CHMGR-2-CARD_PARITY_ERR ABNORMAL_TASK_TERMINATION: CRASH - task:%s %s CPU_THRESHOLD: Cpu %s usage above threshol
Level 7 VLAN 1000 entity Enable entity change traps Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1487406) 4:07:54.06, SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1, SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 4 Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1488564) 4:08:05.64, SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::mib-2.47.2.0.1, SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 5 Trap SNMPv2-MIB::sysUpTime.0 = Timeticks: (1489064) 4:08:10.64, SNMPv2-MIB::snmpTrapOID.
"NOT_REACHABLE: Syslog server 10.11.226.121 (port: 9140) is not reachable" SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 2 Following is the sample audit log message that other syslog servers that are reachable receive: Oct 21 00:46:13: dv-fedgov-s4810-6: %EVL-6-NOT_REACHABLE:Syslog server 10.11.226.121 (port: 9140) is not reachable Following example shows the SNMP trap that is sent when connectivity to the syslog server is resumed: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (10230) 0:01:42.
MIB Object OID Object Values Description • copyDestFileType .1.3.6.1.4.1.6027.3.5.1.1.1.1.5 1 = Dell EMC Networking OS file 2 = running-config 3 = startup-config Specifies the type of file to copy to. • • copyDestFileLocation .1.3.6.1.4.1.6027.3.5.1.1.1.1.6 1 = flash If copySourceFileType is set to running-config or startupconfig, copySrcFileName is not required. If copySourceFileType is running-config or startupconfig, the default copyDestFileLocation is flash.
snmp-server community community-name rw 2 Copy the f10-copy-config.mib MIB from the Dell iSupport web page to the server to which you are copying the configuration file. 3 On the server, use the snmpset command as shown in the following example. snmpset -v snmp-version -c community-name -m mib_path/f10-copy-config.mib force10system-ipaddress mib-object.index {i | a | s} object-value... • Every specified object must have an object value and must precede with the keyword i. Refer to the previous table.
Copying the Startup-Config Files to the Running-Config To copy the startup-config to the running-config from a UNIX machine, use the following command. • Copy the startup-config to the running-config from a UNIX machine. snmpset -c private -v 2c force10system-ip-address copySrcFileType.index i 3 copyDestFileType.index i 2 Examples of Copying Configuration Files from a UNIX Machine The following example shows how to copy configuration files from a UNIX machine using the object name.
snmpset -v 2c -c public -m ./f10-copy-config.mib force10system-ip-address copySrcFileType.index i 3 copyDestFileType.index i 1 copyDestFileName.index s filepath/ filename copyDestFileLocation.index i 3 copyServerAddress.index a server-ip-address Example of Copying Configuration Files via TFTP From a UNIX Machine .snmpset -v 2c -c private -m ./f10-copy-config.mib 10.10.10.10 copySrcFileType.4 i 3 copyDestFileType.4 i 1 copyDestFileLocation.4 i 3 copyDestFileName.4 s /home/myfilename copyServerAddress.4 a 11.
MIB Object OID Values Description 4 = file exists 5 = file not found 6 = timeout 7 = unknown copyEntryRowStatus .1.3.6.1.4.1.6027.3.5.1.1.1.1.15 Row status Specifies the state of the copy operation. Uses CreateAndGo when you are performing the copy. The state is set to active when the copy is completed. Obtaining a Value for MIB Objects To obtain a value for any of the MIB objects, use the following command. • Get a copy-config MIB object value. snmpset -v 2c -c public -m ./f10-copy-config.
MIB Support to Display Reason for Last System Reboot Dell EMC Networking provides MIB objects to display the reason for the last system reboot. The dellNetProcessorResetReason object contains the reason for the last system reboot. The following table lists the related MIB objects. Table 84. MIB Objects for Displaying Reason for Last System Reboot MIB Object OID Description dellNetProcessorResetReason 1.3.6.1.4.1.6027.3.26.1.4.3.1.7 This is the table that contains the reason for last system reboot.
SNMP Walk Example Output snmpwalk -v 2c -c public 10.16.131.156 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.5 SNMPv2-SMI::enterprises.674.10895.3000.1.2.110.7.2.1.5.10 = INTEGER: 48 snmpwalk -v 2c -c public 10.16.131.156 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.6 SNMPv2-SMI::enterprises.674.10895.3000.1.2.110.7.2.1.6.10 = INTEGER: 31 snmpwalk -v 2c -c public 10.16.131.156 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.7 SNMPv2-SMI::enterprises.674.10895.3000.1.2.110.7.2.1.7.
MIB Object OID Description chSysCoresTimeCreated 1.3.6.1.4.1.6027.3.10.1.2.10.1.3 Contains the time at which core files are created. chSysCoresStackUnitNumber 1.3.6.1.4.1.6027.3.10.1.2.10.1.4 Contains information that includes which stack unit or processor the core file was originated from. chSysCoresProcess 1.3.6.1.4.1.6027.3.10.1.2.10.1.5 Contains information that includes the process names that generated each core file.
MIB Object OID Description dellNetFpWredOutOfProfileDrops 1.3.6.1.4.1.6027.3.27.1.3.1.31 Count of WRED drops of red packets. SNMP Walk Example Output snmpwalk -v 2c -c public 10.16.151.246 1.3.6.1.4.1.6027.3.27.1.3 | grep 2107012 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.1.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.2.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.3.2107012 = Counter64: 0 SNMPv2-SMI::enterprises.6027.3.27.1.3.1.4.
MIB Object OID Description dellNetFlashPartitionUsed 1.3.6.1.4.1.6027.3.26.1.4.8.1.4 Contains the amount of space used by the files on the partition. dellNetFlashPartitionFree 1.3.6.1.4.1.6027.3.26.1.4.8.1.5 Contains the amount of free space available on the partition. dellNetFlashPartitionMountPoint 1.3.6.1.4.1.6027.3.26.1.4.8.1.6 Symbolic or Alias name for the partition.
.1.3.6.1.4.1.6027.3.26.1.4.8.1.6.4 = STRING: "/f10/flash" .1.3.6.1.4.1.6027.3.26.1.4.8.1.6.5 = STRING: "/f10/phonehome" MIB Support to Display Egress Queue Statistics Dell EMC Networking OS provides MIB objects to display the information of the packets transmitted or dropped per unicast or multicast egress queue. The following table lists the related MIB objects: Table 90. MIB Objects to display egress queue statistics MIB Object OID Description dellNetFpEgrQTxPacketsRate 1.3.6.1.4.1.6027.3.27.1.20.1.
SNMPv2-SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.30.1.1.0.24.0.0.0.0 = INTEGER: 1275078656 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.30.1.1.1.32.1.4.30.1.1.1.1.4.30.1.1.1 = INTEGER: 1275078656 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.30.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = INTEGER: 0 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.70.70.70.0.24.0.0.0.0 = INTEGER: 2097157 SNMPv2-SMI::enterprises.6027.3.9.1.5.1.8.1.1.4.70.70.70.1.32.1.4.127.0.0.1.1.4.127.0.0.1 = INTEGER: 0 SNMPv2-SMI::enterprises.
SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.20.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = STRING: "CP" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.30.1.1.0.24.0.0.0.0 = STRING: "CP" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.30.1.1.1.32.1.4.30.1.1.1.1.4.30.1.1.1 = STRING: "Po 20" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.30.1.1.2.32.1.4.127.0.0.1.1.4.127.0.0.1 = STRING: "CP" SNMPv2-SMI::enterprises.6027.3.9.1.5.1.10.1.1.4.70.70.70.0.24.0.0.0.0 = STRING: "CP" SNMPv2-SMI::enterprises.6027.3.9.
SNMPv2-SMI::enterprises.6027.3.9.1.7.0 = Gauge32: 1 SNMPv2-SMI::enterprises.6027.3.9.1.8.0 = Gauge32: 2047 MIB Support for entAliasMappingTable Dell EMC Networking provides a method to map the physical interface to its corresponding ifindex value. The entAliasMappingTable table contains zero or more rows, representing the logical entity mapping and physical component to external MIB identifiers. The following table lists the related MIB objects: Table 92.
Table 93. MIB Objects for LAG MIB Object OID Description lagMIB 1.2.840.10006.300.43 Contains information about link aggregation module for managing 802.3ad. lagMIBObjects 1.2.840.10006.300.43.1 dot3adAgg 1.2.840.10006.300.43.1.1 dot3adAggTable 1.2.840.10006.300.43.1.1.1 Contains information about every Aggregator that is associated with a system. dot3adAggEntry 1.2.840.10006.300.43.1.1.1.1 Contains a list of Aggregator parameters and indexed by the ifIndex of the Aggregator.
MIB Object OID Description dot3adAggPortListTable 1.2.840.10006.300.43.1.1.2 Contains a list of all the ports associated with each Aggregator. Each LACP channel in a device occupies an entry in the table. dot3adAggPortListEntry 1.2.840.10006.300.43.1.1.2.1 Contains a list of ports associated with a given Aggregator and indexed by the ifIndex of the Aggregator. dot3adAggPortListPorts 1.2.840.10006.300.43.1.1.2.1.1 Contains a complete set of ports currently associated with the Aggregator.
Viewing the Details of Reserved Unrecognized LLDP TLVs • To view the information of reserved unrecognized LLDP TLVs using SNMP, use the following commands. snmpwalk -v2c -c mycommunity 10.16.150.83 1.0.8802.1.1.2.1.4 iso.0.8802.1.1.2.1.4.1.1.6.0.2113029.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.3161092.6 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.3161605.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.4209668.6 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.4210181.2 = INTEGER: 5 iso.0.8802.1.1.2.1.4.1.1.6.0.
MIB Object OID Description identify a particular unrecognized organizationally defined information instance. lldpRemOrgDefInfo 1.0.8802.1.1.2.1.4.4.1.4 Contains the string value used to identify the organizationally defined information of the remote system. Viewing the Details of Organizational Specific Unrecognized LLDP TLVs • To view the information of organizational specific unrecognized LLDP TLVs using SNMP, use the following commands. snmpwalk -v2c -c public 10.16.150.83 1.0.8802.1.1.2.1.4.4.1.
MTU 1554 bytes, IP MTU 1500 bytes LineSpeed auto Displaying the Ports in a VLAN Dell EMC Networking OS identifies VLAN interfaces using an interface index number that is displayed in the output of the show interface vlan command. Examples of Viewing VLAN Ports Using SNMP The following example shows viewing the VLAN interface index number using SNMP. DellEMC(conf)#do show interface vlan id 10 % Error: No such interface name.
> snmpget -v2c -c mycommunity 10.11.131.185 .1.3.6.1.2.1.17.7.1.4.3.1.2.1107787786 SNMPv2-SMI::mib-2.17.7.1.4.3.1.2.1107787786 = Hex-STRING: 40 00 00 00 00 00 00 00 00 00 00 The value 40 is in the first set of 7 hex pairs, indicating that these ports are in Stack Unit 1. The hex value 40 is 0100 0000 in binary. As described, the left-most position in the string represents Port 1. The next position from the left represents Port 2 and has a value of 1, indicating that Port 1/2 is in VLAN 10.
Managing Overload on Startup If you are running IS-IS, you can set a specific amount of time to prevent ingress traffic from being received after a reload and allow the routing protocol upgrade process to complete. To prevent ingress traffic on a router while the IS reload is implemented, use the following command. • Set the amount of time after an IS-IS reload is performed before ingress traffic is allowed at startup.
Fetch Dynamic MAC Entries using SNMP Dell EMC Networking supports the RFC 1493 dot1d table for the default VLAN and the dot1q table for all other VLANs. NOTE: The 802.1q Q-BRIDGE MIB defines VLANs regarding 802.1d, as 802.1d itself does not define them. As a switchport must belong a VLAN (the default VLAN or a configured VLAN), all MAC address learned on a switchport are associated with a VLAN. For this reason, the Q-Bridge MIB is used for MAC address query.
Example of Fetching MAC Addresses Learned on a Port-Channel Using SNMP Use dot3aCurAggFdbTable to fetch the learned MAC address of a port-channel. The instance number is the decimal conversion of the MAC address concatenated with the port-channel number.
Table 97. MIB Objects for Viewing the System Image on Flash Partitions MIB Object OID Description MIB chSysSwInPartitionAImgVers 1.3.6.1.4.1.6027.3.10.1.2.8.1.11 List the version string of the system image in Flash Partition A. Chassis MIB chSysSwInPartitionBImgVers 1.3.6.1.4.1.6027.3.10.1.2.8.1.12 List the version string of the system image in Flash Partition B.
• snmp context context2 • timers bgp 30 90 • neighbor 30.1.1.1 remote-as 200 • neighbor 30.1.1.1 no shutdown • exit-address-family To map the context to a VRF instance for SNMPv3, follow these steps: 1 2 Create a community and map a VRF to it. Create a context and map the context and community, to a community map.
SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.2.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.3.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.4.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.2.1.5.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.3.1.1.0.1.30.1.1.2.1.30.1.1.1 SNMPv2-SMI::enterprises.6027.20.1.2.3.3.1.2.0.1.30.1.1.2.1.30.1.1.
IF-MIB::ifIndex.1107755009 = INTEGER: 1107755009 SNMPv2-SMI::enterprises.6027.3.1.1.4.1.2 = STRING: "OSTATE_DN: Changed interface state Po 1" 2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]: SNMPv2-MIB::sysUpTime.0 = Timeticks: (8500932) 23:36:49.32 SNMPv2-MIB::snmpTrapOID.0 = IF-MIB::linkUp IF-MIB::ifIndex.33865785 = INTEGER: 33865785 SNMPv2-SMI::enterprises. 6027.3.1.1.4.1.2 = STRING: "OSTATE_UP: Changed interface state to up: Gi 1/1" 2010-02-10 14:22:40 10.16.130.4 [10.16.130.4]: SNMPv2-MIB::sysUpTime.
SMI::enterprises.6027.3.30.1.1.2 SNMPv2-SMI::enterprises.6027.3.30.1.1 = STRING: "REACHABLE: Syslog server 10.11.226.121 (port: 9140) is reachable"SNMPv2-SMI::enterprises.6027.3.6.1.1.2.0 = INTEGER: 2 Following is the sample audit log message that other syslog servers that are reachable receive: Oct 21 05:26:04: dv-fedgov-s4810-6: %EVL-6-REACHABLE:Syslog server 10.11.226.
Field (OID) Description SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.3 Optics Present SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.4 Optics Type SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.5 Vendor Name SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.6 Part Number SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.7 Serial Number SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.8 Transmit Power Lane1 SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.9 Transmit Power Lane2 SNMPv2-SMI::enterprises.6027.3.11.1.3.1.1.
50 Stacking Using the Dell EMC Networking OS stacking feature, you can interconnect multiple switch units with stacking ports . The stack becomes manageable as a single switch through the stack management unit. The system accepts Unit ID numbers from 1 to 12 and it supports stacking up to twelve units.
Stack Management Roles The stack elects the management units for the stack management. • Stack master — primary management unit, also called the master unit. • Standby — secondary management unit. • Stack units — the remaining units in the stack, also called stack members. The system supports up to twelve stack units. The master holds the control plane and the other units maintain a local copy of the forwarding databases.
Up Time : 43 min, 41 sec Dell Networking OS Version : 1-0(0-4679) Jumbo Capable : yes POE Capable : no FIPS Mode : disabled Burned In MAC : f8:10:20:30:40:97 No Of MACs : 3 -- Module 1 -Status : not present -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------1 1 up UNKNOWN up 0 1 2 absent absent 0 -- Fan Status -Unit Bay TrayStatus Fan1 Speed Fan2 Speed ----------------------------------------------------------------------
POE Capable FIPS Mode Burned In MAC No Of MACs : : : : no disabled f8:12:23:45:56:78 3 -- Module 1 -Status : not present -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------3 1 absent absent 0 3 2 up AC up 0 -- Fan Status -Unit Bay TrayStatus Fan1 Speed Fan2 Speed -----------------------------------------------------------------------------------3 1 up up 6956 up 7058 Speed in RPM -- Unit 4 -Unit Type : Member Unit Stat
When an up and running standalone unit or stack is merged with another stack, based on election, the losing stack reloads and the master unit of the winning stack becomes the master of the merged stack. For more details, see sectionsAdd Units to an Existing Stack and Remove a Unit from a Stack. It is possible to reset individual units to force them to give up the management role or reload the whole stack from the CLI to ensure a fully synchronized bootup.
12 12 1 2 up down AC up UNKNOWN absent NA NA -- Fan Status -Unit Bay TrayStatus Fan1 Speed Fan2 Speed -----------------------------------------------------------------------------------1 1 up up 7164 up 7058 2 1 up up 6956 up 7058 3 1 up up 7164 up 7058 4 1 up up 7058 up 7164 5 1 up up 7058 up 6956 6 1 up up 7058 up 7164 7 1 up up 12307 down 0 8 1 up up 7164 up 7164 9 1 up up 7058 up 7058 10 1 up up 7164 up 7058 11 1 up up 7058 up 7058 12 1 up up 7164 up 7058 Speed in RPM DellEMC# Virtual IP You can m
Example of Adding a Standalone with a Lower MAC Address to a Stack ----------STANDALONE BEFORE CONNECTION--------------Standalone#show system brief Stack MAC Reload-Type : f8:b1:56:29:fc:21 : normal-reload [Next boot : normal-reload] -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports ---------------------------------------------------------------------------------1 Member not present 2 Member not present 3 Member not present 4 Management online S3148P S3148P 1-0(0-4679) 54 5 Member not presen
--------------------------------------------------------------------------1 1 not present No Module 0 2 1 not present No Module 0 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------1 1 down UNKNOWN down 0 1 2 up AC up 7728 2 1 absent absent 0 2 2 up AC up 8032 -- Fan Status -Unit Bay TrayStatus Fan0 Speed Fan1 Speed -----------------------------------------------------------------------------------1 1 up up 6666 up 7058 2
9 10 11 12 Member Member Member Member not not not not present present present present -- Module Info -Unit Module No Status Module Type Ports --------------------------------------------------------------------------1 1 not present No Module 0 2 1 not present No Module 0 4 1 not present No Module 0 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------1 1 down UNKNOWN down 0 1 2 up AC up 7728 2 1 absent absent 0 2 2 up
Figure 110. Supported Stacking Topologies High Availability on Stacks Stacks have master and standby management units analogous to Dell EMC Networking route processor modules (RPM). The master unit synchronizes the running configuration and protocol states so that the system fails over in the event of a hardware or software fault on the master unit. In such an event, or when the master unit is removed, the standby unit becomes the stack manager and Dell EMC Networking OS elects a new standby unit.
Stack-unit State: Stack-unit SW Version: Link to Peer: Active 1-0(0-4697) Up -- PEER Stack-unit Status ------------------------------------------------Stack-unit State: Standby Peer Stack-unit ID: 2 Stack-unit SW Version: 1-0(0-4697) -- Stack-unit Redundancy Configuration ------------------------------------------------Primary Stack-unit: mgmt-id 1 Auto Data Sync: Full Failover Type: Hot Failover Auto reboot Stack-unit: Enabled Auto failover limit: 3 times in 60 minutes -- Stack-unit Failover Record -----
ssh-peer-stack-unit start telnet-peer-stack-unit terminal upload Dell(standby)# Open a SSH connection to the peer stack-unit Start shell Open a telnet connection to the peer stack-unit Set terminal line parameters Upload file -----------------CONSOLE ACCESS ON A MEMBER---------------------------Dell(stack-member-1)#? reset-self Reset this unit alone show Show running system information You can connect two units with two or more stacking cables in case of a stacking port or cable failure.
stack-unit stack—unit—number priority priority 5 Connect the units using stacking cables. NOTE: There are two fixed mini-SAS stacking connectors on the PSU side. You can connect mini-SAS cables between units to form stacking. 6 Reload the stack one unit at a time. EXEC Privilege mode show system brief Start with the management unit, then the standby, then each of the members in order of their assigned stack number (or the position in the stack you want each unit to take).
-- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------1 Member online S3124F S3124F 1-0(0-4679) 30 2 Member online S3124 S3124 1-0(0-4679) 30 3 Member online S3124 S3124 1-0(0-4679) 30 4 Member online S3148P S3148P 1-0(0-4679) 54 5 Standby online S3148 S3148 1-0(0-4679) 54 6 Member online S3148P S3148P 1-0(0-4679) 54 7 Member online S3124F S3124F 1-0(0-4679) 30 8 Member online S3124P S3124P 1-0(0-4679) 30 9 Member o
6 7 8 9 10 11 12 1 1 1 1 1 1 1 up up up up up up up up up up up up up up 7058 12307 7164 7058 7164 7058 7164 up down up up up up up 7164 0 7164 7058 7058 7058 7058 Speed in RPM DellEMC# Add Units to an Existing Stack You can add units to an existing stack in one of three ways. • By manually assigning a new unconfigured unit a position in an existing stack. • By adding a configured unit to an existing stack. • By merging two stacks.
Unit UnitType Status ReqTyp CurTyp Version Ports --------------------------------------------------------------------------------1 Management online S3148P S3148P 1-0(0-4679) 54 2 Standby online S3148P S3148P 1-0(0-4679) 54 3 Member not present 4 Member not present 5 Member not present 6 Member not present 7 Member not present 8 Member not present 9 Member not present 10 Member not present 11 Member not present 12 Member not present -- Module Info -Unit Module No Status Module Type Ports -------------------
-- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------1 1 up AC up 7888 1 2 down UNKNOWN absent NA 2 1 up AC up NA 2 2 absent absent NA 4 1 absent absent 0 4 2 up AC up 7888 -- Fan Status -Unit Bay TrayStatus Fan1 Speed Fan2 Speed -----------------------------------------------------------------------------------1 1 up up 7164 up 7058 2 1 up up 6956 up 7058 4 1 up up 7058 up 7164 Speed in RPM Dell# Adding a Configured Unit
For a parent stack that is split into two child stacks, A and B, each with multiple units: • If one of the new stacks receives the master and the standby management units, it is unaffected by the split. • If one of the new stacks receives only the master unit, that unit remains the stack manager, and Dell EMC Networking OS elects a new standby management unit.
Displaying Information about a Stack To display information about the stack, use the following command. • Display for stack-identity, status, and hardware information on every unit in a stack. EXEC Privilege mode • show system Display most of the information in show system, but in a more convenient tabular form. EXEC Privilege mode • show system brief Display the same information in show system, but only for the specified unit.
Speed in RPM -- Unit 2 -Unit Type : Standby Unit Status : online Next Boot : online Required Type : S3124 - 28-port GE/TE (S3100) Current Type : S3124 - 28-port GE/TE (S3100) Master priority : 13 Hardware Rev : 5.
The following is an example of the show system brief command to view the stack summary information.
-----------------------------------------------------------------------------------1 1 up up 7164 up 6956 2 1 up up 7058 up 7058 3 1 up up 6956 up 7058 4 1 up up 6956 up 6956 5 1 up up 7058 up 7058 6 1 up up 7058 up 7164 7 1 up up 12000 down 0 8 1 up up 7164 up 7164 9 1 up up 7058 up 7058 10 1 up up 6956 up 7164 11 1 up up 7164 up 7164 12 1 up up 7058 up 7058 Speed in RPM DellEMC# The following example shows the show system stack-ports command.
• Influence the selection of the stack management units. CONFIGURATION mode stack-unit unit-number priority priority-value The unit with the numerically highest priority is elected the master management unit, and the unit with the second highest priority is the standby unit. The range is from 1 to 14. The default is 0. Managing Redundancy on a Stack Use the following commands to manage the redundancy on a stack. • Reset the current management unit and make the standby unit the new master unit.
Verify a Stack Configuration The light of the LED status indicator on the front panel of the stack identifies the unit’s role in the stack. • • Off indicates the unit is a stack member. Solid green indicates the unit is the stack master (management unit). Displaying the Status of Stacking Ports To display the status of the stacking ports, including the topology, use the following command. • Display the stacking ports.
Jumbo Capable POE Capable FIPS Mode Boot Flash Boot Selector Memory Size Temperature Voltage Serial Number Part Number Vendor Id Date Code Country Code Piece Part ID PPID Revision Service Tag Expr Svc Code Auto Reboot Burned In MAC No Of MACs : : : : : : : : : : : : : : : : : : : : yes yes disabled 5.2.1.
10 11 12 Member Member Member not present not present not present -- Module Info -Unit Module No Status Module Type Ports --------------------------------------------------------------------------1 1 online S3148P-10GE-2X10BaseT 2 2 1 online S3148P-10GE-2SFP+ 2 3 1 online S3148P-10GE-2X10BaseT 2 -- Power Supplies -Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------1 1 up AC up 7888 1 2 down UNKNOWN absent NA 2 1 up AC up NA 2 2 absent ab
3 1 absent absent 0 3 2 up AC up 7888 -- Fan Status -Unit Bay TrayStatus Fan1 Speed Fan2 Speed -----------------------------------------------------------------------------------2 1 up up 6956 up 7058 3 1 up up 7058 up 7164 Speed in RPM DellEMC# NOTE: Each unit in the stack has a stack number that is either assigned by you or Dell EMC Networking OS. To manually renumber stack members, use the stack-unit old-unit-number renumber new-unit-number command.
Example of Card Problem Error on a Stack - Different Dell EMC Networking OS Versions DellEMC#show system brief Stack MAC Reload-Type : 34:17:17:18:19:1e : normal-reload [Next boot : normal-reload] -- Stack Info -Unit UnitType Status ReqTyp CurTyp Version Ports -----------------------------------------------------------------------------------1 Management online S3148P S3148P 1-0(0-4679) 54 2 Standby online S3148P S3148P 1-0(0-4679) 54 3 Member not present S3124F 4 Member card problem S3148P unknown 5 Memb
51 Storm Control Storm control allows you to control unknown-unicast, muticast, and broadcast traffic on Layer 2 and Layer 3 physical interfaces. Dell EMC Networking Operating System (OS) Behavior: Dell EMC Networking OS supports unknown-unicast, muticast, and broadcast control for Layer 2 and Layer 3 traffic. Dell EMC Networking OS Behavior: The minimum number of packets per second (PPS) that storm control can limit on the device is two.
storm-control multicast packets_per_second in • Shut down the port if it receives the PFC/LLFC packets more than the configured rate. INTERFACE mode storm-control pfc-llfc pps in shutdown NOTE: PFC/LLFC storm control enabled interface disables the interfaces if it receives continuous PFC/LLFC packets. It can be a result of a faulty NIC/Switch that sends spurious PFC/LLFC packets.
52 Spanning Tree Protocol (STP) The spanning tree protocol (STP) is supported on Dell EMC Networking OS.
Configure Spanning Tree Configuring spanning tree is a two-step process.
Configuring Interfaces for Layer 2 Mode All interfaces on all switches that participate in spanning tree must be in Layer 2 mode and enabled. Figure 112. Example of Configuring Interfaces for Layer 2 Mode To configure and enable the interfaces for Layer 2, use the following command. 1 If the interface has been assigned an IP address, remove it. INTERFACE mode no ip address 2 Place the interface in Layer 2 mode. INTERFACE switchport 3 Enable the interface.
Example of the show config Command To verify that an interface is in Layer 2 mode and enabled, use the show config command from INTERFACE mode. DellEMC(conf-if-gi-1/1)#show config ! interface GigabitEthernet 1/1 no ip address switchport no shutdown DellEMC(conf-if-gi-1/1)# Enabling Spanning Tree Protocol Globally Enable the spanning tree protocol globally; it is not enabled by default.
no disable Examples of Verifying Spanning Tree Information To disable STP globally for all Layer 2 interfaces, use the disable command from PROTOCOL SPANNING TREE mode. To verify that STP is enabled, use the show config command from PROTOCOL SPANNING TREE mode.
Adding an Interface to the Spanning Tree Group To add a Layer 2 interface to the spanning tree topology, use the following command. • Enable spanning tree on a Layer 2 interface. INTERFACE mode spanning-tree 0 Modifying Global Parameters You can modify the spanning tree parameters. The root bridge sets the values for forward-delay, hello-time, and max-age and overwrites the values set on other bridges participating in STP.
• Change the max-age parameter (the refresh interval for configuration information that is generated by recomputing the spanning tree topology). PROTOCOL SPANNING TREE mode max-age seconds The range is from 6 to 40. The default is 20 seconds. To view the current values for global parameters, use the show spanning-tree 0 command from EXEC privilege mode. Refer to the second example in Enabling Spanning Tree Protocol Globally.
• Enable PortFast on an interface. INTERFACE mode spanning-tree stp-id portfast [bpduguard | [shutdown-on-violation]] Example of Verifying PortFast is Enabled on an Interface To verify that PortFast is enabled on a port, use the show spanning-tree command from EXEC Privilege mode or the show config command from INTERFACE mode. Dell EMC Networking recommends using the show config command.
Figure 114. Enabling BPDU Guard Dell EMC Networking OS Behavior: BPDU guard and BPDU filtering both block BPDUs, but are two separate features. BPDU guard: • • is used on edgeports and blocks all traffic on edgeport if it receives a BPDU. drops the BPDU after it reaches the RP and generates a console message.
The secondary option specifies a bridge priority of 16384. The default is 32768. Example of Viewing STP Root Information To view only the root information, use the show spanning-tree root command from EXEC privilege mode. DellEMC#show spanning-tree 0 root Root ID Priority 32768, Address 0001.e80d.2462 We are the root of the spanning tree Root Bridge hello time 2, max age 20, forward delay 15 DellEMC# STP Root Guard Use the STP root guard feature in a Layer 2 network to avoid bridging loops.
Figure 115. STP Root Guard Prevents Bridging Loops Configuring Root Guard Enable STP root guard on a per-port or per-port-channel basis. Dell EMC Networking OS Behavior: The following conditions apply to a port enabled with STP root guard: • Root guard is supported on any STP-enabled port or port-channel interface except when used as a stacking port.
• mstp: enables root guard on an MSTP-enabled port. • rstp: enables root guard on an RSTP-enabled port. • pvst: enables root guard on a PVST-enabled port. To disable STP root guard on a port or port-channel interface, use the no spanning-tree 0 rootguard command in an interface configuration mode. To verify the STP root guard configuration on a port or port-channel interface, use the show spanning-tree 0 guard [interface interface] command in a global configuration mode.
As shown in the following illustration (STP topology 2, upper right), a loop can also be created if the forwarding port on Switch B becomes busy and does not forward BPDUs within the configured forward-delay time. As a result, the blocking port on Switch C transitions to a forwarding state, and both Switch A and Switch C transmit traffic to Switch B (STP topology 2, lower right).
• Loop guard is supported on any STP-enabled port or port-channel interface. • Loop guard is supported on a port or port-channel in any spanning tree mode: • Spanning Tree Protocol (STP) • Rapid Spanning Tree Protocol (RSTP) • Multiple Spanning Tree Protocol (MSTP) • Per-VLAN Spanning Tree Plus (PVST+) • You cannot enable root guard and loop guard at the same time on an STP port.
53 SupportAssist SupportAssist sends troubleshooting data securely to Dell. SupportAssist in this Dell EMC Networking OS release does not support automated email notification at the time of hardware fault alert, automatic case creation, automatic part dispatch, or reports. SupportAssist requires Dell EMC Networking OS 9.9(0.0) and SmartScripts 9.7 or later to be installed on the Dell EMC Networking device. For more information on SmartScripts, see Dell EMC Networking Open Automation guide. Figure 117.
Configuring SupportAssist Using a Configuration Wizard You are guided through a series of queries to configure SupportAssist. The generated commands are added to the running configuration, including the DNS resolve commands, if configured. This command starts the configuration wizard for the SupportAssist. At any time, you can exit by entering Ctrl-C. If necessary, you can skip some data entry. Enable the SupportAssist service.
making such transfers, Dell shall ensure appropriate protection is in place to safeguard the Collected Data being transferred in connection with SupportAssist. If you are downloading SupportAssist on behalf of a company or other legal entity, you are further certifying to Dell that you have appropriate authority to provide this consent on behalf of that entity.
support-assist activity {full-transfer | core-transfer} start now DellEMC#support-assist activity full-transfer start now DellEMC#support-assist activity core-transfer start now Configuring SupportAssist Activity SupportAssist Activity mode allows you to configure and view the action-manifest file for a specific activity. To configure SupportAssist activity, use the following commands. 1 Move to the SupportAssist Activity mode for an activity.
action-manifest remove DellEMC(conf-supportassist-act-full-transfer)#action-manifest remove custom_file1.json DellEMC(conf-supportassist-act-full-transfer)# DellEMC(conf-supportassist-act-event-transfer)#action-manifest remove custom_event_file1.json DellEMC(conf-supportassist-act-event-transfer)# 6 Enable a specific SupportAssist activity. By default, the full transfer includes the core files. When you disable the core transfer activity, the full transfer excludes the core files.
Configuring SupportAssist Person SupportAssist Person mode allows you to configure name, email addresses, phone, method and time zone for contacting the person. SupportAssist Person configurations are optional for the SupportAssist service. To configure SupportAssist person, use the following commands. 1 Configure the contact name for an individual.
[no] server server-name DellEMC(conf-supportassist)#server default DellEMC(conf-supportassist-serv-default)# 2 Configure a proxy for reaching the SupportAssist remote server. SUPPORTASSIST SERVER mode [no] proxy-ip-address {ipv4-address | ipv6-address}port port-number [ username userid password [encryption-type] password ] DellEMC(conf-supportassist-serv-default)#proxy-ip-address 10.0.0.
show running-config support-assist DellEMC# show running-config support-assist ! support-assist enable all ! activity event-transfer enable action-manifest install default ! activity core-transfer enable ! contact-company name Dell street-address F lane , Sector 30 address city Brussels state HeadState country Belgium postalcode S328J3 ! contact-person first Fred last Nash email-address primary des@sed.com alternate sed@dol.
54 System Time and Date System time and date settings and the network time protocol (NTP) are supported on Dell EMC Networking OS. You can set system times and dates and maintained through the NTP. They are also set through the Dell EMC Networking Operating System (OS) command line interfaces (CLIs) and hardware settings. The Dell EMC Networking OS supports reaching an NTP server through different VRFs. You can configure a maximum of eight logging servers across different VRFs or the same VRF.
Following conventions established by the telephone industry [BEL86], the accuracy of each server is defined by a number called the stratum, with the topmost level (primary servers) assigned as one and each level downwards (secondary servers) in the hierarchy assigned as one greater than the preceding level. Dell EMC Networking OS synchronizes with a time-serving host to get the correct time. You can set Dell EMC Networking OS to poll specific NTP time-serving hosts for the current time.
Related Configuration Tasks • Configuring NTP Broadcasts • Disabling NTP on an Interface • Configuring a Source IP Address for NTP Packets (optional) Enabling NTP NTP is disabled by default. To enable NTP, specify an NTP server to which the Dell EMC Networking system synchronizes. To specify multiple servers, enter the command multiple times. You may specify an unlimited number of servers at the expense of CPU resources. • Specify the NTP server to which the Dell EMC Networking system synchronizes.
Disabling NTP on an Interface By default, NTP is enabled on all active interfaces. If you disable NTP on an interface, Dell EMC Networking OS drops any NTP packets sent to that interface. To disable NTP on an interface, use the following command. • Disable NTP on the interface. INTERFACE mode ntp disable To view whether NTP is configured on the interface, use the show config command in INTERFACE mode. If ntp disable is not listed in the show config command output, NTP is enabled.
To configure NTP authentication, use the following commands. 1 Enable NTP authentication. CONFIGURATION mode ntp authenticate 2 Set an authentication key. CONFIGURATION mode ntp authentication-key number md5 key Configure the following parameters: • • 3 number: the range is from 1 to 4294967295. This number must be the same as the number in the ntp trusted-key command. key: enter a text string. This text string is encrypted. Define a trusted key.
1w6d23h : NTP: rcv packet from 192.168.1.1 leap 0, mode 4, version 3, stratum 1, ppoll 1024 rtdel 0000 (0.000000), rtdsp AF587 (10959.090820), refid 4C4F434C (76.79.67.76) ref CD7E14FD.43F7CED9 (16:29:49.265 UTC Wed Apr 1 2009) org CD7F5368.D0535000 (15:8:24.813 UTC Thu Apr 2 2009) rec CD7F5368.D0000000 (15:8:24.812 UTC Thu Apr 2 2009) xmt CD7F5368.D0000000 (15:8:24.812 UTC Thu Apr 2 2009) inp CD7F5368.D1974000 (15:8:24.
Dell EMC Networking OS Time and Date You can set the time and date using the Dell EMC Networking OS CLI. Configuration Task List The following is a configuration task list for configuring the time and date settings.
• offset: enter one of the following: • a number from 1 to 23 as the number of hours in addition to UTC for the timezone. • a minus sign (-) then a number from 1 to 23 as the number of hours.
Setting Recurring Daylight Saving Time Set a date (and time zone) on which to convert the switch to daylight saving time on a specific day every year. If you have already set daylight saving for a one-time setting, you can set that date and time as the recurring setting with the clock summer-time time-zone recurring command. To set a recurring daylight saving time, use the following command. • Set the clock to the appropriate timezone and adjust to daylight saving time every year.
first Week number to start last Week number to start DellEMC(conf)#clock summer-time pacific recurring DellEMC(conf)#02:10:57: %RPM0-P:CP %CLOCK-6-TIME CHANGE: Summertime configuration changed from "Summer time starts 00:00:00 Pacific Tue Mar 14 2017 ; Summer time ends 00:00:00 pacific Tue Nov 7 2017" to "Summer time starts 02:00:00 Pacific Tue Mar 14 2017;Summer time ends 02:00:00 pacific Tue Nov 7 2017" Configuring a Custom-defined Period for NTP time Synchronization You can configure the system to
55 Tunneling Tunnel interfaces create a logical tunnel for IPv4 or IPv6 traffic. Tunneling supports RFC 2003, RFC 2473, and 4213. DSCP, hop-limits, flow label values, open shortest path first (OSPF) v2, and OSPFv3 are supported. Internet control message protocol (ICMP) error relay, PATH MTU transmission, and fragmented packets are not supported.
no ip address ipv6 address 2::1/64 tunnel destination 90.1.1.1 tunnel source 60.1.1.1 tunnel mode ipv6ip no shutdown The following sample configuration shows a tunnel configured in IPIP mode (IPv4 tunnel carries IPv4 and IPv6 traffic): DellEMC(conf)#interface tunnel 3 DellEMC(conf-if-tu-3)#tunnel source 5::5 DellEMC(conf-if-tu-3)#tunnel destination 8::9 DellEMC(conf-if-tu-3)#tunnel mode ipv6 DellEMC(conf-if-tu-3)#ip address 3.1.1.
The following sample configuration shows how to use the interface tunnel configuration commands. DellEMC(conf-if-gi-1/1)#show config ! interface GigabitEthernet 1/1 ip address 20.1.1.1/24 ipv6 address 20:1::1/64 no shutdown DellEMC(conf)#interface tunnel 1 DellEMC(conf-if-tu-1)#ip unnumbered gigabitethernet 1/1 DellEMC(conf-if-tu-1)#ipv6 unnumbered gigabitethernet 1/1 DellEMC(conf-if-tu-1)#tunnel source 40.1.1.
! interface Tunnel 1 ip address 1.1.1.1/24 ipv6 address 1abd::1/64 tunnel source anylocal tunnel allow-remote 40.1.1.
56 Uplink Failure Detection (UFD) Uplink failure detection (UFD) provides detection of the loss of upstream connectivity and, if used with network interface controller (NIC) teaming, automatic recovery from a failed link. Feature Description A switch provides upstream connectivity for devices, such as servers. If a switch loses its upstream connectivity, downstream devices also lose their connectivity.
Figure 119. Uplink Failure Detection How Uplink Failure Detection Works UFD creates an association between upstream and downstream interfaces. The association of uplink and downlink interfaces is called an uplink-state group. An interface in an uplink-state group can be a physical interface or a port-channel (LAG) aggregation of physical interfaces. An enabled uplink-state group tracks the state of all assigned upstream interfaces.
Figure 120. Uplink Failure Detection Example If only one of the upstream interfaces in an uplink-state group goes down, a specified number of downstream ports associated with the upstream interface are put into a Link-Down state. You can configure this number and is calculated by the ratio of the upstream port bandwidth to the downstream port bandwidth in the same uplink-state group.
• • • If one of the upstream interfaces in an uplink-state group goes down, either a user-configurable set of downstream ports or all the downstream ports in the group are put in an Operationally Down state with an UFD Disabled error. The order in which downstream ports are disabled is from the lowest numbered port to the highest.
4 (Optional) Enable auto-recovery so that UFD-disabled downstream ports in the uplink-state group come up when a disabled upstream port in the group comes back up. UPLINK-STATE-GROUP mode downstream auto-recover The default is auto-recovery of UFD-disabled downstream ports is enabled. To disable auto-recovery, use the no downstream auto-recover command. 5 (Optional) Enter a text description of the uplink-state group.
3/50 02:36:43: 3/51 02:36:43: 02:36:43: 02:36:43: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Downstream interface set to UFD error-disabled: Te %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Te 3/49 %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Te 3/50 %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Te 3/51 02:37:29: %RPM0-P:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state to down: Gi 1/7 02:37:29: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: G
• group-id: The values are from 1 to 16. Examples of Viewing UFD Information (S50) The following example shows viewing the uplink state group status.
0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts 0 Multicasts, 0 Broadcasts, 0 Unicasts 0 throttles, 0 discarded, 0 collisions Rate info (interval 299 seconds): Input 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Output 00.00 Mbits/sec, 0 packets/sec, 0.00% of line-rate Time since last interface status change: 00:01:23 The following example shows viewing the UFD configuration.
DellEMC# 00:13:06: %STKUNIT0-M:CP %SYS-5-CONFIG_I: Configured from console by console DellEMC# show running-config uplink-state-group ! uplink-state-group 3 description Testing UFD feature downstream disable links 2 downstream GigabitEthernet 1/1-2,5,9,11-12 upstream GigabitEthernet 1/3-4 DellEMC# show uplink-state-group 3 Uplink State Group: 3 Status: Enabled, Up DellEMC# show uplink-state-group detail (Up): Interface up (Dwn): Interface down (Dis): Interface disabled Uplink State Group : 3 Status: Enabled
57 Upgrade Procedures To find the upgrade procedures, go to the Dell EMC Networking OS Release Notes for your system type to see all the requirements needed to upgrade to the desired Dell EMC Networking OS version. To upgrade your system type, follow the procedures in the Dell EMC Networking OS Release Notes. You can download the release notes of your platform at http://www.force10networks.com. Use your login ID to log in to the website.
58 Virtual LANs (VLANs) Virtual LANs (VLANs) are a logical broadcast domain or logical grouping of interfaces in a local area network (LAN) in which all data received is kept locally and broadcast to all members of the group. When in Layer 2 mode, VLANs move traffic at wire speed and can span multiple devices. The system supports up to 4093 port-based VLANs and one default VLAN, as specified in IEEE 802.1Q.
Default VLAN When you configure interfaces for Layer 2 mode, they are automatically placed in the Default VLAN as untagged interfaces. Only untagged interfaces can belong to the Default VLAN. The following example displays the outcome of placing an interface in Layer 2 mode. To configure an interface for Layer 2 mode, use the switchport command.
VLANs and Port Tagging To add an interface to a VLAN, the interface must be in Layer 2 mode. After you place an interface in Layer 2 mode, the interface is automatically placed in the Default VLAN. supports IEEE 802.1Q tagging at the interface level to filter traffic. When you enable tagging, a tag header is added to the frame after the destination and source MAC addresses. That information is preserved as the frame moves through the network.
• Configure a port-based VLAN (if the VLAN-ID is different from the Default VLAN ID) and enter INTERFACE VLAN mode. CONFIGURATION mode interface vlan vlan-id To activate the VLAN, after you create a VLAN, assign interfaces in Layer 2 mode to the VLAN. Example of Verifying a Port-Based VLAN To view the configured VLANs, use the show vlan command in EXEC Privilege mode.
Codes: * - Default VLAN, G - GVRP VLANs NUM Status Q * 1 Inactive 2 Active T T 3 Active T T Ports Po1(So 0/0-1) Gi 1/1 Po1(So 0/0-1) Gi 1/2 DellEMC#config DellEMC(conf)#interface vlan 4 DellEMC(conf-if-vlan)#tagged po 1 DellEMC(conf-if-vlan)#show conf ! interface Vlan 4 no ip address tagged Port-channel 1 DellEMC(conf-if-vlan)#end DellEMC#show vlan Codes: * - Default VLAN, G - GVRP VLANs NUM Status Q * 1 Inactive 2 Active T T 3 Active T T 4 Active T Ports Po1(So 0/0-1) Gi 1/1 Po1(So 0/0-1) Gi 1/2 Po1(So
Codes: * - Default VLAN, G - GVRP VLANs NUM * 1 2 Status Active Active 3 Active Q U T T T T Ports Gi 1/2 Po1(So 0/0-1) Gi 1/3 Po1(So 0/0-1) Gi 1/1 4 Inactive DellEMC#conf DellEMC(conf)#interface vlan 4 DellEMC(conf-if-vlan)#untagged gigabitethernet 1/2 DellEMC(conf-if-vlan)#show config ! interface Vlan 4 no ip address untagged GigabitEthernet 1/2 DellEMC(conf-if-vlan)#end DellEMC#show vlan Codes: * - Default VLAN, G - GVRP VLANs NUM * 1 2 3 4 Status Q Inactive Active T T Active T T Active U Ports Po
Native VLAN support breaks this barrier so that you can connect a port to both VLAN-aware and VLAN-unaware stations. Such ports are referred to as hybrid ports. Physical and port-channel interfaces may be hybrid ports. Native VLAN is useful in deployments where a Layer 2 port can receive both tagged and untagged traffic on the same physical port. The classic example is connecting a voice-over-IP (VOIP) phone and a PC to the same port of the switch.
59 Virtual Link Trunking (VLT) Virtual link trunking (VLT) is a Dell EMC technology that provides two Dell EMC switches the ability to function as a single switch. VLT allows physical links between two Dell EMC switches to appear as a single virtual link to the network core or other switches such as Edge, Access, or top-of-rack (ToR). As a result, the two physical switches appear as a single switch to the connected devices.
Figure 123. VLT providing multipath VLT reduces the role of spanning tree protocols (STPs) by allowing link aggregation group (LAG) terminations on two separate distribution or core switches and supporting a loop-free topology. To prevent the initial loop that may occur prior to VLT being established, use a spanning tree protocol. After VLT is established, you may use rapid spanning tree protocol (RSTP) to prevent loops from forming with new links that are incorrectly connected and outside the VLT domain.
Figure 124. Example of VLT Deployment VLT offers the following benefits: • Allows a single device to use a LAG across two upstream devices. • Eliminates STP-blocked ports. • Provides a loop-free topology. • Uses all available uplink bandwidth. • Provides fast convergence if either the link or a device fails. • Optimized forwarding with virtual router redundancy protocol (VRRP). • Provides link-level resiliency. • Assures high availability. • Active-Active load sharing with VRRP.
VLT Terminology The following are key VLT terms. • Virtual link trunk (VLT) — The combined port channel between an attached device and the VLT peer switches. • VLT backup link — The backup link monitors the connectivity between the VLT peer switches. The backup link sends configurable, periodic keep alive messages between the VLT peer switches. • VLT interconnect (VLTi) — The link used to synchronize states between the VLT peer switches.
Layer-2 Traffic in VLT Domains In a VLT domain, the MAC address of any host connected to the VLT peers is synchronized between the VLT nodes. In the following example, VLAN 10 is spanned across three VLT domains. Figure 125. Layer-2 Traffic in VLT Domains If Host 1 from a VLT domain sends a frame to Host 2 in another VLT domain, the frame can use any link shown to reach Host 2.
30 30 30 30 30 30 a0:00:a1:00:00:07 a0:00:a1:00:00:08 a0:00:a1:00:00:09 a0:00:a1:00:00:0a a0:00:a1:00:00:0b a0:00:a1:00:00:0c Dynamic Dynamic Dynamic Dynamic Dynamic Dynamic (N) Po 11 Active (N) Po 11 Active (N) Po 11 Active (N) Po 11 Active (N) Po 11 Active Po 11 Active VLT-10-PEER-2#show vlt statistics mac VLT MAC Statistics -------------------L2 Info Pkts sent:0, L2 Mac-sync Pkts Sent:7 L2 Info Pkts Rcvd:0, L2 Mac-sync Pkts Rcvd:9 L2 Reg Request sent:0 L2 Reg Request rcvd:0 L2 Reg Response sent:0 L2
Figure 126. VLT on Core Switches The aggregation layer is mostly in the L2/L3 switching/routing layer. For better resiliency in the aggregation, Dell EMC Networking recommends running the internal gateway protocol (IGP) on the VLTi VLAN to synchronize the L3 routing table across the two nodes on a VLT system. Enhanced VLT Enhanced VLT (eVLT)) refers to the ability to connect two VLT domains.
Figure 127. Enhanced VLT Configure Virtual Link Trunking VLT requires that you enable the feature and then configure the same VLT domain, backup link, and VLT interconnect on both peer switches. Important Points to Remember • You cannot enable stacking simultaneously with VLT. If you enable both at the same time, unexpected behavior can occur. • VLT port channel interfaces must be switch ports. • If you include RSTP on the system, configure it before VLT. Refer to Configure Rapid Spanning Tree.
• When you enable IGMP snooping on the VLT peers, ensure the value of the delay-restore command is not less than the query interval. • When you enable Layer 3 routing protocols on VLT peers, make sure the delay-restore timer is set to a value that allows sufficient time for all routes to establish adjacency and exchange all the L3 routes between the VLT peers before you enable the VLT ports.
• • Each VLT domain has a unique MAC address that you create or VLT creates automatically. • ARP tables are synchronized between the VLT peer nodes. • VLT peer switches operate as separate chassis with independent control and data planes for devices attached on non-VLT ports. • One device in the VLT domain is assigned a primary role; the other device takes the secondary role. The primary and secondary roles are required for scenarios when connectivity between the chassis is lost.
• • • In the backup link between peer switches, heartbeat messages are exchanged between the two chassis for health checks. The default time interval between heartbeat messages over the backup link is 1 second. You can configure this interval. The range is from 1 to 5 seconds. DSCP marking on heartbeat messages is CS6.
• Software features not supported with VLT • • • • In a VLT domain, the following software features are not supported on VLT ports: 802.1x, GVRP, and VXLAN. VLT and VRRP interoperability • In a VLT domain, VRRP interoperates with virtual link trunks that carry traffic to and from access devices (see Overview). The VLT peers belong to the same VRRP group and are assigned master and backup roles. Each peer actively forwards L3 traffic, reducing the traffic flow over the VLT interconnect.
addresses to be re-learned. However, enabling RSTP can detect potential loops caused by non-system issues such as cabling errors or incorrect configurations. To minimize possible topology changes after link or node failure, RSTP is useful for potential loop detection. Configure RSTP using the following specifications.
• Statistics and Counters — Statistical and counter information displays IPv6 information when applicable. • Heartbeat — You can configure an IPv4 or IPv6 address as a backup link destination. You cannot use an IPv4 and an IPv6 address simultaneously. VLT Port Delayed Restoration When a VLT node boots up, if the VLT ports have been previously saved in the start-up configuration, they are not immediately enabled.
Figure 128. PIM-Sparse Mode Support on VLT On each VLAN where the VLT peer nodes act as the first hop or last hop routers, one of the VLT peer nodes is elected as the PIM designated router. If you configured IGMP snooping along with PIM on the VLT VLANs, you must configure VLTi as the static multicast router port on both VLT peer switches. This ensures that for first hop routers, the packets from the source are redirected to the designated router (DR) if they are incorrectly hashed.
Each VLT peer runs its own PIM protocol independently of other VLT peers. To ensure the PIM protocol states or multicast routing information base (MRIB) on the VLT peers are synced, if the incoming interface (IIF) and outgoing interface (OIF) are Spanned, the multicast route table is synced between the VLT peers. To verify the PIM neighbors on the VLT VLAN and on the multicast port, use the show ip pim neighbor, show ip igmp snooping mrouter, and show running config commands.
Figure 129. Packets without peer routing enabled If you enable peer routing, a VLT node acts as a proxy gateway for its connected VLT peer as shown in the image below. Even though the gateway address of the packet is different, Peer-1 routes the packet to its destination on behalf of Peer-2 to avoid sub-optimal routing. Figure 130. Packets with peer routing enabled Benefits of Peer Routing • • Avoids sub-optimal routing • Reduces latency by avoiding another hop in the traffic path.
• You can reduce the number of VLTi port channel members based on your specific design. With peer routing, you need not configure VRRP for the participating VLANs. As both VLT nodes act as a gateway for its peer, irrespective of the gateway IP address, the traffic flows upstream without any latency. There is no limitation for the number of VLANS. VLT Unicast Routing VLT unicast routing is a type of VLT peer routing that locally routes unicast packets destined for the L3 endpoint of the VLT peer.
The advantages of syncing the multicast routes between VLT peers are: • VLT resiliency — After a VLT link or peer failure, if the traffic hashes to the VLT peer, the traffic continues to be routed using multicast until the PIM protocol detects the failure and adjusts the multicast distribution tree. • Optimal routing — The VLT peer that receives the incoming traffic can directly route traffic to all downstream routers connected on VLT ports.
RSTP Configuration RSTP is supported in a VLT domain. Before you configure VLT on peer switches, configure RSTP in the network. RSTP is required for initial loop prevention during the VLT startup phase. You may also use RSTP for loop prevention in the network outside of the VLT port channel. For information about how to configure RSTP, Rapid Spanning Tree Protocol (RSTP). Run RSTP on both VLT peer switches.
Configure RSTP on VLT Peers to Prevent Forwarding Loops (VLT Peer 1) Dell_VLTpeer1(conf)#protocol spanning-tree rstp Dell_VLTpeer1(conf-rstp)#no disable Dell_VLTpeer1(conf-rstp)#bridge-priority 4096 Configure RSTP on VLT Peers to Prevent Forwarding Loops (VLT Peer 2) Dell_VLTpeer2(conf)#protocol spanning-tree rstp Dell_VLTpeer2(conf-rstp)#no disable Dell_VLTpeer2(conf-rstp)#bridge-priority 0 Configuring VLT To configure VLT, use the following procedure.
3 Add one or more port interfaces to the port channel. INTERFACE PORT-CHANNEL mode channel-member interface interface: specify one of the following interface types: 4 • For a 1-GigabitEthernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. Ensure that the port channel is active.
VLT DOMAIN CONFIGURATION mode primary-priority value The priority values are from 1 to 65535. The default is 32768. If the primary peer fails, the secondary peer (with the higher priority) takes the primary role. If the primary peer (with the lower priority) later comes back online, it is assigned the secondary role (there is no preemption). 6 (Optional) Prevent a possible loop during the bootup of a VLT peer switch or a device that accesses the VLT domain.
CONFIGURATION mode vlt domain domain-id The range of domain IDs from 1 to 1000. 2 Enter an amount of time, in seconds, to delay the restoration of the VLT ports after the system is rebooted. CONFIGURATION mode delay-restore delay-restore-time The range is from 1 to 1200. The default is 90 seconds. Reconfiguring the Default VLT Settings (Optional) To reconfigure the default VLT settings, use the following commands. 1 Enter VLT-domain configuration mode for a specified VLT domain.
Connecting a VLT Domain to an Attached Access Device (Switch or Server) To connect a VLT domain to an attached access device, use the following commands. On a VLT peer switch: To connect to an attached device, configure the same port channel ID number on each peer switch in the VLT domain. 1 Configure the same port channel to be used to connect to an attached device and enter interface configuration mode. CONFIGURATION mode interface port-channel id-number 2 Remove an IP address from the interface.
The range of domain IDs is from 1 to 1000. 2 Enter the port-channel number that acts as the interconnect trunk. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number 3 Enter the VLAN ID number of the VLAN where the VLT forwards packets received on the VLTi from an adjacent peer that is down. VLT DOMAIN CONFIGURATION mode peer-down-vlan vlan interface number Configuring Enhanced VLT (Optional) To configure enhanced VLT (eVLT) between two VLT domains on your network, use the following procedure.
The format is aaaa.bbbb.cccc. Also reconfigure the same MAC address on the VLT peer switch. Use this command to minimize the time required for the VLT system to synchronize the default MAC address of the VLT domain on both peer switches when one peer switch reboots. 7 When you create a VLT domain on a switch, Dell EMC Networking OS automatically assigns a unique unit ID (0 or 1) to each peer switch. To explicitly configure the default values on each peer switch, use the following command.
16 Enable peer routing. VLT DOMAIN CONFIGURATION mode peer-routing If you enable peer routing, a VLT node acts as the proxy gateway for its peer. 17 Repeat steps 1 through 16 for the VLT peer node in Domain 1. 18 Repeat steps 1 through 16 for the first VLT node in Domain 2. 19 Repeat steps 1 through 16 for the VLT peer node in Domain 2. To verify the configuration of a VLT domain, use any of the show commands described in Verifying a VLT Configuration.
show running-config entity 12 Verify that VLT is running. EXEC mode show vlt brief or show vlt detail 13 Verify that the VLT LAG is running in both VLT peer units. EXEC mode or EXEC Privilege mode show interfaces interface Example of Configuring VLT In the following sample VLT configuration steps, VLT peer 1 is Dell-2, VLT peer 2 is Dell-4, and the ToR is S60-1.
2 Configure the VLT peer link port channel id in VLT peer 1 and VLT peer 2. 3 In the Top of Rack unit, configure LACP in the physical ports (shown for VLT peer 1 only. Repeat steps for VLT peer 2. The bold vltpeer-lag port-channel 2 indicates that port-channel 2 is the port-channel id configured in VLT peer 2).
Role Role Priority ICL Link Status HeartBeat Status VLT Peer Status Version Local System MAC address Remote System MAC address Remote system version Delay-Restore timer Delay-Restore Abort Threshold Peer-Routing Peer-Routing-Timeout timer Multicast peer-routing timeout DellEMC# : : : : : : : : : : Secondary 32768 Up Up Up 6(3) 00:01:e8:8a:e9:91 00:01:e8:8a:e9:76 6(3) 90 seconds : : : : 60 seconds Disabled 0 seconds 150 seconds Verify that the VLT LAG is up in VLT peer unit.
Configure both ends of the VLT interconnect trunk with identical PVST+ configurations. When you enable VLT, the show spanningtree pvst brief command output displays VLT information. DellEMC#show spanning-tree pvst vlan 1000 brief VLAN 1000 Executing IEEE compatible Spanning Tree Protocol Root ID Priority 0, Address 90b1.1cf4.9b79 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 0, Address 90b1.1cf4.
Figure 131. Peer Routing Configuration Example Dell-1 Switch Configuration In the following output, RSTP is enabled with a bridge priority of 0. This ensures that Dell-1 becomes the root bridge. DellEMC#1#show run | find protocol protocol spanning-tree pvst no disable vlan 1,20,800,900 bridge-priority 0 The following output shows the existing VLANs.
The following is the configuration in interfaces: DellEMC#1#sh run int ma0/0 interface ManagementEthernet 0/0 description Used_for_VLT_Keepalive ip address 10.10.10.1/24 no shutdown (The management interfaces are part of a default VRF and are isolated from the switch’s data plane.) In Dell-1, te 0/0 and te 0/1 are used for VLTi.
Port channel 2 connects the access switch A1. DellEMC#1#sh run int po2 interface Port-channel 2 description port-channel_to_access_switch_A1 no ip address portmode hybrid switchport vlt-peer-lag port-channel 2 no shutdown Vlan 20 is used in Dell-1, Dell-2, and R1 to form OSPF adjacency. When OSPF is converged, the routing tables in all devices are synchronized. DellEMC#1#sh run int vlan 20 interface Vlan 20 description OSPF PEERING VLAN ip address 192.168.20.
----------------Destination: Peer HeartBeat status: Destination VRF: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.10.10.2 Up default 1 3 34998 4 5 Use the show vlt detail command to verify that VLT is functional and that the correct VLANs are allowed.
Verify if peer routing has populated the CAM table with the correct information using the show cam mac command.
no ip address no shutdown The following example shows that te 0/0 and te 0/1 are included in port channel 10. Also note that configuration on the VLTi links does not contain the switchport command. Dell-2#sh run int po10 interface Port-channel 10 description VLTi Port-Channel no ip address channel-member TenGigabitEthernet 0/0-1 no shutdown Te 0/4 connects to the access switch A1.
tagged Port-channel 2 no shutdown The following output shows Dell-2 is configured with VLT domain 1. The peer-link port-channel command makes port channel 10 as the VLTi link. The peer-routing command enables peer routing between VLT peers in VLT domain 1. The IP address configured with the backupdestination command is the management IP address of the VLT peer (Dell-1). A priority value of 55000 makes Dell-2 as the secondary VLT peer.
network 192.168.8.0/24 area 0 network 192.168.9.0/24 area 0 network 172.16.1.0/24 area 0 network 192.168.20.0/29 area 0 passive-interface default no passive-interface vlan 20 While the passive-interface default command prevents all interfaces from establishing an OSPF neighborship, the no passive-interface vlan 20 command allows the interface for VLAN 20, the OSPF peering VLAN, to establish OSPF adjacencies. The following output displays that Dell-1 forms neighborship with Dell-2 and R1.
! interface Loopback4 ip address 4.4.4.2 255.255.255.0 R1#show run int port-channel 1 interface Port-channel1 switchport ip address 192.168.20.3 255.255.255.248 R1#show run | find router router ospf 1 router-id 172.15.1.1 passive-interface default no passive-interface Port-channel1 network 2.2.2.0 0.0.0.255 area 0 network 3.3.3.0 0.0.0.255 area 0 network 4.4.4.0 0.0.0.255 area 0 (The above subnets correspond to loopback interfaces lo2, lo3 and lo4.
This default route is configured for testing purposes, as described in the next section. The access switch (A1) is used to generate ICMP test PINGs to a loopback interface on CR1. This default route points to DellEMC#2’s VLAN 800 SVI interface. It’s in place to ensure that routed test traffic has DellEMC#2’s MAC address as the destination address in the Ethernet frame’s header When A1 sends a packet to R1, the VLT peers act as the default gateway for each other.
Domain_1_Peer1(conf-if-po-100)# vlt-peer-lag port-channel 100 Domain_1_Peer1(conf-if-po-100)# no shutdown Add links to the eVLT port-channel on Peer 1. Domain_1_Peer1(conf)#interface range gigabitethernet 1/16 - 1/17 Domain_1_Peer1(conf-if-range-gi-1/16-17)# port-channel-protocol LACP Domain_1_Peer1(conf-if-range-gi-1/16-17)# port-channel 100 mode active Domain_1_Peer1(conf-if-range-gi-1/16-17)# no shutdown Next, configure the VLT domain and VLTi on Peer 2.
Domain_1_Peer4#no shutdown Domain_2_Peer4(conf)#vlt domain 200 Domain_2_Peer4(conf-vlt-domain)# peer-link port-channel 1 Domain_2_Peer4(conf-vlt-domain)# back-up destination 10.18.130.12 Domain_2_Peer4(conf-vlt-domain)# system-mac mac-address 00:0b:00:0b:00:0b Domain_2_Peer4(conf-vlt-domain)# peer-routing Domain_2_Peer4(conf-vlt-domain)# unit-id 1 Configure eVLT on Peer 4.
Verifying a VLT Configuration To monitor the operation or verify the configuration of a VLT domain, use any of the following show commands on the primary and secondary VLT switches. • Display information on backup link operation. EXEC mode • show vlt backup-link Display general status information about VLT domains currently configured on the switch.
HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 3 34998 1026 1025 Dell_VLTpeer2# show vlt backup-link VLT Backup Link ----------------Destination: Peer HeartBeat status: HeartBeat Timer Interval: HeartBeat Timeout: UDP Port: HeartBeat Messages Sent: HeartBeat Messages Received: 10.11.200.20 Up 1 3 34998 1030 1014 The following example shows the show vlt brief command.
VLT Role ---------VLT Role: System MAC address: System Role Priority: Local System MAC address: Local System Role Priority: Secondary 00:01:e8:8a:df:bc 32768 00:01:e8:8a:df:e6 32768 The following example shows the show running-config vlt command. Dell_VLTpeer1# show running-config vlt ! vlt domain 30 peer-link port-channel 60 back-up destination 10.11.200.18 Dell_VLTpeer2# show running-config vlt ! vlt domain 30 peer-link port-channel 60 back-up destination 10.11.200.
Executing IEEE compatible Spanning Tree Protocol Root ID Priority 0, Address 0001.e88a.dff8 Root Bridge hello time 2, max age 20, forward delay 15 Bridge ID Priority 0, Address 0001.e88a.dff8 We are the root Configured hello time 2, max age 20, forward delay 15 Interface Designated Name PortID Prio Cost Sts Cost Bridge ID PortID ---------- -------- ---- ------- -------- - ------- ------------Po 1 128.2 128 200000 DIS 0 0 0001.e88a.dff8 128.2 Po 3 128.4 128 200000 DIS 0 0 0001.e88a.dff8 128.4 Po 4 128.
NUM Status Description Q Ports 10 Active U Po110(Te 1/51) T Po100(Te 1/49,50) Configuring Virtual Link Trunking (VLT Peer 2) Enable VLT and create a VLT domain with a backup-link VLT interconnect (VLTi). Dell_VLTpeer2(conf)#vlt domain 999 Dell_VLTpeer2(conf-vlt-domain)#peer-link port-channel 100 Dell_VLTpeer2(conf-vlt-domain)#back-up destination 10.11.206.23 Dell_VLTpeer2(conf-vlt-domain)#exit Configure the backup link.
Troubleshooting VLT To help troubleshoot different VLT issues that may occur, use the following information. NOTE: For information on VLT Failure mode timing and its impact, contact your Dell EMC Networking representative. Table 102. Troubleshooting VLT Description Behavior at Peer Up Behavior During Run Time Action to Take Bandwidth monitoring A syslog error message and an SNMP trap is generated when the VLTi bandwidth usage goes above the 80% threshold and when it drops below 80%.
Description Behavior at Peer Up Behavior During Run Time Action to Take information, refer to the Release Notes for this release. VLT LAG ID is not configured on one VLT peer A syslog error message is generated. The peer with the VLT configured remains active. A syslog error message is generated. The peer with the VLT configured remains active. Verify the VLT LAG ID is configured correctly on both VLT peers. VLT LAG ID mismatch The VLT port channel is brought down.
Keep the following points in mind when you configure VLT nodes in a PVLAN: • Configure the VLTi link to be in trunk mode. Do not configure the VLTi link to be in access or promiscuous mode. • You can configure a VLT LAG or port channel to be in trunk, access, or promiscuous port modes when you include the VLT LAG in a PVLAN. The VLT LAG settings must be the same on both the peers. If you configure a VLT LAG as a trunk port, you can associate that LAG to be a member of a normal VLAN or a PVLAN.
PVLAN Operations When One VLT Peer is Down When a VLT port moves to the Admin or Operationally Down state on only one of the VLT nodes, the VLT Lag is still considered to be up. All the PVLAN MAC entries that correspond to the operationally down VLT LAG are maintained as synchronized entries in the device. These MAC entries are removed when the peer VLT LAG also becomes inactive or a change in PVLAN configuration occurs.
Table 103.
VLT LAG Mode Peer1 PVLAN Mode of VLT VLAN Peer2 ICL VLAN Membership Mac Synchronization Peer1 Peer2 - Primary VLAN Y - Primary VLAN X No No Promiscuous Access Primary Secondary No No Trunk Access Primary/Normal Secondary No No Configuring a VLT VLAN or LAG in a PVLAN You can configure the VLT peers or nodes in a private VLAN (PVLAN).
7 Enter the port-channel number that acts as the interconnect trunk. VLT DOMAIN CONFIGURATION mode peer-link port-channel id-number 8 (Optional) To configure a VLT LAG, enter the VLAN ID number of the VLAN where the VLT forwards packets received on the VLTi from an adjacent peer that is down.
• Specified with this command even before they have been created. • Amended by specifying the new secondary VLAN to be added to the list. Proxy ARP Capability on VLT Peer Nodes The proxy ARP functionality is supported on VLT peer nodes. A proxy ARP-enabled device answers the ARP requests that are destined for the other router in a VLT domain. The local host forwards the traffic to the proxy ARP-enabled device, which in turn transmits the packets to the destination. By default, proxy ARP is enabled.
When a VLT node detects peer up, it does not perform proxy ARP for the peer IP addresses. IP address synchronization occurs again between the VLT peers. Proxy ARP is enabled only if you enable peer routing on both the VLT peers. If you disable peer routing by using the no peerroutingcommand in VLT DOMAIN node, a notification is sent to the VLT peer to disable the proxy ARP.
INTERFACE PORT-CHANNEL mode vlan-stack {access | trunk} 2 Configure VLAN as VLAN-stack compatible on both the peers. INTERFACE VLAN mode vlan-stack compatible 3 Add the VLT LAG as a member to the VLAN-stack on both the peers. INTERFACE VLAN mode member port-channel port—channel ID 4 Verify the VLAN-stack configurations.
DellEMC#show running-config interface port-channel 20 ! interface Port-channel 20 no ip address switchport vlan-stack trunk vlt-peer-lag port-channel 20 no shutdown DellEMC# Configure the VLAN as a VLAN-Stack VLAN and add the VLT LAG as Members to the VLAN DellEMC(conf)#interface vlan 50 DellEMC(conf-if-vl-50)#vlan-stack compatible DellEMC(conf-if-vl-50-stack)#member port-channel 10 DellEMC(conf-if-vl-50-stack)#member port-channel 20 DellEMC#show running-config interface vlan 50 ! interface Vlan 50 vlan-sta
DellEMC(conf-if-po-10)#no shutdown DellEMC#show running-config interface port-channel 10 ! interface Port-channel 10 no ip address switchport vlan-stack access vlt-peer-lag port-channel 10 no shutdown DellEMC# DellEMC(conf)#interface port-channel 20 DellEMC(conf-if-po-20)#switchport DellEMC(conf-if-po-20)#vlt-peer-lag port-channel 20 DellEMC(conf-if-po-20)#vlan-stack trunk DellEMC(conf-if-po-20)#no shutdown DellEMC#show running-config interface port-channel 20 ! interface Port-channel 20 no ip address switc
IPv6 Peer Routing in VLT Domains Overview VLT enables the physical links between two devices that are called VLT nodes or peers, and within a VLT domain, to be considered as a single logical link to external devices that are connected using LAG bundles to both the VLT peers. This capability enables redundancy without the implementation of Spanning tree protocol (STP), thereby providing a loop-free network with optimal bandwidth utilization.
Synchronization of IPv6 ND Entries in a Non-VLT Domain Layer 3 VLT provides a higher resiliency at the Layer 3 forwarding level. Routed VLT allows you to replace VRRP with routed VLT to route the traffic from Layer 2 access nodes. With ND synchronization, both the VLT nodes perform Layer 3 forwarding on behalf of each other. Synchronization of NDPM entries learned on non-VLT interfaces between the non-VLT nodes.
Figure 133. Sample Configuration of IPv6 Peer Routing in a VLT Domain Sample Configuration of IPv6 Peer Routing in a VLT Domain Consider a sample scenario as shown in the following figure in which two VLT nodes, Unit1 and Unit2, are connected in a VLT domain using an ICL or VLTi link. To the south of the VLT domain, Unit1 and Unit2 are connected to a ToR switch named Node B. Also, Unit1 is connected to another node, Node A, and Unit2 is linked to a node, Node C.
Figure 134. Sample Configuration of IPv6 Peer Routing in a VLT Domain Neighbor Solicitation from VLT Hosts Consider a case in which NS for VLT node1 IP reaches VLT node1 on the VLT interface and NS for VLT node1 IP reaches VLT node2 due to LAG level hashing in the ToR. When VLT node1 receives NS from VLT VLAN interface, it unicasts the NA packet on the VLT interface. When NS reaches VLT node2, it is flooded on all interfaces including ICL.
Consider a situation in which NA for VLT node1 reaches VLT node1 on a non-VLT interface and NA for VLT node1 reaches VLT node2 on a non-VLT interface. When VLT node1 receives NA on a VLT interface, it learns the Host MAC address on the received interface. This learned neighbor entry is synchronized to VLT node2 as it is learned on ICL.
Non-VLT host to Non-VLT host traffic flow When VLT node receives traffic from non-VLT host intended to the non-VLT host, it does neighbor entry lookup and routes traffic over ICL interface. If traffic reaches wrong VLT peer, it routes the traffic over ICL. Router Solicitation When VLT node receives router Solicitation on VLT interface/non-VLT interface it consumes the packets and will send RA back on the received interface. VLT node will drop the RS message if it is received over ICL interface.
60 VLT Proxy Gateway The virtual link trucking (VLT) proxy gateway feature allows a VLT domain to locally terminate and route L3 packets that are destined to a Layer 3 (L3) end point in another VLT domain. Enable the VLT proxy gateway using the link layer discover protocol (LLDP) method or the static configuration. For more information, see the Command Line Reference Guide.
Figure 135. Sample Configuration for a VLT Proxy Gateway Guidelines for Enabling the VLT Proxy Gateway Keep the following points in mind when you enable a VLT proxy gateway: • Proxy gateway is supported only for VLT; for example, across a VLT domain. • You must enable the VLT peer-routing command for the VLT proxy gateway to function.
• You cannot change the VLT LAG to a legacy LAG when it is part of proxy-gateway. • You cannot change the link layer discovery protocol (LLDP) port channel interface to a legacy LAG when you enable a proxy gateway. • Dell EMC Networking recommends the vlt-peer-mac transmit command only for square VLTs without diagonal links. • The virtual router redundancy (VRRP) protocol and IPv6 routing is not supported. • Private VLANs (PVLANs) are not supported.
• You must configure the interface proxy gateway LLDP to enable or disable a proxy-gateway LLDP TLV on specific interfaces. • The interface is typically a VLT port-channel that connects to a remote VLT domain. • The new proxy gateway TLV is carried on the physical links under the port channel only. • You must have at least one link connection to each unit of the VLT domain. Following are the prerequisites for Proxy Gateway LLDP configuration: • You must globally enable LLDP.
LLDP VLT Proxy Gateway in a Square VLT Topology Figure 136. Sample Configuration for a VLT Proxy Gateway • The preceding figure shows a sample square VLT Proxy gateway topology. There are no diagonal links in the square VLT connection between the C and D in VLT domain 1 and C1 and D1 in the VLT domain 2. This causes sub-optimal routing.
• Any L3 packet, when it gets an L3 hit and is routed, it has a time to live (TTL) decrement as expected. • You can disable the VLT Proxy Gateway for a particular VLAN using an "Exclude-VLAN" configuration. The configuration has to be done in both the VLT domains [C and D in VLT domain 1 and C1 and D1 in VLT domain 2].
Figure 137. VLT Proxy Gateway Sample Topology VLT Domain Configuration Dell-1 and Dell-2 constitute VLT domain 120. Dell-3 and Dell-4 constitute VLT domain 110. These two VLT domains are connected using a VLT LAG P0 50. To know how to configure the interfaces in VLT domains, see the Configuring VLT section. Dell-1 VLT Configuration vlt domain 120 peer-link port-channel 120 back-up destination 10.1.1.
switchport no spanning-tree vlt-peer-lag port-channel 50 no shutdown Note that on the inter-domain link, the switchport command is enabled. On a VLTi link between VLT peers in a VLT domain, the switchport command is not used. VLAN 100 is used as the OSPF peering VLAN between Dell-1 and Dell-2. interface Vlan 100 description OSPF Peering VLAN to Dell-2 ip address 10.10.100.1/30 ip ospf network point-to-point no shutdown VLAN 101 is used as the OSPF peering VLAN between the two VLT domains.
The following output shows that Dell-1 forms OSPF neighborship with Dell-2. Dell-2#sh ip ospf nei Neighbor ID Pri State Dead Time Address Interface Area 4.4.4.4 1 FULL/ - 00:00:33 10.10.100.1 Vl 100 0 Dell-3 VLT Configuration vlt domain 110 peer-link port-channel 110 back-up destination 10.1.1.
The following output shows that Dell-4 and VLT domain 120 form OSPF neighborship with Dell-3. Dell-3#sh ip ospf nei ! Neighbor ID Pri State Dead Time Address Interface Area 4.4.4.4 1 FULL/ - 00:00:33 10.10.101.1 Vl 101 0 1.1.1.1 1 FULL/ - 00:00:34 10.10.102.2 Vl 102 0 Dell-4 VLT Configuration vlt domain 110 peer-link port-channel 110 back-up destination 10.1.1.
61 Virtual Routing and Forwarding (VRF) Virtual Routing and Forwarding (VRF) allows a physical router to partition itself into multiple Virtual Routers (VRs). The control and data plane are isolated in each VR so that traffic does NOT flow across VRs.Virtual Routing and Forwarding (VRF) allows multiple instances of a routing table to co-exist within the same router at the same time. VRF Overview VRF improves functionality by allowing network paths to be segmented without using multiple devices.
Figure 138. VRF Network Example VRF Configuration Notes Although there is no restriction on the number of VLANs that can be assigned to a VRF instance, the total number of routes supported in VRF is limited by the size of the IPv4 CAM. VRF is implemented in a network device by using Forwarding Information Bases (FIBs). A network device may have the ability to configure different virtual routers, where entries in the FIB that belong to one VRF cannot be accessed by another VRF on the same device.
If the next-hop IP in a static route VRF statement is VRRP IP of another VRF, this static route does not get installed on the VRRP master. VRF supports some routing protocols only on the default VRF (default-vrf) instance. Table 1 displays the software features supported in VRF and whether they are supported on all VRF instances or only the default VRF. NOTE: To configure a router ID in a non-default VRF, configure at least one IP address in both the default as well as the nondefault VRF. Table 104.
Feature/Capability Support Status for Default VRF Support Status for Non-default VRF OSPFv3 Yes Yes IS-IS Yes Yes BGP Yes Yes ACL Yes No Multicast No No NDP Yes Yes RAD Yes Yes DHCP DHCP requests are not forwarded across VRF instances. The DHCP client and server must be on the same VRF instance.
Assigning an Interface to a VRF You must enter the ip vrf forwarding command before you configure the IP address or any other setting on an interface. NOTE: You can configure an IP address or subnet on a physical or VLAN interface that overlaps the same IP address or subnet configured on another interface only if the interfaces are assigned to different VRFs. If two interfaces are assigned to the same VRF, you cannot configure overlapping IP subnets or the same IP address on them.
Assigning an OSPF Process to a VRF Instance OSPF routes are supported on all VRF instances. See the Open Shortest Path First (OSPFv2) chapter for complete OSPF configuration information. Assign an OSPF process to a VRF instance . Return to CONFIGURATION mode to enable the OSPF process. The OSPF Process ID is the identifying number assigned to the OSPF process, and the Router ID is the IP address associated with the OSPF process.
Task Command Syntax Command Mode Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 43, Gratuitous ARP sent: 0 Virtual MAC address: 00:00:5e:00:01:0a Virtual IP address: 10.1.1.100 Authentication: (none) Configuring Management VRF You can assign a management interface to a management VRF. NOTE: The loopback interface cannot be added into the management VRF. 1 Create a management VRF. CONFIGURATION ip vrf management 2 Assign a management port to a management VRF.
CONFIGURATION management route ip-address mask managementethernet ormanagement route ipv6-address prefixlength managementethernet You can also have the management route to point to a front-end port in case of the management VRF. For example: management route 2::/64 gigabitethernet 1/1 . • Configure a static entry in the IPv6 neighbor discovery.
Figure 140. Setup VRF Interfaces The following example relates to the configuration shown in the above illustrations. Router 1 ip vrf blue 1 ! ip vrf orange 2 ! ip vrf green 3 ! interface GigabitEthernet 3/1 no ip address switchport no shutdown ! interface GigabitEthernet 1/1 ip vrf forwarding blue ip address 10.0.0.1/24 no shutdown ! interface GigabitEthernet 1/2 ip vrf forwarding orange ip address 20.0.0.
ip vrf forwarding green ip address 30.0.0.1/24 no shutdown ! interface Vlan 128 ip vrf forwarding blue ip address 1.0.0.1/24 tagged GigabitEthernet 3/1 no shutdown ! interface Vlan 192 ip vrf forwarding orange ip address 2.0.0.1/24 tagged GigabitEthernet 3/1 no shutdown ! interface Vlan 256 ip vrf forwarding green ip address 3.0.0.1/24 tagged GigabitEthernet 3/1 no shutdown ! router ospf 1 vrf blue router-id 1.0.0.1 network 1.0.0.0/24 area 0 network 10.0.0.
ip address 2.0.0.2/24 tagged GigabitEthernet 3/1 no shutdown ! interface Vlan 256 ip vrf forwarding green ip address 3.0.0.2/24 tagged GigabitEthernet 3/1 no shutdown ! router ospf 1 vrf blue router-id 1.0.0.2 network 11.0.0.0/24 area 0 network 1.0.0.0/24 area 0 passive-interface GigabitEthernet 2/1 ! router ospf 2 vrf orange router-id 2.0.0.2 network 21.0.0.0/24 area 0 network 2.0.0.0/24 area 0 passive-interface GigabitEthernet 2/2 ! ip route vrf green30.0.0.0/24 3.0.0.
DellEMC#show ip route vrf orange Codes: C - connected, S - static, R - RIP, B - BGP, IN - internal BGP, EX - external BGP,LO - Locally Originated, O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, > - non-active route, + - summary route Gateway of last resort is not set C C O Destination ----------2.0.0.0/24 20.
O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2, E1 - OSPF external type 1, E2 - OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, IA - IS-IS inter area, * - candidate default, > - non-active route, + - summary route Gateway of last resort is not set Destination Gateway ----------------C 1.0.0.0/24 Direct, Vl 128 O 10.0.0.0/24 via 1.0.0.1, Vl 128 C 11.0.0.
interface GigabitEthernet 1/10 ip vrf forwarding VRF2 ip address 140.0.0.1/24 ip route vrf VRF1 20.0.0.0/16 140.0.0.2 vrf VRF2 ip route vrf VRF2 40.0.0.0/16 120.0.0.2 vrf VRF1 Dynamic Route Leaking Route Leaking is a powerful feature that enables communication between isolated (virtual) routing domains by segregating and sharing a set of services such as VOIP, Video, and so on that are available on one routing domain with other virtual domains.
ip vrf forwarding vrf-shared ip address ip—address mask A non-default VRF named VRF-Shared is created and the interface 1/4 is assigned to this VRF. 2 Configure the export target in the source VRF:. ip route-export 1:1 3 Configure VRF-red. ip vrf vrf-red interface-type slot/port ip vrf forwarding VRF-red ip address ip—address mask A non-default VRF named VRF-red is created and the interface is assigned to this VRF. 4 Configure the import target in VRF-red.
ip ! ip vrf ip ip ! ip vrf ! ip vrf ip ip ip route-import 1:1 VRF-Blue route-export route-import 3:3 1:1 VRF-Green VRF-shared route-export route-import route-import 1:1 2:2 3:3 Show routing tables of all the VRFs (without any route-export and route-import tags being configured) DellEMC# show ip route vrf VRF-Red O 11.1.1.1/32 via 111.1.1.1 110/0 C 111.1.1.0/24 Direct, Gi 1/11 0/0 00:00:10 22:39:59 DellEMC# show ip route vrf VRF-Blue O 22.2.2.2/32 via 122.2.2.2 110/0 00:00:11 C 122.2.2.
C 111.1.1.0/24 O 22.2.2.2/32 C 122.2.2.0/24 O 44.4.4.4/32 00:00:11 Direct, VRF-Red:Gi 1/11 0/0 via VRF-Blue:122.2.2.2 110/0 Direct, VRF-Blue:Gi 1/22 0/0 via 144.4.4.4 110/0 C Direct, Gi 1/4 144.4.4.0/24 0/0 22:39:59 00:00:11 22:39:61 00:32:36 Important Points to Remember • If the target VRF conatins the same prefix as either the sourced or Leaked route from some other VRF, then route Leaking for that particular prefix fails and the following error-log is thrown.
ip vrf forwarding VRF-red ip address ip—address mask A non-default VRF named VRF-red is created and the interface is assigned to this VRF. 2 Define a route-map export_ospfbgp_protocol. DellEMC(config)route-map export_ospfbgp_protocol permit 10 3 Define the matching criteria for the exported routes.
O 22.2.2.2/32 00:00:11 via 122.2.2.2 O via vrf-red:144.4.4.4 0/0 00:32:36 << only OSPF and BGP leaked from VRF-red 44.4.4.4/32 110/0 Important Points to Remember • Only Active routes are eligible for leaking. For example, if VRF-A has two routes from BGP and OSPF, in which the BGP route is not active. In this scenario, the OSPF route takes precedence over BGP.
62 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is designed to eliminate a single point of failure in a statically routed network. VRRP Overview VRRP is designed to eliminate a single point of failure in a statically routed network. VRRP specifies a MASTER router that owns the next hop IP and MAC address for end stations on a local area network (LAN).
Figure 141. Basic VRRP Configuration VRRP Benefits With VRRP configured on a network, end-station connectivity to the network is not subject to a single point-of-failure. End-station connections to the network are redundant and are not dependent on internal gateway protocol (IGP) protocols to converge or update routing tables. In conjunction with Virtual Link Trunking (VLT), you can configure optimized forwarding with virtual router redundancy protocol (VRRP).
CAUTION: Increasing the advertisement interval increases the VRRP Master dead interval, resulting in an increased failover time for Master/Backup election. Take caution when increasing the advertisement interval, as the increased dead interval may cause packets to be dropped during that switch-over time. NOTE: In a VLT environment, VRRP configuration acts as active-active and if route is not present in any of the VRRP nodes, the packet to the destination is dropped on that VRRP node. Table 106.
The VRID range is from 1 to 255. • NOTE: The interface must already have a primary IP address defined and be enabled, as shown in the second example. Delete a VRRP group. INTERFACE mode no vrrp-group vrid Examples of Configuring and Verifying VRRP The following examples how to configure VRRP. DellEMC(conf)#interface gigabitethernet 1/1 DellEMC(conf-if-gi-1/1)#vrrp-group 111 DellEMC(conf-if-gi-1/1-vrid-111)# The following examples how to verify the VRRP configuration.
Example: Migrating an IPv4 VRRP Group from VRRPv2 to VRRPv3 NOTE: Carefully following this procedure, otherwise you might introduce dual master switches issues. To migrate an IPv4 VRRP Group from VRRPv2 to VRRPv3: 1 Set the backup switches to VRRP version to both. Dell_backup_switch1(conf-if-gi-1/1-vrid-100)#version both Dell_backup_switch2(conf-if-gi-1/2-vrid-100)#version both 2 Set the master switch to VRRP protocol version 3.
The VRID range is from 1 to 255. 2 Configure virtual IP addresses for this VRID. INTERFACE -VRID mode virtual-address ip-address1 [...ip-address12] The range is up to 12 addresses. Examples of the Configuring and Verifying a Virtual IP Address The following example shows how to configure a virtual IP address. DellEMC(conf-if-gi-1/1-vrid-111)#virtual-address 10.10.10.1 DellEMC(conf-if-gi-1/1-vrid-111)#virtual-address 10.10.10.2 DellEMC(conf-if-gi-1/1-vrid-111)#virtual-address 10.10.10.
Setting VRRP Group (Virtual Router) Priority Setting a virtual router priority to 255 ensures that router is the “owner” virtual router for the VRRP group. VRRP elects the MASTER router by choosing the router with the highest priority. The default priority for a virtual router is 100. The higher the number, the higher the priority. If the MASTER router fails, VRRP begins the election process to choose a new MASTER router based on the next-highest priority.
To configure simple authentication, use the following command. • Configure a simple text password. INTERFACE-VRID mode authentication-type simple [encryption-type] password Parameters: • encryption-type: 0 indicates unencrypted; 7 indicates encrypted. • password: plain text. Examples of the authentication-type Command The bold section shows the encryption type (encrypted) and the password.
no preempt priority 255 virtual-address virtual-address virtual-address virtual-address 10.10.10.1 10.10.10.2 10.10.10.3 10.10.10.10 Changing the Advertisement Interval By default, the MASTER router transmits a VRRP advertisement to all members of the VRRP group every one second, indicating it is operational and is the MASTER router. If the VRRP group misses three consecutive advertisements, the election process begins and the BACKUP virtual router with the highest priority transitions to MASTER.
priority 255 virtual-address virtual-address virtual-address virtual-address 10.10.10.1 10.10.10.2 10.10.10.3 10.10.10.10 Track an Interface or Object You can set Dell EMC Networking OS to monitor the state of any interface according to the virtual group. Each VRRP group can track up to 12 interfaces and up to 20 additional objects, which may affect the priority of the VRRP group. If the tracked interface goes down, the VRRP group’s priority decreases by a default value of 10 (also known as cost).
• (Optional) Display the configuration and the UP or DOWN state of tracked interfaces and objects in VRRP groups, including the time since the last change in an object’s state. EXEC mode or EXEC Privilege mode • show vrrp (Optional) Display the configuration of tracked objects in VRRP groups on a specified interface.
Tracking states for 2 resource Ids: 2 - Up IPv6 route, 2040::/64, priority-cost 20, 00:02:11 3 - Up IPv6 route, 2050::/64, priority-cost 30, 00:02:11 The following example shows verifying the VRRP configuration on an interface.
The default is 0. Sample Configurations Before you set up VRRP, review the following sample configurations. VRRP for an IPv4 Configuration The following configuration shows how to enable IPv4 VRRP. This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. To support your own IP addresses, interfaces, names, and so on, be sure that you make the necessary changes.
Examples of Configuring VRRP for IPv4 and IPv6 The following example shows configuring VRRP for IPv4 Router 2. R2(conf)#interface gigabitethernet 2/31 R2(conf-if-gi-2/31)#ip address 10.1.1.1/24 R2(conf-if-gi-2/31)#vrrp-group 99 R2(conf-if-gi-2/31-vrid-99)#priority 200 R2(conf-if-gi-2/31-vrid-99)#virtual 10.1.1.3 R2(conf-if-gi-2/31-vrid-99)#no shut R2(conf-if-gi-2/31)#show conf ! interface GigabitEthernet 2/31 ip address 10.1.1.1/24 ! vrrp-group 99 priority 200 virtual-address 10.1.1.
Figure 143. VRRP for an IPv6 Configuration NOTE: In a VRRP or VRRPv3 group, if two routers come up with the same priority and another router already has MASTER status, the router with master status continues to be MASTER even if one of two routers has a higher IP or IPv6 address. The following example shows configuring VRRP for IPv6 Router 2 and Router 3. Configure a virtual link local (fe80) address for each VRRPv3 group created for an interface.
R2(conf-if-gi-1/1-vrid-10)#virtual-address fe80::10 R2(conf-if-gi-1/1-vrid-10)#virtual-address 1::10 R2(conf-if-gi-1/1-vrid-10)#no shutdown R2(conf-if-gi-1/1)#show config interface GigabitEthernet 1/1 ipv6 address 1::1/64 vrrp-group 10 priority 100 virtual-address fe80::10 virtual-address 1::10 no shutdown R2(conf-if-gi-1/1)#end R2#show vrrp -----------------GigabitEthernet 1/1, IPv6 VRID: 10, Version: 3, Net:fe80::201:e8ff:fe6a:c59f VRF: 0 default State: Master, Priority: 100, Master: fe80::201:e8ff:fe6a:c
VRRP in a VRF: Non-VLAN Scenario The following example shows how to enable VRRP in a non-VLAN. The following example shows a typical use case in which you create three virtualized overlay networks by configuring three VRFs in two switches. The default gateway to reach the Internet in each VRF is a static route with the next hop being the virtual IP address configured in VRRP. In this scenario, a single VLAN is associated with each VRF.
S1(conf)#ip vrf VRF-3 3 ! S1(conf)#interface GigabitEthernet 1/1 S1(conf-if-gi-1/1)#ip vrf forwarding VRF-1 S1(conf-if-gi-1/1)#ip address 10.10.1.5/24 S1(conf-if-gi-1/1)#vrrp-group 11 % Info: The VRID used by the VRRP group 11 in VRF 1 will be 177. S1(conf-if-gi-1/1-vrid-101)#priority 100 S1(conf-if-gi-1/1-vrid-101)#virtual-address 10.10.1.2 S1(conf-if-gi-1/1)#no shutdown ! S1(conf)#interface GigabitEthernet 1/2 S1(conf-if-gi-1/2)#ip vrf forwarding VRF-2 S1(conf-if-gi-1/2)#ip address 10.10.1.
! S2(conf)#interface GigabitEthernet 1/3 S2(conf-if-gi-1/3)#ip vrf forwarding VRF-3 S2(conf-if-gi-1/3)#ip address 20.1.1.6/24 S2(conf-if-gi-1/3)#vrrp-group 15 % Info: The VRID used by the VRRP group 15 in VRF 3 will be 243. S2(conf-if-gi-1/3-vrid-105)#priority 100 S2(conf-if-gi-1/3-vrid-105)#virtual-address 20.1.1.
DellEMC#show vrrp vrf vrf1 vlan 400 -----------------Vlan 400, IPv4 VRID: 1, Version: 2, Net: 10.1.1.1 VRF: 1 vrf1 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 278, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.100 Authentication: (none) DellEMC#show vrrp vrf vrf2 port-channel 1 -----------------Port-channel 1, IPv4 VRID: 1, Version: 2, Net: 10.1.1.
S2(conf-if-vl-300)#no shutdown DellEMC#show vrrp vrf vrf1 vlan 400 -----------------Vlan 400, IPv4 VRID: 1, Version: 2, Net: 10.1.1.1 VRF: 1 vrf1 State: Master, Priority: 100, Master: 10.1.1.1 (local) Hold Down: 0 sec, Preempt: TRUE, AdvInt: 1 sec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 278, Gratuitous ARP sent: 1 Virtual MAC address: 00:00:5e:00:01:01 Virtual IP address: 10.1.1.100 Authentication: (none) Vlan 400, IPv4 VRID: 10, Version: 2, Net: 20.1.1.
Figure 145. VRRP for IPv6 Topology NOTE: This example does not contain comprehensive directions and is intended to provide guidance for only a typical VRRP configuration. You can copy and paste from the example to your CLI. Be sure you make the necessary changes to support your own IP addresses, interfaces, names, and so on.
NOTE: The virtual IPv6 address you configure should be the same as the IPv6 subnet to which the interface belongs.
Virtual MAC address: 00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe80::255 DellEMC#show vrrp gigabitethernet 2/8 GigabitEthernet 2/8, IPv6 VRID: 255, Version: 3, Net: fe80::201:e8ff:fe8a:e9ed VRF: 0 default State: Master, Priority: 110, Master: fe80::201:e8ff:fe8a:e9ed (local) Hold Down: 0 centisec, Preempt: TRUE, AdvInt: 100 centisec Accept Mode: FALSE, Master AdvInt: 100 centisec Adv rcvd: 0, Bad pkts rcvd: 0, Adv sent: 120 Virtual MAC address: 00:00:5e:00:02:ff Virtual IP address: 10:1:1::255 fe80:
63 Debugging and Diagnostics This chapter describes debugging and diagnostics for the device. Offline Diagnostics The offline diagnostics test suite is useful for isolating faults and debugging hardware. The diagnostics tests are grouped into three levels: • Level 0 — Level 0 diagnostics check for the presence of various components and perform essential path verifications. In addition, Level 0 diagnostics verify the identification registers of the components on the board.
EXEC Privilege mode show system brief 3 Start diagnostics on the unit. diag stack-unit stack-unit-number When the tests are complete, the system displays the following message and automatically reboots the unit. DellEMC#00:09:42 : Diagnostic test results are stored on file: flash:/TestReport-SU-0.txt Diags completed...
Hardware Watchdog Timer The hardware watchdog command automatically reboots an Dell EMC Networking OS switch/router with a single RPM that is unresponsive. This is a last resort mechanism intended to prevent a manual power cycle. Using the Show Hardware Commands The show hardware command tree consists of commands used with the system. These commands display information from a hardware sub-component and from hardware-based feature tables.
EXEC Privilege mode show hardware stack-unit {1–12} unit {0-0} port-stats [detail] • View the stack-unit internal registers for each port-pipe. EXEC Privilege mode show hardware stack-unit {1–12} unit {0-0} register • View the tables from the bShell through the CLI without going into the bShell.
When the system detects a genuine over-temperature condition, it powers off the card. To recognize this condition, look for the following system messages: CHMGR-2-MAJOR_TEMP: Major alarm: chassis temperature high (temperature reaches or exceeds threshold of [value]C) CHMGR-2-TEMP_SHUTDOWN_WARN: WARNING! temperature is [value]C; approaching shutdown threshold of [value]C To view the programmed alarm thresholds levels, including the shutdown value, use the show alarms threshold command.
Table 108. SNMP Traps and OIDs OID String OID Name Description chSysPortXfpRecvPower OID displays the receiving power of the connected optics. chSysPortXfpTxPower OID displays the transmitting power of the connected optics. chSysPortXfpRecvTemp OID displays the temperature of the connected optics. Receiving Power .1.3.6.1.4.1.6027.3.10.1.2.5.1.6 Transmitting power .1.3.6.1.4.1.6027.3.10.1.2.5.1.8 Temperature .1.3.6.1.4.1.6027.3.10.1.2.5.1.
• • • clear hardware stack-unit stack-unit-number unit 0-1 counters clear hardware stack-unit stack-unit-number cpu data-plane statistics clear hardware stack-unit stack-unit-number cpu party-bus statistics Displaying Drop Counters To display drop counters, use the following commands. • • Identify which stack unit and port pipe is experiencing internal drops. show hardware stack-unit stack-unit-number drops [unit unit-number] Identify which interface is experiencing internal drops.
TX Err PKT Counter --- Error counters--Internal Mac Transmit Errors Unknown Opcodes Internal Mac Receive Errors : 0 : 0 : 0 : 0 DellEMC#show hardware stack-unit 1 drops UNIT No: 1 Total Total Total Total Total Ingress Drops IngMac Drops Mmu Drops EgMac Drops Egress Drops : : : : : 6804353 0 124904297 0 0 DellEMC#show hardware stack-unit 1 drops unit 0 UserPort PortNumber Egress Drops 1 1 0 0 2 2 0 0 3 3 0 0 4 4 0 0 5 5 0 0 6 6 0 0 7 7 0 0 8 8 0 0 9 9 0 0 10 10 0 0 11 11 0 0 12 12 0 0 13 13 0 0 14 14 0
26 0 43 0 0 0 44 0 0 0 45 0 0 0 46 0 0 0 47 0 0 0 48 0 0 0 49 0 0 0 50 0 0 0 51 0 0 0 52 0 0 0 61 0 0 0 62 0 0 0 63 0 0 0 64 0 0 0 65 0 0 0 66 0 0 0 67 0 0 0 68 0 0 0 0 0 0 0 0 42 0 0 0 0 0 0 0 41 0 0 0 0 0 0 0 40 0 0 0 0 0 0 0 39 0 0 0 0 0 0 0 38 0 0 0 0 0 0 0 37 0 0 0 0 0 0 0 36 0 0 0 0 0 0 0 35 0 0 0 0 0 0 0 34 0 0 0 0 0 0 0 33 0 0 0 0 0 0 0 32 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 54/1 54/2 54/3 54/4 Internal Internal 69 0 0 0 70 0 0 0 71 0 0 0 72 0 0 0 53 0 0 0 57 4659499 0 0 Dataplane Statistics The show hardware stack-unit cpu data-plane statistics command provides insight into the packet types coming to the CPU. The show hardware stack-unit cpu party-bus statistics command displays input and output statistics on the party bus, which carries inter-process communication traffic between CPUs.
txPkt(COS8 ) txPkt(COS9 ) txPkt(COS10) txPkt(COS11) txPkt(UNIT0) :0 :0 :0 :0 :0 Example of Viewing Party Bus Statistics DellEMC#sh hardware stack-unit 1 cpu party-bus statistics Input Statistics: 27550 packets, 2559298 bytes 0 dropped, 0 errors Output Statistics: 1649566 packets, 1935316203 bytes 0 errors Display Stack Port Statistics The show hardware stack-unit stack-port command displays input and output statistics for a stack-port interface.
RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX RX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX TX - 4096 to 9216 Byte Frame Counter Good Packet Counter Packet/frame Counter Unicast Packet Counter Multicast Packet Counter Broadcast Frame Counter Byte Counter Control frame counter PAUSE frame counter Oversized frame counter Jabber frame counter VLAN tag frame counter Double VLAN tag frame counter RUNT frame counter Fragment counter VLAN tagged packets 64 Byte Frame Counter 64 to 127 By
RX - 1519 to 2047 Byte Frame Counter RX - 2048 to 4095 Byte Frame Counter RX - 4096 to 9216 Byte Frame Counter RX - Good Packet Counter RX - Packet/Frame Counter RX - Unicast Frame Counter RX - Multicast Frame Counter RX - Broadcast Frame Counter RX - Byte Counter RX - Control Frame Counter RX - Pause Control Frame Counter RX - Oversized Frame Counter RX - Jabber Frame Counter RX - VLAN Tag Frame Counter RX - Double VLAN Tag Frame Counter RX - RUNT Frame Counter RX - Fragment Counter RX - VLAN Tagged Packet
The panic string contains key information regarding the crash. Several panic string types exist, and they are displayed in regular English text to enable easier understanding of the crash cause. Example of Application Mini Core Dump Listings DellEMC#dir flash:/CORE_DUMP_DIR Directory of flash:/CORE_DUMP_DIR 1 2 3 4 drwx drwx drwx -rwx 4096 4096 4096 512 Jan Jan Jan May 07 01 07 11 2015 1980 2015 2015 13:25:04 00:00:00 13:25:04 20:54:24 +00:00 +00:00 +00:00 +00:00 . .. FTP_STK_MEMBER f10StkUnit.
64 Standards Compliance This chapter describes standards compliance for Dell EMC Networking products. NOTE: Unless noted, when a standard cited here is listed as supported by the Dell EMC Networking OS, the system also supports predecessor standards. One way to search for predecessor standards is to use the http://tools.ietf.org/ website. Click “Browse and search IETF documents,” enter an RFC number, and inspect the top of the resulting document for obsolescence citations to related RFCs.
Force10 PVST+ SFF-8431 SFP+ Direct Attach Cable (10GSFP+Cu) MTU 12,000 bytes RFC and I-D Compliance Dell EMC Networking OS supports the following standards. The standards are grouped by related protocol. The columns showing support by platform indicate which version of Dell EMC Networking OS first supports the standard. General Internet Protocols The following table lists the Dell EMC Networking OS support per platform for general internet protocols. Table 109.
R F C # Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 24 Definition of 7.7.1 74 the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 26 PPP over 15 SONET/SDH 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 26 A Two Rate 9 Three Color 8 Marker 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.
General IPv4 Protocols The following table lists the Dell EMC Networking OS support per platform for general IPv4 protocols. Table 110. General IPv4 Protocols RF C# Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 791 Internet Protocol 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 826 An Ethernet Address Resolution 7.6.1 Protocol 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.
General IPv6 Protocols The following table lists the Dell EMC Networking OS support per platform for general IPv6 protocols. Table 111. General IPv6 Protocols RFC # Full Name S-Series 1886 DNS Extensions to support IP 7.8.1 version 6 S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 1981 Path MTU Discovery for IP (Part version 6 ial) 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.
Border Gateway Protocol (BGP) The following table lists the Dell EMC Networking OS support per platform for BGP protocols. Table 112. Border Gateway Protocol (BGP) RFC# Full Name S-Series/ZSeries S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 1997 BGP ComAmtturnibituitees 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2385 Protection of BGP Sessions via the TCP MD5 Signature Option 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2439 BGP Route Flap Damping 7.8.
Open Shortest Path First (OSPF) The following table lists the Dell EMC Networking OS support per platform for OSPF protocol. Table 113. Open Shortest Path First (OSPF) RFC # Full Name S-Series/ZSeries S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 1587 The OSPF Not-SoStubby Area (NSSA) Option 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2154 OSPF with Digital Signatures 7.6.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 2370 The OSPF Opaque LSA Option 7.6.1 9.8(0.
RFC# Full Name S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 3784 Intermediate System to Intermediate System (IS-IS) Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS) 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 5120 MT-ISIS: Multi Topology (MT) 9.8(0.0P2) Routing in Intermediate System to Intermediate Systems (ISISs) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 5306 Restart Signaling for IS-IS 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.
Multicast The following table lists the Dell EMC Networking OS support per platform for Multicast protocol. Table 116. Multicast RFC# Full Name S-Series S3048–ON S4048–ON Z9100–ON S4048T-ON S6010–ON 1112 Host Extensions for IP Multicasting 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.8(1.0) 9.8(1.0) 2236 Internet Group Management Protocol, Version 2 7.8.1 9.8(0.0P2) 9.8(0.0P5) 9.8(1.0) 9.10(0.1) 9.10(0.1) 3376 Internet Group Management Protocol, Version 3 7.8.1 9.8(0.0P2) 9.8(0.
65 X.509v3 supports X.509v3 standards. Topics: • • • • • • • • • Introduction to X.509v3 certification X.509v3 support in Information about installing CA certificates Information about Creating Certificate Signing Requests (CSR) Information about installing trusted certificates Transport layer security (TLS) Online Certificate Status Protocol (OSCP) Verifying certificates Event logging Introduction to X.509v3 certification X.
1 An entity or organization that wants a digital certificate requests one through a CSR. 2 To request a digital certificate through a CSR, a key pair is generated and the CSR is signed using the secret private key. The CSR contains information identifying the applicant and the applicant's public key. This public key is used to verify the signature of the CSR and the Distinguished Name (DN). 3 This CSR is sent to a Certificate Authority (CA).
The Root CA generates a private key and a self-signed CA certificate. The Intermediate CA generates a private key and a Certificate Signing Request (CSR). Using its private key, the root CA signs the intermediate CA’s CSR generating a CA certificate for the Intermediate CA. This intermediate CA can then sign certificates for hosts in the network and also for further intermediate CAs.
During the initial TLS protocol negotiation, both participating parties also check to see if the other’s certificate is revoked by the CA. To do this check, the devices query the CA’s designated OCSP responder on the network. The OCSP responder information is included in the presented certificate, the Intermediate CA inserts the info upon signing it, or it may be statically configured on the host. Information about installing CA certificates Dell EMC Networking OS enables you to download and install X.
If you do not specify the cert-file option, the system prompts you to enter metadata information related to the CSR as follows: You are about to be asked to enter information that will be incorporated into your certificate request. What you are about to enter is what is called a Distinguished Name or a DN. There are quite a few fields but you can leave some blank. For some fields there will be a default value; if you enter '.', the field will be left blank.
NOTE: The command contains multiple options with the Common Name being a required field and blanks being filled in for unspecified fields. Information about installing trusted certificates Dell EMC Networking OS also enables you to install a trusted certificate. The system can then present this certificate for authentication to clients such as SSH and HTTPS. This trusted certificate is also presented to the TLS server implementations that require client authentication such as Syslog.
TLS_ECDH_RSA_WITH_AES_256_CBC_SHA TLS_ECDH_RSA_WITH_AES_128_CBC_SHA TLS_DH_RSA_WITH_AES_256_CBC_SHA TLS_DH_RSA_WITH_AES_128_CBC_SHA TLS compression is disabled by default. TLS session resumption is also supported to reduce processor and traffic overhead due to public key cryptographic operations and handshake traffic. However, the maximum time allowed for a TLS session to resume without repeating the TLS authentication or handshake process is configurable with a default of 1 hour.
NOTE: If you have an IPv6 address in the URL, then enclose this address in square brackets. For example, http:// [1100::203]:6514. Configuring OCSP behavior You can configure how the OCSP requests and responses are signed when the CA or the device contacts the OCSP responders. To configure this behavior, follow this step: In CONFIGURATION mode, enter the following command: crypto x509 ocsp {[nonce] [sign-request]} Both the none and sign-request parameters are optional.
Verifying Server certificates Verifying server certificates is mandatory in the TLS protocol. As a result, all TLS-enabled applications require certificate verification, including Syslog servers. The system checks the Server certificates against installed CA certificates. NOTE: As part of the certificate verification, the hostname or IP address of the server is verified against the hostname or IP address specified in the application.
